* this program; if not, write to the Free Software Foundation, Inc., 59
* Temple Place - Suite 330, Boston, MA 02111-1307, USA.
*
- * The full GNU General Public License is iin this distribution in the
+ * The full GNU General Public License is in this distribution in the
* file called COPYING.
*
* Documentation: ARM DDI 0196G == PL080
*
* ASSUMES default (little) endianness for DMA transfers
*
- * Only DMAC flow control is implemented
+ * The PL08x has two flow control settings:
+ * - DMAC flow control: the transfer size defines the number of transfers
+ * which occur for the current LLI entry, and the DMAC raises TC at the
+ * end of every LLI entry. Observed behaviour shows the DMAC listening
+ * to both the BREQ and SREQ signals (contrary to documented),
+ * transferring data if either is active. The LBREQ and LSREQ signals
+ * are ignored.
+ *
+ * - Peripheral flow control: the transfer size is ignored (and should be
+ * zero). The data is transferred from the current LLI entry, until
+ * after the final transfer signalled by LBREQ or LSREQ. The DMAC
+ * will then move to the next LLI entry.
+ *
+ * Only the former works sanely with scatter lists, so we only implement
+ * the DMAC flow control method. However, peripherals which use the LBREQ
+ * and LSREQ signals (eg, MMCI) are unable to use this mode, which through
+ * these hardware restrictions prevents them from using scatter DMA.
*
* Global TODO:
* - Break out common code from arch/arm/mach-s3c64xx and share
#include <linux/device.h>
#include <linux/init.h>
#include <linux/module.h>
-#include <linux/pci.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
#include <linux/dmapool.h>
-#include <linux/amba/bus.h>
#include <linux/dmaengine.h>
+#include <linux/amba/bus.h>
#include <linux/amba/pl08x.h>
#include <linux/debugfs.h>
#include <linux/seq_file.h>
#include <asm/hardware/pl080.h>
-#include <asm/dma.h>
-#include <asm/mach/dma.h>
-#include <asm/atomic.h>
-#include <asm/processor.h>
-#include <asm/cacheflush.h>
#define DRIVER_NAME "pl08xdmac"
/**
* struct vendor_data - vendor-specific config parameters
- * for PL08x derivates
- * @name: the name of this specific variant
+ * for PL08x derivatives
* @channels: the number of channels available in this variant
* @dualmaster: whether this version supports dual AHB masters
* or not.
*/
struct vendor_data {
- char *name;
u8 channels;
bool dualmaster;
};
/*
* PL08X private data structures
- * An LLI struct - see pl08x TRM
- * Note that next uses bit[0] as a bus bit,
- * start & end do not - their bus bit info
- * is in cctl
+ * An LLI struct - see PL08x TRM. Note that next uses bit[0] as a bus bit,
+ * start & end do not - their bus bit info is in cctl.
*/
-struct lli {
+struct pl08x_lli {
dma_addr_t src;
dma_addr_t dst;
dma_addr_t next;
struct dma_device memcpy;
void __iomem *base;
struct amba_device *adev;
- struct vendor_data *vd;
+ const struct vendor_data *vd;
struct pl08x_platform_data *pd;
struct pl08x_phy_chan *phy_chans;
struct dma_pool *pool;
/* Size (bytes) of each LLI buffer allocated for one transfer */
# define PL08X_LLI_TSFR_SIZE 0x2000
-/* Maximimum times we call dma_pool_alloc on this pool without freeing */
+/* Maximum times we call dma_pool_alloc on this pool without freeing */
#define PL08X_MAX_ALLOCS 0x40
-#define MAX_NUM_TSFR_LLIS (PL08X_LLI_TSFR_SIZE/sizeof(struct lli))
+#define MAX_NUM_TSFR_LLIS (PL08X_LLI_TSFR_SIZE/sizeof(struct pl08x_lli))
#define PL08X_ALIGN 8
static inline struct pl08x_dma_chan *to_pl08x_chan(struct dma_chan *chan)
/*
* Set the initial DMA register values i.e. those for the first LLI
- * The next lli pointer and the configuration interrupt bit have
+ * The next LLI pointer and the configuration interrupt bit have
* been set when the LLIs were constructed
*/
static void pl08x_set_cregs(struct pl08x_driver_data *pl08x,
{
/* Wait for channel inactive */
while (pl08x_phy_channel_busy(ch))
- ;
+ cpu_relax();
dev_vdbg(&pl08x->adev->dev,
- "WRITE channel %d: csrc=%08x, cdst=%08x, "
- "cctl=%08x, clli=%08x, ccfg=%08x\n",
+ "WRITE channel %d: csrc=0x%08x, cdst=0x%08x, "
+ "cctl=0x%08x, clli=0x%08x, ccfg=0x%08x\n",
ch->id,
ch->csrc,
ch->cdst,
* Do not access config register until channel shows as disabled
*/
while (readl(pl08x->base + PL080_EN_CHAN) & (1 << ch->id))
- ;
+ cpu_relax();
/*
* Do not access config register until channel shows as inactive
/* Wait for channel inactive */
while (pl08x_phy_channel_busy(ch))
- ;
+ cpu_relax();
}
static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
struct pl08x_txd *txdi = NULL;
struct pl08x_txd *txd;
unsigned long flags;
- u32 bytes = 0;
+ size_t bytes = 0;
spin_lock_irqsave(&plchan->lock, flags);
* currently active transaction.
*/
if (ch && txd) {
- struct lli *llis_va = txd->llis_va;
- struct lli *llis_bus = (struct lli *) txd->llis_bus;
- u32 clli = readl(ch->base + PL080_CH_LLI);
+ struct pl08x_lli *llis_va = txd->llis_va;
+ struct pl08x_lli *llis_bus = (struct pl08x_lli *) txd->llis_bus;
+ u32 clli = readl(ch->base + PL080_CH_LLI) & ~PL080_LLI_LM_AHB2;
/* First get the bytes in the current active LLI */
bytes = get_bytes_in_cctl(readl(ch->base + PL080_CH_CONTROL));
while (clli) {
bytes += get_bytes_in_cctl(llis_va[i].cctl);
/*
- * A clli of 0x00000000 will terminate the
- * LLI list
+ * A LLI pointer of 0 terminates the LLI list
*/
clli = llis_va[i].next;
i++;
}
static inline u32 pl08x_cctl_bits(u32 cctl, u8 srcwidth, u8 dstwidth,
- u32 tsize)
+ size_t tsize)
{
u32 retbits = cctl;
- /* Remove all src, dst and transfersize bits */
+ /* Remove all src, dst and transfer size bits */
retbits &= ~PL080_CONTROL_DWIDTH_MASK;
retbits &= ~PL080_CONTROL_SWIDTH_MASK;
retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
* this prefers the destination bus if both available
* if fixed address on one bus the other will be chosen
*/
-void pl08x_choose_master_bus(struct pl08x_bus_data *src_bus,
+static void pl08x_choose_master_bus(struct pl08x_bus_data *src_bus,
struct pl08x_bus_data *dst_bus, struct pl08x_bus_data **mbus,
struct pl08x_bus_data **sbus, u32 cctl)
{
* Fills in one LLI for a certain transfer descriptor
* and advance the counter
*/
-int pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
+static int pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
struct pl08x_txd *txd, int num_llis, int len,
u32 cctl, u32 *remainder)
{
- struct lli *llis_va = txd->llis_va;
- struct lli *llis_bus = (struct lli *) txd->llis_bus;
+ struct pl08x_lli *llis_va = txd->llis_va;
+ dma_addr_t llis_bus = txd->llis_bus;
BUG_ON(num_llis >= MAX_NUM_TSFR_LLIS);
* memory. So we don't manipulate this bit currently.
*/
- llis_va[num_llis].next =
- (dma_addr_t)((u32) &(llis_bus[num_llis + 1]));
+ llis_va[num_llis].next = llis_bus + (num_llis + 1) * sizeof(struct pl08x_lli);
if (cctl & PL080_CONTROL_SRC_INCR)
txd->srcbus.addr += len;
if (cctl & PL080_CONTROL_DST_INCR)
txd->dstbus.addr += len;
+ BUG_ON(*remainder < len);
+
*remainder -= len;
return num_llis + 1;
/*
* Return number of bytes to fill to boundary, or len
*/
-static inline u32 pl08x_pre_boundary(u32 addr, u32 len)
+static inline size_t pl08x_pre_boundary(u32 addr, size_t len)
{
u32 boundary;
{
struct pl08x_channel_data *cd = txd->cd;
struct pl08x_bus_data *mbus, *sbus;
- u32 remainder;
+ size_t remainder;
int num_llis = 0;
u32 cctl;
- int max_bytes_per_lli;
- int total_bytes = 0;
- struct lli *llis_va;
- struct lli *llis_bus;
-
- if (!txd) {
- dev_err(&pl08x->adev->dev, "%s no descriptor\n", __func__);
- return 0;
- }
+ size_t max_bytes_per_lli;
+ size_t total_bytes = 0;
+ struct pl08x_lli *llis_va;
txd->llis_va = dma_pool_alloc(pl08x->pool, GFP_NOWAIT,
&txd->llis_bus);
max_bytes_per_lli = min(txd->srcbus.buswidth, txd->dstbus.buswidth) *
PL080_CONTROL_TRANSFER_SIZE_MASK;
dev_vdbg(&pl08x->adev->dev,
- "%s max bytes per lli = %d\n",
+ "%s max bytes per lli = %zu\n",
__func__, max_bytes_per_lli);
/* We need to count this down to zero */
remainder = txd->len;
dev_vdbg(&pl08x->adev->dev,
- "%s remainder = %d\n",
+ "%s remainder = %zu\n",
__func__, remainder);
/*
* Choose bus to align to
* - prefers destination bus if both available
* - if fixed address on one bus chooses other
- * - modifies cctl to choose an apropriate master
+ * - modifies cctl to choose an appropriate master
*/
pl08x_choose_master_bus(&txd->srcbus, &txd->dstbus,
&mbus, &sbus, cctl);
while (remainder) {
dev_vdbg(&pl08x->adev->dev,
"%s single byte LLIs for a transfer of "
- "less than a bus width (remain %08x)\n",
+ "less than a bus width (remain 0x%08x)\n",
__func__, remainder);
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
num_llis =
while ((mbus->addr) % (mbus->buswidth)) {
dev_vdbg(&pl08x->adev->dev,
"%s adjustment lli for less than bus width "
- "(remain %08x)\n",
+ "(remain 0x%08x)\n",
__func__, remainder);
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
num_llis = pl08x_fill_lli_for_desc
* width left
*/
while (remainder > (mbus->buswidth - 1)) {
- int lli_len, target_len;
- int tsize;
- int odd_bytes;
+ size_t lli_len, target_len, tsize, odd_bytes;
/*
* If enough left try to send max possible,
target_len = max_bytes_per_lli;
/*
- * Set bus lengths for incrementing busses
+ * Set bus lengths for incrementing buses
* to number of bytes which fill to next memory
* boundary
*/
if (lli_len <= 0) {
dev_err(&pl08x->adev->dev,
- "%s lli_len is %d, <= 0\n",
+ "%s lli_len is %zu, <= 0\n",
__func__, lli_len);
return 0;
}
/*
* So now we know how many bytes to transfer
* to get to the nearest boundary
- * The next lli will past the boundary
+ * The next LLI will past the boundary
* - however we may be working to a boundary
* on the slave bus
* We need to ensure the master stays aligned
if (target_len != lli_len) {
dev_vdbg(&pl08x->adev->dev,
- "%s can't send what we want. Desired %08x, lli of %08x bytes in txd of %08x\n",
+ "%s can't send what we want. Desired 0x%08zx, lli of 0x%08zx bytes in txd of 0x%08zx\n",
__func__, target_len, lli_len, txd->len);
}
tsize);
dev_vdbg(&pl08x->adev->dev,
- "%s fill lli with single lli chunk of size %08x (remainder %08x)\n",
+ "%s fill lli with single lli chunk of size 0x%08zx (remainder 0x%08zx)\n",
__func__, lli_len, remainder);
num_llis = pl08x_fill_lli_for_desc(pl08x, txd,
num_llis, lli_len, cctl,
&& (remainder); j++) {
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
dev_vdbg(&pl08x->adev->dev,
- "%s align with boundardy, single byte (remain %08x)\n",
+ "%s align with boundary, single byte (remain 0x%08zx)\n",
__func__, remainder);
num_llis =
pl08x_fill_lli_for_desc(pl08x,
/*
* Send any odd bytes
*/
- if (remainder < 0) {
- dev_err(&pl08x->adev->dev, "%s remainder not fitted 0x%08x bytes\n",
- __func__, remainder);
- return 0;
- }
-
while (remainder) {
cctl = pl08x_cctl_bits(cctl, 1, 1, 1);
dev_vdbg(&pl08x->adev->dev,
- "%s align with boundardy, single odd byte (remain %d)\n",
+ "%s align with boundary, single odd byte (remain %zu)\n",
__func__, remainder);
num_llis = pl08x_fill_lli_for_desc(pl08x, txd, num_llis,
1, cctl, &remainder);
}
if (total_bytes != txd->len) {
dev_err(&pl08x->adev->dev,
- "%s size of encoded lli:s don't match total txd, transferred 0x%08x from size 0x%08x\n",
+ "%s size of encoded lli:s don't match total txd, transferred 0x%08zx from size 0x%08zx\n",
__func__, total_bytes, txd->len);
return 0;
}
__func__, (u32) MAX_NUM_TSFR_LLIS);
return 0;
}
+
+ llis_va = txd->llis_va;
/*
- * Decide whether this is a loop or a terminated transfer
+ * The final LLI terminates the LLI.
*/
- llis_va = txd->llis_va;
- llis_bus = (struct lli *) txd->llis_bus;
-
- if (cd->circular_buffer) {
- /*
- * Loop the circular buffer so that the next element
- * points back to the beginning of the LLI.
- */
- llis_va[num_llis - 1].next =
- (dma_addr_t)((unsigned int)&(llis_bus[0]));
- } else {
- /*
- * On non-circular buffers, the final LLI terminates
- * the LLI.
- */
- llis_va[num_llis - 1].next = 0;
- /*
- * The final LLI element shall also fire an interrupt
- */
- llis_va[num_llis - 1].cctl |= PL080_CONTROL_TC_IRQ_EN;
- }
+ llis_va[num_llis - 1].next = 0;
+ /*
+ * The final LLI element shall also fire an interrupt
+ */
+ llis_va[num_llis - 1].cctl |= PL080_CONTROL_TC_IRQ_EN;
/* Now store the channel register values */
txd->csrc = llis_va[0].src;
txd->cdst = llis_va[0].dst;
- if (num_llis > 1)
- txd->clli = llis_va[0].next;
- else
- txd->clli = 0;
-
+ txd->clli = llis_va[0].next;
txd->cctl = llis_va[0].cctl;
/* ccfg will be set at physical channel allocation time */
for (i = 0; i < num_llis; i++) {
dev_vdbg(&pl08x->adev->dev,
- "lli %d @%p: csrc=%08x, cdst=%08x, cctl=%08x, clli=%08x\n",
+ "lli %d @%p: csrc=0x%08x, cdst=0x%08x, cctl=0x%08x, clli=0x%08x\n",
i,
&llis_va[i],
llis_va[i].src,
static void pl08x_free_txd(struct pl08x_driver_data *pl08x,
struct pl08x_txd *txd)
{
- if (!txd)
- dev_err(&pl08x->adev->dev,
- "%s no descriptor to free\n",
- __func__);
-
/* Free the LLI */
- dma_pool_free(pl08x->pool, txd->llis_va,
- txd->llis_bus);
+ dma_pool_free(pl08x->pool, txd->llis_va, txd->llis_bus);
pl08x->pool_ctr--;
return 0;
}
+static void release_phy_channel(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_driver_data *pl08x = plchan->host;
+
+ if ((plchan->phychan->signal >= 0) && pl08x->pd->put_signal) {
+ pl08x->pd->put_signal(plchan);
+ plchan->phychan->signal = -1;
+ }
+ pl08x_put_phy_channel(pl08x, plchan->phychan);
+ plchan->phychan = NULL;
+}
+
static dma_cookie_t pl08x_tx_submit(struct dma_async_tx_descriptor *tx)
{
struct pl08x_dma_chan *plchan = to_pl08x_chan(tx->chan);
- atomic_inc(&plchan->last_issued);
- tx->cookie = atomic_read(&plchan->last_issued);
+ plchan->chan.cookie += 1;
+ if (plchan->chan.cookie < 0)
+ plchan->chan.cookie = 1;
+ tx->cookie = plchan->chan.cookie;
/* This unlock follows the lock in the prep() function */
spin_unlock_irqrestore(&plchan->lock, plchan->lockflags);
enum dma_status ret;
u32 bytesleft = 0;
- last_used = atomic_read(&plchan->last_issued);
+ last_used = plchan->chan.cookie;
last_complete = plchan->lc;
ret = dma_async_is_complete(cookie, last_complete, last_used);
/*
* This cookie not complete yet
*/
- last_used = atomic_read(&plchan->last_issued);
+ last_used = plchan->chan.cookie;
last_complete = plchan->lc;
/* Get number of bytes left in the active transactions and queue */
u32 cctl = 0;
/* Mask out all except src and dst channel */
u32 ccfg = cd->ccfg & 0x000003DEU;
- int i = 0;
+ int i;
/* Transfer direction */
plchan->runtime_direction = config->direction;
/*
* Now decide on a maxburst:
- * If this channel will only request single transfers, set
- * this down to ONE element.
+ * If this channel will only request single transfers, set this
+ * down to ONE element. Also select one element if no maxburst
+ * is specified.
*/
- if (plchan->cd->single) {
+ if (plchan->cd->single || maxburst == 0) {
cctl |= (PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT) |
(PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT);
} else {
- while (i < ARRAY_SIZE(burst_sizes)) {
+ for (i = 0; i < ARRAY_SIZE(burst_sizes); i++)
if (burst_sizes[i].burstwords <= maxburst)
break;
- i++;
- }
cctl |= burst_sizes[i].reg;
}
dev_dbg(&pl08x->adev->dev,
"configured channel %s (%s) for %s, data width %d, "
- "maxburst %d words, LE, CCTL=%08x, CCFG=%08x\n",
+ "maxburst %d words, LE, CCTL=0x%08x, CCFG=0x%08x\n",
dma_chan_name(chan), plchan->name,
(config->direction == DMA_FROM_DEVICE) ? "RX" : "TX",
addr_width,
unsigned long flags;
spin_lock_irqsave(&plchan->lock, flags);
- /* Something is already active */
- if (plchan->at) {
- spin_unlock_irqrestore(&plchan->lock, flags);
- return;
- }
-
- /* Didn't get a physical channel so waiting for it ... */
- if (plchan->state == PL08X_CHAN_WAITING)
+ /* Something is already active, or we're waiting for a channel... */
+ if (plchan->at || plchan->state == PL08X_CHAN_WAITING) {
+ spin_unlock_irqrestore(&plchan->lock, flags);
return;
+ }
/* Take the first element in the queue and execute it */
if (!list_empty(&plchan->desc_list)) {
int ret;
num_llis = pl08x_fill_llis_for_desc(pl08x, txd);
-
- if (!num_llis)
+ if (!num_llis) {
+ kfree(txd);
return -EINVAL;
+ }
spin_lock_irqsave(&plchan->lock, plchan->lockflags);
- /*
- * If this device is not using a circular buffer then
- * queue this new descriptor for transfer.
- * The descriptor for a circular buffer continues
- * to be used until the channel is freed.
- */
- if (txd->cd->circular_buffer)
- dev_err(&pl08x->adev->dev,
- "%s attempting to queue a circular buffer\n",
- __func__);
- else
- list_add_tail(&txd->node,
- &plchan->desc_list);
+ list_add_tail(&txd->node, &plchan->desc_list);
/*
* See if we already have a physical channel allocated,
* available to handle it whereas slave transfers may
* have been denied due to platform channel muxing restrictions
* and since there is no guarantee that this will ever be
- * resolved, and since the signal must be aquired AFTER
- * aquiring the physical channel, we will let them be NACK:ed
+ * resolved, and since the signal must be acquired AFTER
+ * acquiring the physical channel, we will let them be NACK:ed
* with -EBUSY here. The drivers can alway retry the prep()
* call if they are eager on doing this using DMA.
*/
return 0;
}
+static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan)
+{
+ struct pl08x_txd *txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+
+ if (txd) {
+ dma_async_tx_descriptor_init(&txd->tx, &plchan->chan);
+ txd->tx.tx_submit = pl08x_tx_submit;
+ INIT_LIST_HEAD(&txd->node);
+ }
+ return txd;
+}
+
/*
* Initialize a descriptor to be used by memcpy submit
*/
struct pl08x_txd *txd;
int ret;
- txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+ txd = pl08x_get_txd(plchan);
if (!txd) {
dev_err(&pl08x->adev->dev,
"%s no memory for descriptor\n", __func__);
return NULL;
}
- dma_async_tx_descriptor_init(&txd->tx, chan);
txd->direction = DMA_NONE;
txd->srcbus.addr = src;
txd->dstbus.addr = dest;
txd->cd = &pl08x->pd->memcpy_channel;
/* Both to be incremented or the code will break */
txd->cd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
- txd->tx.tx_submit = pl08x_tx_submit;
- txd->tx.callback = NULL;
- txd->tx.callback_param = NULL;
txd->len = len;
- INIT_LIST_HEAD(&txd->node);
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
return NULL;
return &txd->tx;
}
-struct dma_async_tx_descriptor *pl08x_prep_slave_sg(
+static struct dma_async_tx_descriptor *pl08x_prep_slave_sg(
struct dma_chan *chan, struct scatterlist *sgl,
unsigned int sg_len, enum dma_data_direction direction,
unsigned long flags)
dev_dbg(&pl08x->adev->dev, "%s prepare transaction of %d bytes from %s\n",
__func__, sgl->length, plchan->name);
- txd = kzalloc(sizeof(struct pl08x_txd), GFP_NOWAIT);
+ txd = pl08x_get_txd(plchan);
if (!txd) {
dev_err(&pl08x->adev->dev, "%s no txd\n", __func__);
return NULL;
}
- dma_async_tx_descriptor_init(&txd->tx, chan);
-
if (direction != plchan->runtime_direction)
dev_err(&pl08x->adev->dev, "%s DMA setup does not match "
"the direction configured for the PrimeCell\n",
return NULL;
}
txd->cd = plchan->cd;
- txd->tx.tx_submit = pl08x_tx_submit;
- txd->tx.callback = NULL;
- txd->tx.callback_param = NULL;
txd->len = sgl->length;
- INIT_LIST_HEAD(&txd->node);
ret = pl08x_prep_channel_resources(plchan, txd);
if (ret)
* Mark physical channel as free and free any slave
* signal
*/
- if ((plchan->phychan->signal >= 0) &&
- pl08x->pd->put_signal) {
- pl08x->pd->put_signal(plchan);
- plchan->phychan->signal = -1;
- }
- pl08x_put_phy_channel(pl08x, plchan->phychan);
- plchan->phychan = NULL;
+ release_phy_channel(plchan);
}
- /* Stop any pending tasklet */
- tasklet_disable(&plchan->tasklet);
/* Dequeue jobs and free LLIs */
if (plchan->at) {
pl08x_free_txd(pl08x, plchan->at);
val = readl(pl08x->base + PL080_CONFIG);
val &= ~(PL080_CONFIG_M2_BE | PL080_CONFIG_M1_BE | PL080_CONFIG_ENABLE);
- /* We implictly clear bit 1 and that means little-endian mode */
+ /* We implicitly clear bit 1 and that means little-endian mode */
val |= PL080_CONFIG_ENABLE;
writel(val, pl08x->base + PL080_CONFIG);
}
static void pl08x_tasklet(unsigned long data)
{
struct pl08x_dma_chan *plchan = (struct pl08x_dma_chan *) data;
- struct pl08x_phy_chan *phychan = plchan->phychan;
struct pl08x_driver_data *pl08x = plchan->host;
+ unsigned long flags;
- if (!plchan)
- BUG();
-
- spin_lock(&plchan->lock);
+ spin_lock_irqsave(&plchan->lock, flags);
if (plchan->at) {
dma_async_tx_callback callback =
/*
* Update last completed
*/
- plchan->lc =
- (plchan->at->tx.cookie);
+ plchan->lc = plchan->at->tx.cookie;
/*
* Callback to signal completion
callback(callback_param);
/*
- * Device callbacks should NOT clear
- * the current transaction on the channel
- * Linus: sometimes they should?
- */
- if (!plchan->at)
- BUG();
-
- /*
- * Free the descriptor if it's not for a device
- * using a circular buffer
- */
- if (!plchan->at->cd->circular_buffer) {
- pl08x_free_txd(pl08x, plchan->at);
- plchan->at = NULL;
- }
- /*
- * else descriptor for circular
- * buffers only freed when
- * client has disabled dma
+ * Free the descriptor
*/
+ pl08x_free_txd(pl08x, plchan->at);
+ plchan->at = NULL;
}
/*
* If a new descriptor is queued, set it up
* No more jobs, so free up the physical channel
* Free any allocated signal on slave transfers too
*/
- if ((phychan->signal >= 0) && pl08x->pd->put_signal) {
- pl08x->pd->put_signal(plchan);
- phychan->signal = -1;
- }
- pl08x_put_phy_channel(pl08x, phychan);
- plchan->phychan = NULL;
+ release_phy_channel(plchan);
plchan->state = PL08X_CHAN_IDLE;
/*
}
}
- spin_unlock(&plchan->lock);
+ spin_unlock_irqrestore(&plchan->lock, flags);
}
static irqreturn_t pl08x_irq(int irq, void *dev)
return -ENOMEM;
}
}
+ if (chan->cd->circular_buffer) {
+ dev_err(&pl08x->adev->dev,
+ "channel %s: circular buffers not supported\n",
+ chan->name);
+ kfree(chan);
+ continue;
+ }
dev_info(&pl08x->adev->dev,
"initialize virtual channel \"%s\"\n",
chan->name);
chan->chan.device = dmadev;
- atomic_set(&chan->last_issued, 0);
- chan->lc = atomic_read(&chan->last_issued);
+ chan->chan.cookie = 0;
+ chan->lc = 0;
spin_lock_init(&chan->lock);
INIT_LIST_HEAD(&chan->desc_list);
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->memcpy.channels, chan.device_node) {
- seq_printf(s, "%s\t\t\%s\n", chan->name,
+ seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
}
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->slave.channels, chan.device_node) {
- seq_printf(s, "%s\t\t\%s\n", chan->name,
+ seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
}
static int pl08x_probe(struct amba_device *adev, struct amba_id *id)
{
struct pl08x_driver_data *pl08x;
- struct vendor_data *vd = id->data;
+ const struct vendor_data *vd = id->data;
int ret = 0;
int i;
writel(0x000000FF, pl08x->base + PL080_TC_CLEAR);
ret = request_irq(adev->irq[0], pl08x_irq, IRQF_DISABLED,
- vd->name, pl08x);
+ DRIVER_NAME, pl08x);
if (ret) {
dev_err(&adev->dev, "%s failed to request interrupt %d\n",
__func__, adev->irq[0]);
amba_set_drvdata(adev, pl08x);
init_pl08x_debugfs(pl08x);
- dev_info(&pl08x->adev->dev, "ARM(R) %s DMA block initialized @%08x\n",
- vd->name, adev->res.start);
+ dev_info(&pl08x->adev->dev, "DMA: PL%03x rev%u at 0x%08llx irq %d\n",
+ amba_part(adev), amba_rev(adev),
+ (unsigned long long)adev->res.start, adev->irq[0]);
return 0;
out_no_slave_reg:
/* PL080 has 8 channels and the PL080 have just 2 */
static struct vendor_data vendor_pl080 = {
- .name = "PL080",
.channels = 8,
.dualmaster = true,
};
static struct vendor_data vendor_pl081 = {
- .name = "PL081",
.channels = 2,
.dualmaster = false,
};
retval = amba_driver_register(&pl08x_amba_driver);
if (retval)
printk(KERN_WARNING DRIVER_NAME
- "failed to register as an amba device (%d)\n",
+ "failed to register as an AMBA device (%d)\n",
retval);
return retval;
}