* Copyright (C) 1998 Dan Malek <dmalek@jlc.net>
* Copyright (C) 1999 Magnus Damm <kieraypc01.p.y.kie.era.ericsson.se>
* Copyright (C) 2000 Wolfgang Denk <wd@denx.de>
- * Copyright (C) 2001 Alex ZΓΌpke <azu@sysgo.de>
+ * Copyright (C) 2001 Alex Zuepke <azu@sysgo.de>
* Copyright (C) 2002 Kyle Harris <kharris@nexus-tech.net>
- * Copyright (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
- * Copyright (C) 2003 Kai-Uwe Bloehm <kai-uwe.bloem@auerswald.de>
+ * Copyright (C) 2003 Robert Schwebel <r.schwebel@pengutronix.de>
+ * Copyright (C) 2003 Kai-Uwe Bloem <kai-uwe.bloem@auerswald.de>
*
* See file CREDITS for list of people who contributed to this
* project.
#include <config.h>
#include <version.h>
+#include <asm/arch/pxa-regs.h>
.globl _start
_start: b reset
/*
* Startup Code (reset vector)
*
- * do important init only if we don't start from memory!
+ * do important init only if we don't start from RAM!
* - relocate armboot to ram
* - setup stack
* - jump to second stage
.word _start
/*
- * Note: _armboot_end_data and _armboot_end are defined
- * by the (board-dependent) linker script.
- * _armboot_end_data is the first usable FLASH address after armboot
- */
-.globl _armboot_end_data
-_armboot_end_data:
- .word armboot_end_data
-.globl _armboot_end
-_armboot_end:
- .word armboot_end
-
-/*
- * This is defined in the board specific linker script
+ * These are defined in the board-specific linker script.
*/
.globl _bss_start
_bss_start:
- .word bss_start
+ .word __bss_start
.globl _bss_end
_bss_end:
- .word bss_end
-
-/*
- * _armboot_real_end is the first usable RAM address behind armboot
- * and the various stacks
- */
-.globl _armboot_real_end
-_armboot_real_end:
- .word 0x0badc0de
-
-/*
- * We relocate uboot to this address (end of RAM - 128 KiB)
- */
-.globl _uboot_reloc
-_uboot_reloc:
- .word TEXT_BASE
+ .word _end
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
orr r0,r0,#0x13
msr cpsr,r0
+ /*
+ * we do sys-critical inits only at reboot,
+ * not when booting from ram!
+ */
+#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit /* we do sys-critical inits */
+#endif
+#ifndef CONFIG_SKIP_RELOCATE_UBOOT
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
- cmp r0, r1 /* don't reloc during debug */
- beq stack_setup
+ cmp r0, r1 /* don't reloc during debug */
+ beq stack_setup
ldr r2, _armboot_start
- ldr r3, _armboot_end
- sub r2, r3, r2 /* r2 <- size of armboot */
- add r2, r0, r2 /* r2 <- source end address */
+ ldr r3, _bss_start
+ sub r2, r3, r2 /* r2 <- size of armboot */
+ add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end addreee [r2] */
ble copy_loop
+#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
/* Set up the stack */
-
stack_setup:
-
- ldr r0, _uboot_reloc /* upper 128 KiB: relocated uboot */
+ ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
sub r0, r0, #CFG_MALLOC_LEN /* malloc area */
- /* FIXME: bdinfo should be here */
+ sub r0, r0, #CFG_GBL_DATA_SIZE /* bdinfo */
+#ifdef CONFIG_USE_IRQ
+ sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ)
+#endif
sub sp, r0, #12 /* leave 3 words for abort-stack */
clear_bss:
+ ldr r0, _bss_start /* find start of bss segment */
+ ldr r1, _bss_end /* stop here */
+ mov r2, #0x00000000 /* clear */
- ldr r0, _bss_start /* find start of bss segment */
- add r0, r0, #4 /* start at first byte of bss */
- ldr r1, _bss_end /* stop here */
- mov r2, #0x00000000 /* clear */
-
-clbss_l:str r2, [r0] /* clear loop... */
+clbss_l:str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
- bne clbss_l
-
+ ble clbss_l
ldr pc, _start_armboot
/* - setup memory timing */
/* */
/****************************************************************************/
+/* mk@tbd: Fix this! */
+#if defined(CONFIG_PXA250) || defined(CONFIG_CPU_MONAHANS)
+#undef ICMR
+#undef OSMR3
+#undef OSCR
+#undef OWER
+#undef OIER
+#endif
+#ifdef CONFIG_PXA250
+#undef RCSR
+#undef CCCR
+#endif
-/* Interrupt-Controller base address */
+/* Interrupt-Controller base address */
IC_BASE: .word 0x40d00000
#define ICMR 0x04
#define OWER 0x18
#define OIER 0x1C
-/* Clock Manager Registers */
+/* Clock Manager Registers */
+#ifdef CONFIG_CPU_MONAHANS
+# ifndef CFG_MONAHANS_RUN_MODE_OSC_RATIO
+# error "You have to define CFG_MONAHANS_RUN_MODE_OSC_RATIO!!"
+# endif
+# ifndef CFG_MONAHANS_TURBO_RUN_MODE_RATIO
+# define CFG_MONAHANS_TURBO_RUN_MODE_RATIO 0x1
+# endif
+#else /* ! CONFIG_CPU_MONAHANS */
+#ifdef CFG_CPUSPEED
CC_BASE: .word 0x41300000
#define CCCR 0x00
cpuspeed: .word CFG_CPUSPEED
+#else
+#error "You have to define CFG_CPUSPEED!!"
+#endif
+#endif /* CONFIG_CPU_MONAHANS */
-
- /* RS: ??? */
- .macro CPWAIT
- mrc p15,0,r0,c2,c0,0
- mov r0,r0
+ /* takes care the CP15 update has taken place */
+ .macro CPWAIT reg
+ mrc p15,0,\reg,c2,c0,0
+ mov \reg,\reg
sub pc,pc,#4
.endm
-
cpu_init_crit:
/* mask all IRQs */
+#ifndef CONFIG_CPU_MONAHANS
ldr r0, IC_BASE
mov r1, #0x00
str r1, [r0, #ICMR]
-
-#if defined(CFG_CPUSPEED)
+#else
+ /* Step 1 - Enable CP6 permission */
+ mrc p15, 0, r1, c15, c1, 0 @ read CPAR
+ orr r1, r1, #0x40
+ mcr p15, 0, r1, c15, c1, 0
+ CPWAIT r1
+
+ /* Step 2 - Mask ICMR & ICMR2 */
+ mov r1, #0
+ mcr p6, 0, r1, c1, c0, 0 @ ICMR
+ mcr p6, 0, r1, c7, c0, 0 @ ICMR2
+
+ /* turn off all clocks but the ones we will definitly require */
+ ldr r1, =CKENA
+ ldr r2, =(CKENA_22_FFUART | CKENA_10_SRAM | CKENA_9_SMC | CKENA_8_DMC)
+ str r2, [r1]
+ ldr r1, =CKENB
+ ldr r2, =(CKENB_6_IRQ)
+ str r2, [r1]
+#endif
/* set clock speed */
+#ifdef CONFIG_CPU_MONAHANS
+ ldr r0, =ACCR
+ ldr r1, =(((CFG_MONAHANS_TURBO_RUN_MODE_RATIO<<8) & ACCR_XN_MASK) | (CFG_MONAHANS_RUN_MODE_OSC_RATIO & ACCR_XL_MASK))
+ str r1, [r0]
+#else /* ! CONFIG_CPU_MONAHANS */
+#ifdef CFG_CPUSPEED
ldr r0, CC_BASE
ldr r1, cpuspeed
str r1, [r0, #CCCR]
mcr p14, 0, r0, c6, c0, 0
setspeed_done:
-#endif
+
+#endif /* CFG_CPUSPEED */
+#endif /* CONFIG_CPU_MONAHANS */
/*
* before relocating, we have to setup RAM timing
* because memory timing is board-dependend, you will
- * find a memsetup.S in your board directory.
+ * find a lowlevel_init.S in your board directory.
*/
mov ip, lr
- bl memsetup
+ bl lowlevel_init
mov lr, ip
/* Memory interfaces are working. Disable MMU and enable I-cache. */
+ /* mk: hmm, this is not in the monahans docs, leave it now but
+ * check here if it doesn't work :-) */
ldr r0, =0x2001 /* enable access to all coproc. */
mcr p15, 0, r0, c15, c1, 0
- CPWAIT
+ CPWAIT r0
mcr p15, 0, r0, c7, c10, 4 /* drain the write & fill buffers */
- CPWAIT
+ CPWAIT r0
mcr p15, 0, r0, c7, c7, 0 /* flush Icache, Dcache and BTB */
- CPWAIT
+ CPWAIT r0
mcr p15, 0, r0, c8, c7, 0 /* flush instuction and data TLBs */
- CPWAIT
+ CPWAIT r0
/* Enable the Icache */
/*
stmia sp, {r0 - r12} /* Calling r0-r12 */
add r8, sp, #S_PC
- ldr r2, _armboot_end
- add r2, r2, #CONFIG_STACKSIZE
- sub r2, r2, #8
+ ldr r2, _armboot_start
+ sub r2, r2, #(CONFIG_STACKSIZE+CFG_MALLOC_LEN)
+ sub r2, r2, #(CFG_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
ldmia r2, {r2 - r4} /* get pc, cpsr, old_r0 */
add r0, sp, #S_FRAME_SIZE /* restore sp_SVC */
.endm
.macro get_bad_stack
- ldr r13, _armboot_end @ setup our mode stack
- add r13, r13, #CONFIG_STACKSIZE @ resides at top of normal stack
- sub r13, r13, #8
+ ldr r13, _armboot_start @ setup our mode stack
+ sub r13, r13, #(CONFIG_STACKSIZE+CFG_MALLOC_LEN)
+ sub r13, r13, #(CFG_GBL_DATA_SIZE+8) @ reserved a couple spots in abort stack
str lr, [r13] @ save caller lr / spsr
mrs lr, spsr
#endif
/****************************************************************************/
-/* */
+/* */
/* Reset function: the PXA250 doesn't have a reset function, so we have to */
-/* perform a watchdog timeout for a soft reset. */
-/* */
+/* perform a watchdog timeout for a soft reset. */
+/* */
/****************************************************************************/
.align 5
.globl reset_cpu
- /* FIXME: this code is PXA250 specific. How is this handled on */
- /* other XScale processors? */
+ /* FIXME: this code is PXA250 specific. How is this handled on */
+ /* other XScale processors? */
reset_cpu:
ldr r0, OSTIMER_BASE
ldr r1, [r0, #OWER]
- orr r1, r1, #0x0001 /* bit0: WME */
+ orr r1, r1, #0x0001 /* bit0: WME */
str r1, [r0, #OWER]
/* OS timer does only wrap every 1165 seconds, so we have to set */
- /* the match register as well. */
+ /* the match register as well. */
- ldr r1, [r0, #OSCR] /* read OS timer */
+ ldr r1, [r0, #OSCR] /* read OS timer */
add r1, r1, #0x800 /* let OSMR3 match after */
add r1, r1, #0x800 /* 4096*(1/3.6864MHz)=1ms */
str r1, [r0, #OSMR3]