# Block device driver configuration
#
-if BLOCK
+menuconfig BLK_DEV
+ bool "Block devices"
+ depends on BLOCK
+ default y
-menu "Block devices"
+if BLK_DEV
config BLK_DEV_FD
tristate "Normal floppy disk support"
To compile this driver as a module, choose M here: the
module will be called z2ram.
-config ATARI_ACSI
- tristate "Atari ACSI support"
- depends on ATARI && BROKEN
- ---help---
- This enables support for the Atari ACSI interface. The driver
- supports hard disks and CD-ROMs, which have 512-byte sectors, or can
- be switched to that mode. Due to the ACSI command format, only disks
- up to 1 GB are supported. Special support for certain ACSI to SCSI
- adapters, which could relax that, isn't included yet. The ACSI
- driver is also the basis for certain other drivers for devices
- attached to the ACSI bus: Atari SLM laser printer, BioNet-100
- Ethernet, and PAMsNet Ethernet. If you want to use one of these
- devices, you need ACSI support, too.
-
- To compile this driver as a module, choose M here: the
- module will be called acsi.
-
-comment "Some devices (e.g. CD jukebox) support multiple LUNs"
- depends on ATARI && ATARI_ACSI
-
-config ACSI_MULTI_LUN
- bool "Probe all LUNs on each ACSI device"
- depends on ATARI_ACSI
- help
- If you have a ACSI device that supports more than one LUN (Logical
- Unit Number), e.g. a CD jukebox, you should say Y here so that all
- will be found by the ACSI driver. An ACSI device with multiple LUNs
- acts logically like multiple ACSI devices. The vast majority of ACSI
- devices have only one LUN, and so most people can say N here and
- should in fact do so, because it is safer.
-
-config ATARI_SLM
- tristate "Atari SLM laser printer support"
- depends on ATARI && ATARI_ACSI!=n
- help
- If you have an Atari SLM laser printer, say Y to include support for
- it in the kernel. Otherwise, say N. This driver is also available as
- a module ( = code which can be inserted in and removed from the
- running kernel whenever you want). The module will be called
- acsi_slm. Be warned: the driver needs much ST-RAM and can cause
- problems due to that fact!
-
config BLK_DEV_XD
tristate "XT hard disk support"
depends on ISA && ISA_DMA_API
config BLK_CPQ_DA
tristate "Compaq SMART2 support"
- depends on PCI
+ depends on PCI && VIRT_TO_BUS
help
This is the driver for Compaq Smart Array controllers. Everyone
using these boards should say Y here. See the file
setups function - apparently needed by the rd_load_image routine
that supposes the filesystem in the image uses a 1024 blocksize.
-config BLK_DEV_INITRD
- bool "Initial RAM filesystem and RAM disk (initramfs/initrd) support"
- depends on BROKEN || !FRV
- help
- The initial RAM filesystem is a ramfs which is loaded by the
- boot loader (loadlin or lilo) and that is mounted as root
- before the normal boot procedure. It is typically used to
- load modules needed to mount the "real" root file system,
- etc. See <file:Documentation/initrd.txt> for details.
-
- If RAM disk support (BLK_DEV_RAM) is also included, this
- also enables initial RAM disk (initrd) support and adds
- 15 Kbytes (more on some other architectures) to the kernel size.
-
- If unsure say Y.
-
config CDROM_PKTCDVD
tristate "Packet writing on CD/DVD media"
depends on !UML
this option is dangerous unless the CD-RW media is known good, as we
don't do deferred write error handling yet.
-source "drivers/s390/block/Kconfig"
-
config ATA_OVER_ETH
tristate "ATA over Ethernet support"
depends on NET
This driver provides Support for ATA over Ethernet block
devices like the Coraid EtherDrive (R) Storage Blade.
-endmenu
+config SUNVDC
+ tristate "Sun Virtual Disk Client support"
+ depends on SUN_LDOMS
+ help
+ Support for virtual disk devices as a client under Sun
+ Logical Domains.
+
+source "drivers/s390/block/Kconfig"
-endif
+endif # BLK_DEV