#include <common.h>
#include <palmas.h>
#include <sata.h>
+#include <asm/gpio.h>
+#include <asm/arch/gpio.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/mmc_host_def.h>
#include <asm/arch/sata.h>
+#include <environment.h>
#include "mux_data.h"
DECLARE_GLOBAL_DATA_PTR;
+/* GPIO 7_11 */
+#define GPIO_DDR_VTT_EN 203
+
const struct omap_sysinfo sysinfo = {
"Board: DRA7xx\n"
};
int board_late_init(void)
{
- init_sata(0);
- return 0;
-}
-
-/**
- * @brief misc_init_r - Configure EVM board specific configurations
- * such as power configurations, ethernet initialization as phase2 of
- * boot sequence
- *
- * @return 0
- */
-int misc_init_r(void)
-{
+#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+ if (omap_revision() == DRA722_ES1_0)
+ setenv("board_name", "dra72x");
+ else
+ setenv("board_name", "dra7xx");
+#endif
return 0;
}
}
#endif
+#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT)
+int spl_start_uboot(void)
+{
+ /* break into full u-boot on 'c' */
+ if (serial_tstc() && serial_getc() == 'c')
+ return 1;
+
+#ifdef CONFIG_SPL_ENV_SUPPORT
+ env_init();
+ env_relocate_spec();
+ if (getenv_yesno("boot_os") != 1)
+ return 1;
+#endif
+
+ return 0;
+}
+#endif
+
#ifdef CONFIG_DRIVER_TI_CPSW
/* Delay value to add to calibrated value */
#define VIN2A_D15_DLY_VAL ((0x4 << 5) + 0x0)
#define VIN2A_D14_DLY_VAL ((0x4 << 5) + 0x0)
+extern u32 *const omap_si_rev;
+
static void cpsw_control(int enabled)
{
/* VTP can be added here */
{
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
- .phy_id = 0,
+ .phy_addr = 2,
},
{
.slave_reg_ofs = 0x308,
.sliver_reg_ofs = 0xdc0,
- .phy_id = 1,
+ .phy_addr = 3,
},
};
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
- .slaves = 1,
+ .slaves = 2,
.slave_data = cpsw_slaves,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
if (is_valid_ether_addr(mac_addr))
eth_setenv_enetaddr("ethaddr", mac_addr);
}
+
+ mac_lo = readl((*ctrl)->control_core_mac_id_1_lo);
+ mac_hi = readl((*ctrl)->control_core_mac_id_1_hi);
+ mac_addr[0] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = mac_hi & 0xFF;
+ mac_addr[3] = (mac_lo & 0xFF0000) >> 16;
+ mac_addr[4] = (mac_lo & 0xFF00) >> 8;
+ mac_addr[5] = mac_lo & 0xFF;
+
+ if (!getenv("eth1addr")) {
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("eth1addr", mac_addr);
+ }
+
ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33);
ctrl_val |= 0x22;
writel(ctrl_val, (*ctrl)->control_core_control_io1);
+ if (*omap_si_rev == DRA722_ES1_0)
+ cpsw_data.active_slave = 1;
+
ret = cpsw_register(&cpsw_data);
if (ret < 0)
printf("Error %d registering CPSW switch\n", ret);
return ret;
}
#endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+/* VTT regulator enable */
+static inline void vtt_regulator_enable(void)
+{
+ if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL)
+ return;
+
+ /* Do not enable VTT for DRA722 */
+ if (omap_revision() == DRA722_ES1_0)
+ return;
+
+ /*
+ * EVM Rev G and later use gpio7_11 for DDR3 termination.
+ * This is safe enough to do on older revs.
+ */
+ gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en");
+ gpio_direction_output(GPIO_DDR_VTT_EN, 1);
+}
+
+int board_early_init_f(void)
+{
+ vtt_regulator_enable();
+ return 0;
+}
+#endif