drivers/phy: Add Marvell SerDes / PHY drivers used on Armada 3k

[karo-tx-uboot.git] / doc / README.uniphier

diff --git a/doc/README.uniphier b/doc/README.uniphier
index bce70cf5fe433ecb64e77b21f4973658a695f788..49045a02188aa214bf1bcd555747e5bc28f92733 100644 (file)
--- a/doc/README.uniphier
+++ b/doc/README.uniphier
@@ -44,9 +44,17 @@ PH1-Pro4 reference board:
     $ make uniphier_pro4_defconfig
     $ make CROSS_COMPILE=arm-linux-gnueabi-
 
+PH1-Pro4 Ace board:
+    $ make uniphier_pro4_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro4-ace
+
+PH1-Pro4 Sanji board:
+    $ make uniphier_pro4_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro4-sanji
+
 PH1-Pro5 4KBOX Board:
-    $ make uniphier_pro5_defconfig
-    $ make CROSS_COMPILE=arm-linux-gnueabi-
+    $ make uniphier_pxs2_ld6b_defconfig
+    $ make CROSS_COMPILE=arm-linux-gnueabi- DEVICE_TREE=uniphier-ph1-pro5-4kbox
 
 ProXstream2 Gentil board:
     $ make uniphier_pxs2_ld6b_defconfig
@@ -67,17 +75,41 @@ to use your favorite compiler.
 Burn U-Boot images to NAND
 --------------------------
 
-Write two files to the NAND device as follows:
- - spl/u-boot-spl-dtb.bin at the offset address 0x00000000
- - u-boot-dtb.img         at the offset address 0x00010000
+Write the following to the NAND device:
+
+ - spl/u-boot-spl.bin at the offset address 0x00000000
+ - u-boot.bin         at the offset address 0x00010000
+
+or
+
+ - u-boot-with-spl.bin at the offset address 0x00000000
 
 If a TFTP server is available, the images can be easily updated.
-Just copy the u-boot-spl-dtb.bin and u-boot-dtb.img to the TFTP public
-directory, and then run the following command at the U-Boot command line:
+Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory,
+and then run the following command at the U-Boot command line:
 
   => run nandupdate
 
 
+Burn U-Boot images to eMMC
+--------------------------
+
+Write the following to the Boot partition 1 of the eMMC device:
+
+ - spl/u-boot-spl.bin at the offset address 0x00000000
+ - u-boot.bin         at the offset address 0x00010000
+
+or
+
+ - u-boot-with-spl.bin at the offset address 0x00000000
+
+If a TFTP server is available, the images can be easily updated.
+Just copy the u-boot-spl.bin and u-boot.bin to the TFTP public directory,
+and then run the following command at the U-Boot command line:
+
+  => run emmcupdate
+
+
 UniPhier specific commands
 --------------------------
 
@@ -93,8 +125,10 @@ Supported devices
 
  - UART (on-chip)
  - NAND
+ - SD/eMMC
  - USB 2.0 (EHCI)
  - USB 3.0 (xHCI)
+ - GPIO
  - LAN (on-board SMSC9118)
  - I2C
  - EEPROM (connected to the on-board I2C bus)
@@ -145,4 +179,4 @@ newer SoCs.  Even if it is, EA[25] is not connected on most of the boards.
 
 --
 Masahiro Yamada <yamada.masahiro@socionext.com>
-Aug. 2015
+Feb. 2016