/*
* sata_mv.c - Marvell SATA support
*
- * Copyright 2008: Marvell Corporation, all rights reserved.
+ * Copyright 2008-2009: Marvell Corporation, all rights reserved.
* Copyright 2005: EMC Corporation, all rights reserved.
* Copyright 2005 Red Hat, Inc. All rights reserved.
*
+ * Originally written by Brett Russ.
+ * Extensive overhaul and enhancement by Mark Lord <mlord@pobox.com>.
+ *
* Please ALWAYS copy linux-ide@vger.kernel.org on emails.
*
* This program is free software; you can redistribute it and/or modify
/*
* sata_mv TODO list:
*
- * --> Errata workaround for NCQ device errors.
- *
* --> More errata workarounds for PCI-X.
*
* --> Complete a full errata audit for all chipsets to identify others.
*
- * --> ATAPI support (Marvell claims the 60xx/70xx chips can do it).
- *
* --> Develop a low-power-consumption strategy, and implement it.
*
- * --> [Experiment, low priority] Investigate interrupt coalescing.
- * Quite often, especially with PCI Message Signalled Interrupts (MSI),
- * the overhead reduced by interrupt mitigation is quite often not
- * worth the latency cost.
+ * --> Add sysfs attributes for per-chip / per-HC IRQ coalescing thresholds.
*
* --> [Experiment, Marvell value added] Is it possible to use target
* mode to cross-connect two Linux boxes with Marvell cards? If so,
#include <linux/libata.h>
#define DRV_NAME "sata_mv"
-#define DRV_VERSION "1.25"
+#define DRV_VERSION "1.27"
+
+/*
+ * module options
+ */
+
+static int msi;
+#ifdef CONFIG_PCI
+module_param(msi, int, S_IRUGO);
+MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
+#endif
+
+static int irq_coalescing_io_count;
+module_param(irq_coalescing_io_count, int, S_IRUGO);
+MODULE_PARM_DESC(irq_coalescing_io_count,
+ "IRQ coalescing I/O count threshold (0..255)");
+
+static int irq_coalescing_usecs;
+module_param(irq_coalescing_usecs, int, S_IRUGO);
+MODULE_PARM_DESC(irq_coalescing_usecs,
+ "IRQ coalescing time threshold in usecs");
enum {
/* BAR's are enumerated in terms of pci_resource_start() terms */
MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */
MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */
+ /* For use with both IRQ coalescing methods ("all ports" or "per-HC" */
+ COAL_CLOCKS_PER_USEC = 150, /* for calculating COAL_TIMEs */
+ MAX_COAL_TIME_THRESHOLD = ((1 << 24) - 1), /* internal clocks count */
+ MAX_COAL_IO_COUNT = 255, /* completed I/O count */
+
MV_PCI_REG_BASE = 0,
- MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */
- MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08),
- MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88),
- MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c),
- MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc),
- MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0),
+
+ /*
+ * Per-chip ("all ports") interrupt coalescing feature.
+ * This is only for GEN_II / GEN_IIE hardware.
+ *
+ * Coalescing defers the interrupt until either the IO_THRESHOLD
+ * (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
+ */
+ MV_COAL_REG_BASE = 0x18000,
+ MV_IRQ_COAL_CAUSE = (MV_COAL_REG_BASE + 0x08),
+ ALL_PORTS_COAL_IRQ = (1 << 4), /* all ports irq event */
+
+ MV_IRQ_COAL_IO_THRESHOLD = (MV_COAL_REG_BASE + 0xcc),
+ MV_IRQ_COAL_TIME_THRESHOLD = (MV_COAL_REG_BASE + 0xd0),
+
+ /*
+ * Registers for the (unused here) transaction coalescing feature:
+ */
+ MV_TRAN_COAL_CAUSE_LO = (MV_COAL_REG_BASE + 0x88),
+ MV_TRAN_COAL_CAUSE_HI = (MV_COAL_REG_BASE + 0x8c),
MV_SATAHC0_REG_BASE = 0x20000,
MV_FLASH_CTL_OFS = 0x1046c,
/* Host Flags */
MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */
- MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */
MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
- ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI |
- ATA_FLAG_PIO_POLLING,
+ ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING,
+
+ MV_GEN_I_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NO_ATAPI,
- MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE,
+ MV_GEN_II_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NCQ |
+ ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA,
- MV_GENIIE_FLAGS = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | ATA_FLAG_AN,
+ MV_GEN_IIE_FLAGS = MV_GEN_II_FLAGS | ATA_FLAG_AN,
CRQB_FLAG_READ = (1 << 0),
CRQB_TAG_SHIFT = 1,
PCI_HC_MAIN_IRQ_MASK_OFS = 0x1d64,
SOC_HC_MAIN_IRQ_CAUSE_OFS = 0x20020,
SOC_HC_MAIN_IRQ_MASK_OFS = 0x20024,
- ERR_IRQ = (1 << 0), /* shift by port # */
- DONE_IRQ = (1 << 1), /* shift by port # */
+ ERR_IRQ = (1 << 0), /* shift by (2 * port #) */
+ DONE_IRQ = (1 << 1), /* shift by (2 * port #) */
HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */
HC_SHIFT = 9, /* bits 9-17 = HC1's ports */
+ DONE_IRQ_0_3 = 0x000000aa, /* DONE_IRQ ports 0,1,2,3 */
+ DONE_IRQ_4_7 = (DONE_IRQ_0_3 << HC_SHIFT), /* 4,5,6,7 */
PCI_ERR = (1 << 18),
- TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */
- TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */
- PORTS_0_3_COAL_DONE = (1 << 8),
- PORTS_4_7_COAL_DONE = (1 << 17),
- PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */
+ TRAN_COAL_LO_DONE = (1 << 19), /* transaction coalescing */
+ TRAN_COAL_HI_DONE = (1 << 20), /* transaction coalescing */
+ PORTS_0_3_COAL_DONE = (1 << 8), /* HC0 IRQ coalescing */
+ PORTS_4_7_COAL_DONE = (1 << 17), /* HC1 IRQ coalescing */
+ ALL_PORTS_COAL_DONE = (1 << 21), /* GEN_II(E) IRQ coalescing */
GPIO_INT = (1 << 22),
SELF_INT = (1 << 23),
TWSI_INT = (1 << 24),
HC_COAL_IRQ = (1 << 4), /* IRQ coalescing */
DEV_IRQ = (1 << 8), /* shift by port # */
+ /*
+ * Per-HC (Host-Controller) interrupt coalescing feature.
+ * This is present on all chip generations.
+ *
+ * Coalescing defers the interrupt until either the IO_THRESHOLD
+ * (count of completed I/Os) is met, or the TIME_THRESHOLD is met.
+ */
+ HC_IRQ_COAL_IO_THRESHOLD_OFS = 0x000c,
+ HC_IRQ_COAL_TIME_THRESHOLD_OFS = 0x0010,
+
+ SOC_LED_CTRL_OFS = 0x2c,
+ SOC_LED_CTRL_BLINK = (1 << 0), /* Active LED blink */
+ SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex dev presence */
+ /* with dev activity LED */
+
/* Shadow block registers */
SHD_BLK_OFS = 0x100,
SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */
EDMA_ARB_CFG_OFS = 0x38,
EDMA_HALTCOND_OFS = 0x60, /* GenIIe halt conditions */
+ EDMA_UNKNOWN_RSVD_OFS = 0x6C, /* GenIIe unknown/reserved */
+
+ BMDMA_CMD_OFS = 0x224, /* bmdma command register */
+ BMDMA_STATUS_OFS = 0x228, /* bmdma status register */
+ BMDMA_PRD_LOW_OFS = 0x22c, /* bmdma PRD addr 31:0 */
+ BMDMA_PRD_HIGH_OFS = 0x230, /* bmdma PRD addr 63:32 */
/* Host private flags (hp_flags) */
MV_HP_FLAG_MSI = (1 << 0),
MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */
MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */
MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */
+ MV_HP_QUIRK_LED_BLINK_EN = (1 << 12), /* is led blinking enabled? */
/* Port private flags (pp_flags) */
MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */
MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */
MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */
MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */
+ MV_PP_FLAG_FAKE_ATA_BUSY = (1 << 4), /* ignore initial ATA_DRDY */
};
#define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I)
__le32 reserved;
};
+/*
+ * We keep a local cache of a few frequently accessed port
+ * registers here, to avoid having to read them (very slow)
+ * when switching between EDMA and non-EDMA modes.
+ */
+struct mv_cached_regs {
+ u32 fiscfg;
+ u32 ltmode;
+ u32 haltcond;
+ u32 unknown_rsvd;
+};
+
struct mv_port_priv {
struct mv_crqb *crqb;
dma_addr_t crqb_dma;
unsigned int resp_idx;
u32 pp_flags;
+ struct mv_cached_regs cached;
unsigned int delayed_eh_pmp_map;
};
unsigned int port_no);
static int mv_stop_edma(struct ata_port *ap);
static int mv_stop_edma_engine(void __iomem *port_mmio);
-static void mv_edma_cfg(struct ata_port *ap, int want_ncq);
+static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma);
static void mv_pmp_select(struct ata_port *ap, int pmp);
static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class,
static void mv_process_crpb_entries(struct ata_port *ap,
struct mv_port_priv *pp);
+static void mv_sff_irq_clear(struct ata_port *ap);
+static int mv_check_atapi_dma(struct ata_queued_cmd *qc);
+static void mv_bmdma_setup(struct ata_queued_cmd *qc);
+static void mv_bmdma_start(struct ata_queued_cmd *qc);
+static void mv_bmdma_stop(struct ata_queued_cmd *qc);
+static u8 mv_bmdma_status(struct ata_port *ap);
+static u8 mv_sff_check_status(struct ata_port *ap);
+
/* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below
* because we have to allow room for worst case splitting of
* PRDs for 64K boundaries in mv_fill_sg().
static struct ata_port_operations mv5_ops = {
.inherits = &ata_sff_port_ops,
+ .lost_interrupt = ATA_OP_NULL,
+
.qc_defer = mv_qc_defer,
.qc_prep = mv_qc_prep,
.qc_issue = mv_qc_issue,
.pmp_softreset = mv_softreset,
.softreset = mv_softreset,
.error_handler = mv_pmp_error_handler,
+
+ .sff_check_status = mv_sff_check_status,
+ .sff_irq_clear = mv_sff_irq_clear,
+ .check_atapi_dma = mv_check_atapi_dma,
+ .bmdma_setup = mv_bmdma_setup,
+ .bmdma_start = mv_bmdma_start,
+ .bmdma_stop = mv_bmdma_stop,
+ .bmdma_status = mv_bmdma_status,
};
static struct ata_port_operations mv_iie_ops = {
static const struct ata_port_info mv_port_info[] = {
{ /* chip_504x */
- .flags = MV_COMMON_FLAGS,
+ .flags = MV_GEN_I_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_508x */
- .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_5080 */
- .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv5_ops,
},
{ /* chip_604x */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ,
+ .flags = MV_GEN_II_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_608x */
- .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS |
- ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA |
- ATA_FLAG_NCQ | MV_FLAG_DUAL_HC,
+ .flags = MV_GEN_II_FLAGS | MV_FLAG_DUAL_HC,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv6_ops,
},
{ /* chip_6042 */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_7042 */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
},
{ /* chip_soc */
- .flags = MV_GENIIE_FLAGS,
+ .flags = MV_GEN_IIE_FLAGS,
.pio_mask = 0x1f, /* pio0-4 */
.udma_mask = ATA_UDMA6,
.port_ops = &mv_iie_ops,
return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1);
}
+/**
+ * mv_save_cached_regs - (re-)initialize cached port registers
+ * @ap: the port whose registers we are caching
+ *
+ * Initialize the local cache of port registers,
+ * so that reading them over and over again can
+ * be avoided on the hotter paths of this driver.
+ * This saves a few microseconds each time we switch
+ * to/from EDMA mode to perform (eg.) a drive cache flush.
+ */
+static void mv_save_cached_regs(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_port_priv *pp = ap->private_data;
+
+ pp->cached.fiscfg = readl(port_mmio + FISCFG_OFS);
+ pp->cached.ltmode = readl(port_mmio + LTMODE_OFS);
+ pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+ pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD_OFS);
+}
+
+/**
+ * mv_write_cached_reg - write to a cached port register
+ * @addr: hardware address of the register
+ * @old: pointer to cached value of the register
+ * @new: new value for the register
+ *
+ * Write a new value to a cached register,
+ * but only if the value is different from before.
+ */
+static inline void mv_write_cached_reg(void __iomem *addr, u32 *old, u32 new)
+{
+ if (new != *old) {
+ *old = new;
+ writel(new, addr);
+ }
+}
+
static void mv_set_edma_ptrs(void __iomem *port_mmio,
struct mv_host_priv *hpriv,
struct mv_port_priv *pp)
port_mmio + EDMA_RSP_Q_OUT_PTR_OFS);
}
+static void mv_write_main_irq_mask(u32 mask, struct mv_host_priv *hpriv)
+{
+ /*
+ * When writing to the main_irq_mask in hardware,
+ * we must ensure exclusivity between the interrupt coalescing bits
+ * and the corresponding individual port DONE_IRQ bits.
+ *
+ * Note that this register is really an "IRQ enable" register,
+ * not an "IRQ mask" register as Marvell's naming might suggest.
+ */
+ if (mask & (ALL_PORTS_COAL_DONE | PORTS_0_3_COAL_DONE))
+ mask &= ~DONE_IRQ_0_3;
+ if (mask & (ALL_PORTS_COAL_DONE | PORTS_4_7_COAL_DONE))
+ mask &= ~DONE_IRQ_4_7;
+ writelfl(mask, hpriv->main_irq_mask_addr);
+}
+
static void mv_set_main_irq_mask(struct ata_host *host,
u32 disable_bits, u32 enable_bits)
{
new_mask = (old_mask & ~disable_bits) | enable_bits;
if (new_mask != old_mask) {
hpriv->main_irq_mask = new_mask;
- writelfl(new_mask, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(new_mask, hpriv);
}
}
mv_set_main_irq_mask(ap->host, disable_bits, enable_bits);
}
+static void mv_clear_and_enable_port_irqs(struct ata_port *ap,
+ void __iomem *port_mmio,
+ unsigned int port_irqs)
+{
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ int hardport = mv_hardport_from_port(ap->port_no);
+ void __iomem *hc_mmio = mv_hc_base_from_port(
+ mv_host_base(ap->host), ap->port_no);
+ u32 hc_irq_cause;
+
+ /* clear EDMA event indicators, if any */
+ writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
+
+ /* clear pending irq events */
+ hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
+ writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
+
+ /* clear FIS IRQ Cause */
+ if (IS_GEN_IIE(hpriv))
+ writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+
+ mv_enable_port_irqs(ap, port_irqs);
+}
+
+static void mv_set_irq_coalescing(struct ata_host *host,
+ unsigned int count, unsigned int usecs)
+{
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *mmio = hpriv->base, *hc_mmio;
+ u32 coal_enable = 0;
+ unsigned long flags;
+ unsigned int clks, is_dual_hc = hpriv->n_ports > MV_PORTS_PER_HC;
+ const u32 coal_disable = PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE |
+ ALL_PORTS_COAL_DONE;
+
+ /* Disable IRQ coalescing if either threshold is zero */
+ if (!usecs || !count) {
+ clks = count = 0;
+ } else {
+ /* Respect maximum limits of the hardware */
+ clks = usecs * COAL_CLOCKS_PER_USEC;
+ if (clks > MAX_COAL_TIME_THRESHOLD)
+ clks = MAX_COAL_TIME_THRESHOLD;
+ if (count > MAX_COAL_IO_COUNT)
+ count = MAX_COAL_IO_COUNT;
+ }
+
+ spin_lock_irqsave(&host->lock, flags);
+ mv_set_main_irq_mask(host, coal_disable, 0);
+
+ if (is_dual_hc && !IS_GEN_I(hpriv)) {
+ /*
+ * GEN_II/GEN_IIE with dual host controllers:
+ * one set of global thresholds for the entire chip.
+ */
+ writel(clks, mmio + MV_IRQ_COAL_TIME_THRESHOLD);
+ writel(count, mmio + MV_IRQ_COAL_IO_THRESHOLD);
+ /* clear leftover coal IRQ bit */
+ writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+ if (count)
+ coal_enable = ALL_PORTS_COAL_DONE;
+ clks = count = 0; /* force clearing of regular regs below */
+ }
+
+ /*
+ * All chips: independent thresholds for each HC on the chip.
+ */
+ hc_mmio = mv_hc_base_from_port(mmio, 0);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (count)
+ coal_enable |= PORTS_0_3_COAL_DONE;
+ if (is_dual_hc) {
+ hc_mmio = mv_hc_base_from_port(mmio, MV_PORTS_PER_HC);
+ writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD_OFS);
+ writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD_OFS);
+ writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE_OFS);
+ if (count)
+ coal_enable |= PORTS_4_7_COAL_DONE;
+ }
+
+ mv_set_main_irq_mask(host, 0, coal_enable);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
/**
- * mv_start_dma - Enable eDMA engine
+ * mv_start_edma - Enable eDMA engine
* @base: port base address
* @pp: port private data
*
* LOCKING:
* Inherited from caller.
*/
-static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio,
+static void mv_start_edma(struct ata_port *ap, void __iomem *port_mmio,
struct mv_port_priv *pp, u8 protocol)
{
int want_ncq = (protocol == ATA_PROT_NCQ);
}
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) {
struct mv_host_priv *hpriv = ap->host->private_data;
- int hardport = mv_hardport_from_port(ap->port_no);
- void __iomem *hc_mmio = mv_hc_base_from_port(
- mv_host_base(ap->host), ap->port_no);
- u32 hc_irq_cause;
-
- /* clear EDMA event indicators, if any */
- writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS);
- /* clear pending irq events */
- hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport);
- writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS);
-
- mv_edma_cfg(ap, want_ncq);
-
- /* clear FIS IRQ Cause */
- if (IS_GEN_IIE(hpriv))
- writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS);
+ mv_edma_cfg(ap, want_ncq, 1);
mv_set_edma_ptrs(port_mmio, hpriv, pp);
- mv_enable_port_irqs(ap, DONE_IRQ|ERR_IRQ);
+ mv_clear_and_enable_port_irqs(ap, port_mmio, DONE_IRQ|ERR_IRQ);
writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS);
pp->pp_flags |= MV_PP_FLAG_EDMA_EN;
{
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
+ int err = 0;
if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN))
return 0;
mv_wait_for_edma_empty_idle(ap);
if (mv_stop_edma_engine(port_mmio)) {
ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n");
- return -EIO;
+ err = -EIO;
}
- return 0;
+ mv_edma_cfg(ap, 0, 0);
+ return err;
}
#ifdef ATA_DEBUG
return ATA_DEFER_PORT;
}
-static void mv_config_fbs(void __iomem *port_mmio, int want_ncq, int want_fbs)
+static void mv_config_fbs(struct ata_port *ap, int want_ncq, int want_fbs)
{
- u32 new_fiscfg, old_fiscfg;
- u32 new_ltmode, old_ltmode;
- u32 new_haltcond, old_haltcond;
+ struct mv_port_priv *pp = ap->private_data;
+ void __iomem *port_mmio;
- old_fiscfg = readl(port_mmio + FISCFG_OFS);
- old_ltmode = readl(port_mmio + LTMODE_OFS);
- old_haltcond = readl(port_mmio + EDMA_HALTCOND_OFS);
+ u32 fiscfg, *old_fiscfg = &pp->cached.fiscfg;
+ u32 ltmode, *old_ltmode = &pp->cached.ltmode;
+ u32 haltcond, *old_haltcond = &pp->cached.haltcond;
- new_fiscfg = old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
- new_ltmode = old_ltmode & ~LTMODE_BIT8;
- new_haltcond = old_haltcond | EDMA_ERR_DEV;
+ ltmode = *old_ltmode & ~LTMODE_BIT8;
+ haltcond = *old_haltcond | EDMA_ERR_DEV;
if (want_fbs) {
- new_fiscfg = old_fiscfg | FISCFG_SINGLE_SYNC;
- new_ltmode = old_ltmode | LTMODE_BIT8;
+ fiscfg = *old_fiscfg | FISCFG_SINGLE_SYNC;
+ ltmode = *old_ltmode | LTMODE_BIT8;
if (want_ncq)
- new_haltcond &= ~EDMA_ERR_DEV;
+ haltcond &= ~EDMA_ERR_DEV;
else
- new_fiscfg |= FISCFG_WAIT_DEV_ERR;
+ fiscfg |= FISCFG_WAIT_DEV_ERR;
+ } else {
+ fiscfg = *old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR);
}
- if (new_fiscfg != old_fiscfg)
- writelfl(new_fiscfg, port_mmio + FISCFG_OFS);
- if (new_ltmode != old_ltmode)
- writelfl(new_ltmode, port_mmio + LTMODE_OFS);
- if (new_haltcond != old_haltcond)
- writelfl(new_haltcond, port_mmio + EDMA_HALTCOND_OFS);
+ port_mmio = mv_ap_base(ap);
+ mv_write_cached_reg(port_mmio + FISCFG_OFS, old_fiscfg, fiscfg);
+ mv_write_cached_reg(port_mmio + LTMODE_OFS, old_ltmode, ltmode);
+ mv_write_cached_reg(port_mmio + EDMA_HALTCOND_OFS, old_haltcond, haltcond);
}
static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq)
writel(new, hpriv->base + MV_GPIO_PORT_CTL_OFS);
}
-static void mv_edma_cfg(struct ata_port *ap, int want_ncq)
+/**
+ * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma
+ * @ap: Port being initialized
+ *
+ * There are two DMA modes on these chips: basic DMA, and EDMA.
+ *
+ * Bit-0 of the "EDMA RESERVED" register enables/disables use
+ * of basic DMA on the GEN_IIE versions of the chips.
+ *
+ * This bit survives EDMA resets, and must be set for basic DMA
+ * to function, and should be cleared when EDMA is active.
+ */
+static void mv_bmdma_enable_iie(struct ata_port *ap, int enable_bmdma)
+{
+ struct mv_port_priv *pp = ap->private_data;
+ u32 new, *old = &pp->cached.unknown_rsvd;
+
+ if (enable_bmdma)
+ new = *old | 1;
+ else
+ new = *old & ~1;
+ mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD_OFS, old, new);
+}
+
+/*
+ * SOC chips have an issue whereby the HDD LEDs don't always blink
+ * during I/O when NCQ is enabled. Enabling a special "LED blink" mode
+ * of the SOC takes care of it, generating a steady blink rate when
+ * any drive on the chip is active.
+ *
+ * Unfortunately, the blink mode is a global hardware setting for the SOC,
+ * so we must use it whenever at least one port on the SOC has NCQ enabled.
+ *
+ * We turn "LED blink" off when NCQ is not in use anywhere, because the normal
+ * LED operation works then, and provides better (more accurate) feedback.
+ *
+ * Note that this code assumes that an SOC never has more than one HC onboard.
+ */
+static void mv_soc_led_blink_enable(struct ata_port *ap)
+{
+ struct ata_host *host = ap->host;
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *hc_mmio;
+ u32 led_ctrl;
+
+ if (hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN)
+ return;
+ hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN;
+ hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+ writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
+static void mv_soc_led_blink_disable(struct ata_port *ap)
+{
+ struct ata_host *host = ap->host;
+ struct mv_host_priv *hpriv = host->private_data;
+ void __iomem *hc_mmio;
+ u32 led_ctrl;
+ unsigned int port;
+
+ if (!(hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN))
+ return;
+
+ /* disable led-blink only if no ports are using NCQ */
+ for (port = 0; port < hpriv->n_ports; port++) {
+ struct ata_port *this_ap = host->ports[port];
+ struct mv_port_priv *pp = this_ap->private_data;
+
+ if (pp->pp_flags & MV_PP_FLAG_NCQ_EN)
+ return;
+ }
+
+ hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN;
+ hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no);
+ led_ctrl = readl(hc_mmio + SOC_LED_CTRL_OFS);
+ writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL_OFS);
+}
+
+static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma)
{
u32 cfg;
struct mv_port_priv *pp = ap->private_data;
/* set up non-NCQ EDMA configuration */
cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */
- pp->pp_flags &= ~MV_PP_FLAG_FBS_EN;
+ pp->pp_flags &=
+ ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY);
if (IS_GEN_I(hpriv))
cfg |= (1 << 8); /* enab config burst size mask */
*/
want_fbs &= want_ncq;
- mv_config_fbs(port_mmio, want_ncq, want_fbs);
+ mv_config_fbs(ap, want_ncq, want_fbs);
if (want_fbs) {
pp->pp_flags |= MV_PP_FLAG_FBS_EN;
}
cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */
- cfg |= (1 << 22); /* enab 4-entry host queue cache */
- if (!IS_SOC(hpriv))
- cfg |= (1 << 18); /* enab early completion */
+ if (want_edma) {
+ cfg |= (1 << 22); /* enab 4-entry host queue cache */
+ if (!IS_SOC(hpriv))
+ cfg |= (1 << 18); /* enab early completion */
+ }
if (hpriv->hp_flags & MV_HP_CUT_THROUGH)
cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */
+ mv_bmdma_enable_iie(ap, !want_edma);
+
+ if (IS_SOC(hpriv)) {
+ if (want_ncq)
+ mv_soc_led_blink_enable(ap);
+ else
+ mv_soc_led_blink_disable(ap);
+ }
}
if (want_ncq) {
cfg |= EDMA_CFG_NCQ;
pp->pp_flags |= MV_PP_FLAG_NCQ_EN;
- } else
- pp->pp_flags &= ~MV_PP_FLAG_NCQ_EN;
+ }
writelfl(cfg, port_mmio + EDMA_CFG_OFS);
}
pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0];
}
}
+ mv_save_cached_regs(ap);
+ mv_edma_cfg(ap, 0, 0);
return 0;
out_port_free_dma_mem:
u32 offset = addr & 0xffff;
u32 len = sg_len;
- if ((offset + sg_len > 0x10000))
+ if (offset + len > 0x10000)
len = 0x10000 - offset;
mv_sg->addr = cpu_to_le32(addr & 0xffffffff);
mv_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16);
mv_sg->flags_size = cpu_to_le32(len & 0xffff);
+ mv_sg->reserved = 0;
sg_len -= len;
addr += len;
if (likely(last_sg))
last_sg->flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL);
+ mb(); /* ensure data structure is visible to the chipset */
}
static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last)
*cmdw = cpu_to_le16(tmp);
}
+/**
+ * mv_sff_irq_clear - Clear hardware interrupt after DMA.
+ * @ap: Port associated with this ATA transaction.
+ *
+ * We need this only for ATAPI bmdma transactions,
+ * as otherwise we experience spurious interrupts
+ * after libata-sff handles the bmdma interrupts.
+ */
+static void mv_sff_irq_clear(struct ata_port *ap)
+{
+ mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), ERR_IRQ);
+}
+
+/**
+ * mv_check_atapi_dma - Filter ATAPI cmds which are unsuitable for DMA.
+ * @qc: queued command to check for chipset/DMA compatibility.
+ *
+ * The bmdma engines cannot handle speculative data sizes
+ * (bytecount under/over flow). So only allow DMA for
+ * data transfer commands with known data sizes.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static int mv_check_atapi_dma(struct ata_queued_cmd *qc)
+{
+ struct scsi_cmnd *scmd = qc->scsicmd;
+
+ if (scmd) {
+ switch (scmd->cmnd[0]) {
+ case READ_6:
+ case READ_10:
+ case READ_12:
+ case WRITE_6:
+ case WRITE_10:
+ case WRITE_12:
+ case GPCMD_READ_CD:
+ case GPCMD_SEND_DVD_STRUCTURE:
+ case GPCMD_SEND_CUE_SHEET:
+ return 0; /* DMA is safe */
+ }
+ }
+ return -EOPNOTSUPP; /* use PIO instead */
+}
+
+/**
+ * mv_bmdma_setup - Set up BMDMA transaction
+ * @qc: queued command to prepare DMA for.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_setup(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ struct mv_port_priv *pp = ap->private_data;
+
+ mv_fill_sg(qc);
+
+ /* clear all DMA cmd bits */
+ writel(0, port_mmio + BMDMA_CMD_OFS);
+
+ /* load PRD table addr. */
+ writel((pp->sg_tbl_dma[qc->tag] >> 16) >> 16,
+ port_mmio + BMDMA_PRD_HIGH_OFS);
+ writelfl(pp->sg_tbl_dma[qc->tag],
+ port_mmio + BMDMA_PRD_LOW_OFS);
+
+ /* issue r/w command */
+ ap->ops->sff_exec_command(ap, &qc->tf);
+}
+
+/**
+ * mv_bmdma_start - Start a BMDMA transaction
+ * @qc: queued command to start DMA on.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_start(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE);
+ u32 cmd = (rw ? 0 : ATA_DMA_WR) | ATA_DMA_START;
+
+ /* start host DMA transaction */
+ writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+}
+
+/**
+ * mv_bmdma_stop - Stop BMDMA transfer
+ * @qc: queued command to stop DMA on.
+ *
+ * Clears the ATA_DMA_START flag in the bmdma control register
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static void mv_bmdma_stop(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 cmd;
+
+ /* clear start/stop bit */
+ cmd = readl(port_mmio + BMDMA_CMD_OFS);
+ cmd &= ~ATA_DMA_START;
+ writelfl(cmd, port_mmio + BMDMA_CMD_OFS);
+
+ /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */
+ ata_sff_dma_pause(ap);
+}
+
+/**
+ * mv_bmdma_status - Read BMDMA status
+ * @ap: port for which to retrieve DMA status.
+ *
+ * Read and return equivalent of the sff BMDMA status register.
+ *
+ * LOCKING:
+ * Inherited from caller.
+ */
+static u8 mv_bmdma_status(struct ata_port *ap)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 reg, status;
+
+ /*
+ * Other bits are valid only if ATA_DMA_ACTIVE==0,
+ * and the ATA_DMA_INTR bit doesn't exist.
+ */
+ reg = readl(port_mmio + BMDMA_STATUS_OFS);
+ if (reg & ATA_DMA_ACTIVE)
+ status = ATA_DMA_ACTIVE;
+ else
+ status = (reg & ATA_DMA_ERR) | ATA_DMA_INTR;
+ return status;
+}
+
/**
* mv_qc_prep - Host specific command preparation.
* @qc: queued command to prepare
mv_fill_sg(qc);
}
+/**
+ * mv_sff_check_status - fetch device status, if valid
+ * @ap: ATA port to fetch status from
+ *
+ * When using command issue via mv_qc_issue_fis(),
+ * the initial ATA_BUSY state does not show up in the
+ * ATA status (shadow) register. This can confuse libata!
+ *
+ * So we have a hook here to fake ATA_BUSY for that situation,
+ * until the first time a BUSY, DRQ, or ERR bit is seen.
+ *
+ * The rest of the time, it simply returns the ATA status register.
+ */
+static u8 mv_sff_check_status(struct ata_port *ap)
+{
+ u8 stat = ioread8(ap->ioaddr.status_addr);
+ struct mv_port_priv *pp = ap->private_data;
+
+ if (pp->pp_flags & MV_PP_FLAG_FAKE_ATA_BUSY) {
+ if (stat & (ATA_BUSY | ATA_DRQ | ATA_ERR))
+ pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY;
+ else
+ stat = ATA_BUSY;
+ }
+ return stat;
+}
+
+/**
+ * mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register
+ * @fis: fis to be sent
+ * @nwords: number of 32-bit words in the fis
+ */
+static unsigned int mv_send_fis(struct ata_port *ap, u32 *fis, int nwords)
+{
+ void __iomem *port_mmio = mv_ap_base(ap);
+ u32 ifctl, old_ifctl, ifstat;
+ int i, timeout = 200, final_word = nwords - 1;
+
+ /* Initiate FIS transmission mode */
+ old_ifctl = readl(port_mmio + SATA_IFCTL_OFS);
+ ifctl = 0x100 | (old_ifctl & 0xf);
+ writelfl(ifctl, port_mmio + SATA_IFCTL_OFS);
+
+ /* Send all words of the FIS except for the final word */
+ for (i = 0; i < final_word; ++i)
+ writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+
+ /* Flag end-of-transmission, and then send the final word */
+ writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL_OFS);
+ writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS_OFS);
+
+ /*
+ * Wait for FIS transmission to complete.
+ * This typically takes just a single iteration.
+ */
+ do {
+ ifstat = readl(port_mmio + SATA_IFSTAT_OFS);
+ } while (!(ifstat & 0x1000) && --timeout);
+
+ /* Restore original port configuration */
+ writelfl(old_ifctl, port_mmio + SATA_IFCTL_OFS);
+
+ /* See if it worked */
+ if ((ifstat & 0x3000) != 0x1000) {
+ ata_port_printk(ap, KERN_WARNING,
+ "%s transmission error, ifstat=%08x\n",
+ __func__, ifstat);
+ return AC_ERR_OTHER;
+ }
+ return 0;
+}
+
+/**
+ * mv_qc_issue_fis - Issue a command directly as a FIS
+ * @qc: queued command to start
+ *
+ * Note that the ATA shadow registers are not updated
+ * after command issue, so the device will appear "READY"
+ * if polled, even while it is BUSY processing the command.
+ *
+ * So we use a status hook to fake ATA_BUSY until the drive changes state.
+ *
+ * Note: we don't get updated shadow regs on *completion*
+ * of non-data commands. So avoid sending them via this function,
+ * as they will appear to have completed immediately.
+ *
+ * GEN_IIE has special registers that we could get the result tf from,
+ * but earlier chipsets do not. For now, we ignore those registers.
+ */
+static unsigned int mv_qc_issue_fis(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct mv_port_priv *pp = ap->private_data;
+ struct ata_link *link = qc->dev->link;
+ u32 fis[5];
+ int err = 0;
+
+ ata_tf_to_fis(&qc->tf, link->pmp, 1, (void *)fis);
+ err = mv_send_fis(ap, fis, sizeof(fis) / sizeof(fis[0]));
+ if (err)
+ return err;
+
+ switch (qc->tf.protocol) {
+ case ATAPI_PROT_PIO:
+ pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY;
+ /* fall through */
+ case ATAPI_PROT_NODATA:
+ ap->hsm_task_state = HSM_ST_FIRST;
+ break;
+ case ATA_PROT_PIO:
+ pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY;
+ if (qc->tf.flags & ATA_TFLAG_WRITE)
+ ap->hsm_task_state = HSM_ST_FIRST;
+ else
+ ap->hsm_task_state = HSM_ST;
+ break;
+ default:
+ ap->hsm_task_state = HSM_ST_LAST;
+ break;
+ }
+
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ ata_pio_queue_task(ap, qc, 0);
+ return 0;
+}
+
/**
* mv_qc_issue - Initiate a command to the host
* @qc: queued command to start
*/
static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
{
+ static int limit_warnings = 10;
struct ata_port *ap = qc->ap;
void __iomem *port_mmio = mv_ap_base(ap);
struct mv_port_priv *pp = ap->private_data;
u32 in_index;
+ unsigned int port_irqs;
- if ((qc->tf.protocol != ATA_PROT_DMA) &&
- (qc->tf.protocol != ATA_PROT_NCQ)) {
- static int limit_warnings = 10;
+ pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; /* paranoia */
+
+ switch (qc->tf.protocol) {
+ case ATA_PROT_DMA:
+ case ATA_PROT_NCQ:
+ mv_start_edma(ap, port_mmio, pp, qc->tf.protocol);
+ pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK;
+ in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT;
+
+ /* Write the request in pointer to kick the EDMA to life */
+ writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
+ port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ return 0;
+
+ case ATA_PROT_PIO:
/*
* Errata SATA#16, SATA#24: warn if multiple DRQs expected.
*
": attempting PIO w/multiple DRQ: "
"this may fail due to h/w errata\n");
}
- /*
- * We're about to send a non-EDMA capable command to the
- * port. Turn off EDMA so there won't be problems accessing
- * shadow block, etc registers.
- */
- mv_stop_edma(ap);
- mv_enable_port_irqs(ap, ERR_IRQ);
- mv_pmp_select(ap, qc->dev->link->pmp);
- return ata_sff_qc_issue(qc);
+ /* drop through */
+ case ATA_PROT_NODATA:
+ case ATAPI_PROT_PIO:
+ case ATAPI_PROT_NODATA:
+ if (ap->flags & ATA_FLAG_PIO_POLLING)
+ qc->tf.flags |= ATA_TFLAG_POLLING;
+ break;
}
- mv_start_dma(ap, port_mmio, pp, qc->tf.protocol);
-
- pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK;
- in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT;
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ port_irqs = ERR_IRQ; /* mask device interrupt when polling */
+ else
+ port_irqs = ERR_IRQ | DONE_IRQ; /* unmask all interrupts */
- /* and write the request in pointer to kick the EDMA to life */
- writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index,
- port_mmio + EDMA_REQ_Q_IN_PTR_OFS);
+ /*
+ * We're about to send a non-EDMA capable command to the
+ * port. Turn off EDMA so there won't be problems accessing
+ * shadow block, etc registers.
+ */
+ mv_stop_edma(ap);
+ mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), port_irqs);
+ mv_pmp_select(ap, qc->dev->link->pmp);
- return 0;
+ if (qc->tf.command == ATA_CMD_READ_LOG_EXT) {
+ struct mv_host_priv *hpriv = ap->host->private_data;
+ /*
+ * Workaround for 88SX60x1 FEr SATA#25 (part 2).
+ *
+ * After any NCQ error, the READ_LOG_EXT command
+ * from libata-eh *must* use mv_qc_issue_fis().
+ * Otherwise it might fail, due to chip errata.
+ *
+ * Rather than special-case it, we'll just *always*
+ * use this method here for READ_LOG_EXT, making for
+ * easier testing.
+ */
+ if (IS_GEN_II(hpriv))
+ return mv_qc_issue_fis(qc);
+ }
+ return ata_sff_qc_issue(qc);
}
static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap)
if (pp->pp_flags & MV_PP_FLAG_NCQ_EN)
return NULL;
qc = ata_qc_from_tag(ap, ap->link.active_tag);
- if (qc && (qc->tf.flags & ATA_TFLAG_POLLING))
- qc = NULL;
+ if (qc) {
+ if (qc->tf.flags & ATA_TFLAG_POLLING)
+ qc = NULL;
+ else if (!(qc->flags & ATA_QCFLAG_ACTIVE))
+ qc = NULL;
+ }
return qc;
}
void __iomem *mmio = hpriv->base, *hc_mmio;
unsigned int handled = 0, port;
+ /* If asserted, clear the "all ports" IRQ coalescing bit */
+ if (main_irq_cause & ALL_PORTS_COAL_DONE)
+ writel(~ALL_PORTS_COAL_IRQ, mmio + MV_IRQ_COAL_CAUSE);
+
for (port = 0; port < hpriv->n_ports; port++) {
struct ata_port *ap = host->ports[port];
unsigned int p, shift, hardport, port_cause;
* to ack (only) those ports via hc_irq_cause.
*/
ack_irqs = 0;
+ if (hc_cause & PORTS_0_3_COAL_DONE)
+ ack_irqs = HC_COAL_IRQ;
for (p = 0; p < MV_PORTS_PER_HC; ++p) {
if ((port + p) >= hpriv->n_ports)
break;
/* for MSI: block new interrupts while in here */
if (using_msi)
- writel(0, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(0, hpriv);
main_irq_cause = readl(hpriv->main_irq_cause_addr);
pending_irqs = main_irq_cause & hpriv->main_irq_mask;
else
handled = mv_host_intr(host, pending_irqs);
}
- spin_unlock(&host->lock);
/* for MSI: unmask; interrupt cause bits will retrigger now */
if (using_msi)
- writel(hpriv->main_irq_mask, hpriv->main_irq_mask_addr);
+ mv_write_main_irq_mask(hpriv->main_irq_mask, hpriv);
+
+ spin_unlock(&host->lock);
return IRQ_RETVAL(handled);
}
mv_reset_channel(hpriv, mmio, ap->port_no);
pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN;
+ pp->pp_flags &=
+ ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY);
/* Workaround for errata FEr SATA#10 (part 2) */
do {
extra = HZ; /* only extend it once, max */
}
} while (sstatus != 0x0 && sstatus != 0x113 && sstatus != 0x123);
+ mv_save_cached_regs(ap);
+ mv_edma_cfg(ap, 0, 0);
return rc;
}
* The per-port interrupts get done later as ports are set up.
*/
mv_set_main_irq_mask(host, 0, PCI_ERR);
+ mv_set_irq_coalescing(host, irq_coalescing_io_count,
+ irq_coalescing_usecs);
done:
return rc;
}
.remove = ata_pci_remove_one,
};
-/*
- * module options
- */
-static int msi; /* Use PCI msi; either zero (off, default) or non-zero */
-
-
/* move to PCI layer or libata core? */
static int pci_go_64(struct pci_dev *pdev)
{
MODULE_VERSION(DRV_VERSION);
MODULE_ALIAS("platform:" DRV_NAME);
-#ifdef CONFIG_PCI
-module_param(msi, int, 0444);
-MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)");
-#endif
-
module_init(mv_init);
module_exit(mv_exit);
projects / mv-sheeva.git / blobdiff