struct param_type *param;
uint32_t curr_shadow_reg;
-static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn,
- uint32_t write_group, uint32_t use_dm,
- uint32_t all_correct, uint32_t *bit_chk, uint32_t all_ranks);
-
static void set_failing_group_stage(uint32_t group, uint32_t stage,
uint32_t substage)
{
*/
}
+
+/**
+ * rw_mgr_mem_calibrate_write_test_issue() - Issue write test command
+ * @group: Write Group
+ * @use_dm: Use DM
+ *
+ * Issue write test command. Two variants are provided, one that just tests
+ * a write pattern and another that tests datamask functionality.
+ */
+static void rw_mgr_mem_calibrate_write_test_issue(u32 group,
+ u32 test_dm)
+{
+ const u32 quick_write_mode =
+ (STATIC_CALIB_STEPS & CALIB_SKIP_WRITES) &&
+ ENABLE_SUPER_QUICK_CALIBRATION;
+ u32 mcc_instruction;
+ u32 rw_wl_nop_cycles;
+
+ /*
+ * Set counter and jump addresses for the right
+ * number of NOP cycles.
+ * The number of supported NOP cycles can range from -1 to infinity
+ * Three different cases are handled:
+ *
+ * 1. For a number of NOP cycles greater than 0, the RW Mgr looping
+ * mechanism will be used to insert the right number of NOPs
+ *
+ * 2. For a number of NOP cycles equals to 0, the micro-instruction
+ * issuing the write command will jump straight to the
+ * micro-instruction that turns on DQS (for DDRx), or outputs write
+ * data (for RLD), skipping
+ * the NOP micro-instruction all together
+ *
+ * 3. A number of NOP cycles equal to -1 indicates that DQS must be
+ * turned on in the same micro-instruction that issues the write
+ * command. Then we need
+ * to directly jump to the micro-instruction that sends out the data
+ *
+ * NOTE: Implementing this mechanism uses 2 RW Mgr jump-counters
+ * (2 and 3). One jump-counter (0) is used to perform multiple
+ * write-read operations.
+ * one counter left to issue this command in "multiple-group" mode
+ */
+
+ rw_wl_nop_cycles = gbl->rw_wl_nop_cycles;
+
+ if (rw_wl_nop_cycles == -1) {
+ /*
+ * CNTR 2 - We want to execute the special write operation that
+ * turns on DQS right away and then skip directly to the
+ * instruction that sends out the data. We set the counter to a
+ * large number so that the jump is always taken.
+ */
+ writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+
+ /* CNTR 3 - Not used */
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0_WL_1;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_DATA,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ }
+ } else if (rw_wl_nop_cycles == 0) {
+ /*
+ * CNTR 2 - We want to skip the NOP operation and go straight
+ * to the DQS enable instruction. We set the counter to a large
+ * number so that the jump is always taken.
+ */
+ writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+
+ /* CNTR 3 - Not used */
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_DQS,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ }
+ } else {
+ /*
+ * CNTR 2 - In this case we want to execute the next instruction
+ * and NOT take the jump. So we set the counter to 0. The jump
+ * address doesn't count.
+ */
+ writel(0x0, &sdr_rw_load_mgr_regs->load_cntr2);
+ writel(0x0, &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+
+ /*
+ * CNTR 3 - Set the nop counter to the number of cycles we
+ * need to loop for, minus 1.
+ */
+ writel(rw_wl_nop_cycles - 1, &sdr_rw_load_mgr_regs->load_cntr3);
+ if (test_dm) {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ } else {
+ mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ }
+ }
+
+ writel(0, SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RESET_READ_DATAPATH_OFFSET);
+
+ if (quick_write_mode)
+ writel(0x08, &sdr_rw_load_mgr_regs->load_cntr0);
+ else
+ writel(0x40, &sdr_rw_load_mgr_regs->load_cntr0);
+
+ writel(mcc_instruction, &sdr_rw_load_jump_mgr_regs->load_jump_add0);
+
+ /*
+ * CNTR 1 - This is used to ensure enough time elapses
+ * for read data to come back.
+ */
+ writel(0x30, &sdr_rw_load_mgr_regs->load_cntr1);
+
+ if (test_dm) {
+ writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add1);
+ } else {
+ writel(RW_MGR_LFSR_WR_RD_BANK_0_WAIT,
+ &sdr_rw_load_jump_mgr_regs->load_jump_add1);
+ }
+
+ writel(mcc_instruction, (SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RUN_SINGLE_GROUP_OFFSET) +
+ (group << 2));
+}
+
+/**
+ * rw_mgr_mem_calibrate_write_test() - Test writes, check for single/multiple pass
+ * @rank_bgn: Rank number
+ * @write_group: Write Group
+ * @use_dm: Use DM
+ * @all_correct: All bits must be correct in the mask
+ * @bit_chk: Resulting bit mask after the test
+ * @all_ranks: Test all ranks
+ *
+ * Test writes, can check for a single bit pass or multiple bit pass.
+ */
+static int
+rw_mgr_mem_calibrate_write_test(const u32 rank_bgn, const u32 write_group,
+ const u32 use_dm, const u32 all_correct,
+ u32 *bit_chk, const u32 all_ranks)
+{
+ const u32 rank_end = all_ranks ?
+ RW_MGR_MEM_NUMBER_OF_RANKS :
+ (rank_bgn + NUM_RANKS_PER_SHADOW_REG);
+ const u32 shift_ratio = RW_MGR_MEM_DQ_PER_WRITE_DQS /
+ RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS;
+ const u32 correct_mask_vg = param->write_correct_mask_vg;
+
+ u32 tmp_bit_chk, base_rw_mgr;
+ int vg, r;
+
+ *bit_chk = param->write_correct_mask;
+
+ for (r = rank_bgn; r < rank_end; r++) {
+ /* Request to skip the rank */
+ if (param->skip_ranks[r])
+ continue;
+
+ /* Set rank */
+ set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE);
+
+ tmp_bit_chk = 0;
+ for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS - 1;
+ vg >= 0; vg--) {
+ /* Reset the FIFOs to get pointers to known state. */
+ writel(0, &phy_mgr_cmd->fifo_reset);
+
+ rw_mgr_mem_calibrate_write_test_issue(
+ write_group *
+ RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS + vg,
+ use_dm);
+
+ base_rw_mgr = readl(SDR_PHYGRP_RWMGRGRP_ADDRESS);
+ tmp_bit_chk <<= shift_ratio;
+ tmp_bit_chk |= (correct_mask_vg & ~(base_rw_mgr));
+ }
+
+ *bit_chk &= tmp_bit_chk;
+ }
+
+ set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
+ if (all_correct) {
+ debug_cond(DLEVEL == 2,
+ "write_test(%u,%u,ALL) : %u == %u => %i\n",
+ write_group, use_dm, *bit_chk,
+ param->write_correct_mask,
+ *bit_chk == param->write_correct_mask);
+ return *bit_chk == param->write_correct_mask;
+ } else {
+ set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
+ debug_cond(DLEVEL == 2,
+ "write_test(%u,%u,ONE) : %u != %i => %i\n",
+ write_group, use_dm, *bit_chk, 0, *bit_chk != 0);
+ return *bit_chk != 0x00;
+ }
+}
+
/**
* rw_mgr_mem_calibrate_read_test_patterns() - Read back test patterns
* @rank_bgn: Rank number
set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
}
-/*
- * try a read and see if it returns correct data back. has dummy reads
- * inserted into the mix used to align dqs enable. has more thorough checks
- * than the regular read test.
- */
-static uint32_t rw_mgr_mem_calibrate_read_test(uint32_t rank_bgn, uint32_t group,
- uint32_t num_tries, uint32_t all_correct, uint32_t *bit_chk,
- uint32_t all_groups, uint32_t all_ranks)
-{
- uint32_t r, vg;
- uint32_t correct_mask_vg;
- uint32_t tmp_bit_chk;
- uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS :
+/**
+ * rw_mgr_mem_calibrate_read_test() - Perform READ test on single rank
+ * @rank_bgn: Rank number
+ * @group: Read/Write group
+ * @num_tries: Number of retries of the test
+ * @all_correct: All bits must be correct in the mask
+ * @bit_chk: Resulting bit mask after the test
+ * @all_groups: Test all R/W groups
+ * @all_ranks: Test all ranks
+ *
+ * Try a read and see if it returns correct data back. Test has dummy reads
+ * inserted into the mix used to align DQS enable. Test has more thorough
+ * checks than the regular read test.
+ */
+static int
+rw_mgr_mem_calibrate_read_test(const u32 rank_bgn, const u32 group,
+ const u32 num_tries, const u32 all_correct,
+ u32 *bit_chk,
+ const u32 all_groups, const u32 all_ranks)
+{
+ const u32 rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS :
(rank_bgn + NUM_RANKS_PER_SHADOW_REG);
- uint32_t addr;
- uint32_t base_rw_mgr;
+ const u32 quick_read_mode =
+ ((STATIC_CALIB_STEPS & CALIB_SKIP_DELAY_SWEEPS) &&
+ ENABLE_SUPER_QUICK_CALIBRATION);
+ u32 correct_mask_vg = param->read_correct_mask_vg;
+ u32 tmp_bit_chk;
+ u32 base_rw_mgr;
+ u32 addr;
- *bit_chk = param->read_correct_mask;
- correct_mask_vg = param->read_correct_mask_vg;
+ int r, vg, ret;
- uint32_t quick_read_mode = (((STATIC_CALIB_STEPS) &
- CALIB_SKIP_DELAY_SWEEPS) && ENABLE_SUPER_QUICK_CALIBRATION);
+ *bit_chk = param->read_correct_mask;
for (r = rank_bgn; r < rank_end; r++) {
if (param->skip_ranks[r])
&sdr_rw_load_jump_mgr_regs->load_jump_add3);
tmp_bit_chk = 0;
- for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS-1; ; vg--) {
- /* reset the fifos to get pointers to known state */
+ for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS - 1; vg >= 0;
+ vg--) {
+ /* Reset the FIFOs to get pointers to known state. */
writel(0, &phy_mgr_cmd->fifo_reset);
writel(0, SDR_PHYGRP_RWMGRGRP_ADDRESS |
RW_MGR_RESET_READ_DATAPATH_OFFSET);
- tmp_bit_chk = tmp_bit_chk << (RW_MGR_MEM_DQ_PER_READ_DQS
- / RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS);
-
- if (all_groups)
- addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_ALL_GROUPS_OFFSET;
- else
- addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_SINGLE_GROUP_OFFSET;
+ if (all_groups) {
+ addr = SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RUN_ALL_GROUPS_OFFSET;
+ } else {
+ addr = SDR_PHYGRP_RWMGRGRP_ADDRESS |
+ RW_MGR_RUN_SINGLE_GROUP_OFFSET;
+ }
writel(RW_MGR_READ_B2B, addr +
((group * RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS +
vg) << 2));
base_rw_mgr = readl(SDR_PHYGRP_RWMGRGRP_ADDRESS);
- tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr));
-
- if (vg == 0)
- break;
+ tmp_bit_chk <<= RW_MGR_MEM_DQ_PER_READ_DQS /
+ RW_MGR_MEM_VIRTUAL_GROUPS_PER_READ_DQS;
+ tmp_bit_chk |= correct_mask_vg & ~(base_rw_mgr);
}
+
*bit_chk &= tmp_bit_chk;
}
addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_SINGLE_GROUP_OFFSET;
writel(RW_MGR_CLEAR_DQS_ENABLE, addr + (group << 2));
+ set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
+
if (all_correct) {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "%s:%d read_test(%u,ALL,%u) =>\
- (%u == %u) => %lu", __func__, __LINE__, group,
- all_groups, *bit_chk, param->read_correct_mask,
- (long unsigned int)(*bit_chk ==
- param->read_correct_mask));
- return *bit_chk == param->read_correct_mask;
+ ret = (*bit_chk == param->read_correct_mask);
+ debug_cond(DLEVEL == 2,
+ "%s:%d read_test(%u,ALL,%u) => (%u == %u) => %i\n",
+ __func__, __LINE__, group, all_groups, *bit_chk,
+ param->read_correct_mask, ret);
} else {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "%s:%d read_test(%u,ONE,%u) =>\
- (%u != %lu) => %lu\n", __func__, __LINE__,
- group, all_groups, *bit_chk, (long unsigned int)0,
- (long unsigned int)(*bit_chk != 0x00));
- return *bit_chk != 0x00;
+ ret = (*bit_chk != 0x00);
+ debug_cond(DLEVEL == 2,
+ "%s:%d read_test(%u,ONE,%u) => (%u != %u) => %i\n",
+ __func__, __LINE__, group, all_groups, *bit_chk,
+ 0, ret);
}
+
+ return ret;
}
-static uint32_t rw_mgr_mem_calibrate_read_test_all_ranks(uint32_t group,
- uint32_t num_tries, uint32_t all_correct, uint32_t *bit_chk,
- uint32_t all_groups)
+/**
+ * rw_mgr_mem_calibrate_read_test_all_ranks() - Perform READ test on all ranks
+ * @grp: Read/Write group
+ * @num_tries: Number of retries of the test
+ * @all_correct: All bits must be correct in the mask
+ * @all_groups: Test all R/W groups
+ *
+ * Perform a READ test across all memory ranks.
+ */
+static int
+rw_mgr_mem_calibrate_read_test_all_ranks(const u32 grp, const u32 num_tries,
+ const u32 all_correct,
+ const u32 all_groups)
{
- return rw_mgr_mem_calibrate_read_test(0, group, num_tries, all_correct,
- bit_chk, all_groups, 1);
+ u32 bit_chk;
+ return rw_mgr_mem_calibrate_read_test(0, grp, num_tries, all_correct,
+ &bit_chk, all_groups, 1);
}
/**
*/
static int find_vfifo_failing_read(const u32 grp)
{
- u32 v, ret, bit_chk, fail_cnt = 0;
+ u32 v, ret, fail_cnt = 0;
for (v = 0; v < VFIFO_SIZE; v++) {
debug_cond(DLEVEL == 2, "%s:%d: vfifo %u\n",
__func__, __LINE__, v);
ret = rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1,
- PASS_ONE_BIT, &bit_chk, 0);
+ PASS_ONE_BIT, 0);
if (!ret) {
fail_cnt++;
u32 *work, const u32 work_inc, u32 *pd)
{
const u32 max = delay ? IO_DQS_EN_DELAY_MAX : IO_DQS_EN_PHASE_MAX;
- u32 ret, bit_chk;
+ u32 ret;
for (; *pd <= max; (*pd)++) {
if (delay)
scc_mgr_set_dqs_en_phase_all_ranks(grp, *pd);
ret = rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1,
- PASS_ONE_BIT, &bit_chk, 0);
+ PASS_ONE_BIT, 0);
if (!working)
ret = !ret;
*/
static void sdr_backup_phase(const u32 grp, u32 *work_bgn, u32 *p)
{
- u32 tmp_delay, bit_chk, d;
+ u32 tmp_delay, d;
int ret;
/* Special case code for backing up a phase */
scc_mgr_set_dqs_en_delay_all_ranks(grp, d);
ret = rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1,
- PASS_ONE_BIT, &bit_chk, 0);
+ PASS_ONE_BIT, 0);
if (ret) {
*work_bgn = tmp_delay;
break;
static int sdr_find_window_center(const u32 grp, const u32 work_bgn,
const u32 work_end)
{
- u32 bit_chk, work_mid;
+ u32 work_mid;
int tmp_delay = 0;
int i, p, d;
debug_cond(DLEVEL == 2, "find_dqs_en_phase: center\n");
if (rw_mgr_mem_calibrate_read_test_all_ranks(grp, 1,
PASS_ONE_BIT,
- &bit_chk, 0)) {
+ 0)) {
debug_cond(DLEVEL == 2,
"%s:%d center: found: ptap=%u dtap=%u\n",
__func__, __LINE__, p, d);
return -EINVAL;
}
-/* find a good dqs enable to use */
-static uint32_t rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(u32 grp)
+/**
+ * rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase() - Find a good DQS enable to use
+ * @grp: Read/Write Group
+ *
+ * Find a good DQS enable to use.
+ */
+static int rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(const u32 grp)
{
- uint32_t d, p, i;
- uint32_t dtaps_per_ptap;
- uint32_t work_bgn, work_end;
- uint32_t found_passing_read, found_failing_read, initial_failing_dtap;
+ u32 d, p, i;
+ u32 dtaps_per_ptap;
+ u32 work_bgn, work_end;
+ u32 found_passing_read, found_failing_read, initial_failing_dtap;
+ int ret;
debug("%s:%d %u\n", __func__, __LINE__, grp);
/* Step 2: Find first working phase, increment in ptaps. */
work_bgn = 0;
- if (sdr_working_phase(grp, &work_bgn, &d, &p, &i))
- return 0;
+ ret = sdr_working_phase(grp, &work_bgn, &d, &p, &i);
+ if (ret)
+ return ret;
work_end = work_bgn;
* Step 4a: go forward from working phase to non working
* phase, increment in ptaps.
*/
- if (sdr_nonworking_phase(grp, &work_end, &p, &i))
- return 0;
+ ret = sdr_nonworking_phase(grp, &work_end, &p, &i);
+ if (ret)
+ return ret;
/* Step 5a: Back off one from last, increment in dtaps. */
/* nil range */
debug_cond(DLEVEL == 2, "%s:%d end-2: failed\n",
__func__, __LINE__);
- return 0;
+ return -EINVAL;
}
debug_cond(DLEVEL == 2, "%s:%d found range [%u,%u]\n",
__func__, __LINE__, d, initial_failing_dtap, dtaps_per_ptap);
/* Step 6: Find the centre of the window. */
- if (sdr_find_window_centre(grp, work_bgn, work_end))
- return 0;
+ ret = sdr_find_window_center(grp, work_bgn, work_end);
- return 1;
+ return ret;
}
-/* per-bit deskew DQ and center */
-static uint32_t rw_mgr_mem_calibrate_vfifo_center(uint32_t rank_bgn,
- uint32_t write_group, uint32_t read_group, uint32_t test_bgn,
- uint32_t use_read_test, uint32_t update_fom)
+/**
+ * search_stop_check() - Check if the detected edge is valid
+ * @write: Perform read (Stage 2) or write (Stage 3) calibration
+ * @d: DQS delay
+ * @rank_bgn: Rank number
+ * @write_group: Write Group
+ * @read_group: Read Group
+ * @bit_chk: Resulting bit mask after the test
+ * @sticky_bit_chk: Resulting sticky bit mask after the test
+ * @use_read_test: Perform read test
+ *
+ * Test if the found edge is valid.
+ */
+static u32 search_stop_check(const int write, const int d, const int rank_bgn,
+ const u32 write_group, const u32 read_group,
+ u32 *bit_chk, u32 *sticky_bit_chk,
+ const u32 use_read_test)
{
- uint32_t i, p, d, min_index;
+ const u32 ratio = RW_MGR_MEM_IF_READ_DQS_WIDTH /
+ RW_MGR_MEM_IF_WRITE_DQS_WIDTH;
+ const u32 correct_mask = write ? param->write_correct_mask :
+ param->read_correct_mask;
+ const u32 per_dqs = write ? RW_MGR_MEM_DQ_PER_WRITE_DQS :
+ RW_MGR_MEM_DQ_PER_READ_DQS;
+ u32 ret;
/*
- * Store these as signed since there are comparisons with
- * signed numbers.
+ * Stop searching when the read test doesn't pass AND when
+ * we've seen a passing read on every bit.
*/
- uint32_t bit_chk;
- uint32_t sticky_bit_chk;
- int32_t left_edge[RW_MGR_MEM_DQ_PER_READ_DQS];
- int32_t right_edge[RW_MGR_MEM_DQ_PER_READ_DQS];
- int32_t final_dq[RW_MGR_MEM_DQ_PER_READ_DQS];
- int32_t mid;
- int32_t orig_mid_min, mid_min;
- int32_t new_dqs, start_dqs, start_dqs_en, shift_dq, final_dqs,
- final_dqs_en;
- int32_t dq_margin, dqs_margin;
- uint32_t stop;
- uint32_t temp_dq_in_delay1, temp_dq_in_delay2;
- uint32_t addr;
+ if (write) { /* WRITE-ONLY */
+ ret = !rw_mgr_mem_calibrate_write_test(rank_bgn, write_group,
+ 0, PASS_ONE_BIT,
+ bit_chk, 0);
+ } else if (use_read_test) { /* READ-ONLY */
+ ret = !rw_mgr_mem_calibrate_read_test(rank_bgn, read_group,
+ NUM_READ_PB_TESTS,
+ PASS_ONE_BIT, bit_chk,
+ 0, 0);
+ } else { /* READ-ONLY */
+ rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 0,
+ PASS_ONE_BIT, bit_chk, 0);
+ *bit_chk = *bit_chk >> (per_dqs *
+ (read_group - (write_group * ratio)));
+ ret = (*bit_chk == 0);
+ }
+ *sticky_bit_chk = *sticky_bit_chk | *bit_chk;
+ ret = ret && (*sticky_bit_chk == correct_mask);
+ debug_cond(DLEVEL == 2,
+ "%s:%d center(left): dtap=%u => %u == %u && %u",
+ __func__, __LINE__, d,
+ *sticky_bit_chk, correct_mask, ret);
+ return ret;
+}
- debug("%s:%d: %u %u", __func__, __LINE__, read_group, test_bgn);
+/**
+ * search_left_edge() - Find left edge of DQ/DQS working phase
+ * @write: Perform read (Stage 2) or write (Stage 3) calibration
+ * @rank_bgn: Rank number
+ * @write_group: Write Group
+ * @read_group: Read Group
+ * @test_bgn: Rank number to begin the test
+ * @sticky_bit_chk: Resulting sticky bit mask after the test
+ * @left_edge: Left edge of the DQ/DQS phase
+ * @right_edge: Right edge of the DQ/DQS phase
+ * @use_read_test: Perform read test
+ *
+ * Find left edge of DQ/DQS working phase.
+ */
+static void search_left_edge(const int write, const int rank_bgn,
+ const u32 write_group, const u32 read_group, const u32 test_bgn,
+ u32 *sticky_bit_chk,
+ int *left_edge, int *right_edge, const u32 use_read_test)
+{
+ const u32 delay_max = write ? IO_IO_OUT1_DELAY_MAX : IO_IO_IN_DELAY_MAX;
+ const u32 dqs_max = write ? IO_IO_OUT1_DELAY_MAX : IO_DQS_IN_DELAY_MAX;
+ const u32 per_dqs = write ? RW_MGR_MEM_DQ_PER_WRITE_DQS :
+ RW_MGR_MEM_DQ_PER_READ_DQS;
+ u32 stop, bit_chk;
+ int i, d;
+
+ for (d = 0; d <= dqs_max; d++) {
+ if (write)
+ scc_mgr_apply_group_dq_out1_delay(d);
+ else
+ scc_mgr_apply_group_dq_in_delay(test_bgn, d);
- addr = SDR_PHYGRP_SCCGRP_ADDRESS | SCC_MGR_DQS_IN_DELAY_OFFSET;
- start_dqs = readl(addr + (read_group << 2));
- if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS)
- start_dqs_en = readl(addr + ((read_group << 2)
- - IO_DQS_EN_DELAY_OFFSET));
+ writel(0, &sdr_scc_mgr->update);
- /* set the left and right edge of each bit to an illegal value */
- /* use (IO_IO_IN_DELAY_MAX + 1) as an illegal value */
- sticky_bit_chk = 0;
- for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
- left_edge[i] = IO_IO_IN_DELAY_MAX + 1;
- right_edge[i] = IO_IO_IN_DELAY_MAX + 1;
+ stop = search_stop_check(write, d, rank_bgn, write_group,
+ read_group, &bit_chk, sticky_bit_chk,
+ use_read_test);
+ if (stop == 1)
+ break;
+
+ /* stop != 1 */
+ for (i = 0; i < per_dqs; i++) {
+ if (bit_chk & 1) {
+ /*
+ * Remember a passing test as
+ * the left_edge.
+ */
+ left_edge[i] = d;
+ } else {
+ /*
+ * If a left edge has not been seen
+ * yet, then a future passing test
+ * will mark this edge as the right
+ * edge.
+ */
+ if (left_edge[i] == delay_max + 1)
+ right_edge[i] = -(d + 1);
+ }
+ bit_chk >>= 1;
+ }
}
- /* Search for the left edge of the window for each bit */
- for (d = 0; d <= IO_IO_IN_DELAY_MAX; d++) {
- scc_mgr_apply_group_dq_in_delay(write_group, test_bgn, d);
+ /* Reset DQ delay chains to 0 */
+ if (write)
+ scc_mgr_apply_group_dq_out1_delay(0);
+ else
+ scc_mgr_apply_group_dq_in_delay(test_bgn, 0);
- writel(0, &sdr_scc_mgr->update);
+ *sticky_bit_chk = 0;
+ for (i = per_dqs - 1; i >= 0; i--) {
+ debug_cond(DLEVEL == 2,
+ "%s:%d vfifo_center: left_edge[%u]: %d right_edge[%u]: %d\n",
+ __func__, __LINE__, i, left_edge[i],
+ i, right_edge[i]);
/*
- * Stop searching when the read test doesn't pass AND when
- * we've seen a passing read on every bit.
+ * Check for cases where we haven't found the left edge,
+ * which makes our assignment of the the right edge invalid.
+ * Reset it to the illegal value.
*/
- if (use_read_test) {
- stop = !rw_mgr_mem_calibrate_read_test(rank_bgn,
- read_group, NUM_READ_PB_TESTS, PASS_ONE_BIT,
- &bit_chk, 0, 0);
- } else {
- rw_mgr_mem_calibrate_write_test(rank_bgn, write_group,
- 0, PASS_ONE_BIT,
- &bit_chk, 0);
- bit_chk = bit_chk >> (RW_MGR_MEM_DQ_PER_READ_DQS *
- (read_group - (write_group *
- RW_MGR_MEM_IF_READ_DQS_WIDTH /
- RW_MGR_MEM_IF_WRITE_DQS_WIDTH)));
- stop = (bit_chk == 0);
- }
- sticky_bit_chk = sticky_bit_chk | bit_chk;
- stop = stop && (sticky_bit_chk == param->read_correct_mask);
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center(left): dtap=%u => %u == %u \
- && %u", __func__, __LINE__, d,
- sticky_bit_chk,
- param->read_correct_mask, stop);
-
- if (stop == 1) {
- break;
- } else {
- for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
- if (bit_chk & 1) {
- /* Remember a passing test as the
- left_edge */
- left_edge[i] = d;
- } else {
- /* If a left edge has not been seen yet,
- then a future passing test will mark
- this edge as the right edge */
- if (left_edge[i] ==
- IO_IO_IN_DELAY_MAX + 1) {
- right_edge[i] = -(d + 1);
- }
- }
- bit_chk = bit_chk >> 1;
- }
- }
- }
-
- /* Reset DQ delay chains to 0 */
- scc_mgr_apply_group_dq_in_delay(test_bgn, 0);
- sticky_bit_chk = 0;
- for (i = RW_MGR_MEM_DQ_PER_READ_DQS - 1;; i--) {
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center: left_edge[%u]: \
- %d right_edge[%u]: %d\n", __func__, __LINE__,
- i, left_edge[i], i, right_edge[i]);
-
- /*
- * Check for cases where we haven't found the left edge,
- * which makes our assignment of the the right edge invalid.
- * Reset it to the illegal value.
- */
- if ((left_edge[i] == IO_IO_IN_DELAY_MAX + 1) && (
- right_edge[i] != IO_IO_IN_DELAY_MAX + 1)) {
- right_edge[i] = IO_IO_IN_DELAY_MAX + 1;
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center: reset \
- right_edge[%u]: %d\n", __func__, __LINE__,
- i, right_edge[i]);
+ if ((left_edge[i] == delay_max + 1) &&
+ (right_edge[i] != delay_max + 1)) {
+ right_edge[i] = delay_max + 1;
+ debug_cond(DLEVEL == 2,
+ "%s:%d vfifo_center: reset right_edge[%u]: %d\n",
+ __func__, __LINE__, i, right_edge[i]);
}
/*
- * Reset sticky bit (except for bits where we have seen
- * both the left and right edge).
+ * Reset sticky bit
+ * READ: except for bits where we have seen both
+ * the left and right edge.
+ * WRITE: except for bits where we have seen the
+ * left edge.
*/
- sticky_bit_chk = sticky_bit_chk << 1;
- if ((left_edge[i] != IO_IO_IN_DELAY_MAX + 1) &&
- (right_edge[i] != IO_IO_IN_DELAY_MAX + 1)) {
- sticky_bit_chk = sticky_bit_chk | 1;
+ *sticky_bit_chk <<= 1;
+ if (write) {
+ if (left_edge[i] != delay_max + 1)
+ *sticky_bit_chk |= 1;
+ } else {
+ if ((left_edge[i] != delay_max + 1) &&
+ (right_edge[i] != delay_max + 1))
+ *sticky_bit_chk |= 1;
}
-
- if (i == 0)
- break;
}
- /* Search for the right edge of the window for each bit */
- for (d = 0; d <= IO_DQS_IN_DELAY_MAX - start_dqs; d++) {
- scc_mgr_set_dqs_bus_in_delay(read_group, d + start_dqs);
- if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) {
- uint32_t delay = d + start_dqs_en;
- if (delay > IO_DQS_EN_DELAY_MAX)
- delay = IO_DQS_EN_DELAY_MAX;
- scc_mgr_set_dqs_en_delay(read_group, delay);
- }
- scc_mgr_load_dqs(read_group);
- writel(0, &sdr_scc_mgr->update);
+}
- /*
- * Stop searching when the read test doesn't pass AND when
- * we've seen a passing read on every bit.
- */
- if (use_read_test) {
- stop = !rw_mgr_mem_calibrate_read_test(rank_bgn,
- read_group, NUM_READ_PB_TESTS, PASS_ONE_BIT,
- &bit_chk, 0, 0);
- } else {
- rw_mgr_mem_calibrate_write_test(rank_bgn, write_group,
- 0, PASS_ONE_BIT,
- &bit_chk, 0);
- bit_chk = bit_chk >> (RW_MGR_MEM_DQ_PER_READ_DQS *
- (read_group - (write_group *
- RW_MGR_MEM_IF_READ_DQS_WIDTH /
- RW_MGR_MEM_IF_WRITE_DQS_WIDTH)));
- stop = (bit_chk == 0);
+/**
+ * search_right_edge() - Find right edge of DQ/DQS working phase
+ * @write: Perform read (Stage 2) or write (Stage 3) calibration
+ * @rank_bgn: Rank number
+ * @write_group: Write Group
+ * @read_group: Read Group
+ * @start_dqs: DQS start phase
+ * @start_dqs_en: DQS enable start phase
+ * @sticky_bit_chk: Resulting sticky bit mask after the test
+ * @left_edge: Left edge of the DQ/DQS phase
+ * @right_edge: Right edge of the DQ/DQS phase
+ * @use_read_test: Perform read test
+ *
+ * Find right edge of DQ/DQS working phase.
+ */
+static int search_right_edge(const int write, const int rank_bgn,
+ const u32 write_group, const u32 read_group,
+ const int start_dqs, const int start_dqs_en,
+ u32 *sticky_bit_chk,
+ int *left_edge, int *right_edge, const u32 use_read_test)
+{
+ const u32 delay_max = write ? IO_IO_OUT1_DELAY_MAX : IO_IO_IN_DELAY_MAX;
+ const u32 dqs_max = write ? IO_IO_OUT1_DELAY_MAX : IO_DQS_IN_DELAY_MAX;
+ const u32 per_dqs = write ? RW_MGR_MEM_DQ_PER_WRITE_DQS :
+ RW_MGR_MEM_DQ_PER_READ_DQS;
+ u32 stop, bit_chk;
+ int i, d;
+
+ for (d = 0; d <= dqs_max - start_dqs; d++) {
+ if (write) { /* WRITE-ONLY */
+ scc_mgr_apply_group_dqs_io_and_oct_out1(write_group,
+ d + start_dqs);
+ } else { /* READ-ONLY */
+ scc_mgr_set_dqs_bus_in_delay(read_group, d + start_dqs);
+ if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) {
+ uint32_t delay = d + start_dqs_en;
+ if (delay > IO_DQS_EN_DELAY_MAX)
+ delay = IO_DQS_EN_DELAY_MAX;
+ scc_mgr_set_dqs_en_delay(read_group, delay);
+ }
+ scc_mgr_load_dqs(read_group);
}
- sticky_bit_chk = sticky_bit_chk | bit_chk;
- stop = stop && (sticky_bit_chk == param->read_correct_mask);
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center(right): dtap=%u => %u == \
- %u && %u", __func__, __LINE__, d,
- sticky_bit_chk, param->read_correct_mask, stop);
+ writel(0, &sdr_scc_mgr->update);
+ stop = search_stop_check(write, d, rank_bgn, write_group,
+ read_group, &bit_chk, sticky_bit_chk,
+ use_read_test);
if (stop == 1) {
+ if (write && (d == 0)) { /* WRITE-ONLY */
+ for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
+ /*
+ * d = 0 failed, but it passed when
+ * testing the left edge, so it must be
+ * marginal, set it to -1
+ */
+ if (right_edge[i] == delay_max + 1 &&
+ left_edge[i] != delay_max + 1)
+ right_edge[i] = -1;
+ }
+ }
break;
- } else {
- for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
- if (bit_chk & 1) {
- /* Remember a passing test as
- the right_edge */
- right_edge[i] = d;
+ }
+
+ /* stop != 1 */
+ for (i = 0; i < per_dqs; i++) {
+ if (bit_chk & 1) {
+ /*
+ * Remember a passing test as
+ * the right_edge.
+ */
+ right_edge[i] = d;
+ } else {
+ if (d != 0) {
+ /*
+ * If a right edge has not
+ * been seen yet, then a future
+ * passing test will mark this
+ * edge as the left edge.
+ */
+ if (right_edge[i] == delay_max + 1)
+ left_edge[i] = -(d + 1);
} else {
- if (d != 0) {
- /* If a right edge has not been
- seen yet, then a future passing
- test will mark this edge as the
- left edge */
- if (right_edge[i] ==
- IO_IO_IN_DELAY_MAX + 1) {
- left_edge[i] = -(d + 1);
- }
- } else {
- /* d = 0 failed, but it passed
- when testing the left edge,
- so it must be marginal,
- set it to -1 */
- if (right_edge[i] ==
- IO_IO_IN_DELAY_MAX + 1 &&
- left_edge[i] !=
- IO_IO_IN_DELAY_MAX
- + 1) {
- right_edge[i] = -1;
- }
- /* If a right edge has not been
- seen yet, then a future passing
- test will mark this edge as the
- left edge */
- else if (right_edge[i] ==
- IO_IO_IN_DELAY_MAX +
- 1) {
- left_edge[i] = -(d + 1);
- }
- }
+ /*
+ * d = 0 failed, but it passed
+ * when testing the left edge,
+ * so it must be marginal, set
+ * it to -1
+ */
+ if (right_edge[i] == delay_max + 1 &&
+ left_edge[i] != delay_max + 1)
+ right_edge[i] = -1;
+ /*
+ * If a right edge has not been
+ * seen yet, then a future
+ * passing test will mark this
+ * edge as the left edge.
+ */
+ else if (right_edge[i] == delay_max + 1)
+ left_edge[i] = -(d + 1);
}
-
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center[r,\
- d=%u]: ", __func__, __LINE__, d);
- debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d ",
- (int)(bit_chk & 1), i, left_edge[i]);
- debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i,
- right_edge[i]);
- bit_chk = bit_chk >> 1;
}
+
+ debug_cond(DLEVEL == 2, "%s:%d center[r,d=%u]: ",
+ __func__, __LINE__, d);
+ debug_cond(DLEVEL == 2,
+ "bit_chk_test=%i left_edge[%u]: %d ",
+ bit_chk & 1, i, left_edge[i]);
+ debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i,
+ right_edge[i]);
+ bit_chk >>= 1;
}
}
/* Check that all bits have a window */
- for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center: left_edge[%u]: \
- %d right_edge[%u]: %d", __func__, __LINE__,
- i, left_edge[i], i, right_edge[i]);
- if ((left_edge[i] == IO_IO_IN_DELAY_MAX + 1) || (right_edge[i]
- == IO_IO_IN_DELAY_MAX + 1)) {
- /*
- * Restore delay chain settings before letting the loop
- * in rw_mgr_mem_calibrate_vfifo to retry different
- * dqs/ck relationships.
- */
- scc_mgr_set_dqs_bus_in_delay(read_group, start_dqs);
- if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) {
- scc_mgr_set_dqs_en_delay(read_group,
- start_dqs_en);
- }
- scc_mgr_load_dqs(read_group);
- writel(0, &sdr_scc_mgr->update);
-
- debug_cond(DLEVEL == 1, "%s:%d vfifo_center: failed to \
- find edge [%u]: %d %d", __func__, __LINE__,
- i, left_edge[i], right_edge[i]);
- if (use_read_test) {
- set_failing_group_stage(read_group *
- RW_MGR_MEM_DQ_PER_READ_DQS + i,
- CAL_STAGE_VFIFO,
- CAL_SUBSTAGE_VFIFO_CENTER);
- } else {
- set_failing_group_stage(read_group *
- RW_MGR_MEM_DQ_PER_READ_DQS + i,
- CAL_STAGE_VFIFO_AFTER_WRITES,
- CAL_SUBSTAGE_VFIFO_CENTER);
- }
- return 0;
- }
+ for (i = 0; i < per_dqs; i++) {
+ debug_cond(DLEVEL == 2,
+ "%s:%d write_center: left_edge[%u]: %d right_edge[%u]: %d",
+ __func__, __LINE__, i, left_edge[i],
+ i, right_edge[i]);
+ if ((left_edge[i] == dqs_max + 1) ||
+ (right_edge[i] == dqs_max + 1))
+ return i + 1; /* FIXME: If we fail, retval > 0 */
}
+ return 0;
+}
+
+/**
+ * get_window_mid_index() - Find the best middle setting of DQ/DQS phase
+ * @write: Perform read (Stage 2) or write (Stage 3) calibration
+ * @left_edge: Left edge of the DQ/DQS phase
+ * @right_edge: Right edge of the DQ/DQS phase
+ * @mid_min: Best DQ/DQS phase middle setting
+ *
+ * Find index and value of the middle of the DQ/DQS working phase.
+ */
+static int get_window_mid_index(const int write, int *left_edge,
+ int *right_edge, int *mid_min)
+{
+ const u32 per_dqs = write ? RW_MGR_MEM_DQ_PER_WRITE_DQS :
+ RW_MGR_MEM_DQ_PER_READ_DQS;
+ int i, mid, min_index;
+
/* Find middle of window for each DQ bit */
- mid_min = left_edge[0] - right_edge[0];
+ *mid_min = left_edge[0] - right_edge[0];
min_index = 0;
- for (i = 1; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
+ for (i = 1; i < per_dqs; i++) {
mid = left_edge[i] - right_edge[i];
- if (mid < mid_min) {
- mid_min = mid;
+ if (mid < *mid_min) {
+ *mid_min = mid;
min_index = i;
}
}
/*
* -mid_min/2 represents the amount that we need to move DQS.
- * If mid_min is odd and positive we'll need to add one to
- * make sure the rounding in further calculations is correct
- * (always bias to the right), so just add 1 for all positive values.
+ * If mid_min is odd and positive we'll need to add one to make
+ * sure the rounding in further calculations is correct (always
+ * bias to the right), so just add 1 for all positive values.
+ */
+ if (*mid_min > 0)
+ (*mid_min)++;
+ *mid_min = *mid_min / 2;
+
+ debug_cond(DLEVEL == 1, "%s:%d vfifo_center: *mid_min=%d (index=%u)\n",
+ __func__, __LINE__, *mid_min, min_index);
+ return min_index;
+}
+
+/**
+ * center_dq_windows() - Center the DQ/DQS windows
+ * @write: Perform read (Stage 2) or write (Stage 3) calibration
+ * @left_edge: Left edge of the DQ/DQS phase
+ * @right_edge: Right edge of the DQ/DQS phase
+ * @mid_min: Adjusted DQ/DQS phase middle setting
+ * @orig_mid_min: Original DQ/DQS phase middle setting
+ * @min_index: DQ/DQS phase middle setting index
+ * @test_bgn: Rank number to begin the test
+ * @dq_margin: Amount of shift for the DQ
+ * @dqs_margin: Amount of shift for the DQS
+ *
+ * Align the DQ/DQS windows in each group.
+ */
+static void center_dq_windows(const int write, int *left_edge, int *right_edge,
+ const int mid_min, const int orig_mid_min,
+ const int min_index, const int test_bgn,
+ int *dq_margin, int *dqs_margin)
+{
+ const u32 delay_max = write ? IO_IO_OUT1_DELAY_MAX : IO_IO_IN_DELAY_MAX;
+ const u32 per_dqs = write ? RW_MGR_MEM_DQ_PER_WRITE_DQS :
+ RW_MGR_MEM_DQ_PER_READ_DQS;
+ const u32 delay_off = write ? SCC_MGR_IO_OUT1_DELAY_OFFSET :
+ SCC_MGR_IO_IN_DELAY_OFFSET;
+ const u32 addr = SDR_PHYGRP_SCCGRP_ADDRESS | delay_off;
+
+ u32 temp_dq_io_delay1, temp_dq_io_delay2;
+ int shift_dq, i, p;
+
+ /* Initialize data for export structures */
+ *dqs_margin = delay_max + 1;
+ *dq_margin = delay_max + 1;
+
+ /* add delay to bring centre of all DQ windows to the same "level" */
+ for (i = 0, p = test_bgn; i < per_dqs; i++, p++) {
+ /* Use values before divide by 2 to reduce round off error */
+ shift_dq = (left_edge[i] - right_edge[i] -
+ (left_edge[min_index] - right_edge[min_index]))/2 +
+ (orig_mid_min - mid_min);
+
+ debug_cond(DLEVEL == 2,
+ "vfifo_center: before: shift_dq[%u]=%d\n",
+ i, shift_dq);
+
+ temp_dq_io_delay1 = readl(addr + (p << 2));
+ temp_dq_io_delay2 = readl(addr + (i << 2));
+
+ if (shift_dq + temp_dq_io_delay1 > delay_max)
+ shift_dq = delay_max - temp_dq_io_delay2;
+ else if (shift_dq + temp_dq_io_delay1 < 0)
+ shift_dq = -temp_dq_io_delay1;
+
+ debug_cond(DLEVEL == 2,
+ "vfifo_center: after: shift_dq[%u]=%d\n",
+ i, shift_dq);
+
+ if (write)
+ scc_mgr_set_dq_out1_delay(i, temp_dq_io_delay1 + shift_dq);
+ else
+ scc_mgr_set_dq_in_delay(p, temp_dq_io_delay1 + shift_dq);
+
+ scc_mgr_load_dq(p);
+
+ debug_cond(DLEVEL == 2,
+ "vfifo_center: margin[%u]=[%d,%d]\n", i,
+ left_edge[i] - shift_dq + (-mid_min),
+ right_edge[i] + shift_dq - (-mid_min));
+
+ /* To determine values for export structures */
+ if (left_edge[i] - shift_dq + (-mid_min) < *dq_margin)
+ *dq_margin = left_edge[i] - shift_dq + (-mid_min);
+
+ if (right_edge[i] + shift_dq - (-mid_min) < *dqs_margin)
+ *dqs_margin = right_edge[i] + shift_dq - (-mid_min);
+ }
+
+}
+
+/**
+ * rw_mgr_mem_calibrate_vfifo_center() - Per-bit deskew DQ and centering
+ * @rank_bgn: Rank number
+ * @rw_group: Read/Write Group
+ * @test_bgn: Rank at which the test begins
+ * @use_read_test: Perform a read test
+ * @update_fom: Update FOM
+ *
+ * Per-bit deskew DQ and centering.
+ */
+static int rw_mgr_mem_calibrate_vfifo_center(const u32 rank_bgn,
+ const u32 rw_group, const u32 test_bgn,
+ const int use_read_test, const int update_fom)
+{
+ const u32 addr =
+ SDR_PHYGRP_SCCGRP_ADDRESS + SCC_MGR_DQS_IN_DELAY_OFFSET +
+ (rw_group << 2);
+ /*
+ * Store these as signed since there are comparisons with
+ * signed numbers.
*/
- if (mid_min > 0)
- mid_min++;
+ uint32_t sticky_bit_chk;
+ int32_t left_edge[RW_MGR_MEM_DQ_PER_READ_DQS];
+ int32_t right_edge[RW_MGR_MEM_DQ_PER_READ_DQS];
+ int32_t orig_mid_min, mid_min;
+ int32_t new_dqs, start_dqs, start_dqs_en, final_dqs_en;
+ int32_t dq_margin, dqs_margin;
+ int i, min_index;
+ int ret;
+
+ debug("%s:%d: %u %u", __func__, __LINE__, rw_group, test_bgn);
+
+ start_dqs = readl(addr);
+ if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS)
+ start_dqs_en = readl(addr - IO_DQS_EN_DELAY_OFFSET);
+
+ /* set the left and right edge of each bit to an illegal value */
+ /* use (IO_IO_IN_DELAY_MAX + 1) as an illegal value */
+ sticky_bit_chk = 0;
+ for (i = 0; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++) {
+ left_edge[i] = IO_IO_IN_DELAY_MAX + 1;
+ right_edge[i] = IO_IO_IN_DELAY_MAX + 1;
+ }
+
+ /* Search for the left edge of the window for each bit */
+ search_left_edge(0, rank_bgn, rw_group, rw_group, test_bgn,
+ &sticky_bit_chk,
+ left_edge, right_edge, use_read_test);
+
+
+ /* Search for the right edge of the window for each bit */
+ ret = search_right_edge(0, rank_bgn, rw_group, rw_group,
+ start_dqs, start_dqs_en,
+ &sticky_bit_chk,
+ left_edge, right_edge, use_read_test);
+ if (ret) {
+ /*
+ * Restore delay chain settings before letting the loop
+ * in rw_mgr_mem_calibrate_vfifo to retry different
+ * dqs/ck relationships.
+ */
+ scc_mgr_set_dqs_bus_in_delay(rw_group, start_dqs);
+ if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS)
+ scc_mgr_set_dqs_en_delay(rw_group, start_dqs_en);
- mid_min = mid_min / 2;
+ scc_mgr_load_dqs(rw_group);
+ writel(0, &sdr_scc_mgr->update);
+
+ debug_cond(DLEVEL == 1,
+ "%s:%d vfifo_center: failed to find edge [%u]: %d %d",
+ __func__, __LINE__, i, left_edge[i], right_edge[i]);
+ if (use_read_test) {
+ set_failing_group_stage(rw_group *
+ RW_MGR_MEM_DQ_PER_READ_DQS + i,
+ CAL_STAGE_VFIFO,
+ CAL_SUBSTAGE_VFIFO_CENTER);
+ } else {
+ set_failing_group_stage(rw_group *
+ RW_MGR_MEM_DQ_PER_READ_DQS + i,
+ CAL_STAGE_VFIFO_AFTER_WRITES,
+ CAL_SUBSTAGE_VFIFO_CENTER);
+ }
+ return -EIO;
+ }
- debug_cond(DLEVEL == 1, "%s:%d vfifo_center: mid_min=%d (index=%u)\n",
- __func__, __LINE__, mid_min, min_index);
+ min_index = get_window_mid_index(0, left_edge, right_edge, &mid_min);
/* Determine the amount we can change DQS (which is -mid_min) */
orig_mid_min = mid_min;
}
new_dqs = start_dqs - mid_min;
- debug_cond(DLEVEL == 1, "vfifo_center: start_dqs=%d start_dqs_en=%d \
- new_dqs=%d mid_min=%d\n", start_dqs,
+ debug_cond(DLEVEL == 1,
+ "vfifo_center: start_dqs=%d start_dqs_en=%d new_dqs=%d mid_min=%d\n",
+ start_dqs,
IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS ? start_dqs_en : -1,
new_dqs, mid_min);
- /* Initialize data for export structures */
- dqs_margin = IO_IO_IN_DELAY_MAX + 1;
- dq_margin = IO_IO_IN_DELAY_MAX + 1;
-
- /* add delay to bring centre of all DQ windows to the same "level" */
- for (i = 0, p = test_bgn; i < RW_MGR_MEM_DQ_PER_READ_DQS; i++, p++) {
- /* Use values before divide by 2 to reduce round off error */
- shift_dq = (left_edge[i] - right_edge[i] -
- (left_edge[min_index] - right_edge[min_index]))/2 +
- (orig_mid_min - mid_min);
-
- debug_cond(DLEVEL == 2, "vfifo_center: before: \
- shift_dq[%u]=%d\n", i, shift_dq);
-
- addr = SDR_PHYGRP_SCCGRP_ADDRESS | SCC_MGR_IO_IN_DELAY_OFFSET;
- temp_dq_in_delay1 = readl(addr + (p << 2));
- temp_dq_in_delay2 = readl(addr + (i << 2));
-
- if (shift_dq + (int32_t)temp_dq_in_delay1 >
- (int32_t)IO_IO_IN_DELAY_MAX) {
- shift_dq = (int32_t)IO_IO_IN_DELAY_MAX - temp_dq_in_delay2;
- } else if (shift_dq + (int32_t)temp_dq_in_delay1 < 0) {
- shift_dq = -(int32_t)temp_dq_in_delay1;
- }
- debug_cond(DLEVEL == 2, "vfifo_center: after: \
- shift_dq[%u]=%d\n", i, shift_dq);
- final_dq[i] = temp_dq_in_delay1 + shift_dq;
- scc_mgr_set_dq_in_delay(p, final_dq[i]);
- scc_mgr_load_dq(p);
-
- debug_cond(DLEVEL == 2, "vfifo_center: margin[%u]=[%d,%d]\n", i,
- left_edge[i] - shift_dq + (-mid_min),
- right_edge[i] + shift_dq - (-mid_min));
- /* To determine values for export structures */
- if (left_edge[i] - shift_dq + (-mid_min) < dq_margin)
- dq_margin = left_edge[i] - shift_dq + (-mid_min);
-
- if (right_edge[i] + shift_dq - (-mid_min) < dqs_margin)
- dqs_margin = right_edge[i] + shift_dq - (-mid_min);
- }
-
- final_dqs = new_dqs;
- if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS)
- final_dqs_en = start_dqs_en - mid_min;
+ /* Add delay to bring centre of all DQ windows to the same "level". */
+ center_dq_windows(0, left_edge, right_edge, mid_min, orig_mid_min,
+ min_index, test_bgn, &dq_margin, &dqs_margin);
/* Move DQS-en */
if (IO_SHIFT_DQS_EN_WHEN_SHIFT_DQS) {
- scc_mgr_set_dqs_en_delay(read_group, final_dqs_en);
- scc_mgr_load_dqs(read_group);
+ final_dqs_en = start_dqs_en - mid_min;
+ scc_mgr_set_dqs_en_delay(rw_group, final_dqs_en);
+ scc_mgr_load_dqs(rw_group);
}
/* Move DQS */
- scc_mgr_set_dqs_bus_in_delay(read_group, final_dqs);
- scc_mgr_load_dqs(read_group);
- debug_cond(DLEVEL == 2, "%s:%d vfifo_center: dq_margin=%d \
- dqs_margin=%d", __func__, __LINE__,
- dq_margin, dqs_margin);
+ scc_mgr_set_dqs_bus_in_delay(rw_group, new_dqs);
+ scc_mgr_load_dqs(rw_group);
+ debug_cond(DLEVEL == 2,
+ "%s:%d vfifo_center: dq_margin=%d dqs_margin=%d",
+ __func__, __LINE__, dq_margin, dqs_margin);
/*
* Do not remove this line as it makes sure all of our decisions
*/
writel(0, &sdr_scc_mgr->update);
- return (dq_margin >= 0) && (dqs_margin >= 0);
+ if ((dq_margin < 0) || (dqs_margin < 0))
+ return -EINVAL;
+
+ return 0;
}
/**
/* We start at zero, so have one less dq to devide among */
const u32 delay_step = IO_IO_IN_DELAY_MAX /
(RW_MGR_MEM_DQ_PER_READ_DQS - 1);
- int found;
+ int ret;
u32 i, p, d, r;
debug("%s:%d (%u,%u)\n", __func__, __LINE__, rw_group, test_bgn);
* Try rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase across different
* dq_in_delay values
*/
- found = rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(rw_group);
+ ret = rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase(rw_group);
debug_cond(DLEVEL == 1,
"%s:%d: g=%u found=%u; Reseting delay chain to zero\n",
- __func__, __LINE__, rw_group, found);
+ __func__, __LINE__, rw_group, !ret);
for (r = 0; r < RW_MGR_MEM_NUMBER_OF_RANKS;
r += NUM_RANKS_PER_SHADOW_REG) {
writel(0, &sdr_scc_mgr->update);
}
- if (!found)
- return -EINVAL;
-
- return 0;
-
+ return ret;
}
/**
continue;
ret = rw_mgr_mem_calibrate_vfifo_center(rank_bgn, rw_group,
- rw_group, test_bgn,
+ test_bgn,
use_read_test,
update_fom);
- if (ret)
+ if (!ret)
continue;
grp_calibrated = 0;
return 1;
}
-/* VFIFO Calibration -- Read Deskew Calibration after write deskew */
-static uint32_t rw_mgr_mem_calibrate_vfifo_end(uint32_t read_group,
- uint32_t test_bgn)
+/**
+ * rw_mgr_mem_calibrate_vfifo_end() - DQ/DQS Centering.
+ * @rw_group: Read/Write Group
+ * @test_bgn: Rank at which the test begins
+ *
+ * Stage 3: DQ/DQS Centering.
+ *
+ * This function implements UniPHY calibration Stage 3, as explained in
+ * detail in Altera EMI_RM 2015.05.04 , "UniPHY Calibration Stages".
+ */
+static int rw_mgr_mem_calibrate_vfifo_end(const u32 rw_group,
+ const u32 test_bgn)
{
- uint32_t rank_bgn, sr;
- uint32_t grp_calibrated;
- uint32_t write_group;
-
- debug("%s:%d %u %u", __func__, __LINE__, read_group, test_bgn);
+ int ret;
- /* update info for sims */
+ debug("%s:%d %u %u", __func__, __LINE__, rw_group, test_bgn);
+ /* Update info for sims. */
+ reg_file_set_group(rw_group);
reg_file_set_stage(CAL_STAGE_VFIFO_AFTER_WRITES);
reg_file_set_sub_stage(CAL_SUBSTAGE_VFIFO_CENTER);
- write_group = read_group;
-
- /* update info for sims */
- reg_file_set_group(read_group);
-
- grp_calibrated = 1;
- /* Read per-bit deskew can be done on a per shadow register basis */
- for (rank_bgn = 0, sr = 0; rank_bgn < RW_MGR_MEM_NUMBER_OF_RANKS;
- rank_bgn += NUM_RANKS_PER_SHADOW_REG, ++sr) {
- /* Determine if this set of ranks should be skipped entirely */
- if (!param->skip_shadow_regs[sr]) {
- /* This is the last calibration round, update FOM here */
- if (!rw_mgr_mem_calibrate_vfifo_center(rank_bgn,
- write_group,
- read_group,
- test_bgn, 0,
- 1)) {
- grp_calibrated = 0;
- }
- }
- }
-
-
- if (grp_calibrated == 0) {
- set_failing_group_stage(write_group,
+ ret = rw_mgr_mem_calibrate_dq_dqs_centering(rw_group, test_bgn, 0, 1);
+ if (ret)
+ set_failing_group_stage(rw_group,
CAL_STAGE_VFIFO_AFTER_WRITES,
CAL_SUBSTAGE_VFIFO_CENTER);
- return 0;
- }
-
- return 1;
+ return ret;
}
-/* Calibrate LFIFO to find smallest read latency */
+/**
+ * rw_mgr_mem_calibrate_lfifo() - Minimize latency
+ *
+ * Stage 4: Minimize latency.
+ *
+ * This function implements UniPHY calibration Stage 4, as explained in
+ * detail in Altera EMI_RM 2015.05.04 , "UniPHY Calibration Stages".
+ * Calibrate LFIFO to find smallest read latency.
+ */
static uint32_t rw_mgr_mem_calibrate_lfifo(void)
{
- uint32_t found_one;
- uint32_t bit_chk;
+ int found_one = 0;
debug("%s:%d\n", __func__, __LINE__);
- /* update info for sims */
+ /* Update info for sims. */
reg_file_set_stage(CAL_STAGE_LFIFO);
reg_file_set_sub_stage(CAL_SUBSTAGE_READ_LATENCY);
/* Load up the patterns used by read calibration for all ranks */
rw_mgr_mem_calibrate_read_load_patterns(0, 1);
- found_one = 0;
do {
writel(gbl->curr_read_lat, &phy_mgr_cfg->phy_rlat);
debug_cond(DLEVEL == 2, "%s:%d lfifo: read_lat=%u",
__func__, __LINE__, gbl->curr_read_lat);
- if (!rw_mgr_mem_calibrate_read_test_all_ranks(0,
- NUM_READ_TESTS,
- PASS_ALL_BITS,
- &bit_chk, 1)) {
+ if (!rw_mgr_mem_calibrate_read_test_all_ranks(0, NUM_READ_TESTS,
+ PASS_ALL_BITS, 1))
break;
- }
found_one = 1;
- /* reduce read latency and see if things are working */
- /* correctly */
+ /*
+ * Reduce read latency and see if things are
+ * working correctly.
+ */
gbl->curr_read_lat--;
} while (gbl->curr_read_lat > 0);
- /* reset the fifos to get pointers to known state */
-
+ /* Reset the fifos to get pointers to known state. */
writel(0, &phy_mgr_cmd->fifo_reset);
if (found_one) {
- /* add a fudge factor to the read latency that was determined */
+ /* Add a fudge factor to the read latency that was determined */
gbl->curr_read_lat += 2;
writel(gbl->curr_read_lat, &phy_mgr_cfg->phy_rlat);
- debug_cond(DLEVEL == 2, "%s:%d lfifo: success: using \
- read_lat=%u\n", __func__, __LINE__,
- gbl->curr_read_lat);
- return 1;
+ debug_cond(DLEVEL == 2,
+ "%s:%d lfifo: success: using read_lat=%u\n",
+ __func__, __LINE__, gbl->curr_read_lat);
} else {
set_failing_group_stage(0xff, CAL_STAGE_LFIFO,
CAL_SUBSTAGE_READ_LATENCY);
- debug_cond(DLEVEL == 2, "%s:%d lfifo: failed at initial \
- read_lat=%u\n", __func__, __LINE__,
- gbl->curr_read_lat);
- return 0;
+ debug_cond(DLEVEL == 2,
+ "%s:%d lfifo: failed at initial read_lat=%u\n",
+ __func__, __LINE__, gbl->curr_read_lat);
}
+
+ return found_one;
}
-/*
- * issue write test command.
- * two variants are provided. one that just tests a write pattern and
- * another that tests datamask functionality.
+/**
+ * search_window() - Search for the/part of the window with DM/DQS shift
+ * @search_dm: If 1, search for the DM shift, if 0, search for DQS shift
+ * @rank_bgn: Rank number
+ * @write_group: Write Group
+ * @bgn_curr: Current window begin
+ * @end_curr: Current window end
+ * @bgn_best: Current best window begin
+ * @end_best: Current best window end
+ * @win_best: Size of the best window
+ * @new_dqs: New DQS value (only applicable if search_dm = 0).
+ *
+ * Search for the/part of the window with DM/DQS shift.
*/
-static void rw_mgr_mem_calibrate_write_test_issue(uint32_t group,
- uint32_t test_dm)
-{
- uint32_t mcc_instruction;
- uint32_t quick_write_mode = (((STATIC_CALIB_STEPS) & CALIB_SKIP_WRITES) &&
- ENABLE_SUPER_QUICK_CALIBRATION);
- uint32_t rw_wl_nop_cycles;
- uint32_t addr;
+static void search_window(const int search_dm,
+ const u32 rank_bgn, const u32 write_group,
+ int *bgn_curr, int *end_curr, int *bgn_best,
+ int *end_best, int *win_best, int new_dqs)
+{
+ u32 bit_chk;
+ const int max = IO_IO_OUT1_DELAY_MAX - new_dqs;
+ int d, di;
+
+ /* Search for the/part of the window with DM/DQS shift. */
+ for (di = max; di >= 0; di -= DELTA_D) {
+ if (search_dm) {
+ d = di;
+ scc_mgr_apply_group_dm_out1_delay(d);
+ } else {
+ /* For DQS, we go from 0...max */
+ d = max - di;
+ /*
+ * Note: This only shifts DQS, so are we limiting ourselve to
+ * width of DQ unnecessarily.
+ */
+ scc_mgr_apply_group_dqs_io_and_oct_out1(write_group,
+ d + new_dqs);
+ }
- /*
- * Set counter and jump addresses for the right
- * number of NOP cycles.
- * The number of supported NOP cycles can range from -1 to infinity
- * Three different cases are handled:
- *
- * 1. For a number of NOP cycles greater than 0, the RW Mgr looping
- * mechanism will be used to insert the right number of NOPs
- *
- * 2. For a number of NOP cycles equals to 0, the micro-instruction
- * issuing the write command will jump straight to the
- * micro-instruction that turns on DQS (for DDRx), or outputs write
- * data (for RLD), skipping
- * the NOP micro-instruction all together
- *
- * 3. A number of NOP cycles equal to -1 indicates that DQS must be
- * turned on in the same micro-instruction that issues the write
- * command. Then we need
- * to directly jump to the micro-instruction that sends out the data
- *
- * NOTE: Implementing this mechanism uses 2 RW Mgr jump-counters
- * (2 and 3). One jump-counter (0) is used to perform multiple
- * write-read operations.
- * one counter left to issue this command in "multiple-group" mode
- */
-
- rw_wl_nop_cycles = gbl->rw_wl_nop_cycles;
-
- if (rw_wl_nop_cycles == -1) {
- /*
- * CNTR 2 - We want to execute the special write operation that
- * turns on DQS right away and then skip directly to the
- * instruction that sends out the data. We set the counter to a
- * large number so that the jump is always taken.
- */
- writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+ writel(0, &sdr_scc_mgr->update);
- /* CNTR 3 - Not used */
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0_WL_1;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DATA,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- } else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0_WL_1;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_DATA,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- }
- } else if (rw_wl_nop_cycles == 0) {
- /*
- * CNTR 2 - We want to skip the NOP operation and go straight
- * to the DQS enable instruction. We set the counter to a large
- * number so that the jump is always taken.
- */
- writel(0xFF, &sdr_rw_load_mgr_regs->load_cntr2);
+ if (rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 1,
+ PASS_ALL_BITS, &bit_chk,
+ 0)) {
+ /* Set current end of the window. */
+ *end_curr = search_dm ? -d : d;
- /* CNTR 3 - Not used */
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_DQS,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- } else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_DQS,
- &sdr_rw_load_jump_mgr_regs->load_jump_add2);
- }
- } else {
- /*
- * CNTR 2 - In this case we want to execute the next instruction
- * and NOT take the jump. So we set the counter to 0. The jump
- * address doesn't count.
- */
- writel(0x0, &sdr_rw_load_mgr_regs->load_cntr2);
- writel(0x0, &sdr_rw_load_jump_mgr_regs->load_jump_add2);
+ /*
+ * If a starting edge of our window has not been seen
+ * this is our current start of the DM window.
+ */
+ if (*bgn_curr == IO_IO_OUT1_DELAY_MAX + 1)
+ *bgn_curr = search_dm ? -d : d;
- /*
- * CNTR 3 - Set the nop counter to the number of cycles we
- * need to loop for, minus 1.
- */
- writel(rw_wl_nop_cycles - 1, &sdr_rw_load_mgr_regs->load_cntr3);
- if (test_dm) {
- mcc_instruction = RW_MGR_LFSR_WR_RD_DM_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
+ /*
+ * If current window is bigger than best seen.
+ * Set best seen to be current window.
+ */
+ if ((*end_curr - *bgn_curr + 1) > *win_best) {
+ *win_best = *end_curr - *bgn_curr + 1;
+ *bgn_best = *bgn_curr;
+ *end_best = *end_curr;
+ }
} else {
- mcc_instruction = RW_MGR_LFSR_WR_RD_BANK_0;
- writel(RW_MGR_LFSR_WR_RD_BANK_0_NOP,
- &sdr_rw_load_jump_mgr_regs->load_jump_add3);
- }
- }
-
- writel(0, SDR_PHYGRP_RWMGRGRP_ADDRESS |
- RW_MGR_RESET_READ_DATAPATH_OFFSET);
-
- if (quick_write_mode)
- writel(0x08, &sdr_rw_load_mgr_regs->load_cntr0);
- else
- writel(0x40, &sdr_rw_load_mgr_regs->load_cntr0);
-
- writel(mcc_instruction, &sdr_rw_load_jump_mgr_regs->load_jump_add0);
-
- /*
- * CNTR 1 - This is used to ensure enough time elapses
- * for read data to come back.
- */
- writel(0x30, &sdr_rw_load_mgr_regs->load_cntr1);
-
- if (test_dm) {
- writel(RW_MGR_LFSR_WR_RD_DM_BANK_0_WAIT,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- } else {
- writel(RW_MGR_LFSR_WR_RD_BANK_0_WAIT,
- &sdr_rw_load_jump_mgr_regs->load_jump_add1);
- }
-
- addr = SDR_PHYGRP_RWMGRGRP_ADDRESS | RW_MGR_RUN_SINGLE_GROUP_OFFSET;
- writel(mcc_instruction, addr + (group << 2));
-}
-
-/* Test writes, can check for a single bit pass or multiple bit pass */
-static uint32_t rw_mgr_mem_calibrate_write_test(uint32_t rank_bgn,
- uint32_t write_group, uint32_t use_dm, uint32_t all_correct,
- uint32_t *bit_chk, uint32_t all_ranks)
-{
- uint32_t r;
- uint32_t correct_mask_vg;
- uint32_t tmp_bit_chk;
- uint32_t vg;
- uint32_t rank_end = all_ranks ? RW_MGR_MEM_NUMBER_OF_RANKS :
- (rank_bgn + NUM_RANKS_PER_SHADOW_REG);
- uint32_t addr_rw_mgr;
- uint32_t base_rw_mgr;
-
- *bit_chk = param->write_correct_mask;
- correct_mask_vg = param->write_correct_mask_vg;
-
- for (r = rank_bgn; r < rank_end; r++) {
- if (param->skip_ranks[r]) {
- /* request to skip the rank */
- continue;
- }
+ /* We just saw a failing test. Reset temp edge. */
+ *bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
+ *end_curr = IO_IO_OUT1_DELAY_MAX + 1;
- /* set rank */
- set_rank_and_odt_mask(r, RW_MGR_ODT_MODE_READ_WRITE);
-
- tmp_bit_chk = 0;
- addr_rw_mgr = SDR_PHYGRP_RWMGRGRP_ADDRESS;
- for (vg = RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS-1; ; vg--) {
- /* reset the fifos to get pointers to known state */
- writel(0, &phy_mgr_cmd->fifo_reset);
-
- tmp_bit_chk = tmp_bit_chk <<
- (RW_MGR_MEM_DQ_PER_WRITE_DQS /
- RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS);
- rw_mgr_mem_calibrate_write_test_issue(write_group *
- RW_MGR_MEM_VIRTUAL_GROUPS_PER_WRITE_DQS+vg,
- use_dm);
+ /* Early exit is only applicable to DQS. */
+ if (search_dm)
+ continue;
- base_rw_mgr = readl(addr_rw_mgr);
- tmp_bit_chk = tmp_bit_chk | (correct_mask_vg & ~(base_rw_mgr));
- if (vg == 0)
+ /*
+ * Early exit optimization: if the remaining delay
+ * chain space is less than already seen largest
+ * window we can exit.
+ */
+ if (*win_best - 1 > IO_IO_OUT1_DELAY_MAX - new_dqs - d)
break;
}
- *bit_chk &= tmp_bit_chk;
- }
-
- if (all_correct) {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "write_test(%u,%u,ALL) : %u == \
- %u => %lu", write_group, use_dm,
- *bit_chk, param->write_correct_mask,
- (long unsigned int)(*bit_chk ==
- param->write_correct_mask));
- return *bit_chk == param->write_correct_mask;
- } else {
- set_rank_and_odt_mask(0, RW_MGR_ODT_MODE_OFF);
- debug_cond(DLEVEL == 2, "write_test(%u,%u,ONE) : %u != ",
- write_group, use_dm, *bit_chk);
- debug_cond(DLEVEL == 2, "%lu" " => %lu", (long unsigned int)0,
- (long unsigned int)(*bit_chk != 0));
- return *bit_chk != 0x00;
}
}
/*
- * center all windows. do per-bit-deskew to possibly increase size of
+ * rw_mgr_mem_calibrate_writes_center() - Center all windows
+ * @rank_bgn: Rank number
+ * @write_group: Write group
+ * @test_bgn: Rank at which the test begins
+ *
+ * Center all windows. Do per-bit-deskew to possibly increase size of
* certain windows.
*/
-static uint32_t rw_mgr_mem_calibrate_writes_center(uint32_t rank_bgn,
- uint32_t write_group, uint32_t test_bgn)
+static int
+rw_mgr_mem_calibrate_writes_center(const u32 rank_bgn, const u32 write_group,
+ const u32 test_bgn)
{
- uint32_t i, p, min_index;
- int32_t d;
- /*
- * Store these as signed since there are comparisons with
- * signed numbers.
- */
- uint32_t bit_chk;
- uint32_t sticky_bit_chk;
- int32_t left_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS];
- int32_t right_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS];
- int32_t mid;
- int32_t mid_min, orig_mid_min;
- int32_t new_dqs, start_dqs, shift_dq;
- int32_t dq_margin, dqs_margin, dm_margin;
- uint32_t stop;
- uint32_t temp_dq_out1_delay;
- uint32_t addr;
+ int i;
+ u32 sticky_bit_chk;
+ u32 min_index;
+ int left_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS];
+ int right_edge[RW_MGR_MEM_DQ_PER_WRITE_DQS];
+ int mid;
+ int mid_min, orig_mid_min;
+ int new_dqs, start_dqs;
+ int dq_margin, dqs_margin, dm_margin;
+ int bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
+ int end_curr = IO_IO_OUT1_DELAY_MAX + 1;
+ int bgn_best = IO_IO_OUT1_DELAY_MAX + 1;
+ int end_best = IO_IO_OUT1_DELAY_MAX + 1;
+ int win_best = 0;
+
+ int ret;
debug("%s:%d %u %u", __func__, __LINE__, write_group, test_bgn);
dm_margin = 0;
- addr = SDR_PHYGRP_SCCGRP_ADDRESS | SCC_MGR_IO_OUT1_DELAY_OFFSET;
- start_dqs = readl(addr +
+ start_dqs = readl((SDR_PHYGRP_SCCGRP_ADDRESS |
+ SCC_MGR_IO_OUT1_DELAY_OFFSET) +
(RW_MGR_MEM_DQ_PER_WRITE_DQS << 2));
- /* per-bit deskew */
+ /* Per-bit deskew. */
/*
- * set the left and right edge of each bit to an illegal value
- * use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value.
+ * Set the left and right edge of each bit to an illegal value.
+ * Use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value.
*/
sticky_bit_chk = 0;
for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
right_edge[i] = IO_IO_OUT1_DELAY_MAX + 1;
}
- /* Search for the left edge of the window for each bit */
- for (d = 0; d <= IO_IO_OUT1_DELAY_MAX; d++) {
- scc_mgr_apply_group_dq_out1_delay(write_group, d);
-
- writel(0, &sdr_scc_mgr->update);
-
- /*
- * Stop searching when the read test doesn't pass AND when
- * we've seen a passing read on every bit.
- */
- stop = !rw_mgr_mem_calibrate_write_test(rank_bgn, write_group,
- 0, PASS_ONE_BIT, &bit_chk, 0);
- sticky_bit_chk = sticky_bit_chk | bit_chk;
- stop = stop && (sticky_bit_chk == param->write_correct_mask);
- debug_cond(DLEVEL == 2, "write_center(left): dtap=%d => %u \
- == %u && %u [bit_chk= %u ]\n",
- d, sticky_bit_chk, param->write_correct_mask,
- stop, bit_chk);
-
- if (stop == 1) {
- break;
- } else {
- for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
- if (bit_chk & 1) {
- /*
- * Remember a passing test as the
- * left_edge.
- */
- left_edge[i] = d;
- } else {
- /*
- * If a left edge has not been seen
- * yet, then a future passing test will
- * mark this edge as the right edge.
- */
- if (left_edge[i] ==
- IO_IO_OUT1_DELAY_MAX + 1) {
- right_edge[i] = -(d + 1);
- }
- }
- debug_cond(DLEVEL == 2, "write_center[l,d=%d):", d);
- debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d",
- (int)(bit_chk & 1), i, left_edge[i]);
- debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i,
- right_edge[i]);
- bit_chk = bit_chk >> 1;
- }
- }
- }
-
- /* Reset DQ delay chains to 0 */
- scc_mgr_apply_group_dq_out1_delay(0);
- sticky_bit_chk = 0;
- for (i = RW_MGR_MEM_DQ_PER_WRITE_DQS - 1;; i--) {
- debug_cond(DLEVEL == 2, "%s:%d write_center: left_edge[%u]: \
- %d right_edge[%u]: %d\n", __func__, __LINE__,
- i, left_edge[i], i, right_edge[i]);
-
- /*
- * Check for cases where we haven't found the left edge,
- * which makes our assignment of the the right edge invalid.
- * Reset it to the illegal value.
- */
- if ((left_edge[i] == IO_IO_OUT1_DELAY_MAX + 1) &&
- (right_edge[i] != IO_IO_OUT1_DELAY_MAX + 1)) {
- right_edge[i] = IO_IO_OUT1_DELAY_MAX + 1;
- debug_cond(DLEVEL == 2, "%s:%d write_center: reset \
- right_edge[%u]: %d\n", __func__, __LINE__,
- i, right_edge[i]);
- }
+ /* Search for the left edge of the window for each bit. */
+ search_left_edge(1, rank_bgn, write_group, 0, test_bgn,
+ &sticky_bit_chk,
+ left_edge, right_edge, 0);
- /*
- * Reset sticky bit (except for bits where we have
- * seen the left edge).
- */
- sticky_bit_chk = sticky_bit_chk << 1;
- if ((left_edge[i] != IO_IO_OUT1_DELAY_MAX + 1))
- sticky_bit_chk = sticky_bit_chk | 1;
-
- if (i == 0)
- break;
- }
-
- /* Search for the right edge of the window for each bit */
- for (d = 0; d <= IO_IO_OUT1_DELAY_MAX - start_dqs; d++) {
- scc_mgr_apply_group_dqs_io_and_oct_out1(write_group,
- d + start_dqs);
-
- writel(0, &sdr_scc_mgr->update);
-
- /*
- * Stop searching when the read test doesn't pass AND when
- * we've seen a passing read on every bit.
- */
- stop = !rw_mgr_mem_calibrate_write_test(rank_bgn, write_group,
- 0, PASS_ONE_BIT, &bit_chk, 0);
-
- sticky_bit_chk = sticky_bit_chk | bit_chk;
- stop = stop && (sticky_bit_chk == param->write_correct_mask);
-
- debug_cond(DLEVEL == 2, "write_center (right): dtap=%u => %u == \
- %u && %u\n", d, sticky_bit_chk,
- param->write_correct_mask, stop);
-
- if (stop == 1) {
- if (d == 0) {
- for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS;
- i++) {
- /* d = 0 failed, but it passed when
- testing the left edge, so it must be
- marginal, set it to -1 */
- if (right_edge[i] ==
- IO_IO_OUT1_DELAY_MAX + 1 &&
- left_edge[i] !=
- IO_IO_OUT1_DELAY_MAX + 1) {
- right_edge[i] = -1;
- }
- }
- }
- break;
- } else {
- for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
- if (bit_chk & 1) {
- /*
- * Remember a passing test as
- * the right_edge.
- */
- right_edge[i] = d;
- } else {
- if (d != 0) {
- /*
- * If a right edge has not
- * been seen yet, then a future
- * passing test will mark this
- * edge as the left edge.
- */
- if (right_edge[i] ==
- IO_IO_OUT1_DELAY_MAX + 1)
- left_edge[i] = -(d + 1);
- } else {
- /*
- * d = 0 failed, but it passed
- * when testing the left edge,
- * so it must be marginal, set
- * it to -1.
- */
- if (right_edge[i] ==
- IO_IO_OUT1_DELAY_MAX + 1 &&
- left_edge[i] !=
- IO_IO_OUT1_DELAY_MAX + 1)
- right_edge[i] = -1;
- /*
- * If a right edge has not been
- * seen yet, then a future
- * passing test will mark this
- * edge as the left edge.
- */
- else if (right_edge[i] ==
- IO_IO_OUT1_DELAY_MAX +
- 1)
- left_edge[i] = -(d + 1);
- }
- }
- debug_cond(DLEVEL == 2, "write_center[r,d=%d):", d);
- debug_cond(DLEVEL == 2, "bit_chk_test=%d left_edge[%u]: %d",
- (int)(bit_chk & 1), i, left_edge[i]);
- debug_cond(DLEVEL == 2, "right_edge[%u]: %d\n", i,
- right_edge[i]);
- bit_chk = bit_chk >> 1;
- }
- }
- }
-
- /* Check that all bits have a window */
- for (i = 0; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
- debug_cond(DLEVEL == 2, "%s:%d write_center: left_edge[%u]: \
- %d right_edge[%u]: %d", __func__, __LINE__,
- i, left_edge[i], i, right_edge[i]);
- if ((left_edge[i] == IO_IO_OUT1_DELAY_MAX + 1) ||
- (right_edge[i] == IO_IO_OUT1_DELAY_MAX + 1)) {
- set_failing_group_stage(test_bgn + i,
- CAL_STAGE_WRITES,
- CAL_SUBSTAGE_WRITES_CENTER);
- return 0;
- }
- }
-
- /* Find middle of window for each DQ bit */
- mid_min = left_edge[0] - right_edge[0];
- min_index = 0;
- for (i = 1; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++) {
- mid = left_edge[i] - right_edge[i];
- if (mid < mid_min) {
- mid_min = mid;
- min_index = i;
- }
+ /* Search for the right edge of the window for each bit. */
+ ret = search_right_edge(1, rank_bgn, write_group, 0,
+ start_dqs, 0,
+ &sticky_bit_chk,
+ left_edge, right_edge, 0);
+ if (ret) {
+ set_failing_group_stage(test_bgn + ret - 1, CAL_STAGE_WRITES,
+ CAL_SUBSTAGE_WRITES_CENTER);
+ return -EINVAL;
}
- /*
- * -mid_min/2 represents the amount that we need to move DQS.
- * If mid_min is odd and positive we'll need to add one to
- * make sure the rounding in further calculations is correct
- * (always bias to the right), so just add 1 for all positive values.
- */
- if (mid_min > 0)
- mid_min++;
- mid_min = mid_min / 2;
- debug_cond(DLEVEL == 1, "%s:%d write_center: mid_min=%d\n", __func__,
- __LINE__, mid_min);
+ min_index = get_window_mid_index(1, left_edge, right_edge, &mid_min);
- /* Determine the amount we can change DQS (which is -mid_min) */
+ /* Determine the amount we can change DQS (which is -mid_min). */
orig_mid_min = mid_min;
new_dqs = start_dqs;
mid_min = 0;
- debug_cond(DLEVEL == 1, "%s:%d write_center: start_dqs=%d new_dqs=%d \
- mid_min=%d\n", __func__, __LINE__, start_dqs, new_dqs, mid_min);
- /* Initialize data for export structures */
- dqs_margin = IO_IO_OUT1_DELAY_MAX + 1;
- dq_margin = IO_IO_OUT1_DELAY_MAX + 1;
-
- /* add delay to bring centre of all DQ windows to the same "level" */
- for (i = 0, p = test_bgn; i < RW_MGR_MEM_DQ_PER_WRITE_DQS; i++, p++) {
- /* Use values before divide by 2 to reduce round off error */
- shift_dq = (left_edge[i] - right_edge[i] -
- (left_edge[min_index] - right_edge[min_index]))/2 +
- (orig_mid_min - mid_min);
-
- debug_cond(DLEVEL == 2, "%s:%d write_center: before: shift_dq \
- [%u]=%d\n", __func__, __LINE__, i, shift_dq);
-
- addr = SDR_PHYGRP_SCCGRP_ADDRESS | SCC_MGR_IO_OUT1_DELAY_OFFSET;
- temp_dq_out1_delay = readl(addr + (i << 2));
- if (shift_dq + (int32_t)temp_dq_out1_delay >
- (int32_t)IO_IO_OUT1_DELAY_MAX) {
- shift_dq = (int32_t)IO_IO_OUT1_DELAY_MAX - temp_dq_out1_delay;
- } else if (shift_dq + (int32_t)temp_dq_out1_delay < 0) {
- shift_dq = -(int32_t)temp_dq_out1_delay;
- }
- debug_cond(DLEVEL == 2, "write_center: after: shift_dq[%u]=%d\n",
- i, shift_dq);
- scc_mgr_set_dq_out1_delay(i, temp_dq_out1_delay + shift_dq);
- scc_mgr_load_dq(i);
-
- debug_cond(DLEVEL == 2, "write_center: margin[%u]=[%d,%d]\n", i,
- left_edge[i] - shift_dq + (-mid_min),
- right_edge[i] + shift_dq - (-mid_min));
- /* To determine values for export structures */
- if (left_edge[i] - shift_dq + (-mid_min) < dq_margin)
- dq_margin = left_edge[i] - shift_dq + (-mid_min);
+ debug_cond(DLEVEL == 1,
+ "%s:%d write_center: start_dqs=%d new_dqs=%d mid_min=%d\n",
+ __func__, __LINE__, start_dqs, new_dqs, mid_min);
- if (right_edge[i] + shift_dq - (-mid_min) < dqs_margin)
- dqs_margin = right_edge[i] + shift_dq - (-mid_min);
- }
+ /* Add delay to bring centre of all DQ windows to the same "level". */
+ center_dq_windows(1, left_edge, right_edge, mid_min, orig_mid_min,
+ min_index, 0, &dq_margin, &dqs_margin);
/* Move DQS */
scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, new_dqs);
debug_cond(DLEVEL == 2, "%s:%d write_center: DM\n", __func__, __LINE__);
/*
- * set the left and right edge of each bit to an illegal value,
- * use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value,
+ * Set the left and right edge of each bit to an illegal value.
+ * Use (IO_IO_OUT1_DELAY_MAX + 1) as an illegal value.
*/
left_edge[0] = IO_IO_OUT1_DELAY_MAX + 1;
right_edge[0] = IO_IO_OUT1_DELAY_MAX + 1;
- int32_t bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
- int32_t end_curr = IO_IO_OUT1_DELAY_MAX + 1;
- int32_t bgn_best = IO_IO_OUT1_DELAY_MAX + 1;
- int32_t end_best = IO_IO_OUT1_DELAY_MAX + 1;
- int32_t win_best = 0;
-
- /* Search for the/part of the window with DM shift */
- for (d = IO_IO_OUT1_DELAY_MAX; d >= 0; d -= DELTA_D) {
- scc_mgr_apply_group_dm_out1_delay(d);
- writel(0, &sdr_scc_mgr->update);
- if (rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 1,
- PASS_ALL_BITS, &bit_chk,
- 0)) {
- /* USE Set current end of the window */
- end_curr = -d;
- /*
- * If a starting edge of our window has not been seen
- * this is our current start of the DM window.
- */
- if (bgn_curr == IO_IO_OUT1_DELAY_MAX + 1)
- bgn_curr = -d;
+ /* Search for the/part of the window with DM shift. */
+ search_window(1, rank_bgn, write_group, &bgn_curr, &end_curr,
+ &bgn_best, &end_best, &win_best, 0);
- /*
- * If current window is bigger than best seen.
- * Set best seen to be current window.
- */
- if ((end_curr-bgn_curr+1) > win_best) {
- win_best = end_curr-bgn_curr+1;
- bgn_best = bgn_curr;
- end_best = end_curr;
- }
- } else {
- /* We just saw a failing test. Reset temp edge */
- bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
- end_curr = IO_IO_OUT1_DELAY_MAX + 1;
- }
- }
-
-
- /* Reset DM delay chains to 0 */
+ /* Reset DM delay chains to 0. */
scc_mgr_apply_group_dm_out1_delay(0);
/*
* Check to see if the current window nudges up aganist 0 delay.
* If so we need to continue the search by shifting DQS otherwise DQS
- * search begins as a new search. */
+ * search begins as a new search.
+ */
if (end_curr != 0) {
bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
end_curr = IO_IO_OUT1_DELAY_MAX + 1;
}
- /* Search for the/part of the window with DQS shifts */
- for (d = 0; d <= IO_IO_OUT1_DELAY_MAX - new_dqs; d += DELTA_D) {
- /*
- * Note: This only shifts DQS, so are we limiting ourselve to
- * width of DQ unnecessarily.
- */
- scc_mgr_apply_group_dqs_io_and_oct_out1(write_group,
- d + new_dqs);
-
- writel(0, &sdr_scc_mgr->update);
- if (rw_mgr_mem_calibrate_write_test(rank_bgn, write_group, 1,
- PASS_ALL_BITS, &bit_chk,
- 0)) {
- /* USE Set current end of the window */
- end_curr = d;
- /*
- * If a beginning edge of our window has not been seen
- * this is our current begin of the DM window.
- */
- if (bgn_curr == IO_IO_OUT1_DELAY_MAX + 1)
- bgn_curr = d;
-
- /*
- * If current window is bigger than best seen. Set best
- * seen to be current window.
- */
- if ((end_curr-bgn_curr+1) > win_best) {
- win_best = end_curr-bgn_curr+1;
- bgn_best = bgn_curr;
- end_best = end_curr;
- }
- } else {
- /* We just saw a failing test. Reset temp edge */
- bgn_curr = IO_IO_OUT1_DELAY_MAX + 1;
- end_curr = IO_IO_OUT1_DELAY_MAX + 1;
-
- /* Early exit optimization: if ther remaining delay
- chain space is less than already seen largest window
- we can exit */
- if ((win_best-1) >
- (IO_IO_OUT1_DELAY_MAX - new_dqs - d)) {
- break;
- }
- }
- }
+ /* Search for the/part of the window with DQS shifts. */
+ search_window(0, rank_bgn, write_group, &bgn_curr, &end_curr,
+ &bgn_best, &end_best, &win_best, new_dqs);
- /* assign left and right edge for cal and reporting; */
- left_edge[0] = -1*bgn_best;
+ /* Assign left and right edge for cal and reporting. */
+ left_edge[0] = -1 * bgn_best;
right_edge[0] = end_best;
- debug_cond(DLEVEL == 2, "%s:%d dm_calib: left=%d right=%d\n", __func__,
- __LINE__, left_edge[0], right_edge[0]);
+ debug_cond(DLEVEL == 2, "%s:%d dm_calib: left=%d right=%d\n",
+ __func__, __LINE__, left_edge[0], right_edge[0]);
- /* Move DQS (back to orig) */
+ /* Move DQS (back to orig). */
scc_mgr_apply_group_dqs_io_and_oct_out1(write_group, new_dqs);
/* Move DM */
- /* Find middle of window for the DM bit */
+ /* Find middle of window for the DM bit. */
mid = (left_edge[0] - right_edge[0]) / 2;
- /* only move right, since we are not moving DQS/DQ */
+ /* Only move right, since we are not moving DQS/DQ. */
if (mid < 0)
mid = 0;
- /* dm_marign should fail if we never find a window */
+ /* dm_marign should fail if we never find a window. */
if (win_best == 0)
dm_margin = -1;
else
scc_mgr_apply_group_dm_out1_delay(mid);
writel(0, &sdr_scc_mgr->update);
- debug_cond(DLEVEL == 2, "%s:%d dm_calib: left=%d right=%d mid=%d \
- dm_margin=%d\n", __func__, __LINE__, left_edge[0],
- right_edge[0], mid, dm_margin);
- /* Export values */
+ debug_cond(DLEVEL == 2,
+ "%s:%d dm_calib: left=%d right=%d mid=%d dm_margin=%d\n",
+ __func__, __LINE__, left_edge[0], right_edge[0],
+ mid, dm_margin);
+ /* Export values. */
gbl->fom_out += dq_margin + dqs_margin;
- debug_cond(DLEVEL == 2, "%s:%d write_center: dq_margin=%d \
- dqs_margin=%d dm_margin=%d\n", __func__, __LINE__,
- dq_margin, dqs_margin, dm_margin);
+ debug_cond(DLEVEL == 2,
+ "%s:%d write_center: dq_margin=%d dqs_margin=%d dm_margin=%d\n",
+ __func__, __LINE__, dq_margin, dqs_margin, dm_margin);
/*
* Do not remove this line as it makes sure all of our
* decisions have been applied.
*/
writel(0, &sdr_scc_mgr->update);
- return (dq_margin >= 0) && (dqs_margin >= 0) && (dm_margin >= 0);
+
+ if ((dq_margin < 0) || (dqs_margin < 0) || (dm_margin < 0))
+ return -EINVAL;
+
+ return 0;
}
-/* calibrate the write operations */
-static uint32_t rw_mgr_mem_calibrate_writes(uint32_t rank_bgn, uint32_t g,
- uint32_t test_bgn)
+/**
+ * rw_mgr_mem_calibrate_writes() - Write Calibration Part One
+ * @rank_bgn: Rank number
+ * @group: Read/Write Group
+ * @test_bgn: Rank at which the test begins
+ *
+ * Stage 2: Write Calibration Part One.
+ *
+ * This function implements UniPHY calibration Stage 2, as explained in
+ * detail in Altera EMI_RM 2015.05.04 , "UniPHY Calibration Stages".
+ */
+static int rw_mgr_mem_calibrate_writes(const u32 rank_bgn, const u32 group,
+ const u32 test_bgn)
{
- /* update info for sims */
- debug("%s:%d %u %u\n", __func__, __LINE__, g, test_bgn);
+ int ret;
+
+ /* Update info for sims */
+ debug("%s:%d %u %u\n", __func__, __LINE__, group, test_bgn);
+ reg_file_set_group(group);
reg_file_set_stage(CAL_STAGE_WRITES);
reg_file_set_sub_stage(CAL_SUBSTAGE_WRITES_CENTER);
- reg_file_set_group(g);
-
- if (!rw_mgr_mem_calibrate_writes_center(rank_bgn, g, test_bgn)) {
- set_failing_group_stage(g, CAL_STAGE_WRITES,
+ ret = rw_mgr_mem_calibrate_writes_center(rank_bgn, group, test_bgn);
+ if (ret)
+ set_failing_group_stage(group, CAL_STAGE_WRITES,
CAL_SUBSTAGE_WRITES_CENTER);
- return 0;
- }
- return 1;
+ return ret;
}
/**
continue;
/* Calibrate WRITEs */
- if (rw_mgr_mem_calibrate_writes(rank_bgn,
+ if (!rw_mgr_mem_calibrate_writes(rank_bgn,
write_group, write_test_bgn))
continue;
if (STATIC_CALIB_STEPS & CALIB_SKIP_WRITES)
continue;
- if (rw_mgr_mem_calibrate_vfifo_end(read_group,
+ if (!rw_mgr_mem_calibrate_vfifo_end(read_group,
read_test_bgn))
continue;