#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/property.h>
-#include <linux/usb/phy.h>
#include <linux/notifier.h>
#include <linux/extcon.h>
#include <linux/regmap.h>
#define DET_STAT_CDP 2
#define DET_STAT_DCP 3
-/* IRQ enable-1 register */
-#define PWRSRC_IRQ_CFG_MASK (BIT(4)|BIT(3)|BIT(2))
-
-/* IRQ enable-6 register */
-#define BC12_IRQ_CFG_MASK BIT(1)
-
enum axp288_extcon_reg {
AXP288_PS_STAT_REG = 0x00,
AXP288_PS_BOOT_REASON_REG = 0x02,
AXP288_BC_VBUS_CNTL_REG = 0x2d,
AXP288_BC_USB_STAT_REG = 0x2e,
AXP288_BC_DET_STAT_REG = 0x2f,
- AXP288_PWRSRC_IRQ_CFG_REG = 0x40,
- AXP288_BC12_IRQ_CFG_REG = 0x45,
};
enum axp288_mux_select {
EXTCON_CHG_USB_SDP,
EXTCON_CHG_USB_CDP,
EXTCON_CHG_USB_DCP,
+ EXTCON_USB,
EXTCON_NONE,
};
struct device *dev;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irqc;
- struct axp288_extcon_pdata *pdata;
+ struct gpio_desc *gpio_mux_cntl;
int irq[EXTCON_IRQ_END];
struct extcon_dev *edev;
struct notifier_block extcon_nb;
- struct usb_phy *otg;
+ unsigned int previous_cable;
};
/* Power up/down reason string array */
static int axp288_handle_chrg_det_event(struct axp288_extcon_info *info)
{
- static bool notify_otg, notify_charger;
- static unsigned int cable;
int ret, stat, cfg, pwr_stat;
u8 chrg_type;
+ unsigned int cable = info->previous_cable;
bool vbus_attach = false;
ret = regmap_read(info->regmap, AXP288_PS_STAT_REG, &pwr_stat);
return ret;
}
- vbus_attach = (pwr_stat & PS_STAT_VBUS_PRESENT);
+ vbus_attach = (pwr_stat & PS_STAT_VBUS_VALID);
if (!vbus_attach)
- goto notify_otg;
+ goto no_vbus;
/* Check charger detection completion status */
ret = regmap_read(info->regmap, AXP288_BC_GLOBAL_REG, &cfg);
switch (chrg_type) {
case DET_STAT_SDP:
dev_dbg(info->dev, "sdp cable is connected\n");
- notify_otg = true;
- notify_charger = true;
cable = EXTCON_CHG_USB_SDP;
break;
case DET_STAT_CDP:
dev_dbg(info->dev, "cdp cable is connected\n");
- notify_otg = true;
- notify_charger = true;
cable = EXTCON_CHG_USB_CDP;
break;
case DET_STAT_DCP:
dev_dbg(info->dev, "dcp cable is connected\n");
- notify_charger = true;
cable = EXTCON_CHG_USB_DCP;
break;
default:
"disconnect or unknown or ID event\n");
}
-notify_otg:
- if (notify_otg) {
- /*
- * If VBUS is absent Connect D+/D- lines to PMIC for BC
- * detection. Else connect them to SOC for USB communication.
- */
- if (info->pdata->gpio_mux_cntl)
- gpiod_set_value(info->pdata->gpio_mux_cntl,
- vbus_attach ? EXTCON_GPIO_MUX_SEL_SOC
- : EXTCON_GPIO_MUX_SEL_PMIC);
-
- atomic_notifier_call_chain(&info->otg->notifier,
- vbus_attach ? USB_EVENT_VBUS : USB_EVENT_NONE, NULL);
- }
-
- if (notify_charger)
+no_vbus:
+ /*
+ * If VBUS is absent Connect D+/D- lines to PMIC for BC
+ * detection. Else connect them to SOC for USB communication.
+ */
+ if (info->gpio_mux_cntl)
+ gpiod_set_value(info->gpio_mux_cntl,
+ vbus_attach ? EXTCON_GPIO_MUX_SEL_SOC
+ : EXTCON_GPIO_MUX_SEL_PMIC);
+
+ extcon_set_state_sync(info->edev, info->previous_cable, false);
+ if (info->previous_cable == EXTCON_CHG_USB_SDP)
+ extcon_set_state_sync(info->edev, EXTCON_USB, false);
+
+ if (vbus_attach) {
extcon_set_state_sync(info->edev, cable, vbus_attach);
+ if (cable == EXTCON_CHG_USB_SDP)
+ extcon_set_state_sync(info->edev, EXTCON_USB,
+ vbus_attach);
- /* Clear the flags on disconnect event */
- if (!vbus_attach)
- notify_otg = notify_charger = false;
+ info->previous_cable = cable;
+ }
return 0;
return IRQ_HANDLED;
}
-static void axp288_extcon_enable_irq(struct axp288_extcon_info *info)
+static void axp288_extcon_enable(struct axp288_extcon_info *info)
{
- /* Unmask VBUS interrupt */
- regmap_write(info->regmap, AXP288_PWRSRC_IRQ_CFG_REG,
- PWRSRC_IRQ_CFG_MASK);
regmap_update_bits(info->regmap, AXP288_BC_GLOBAL_REG,
BC_GLOBAL_RUN, 0);
- /* Unmask the BC1.2 complete interrupts */
- regmap_write(info->regmap, AXP288_BC12_IRQ_CFG_REG, BC12_IRQ_CFG_MASK);
/* Enable the charger detection logic */
regmap_update_bits(info->regmap, AXP288_BC_GLOBAL_REG,
BC_GLOBAL_RUN, BC_GLOBAL_RUN);
{
struct axp288_extcon_info *info;
struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+ struct axp288_extcon_pdata *pdata = pdev->dev.platform_data;
int ret, i, pirq, gpio;
info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL);
info->dev = &pdev->dev;
info->regmap = axp20x->regmap;
info->regmap_irqc = axp20x->regmap_irqc;
- info->pdata = pdev->dev.platform_data;
-
- if (!info->pdata) {
- /* Try ACPI provided pdata via device properties */
- if (!device_property_present(&pdev->dev,
- "axp288_extcon_data\n"))
- dev_err(&pdev->dev, "failed to get platform data\n");
- return -ENODEV;
- }
+ info->previous_cable = EXTCON_NONE;
+ if (pdata)
+ info->gpio_mux_cntl = pdata->gpio_mux_cntl;
+
platform_set_drvdata(pdev, info);
axp288_extcon_log_rsi(info);
return ret;
}
- /* Get otg transceiver phy */
- info->otg = devm_usb_get_phy(&pdev->dev, USB_PHY_TYPE_USB2);
- if (IS_ERR(info->otg)) {
- dev_err(&pdev->dev, "failed to get otg transceiver\n");
- return PTR_ERR(info->otg);
- }
-
/* Set up gpio control for USB Mux */
- if (info->pdata->gpio_mux_cntl) {
- gpio = desc_to_gpio(info->pdata->gpio_mux_cntl);
+ if (info->gpio_mux_cntl) {
+ gpio = desc_to_gpio(info->gpio_mux_cntl);
ret = devm_gpio_request(&pdev->dev, gpio, "USB_MUX");
if (ret < 0) {
dev_err(&pdev->dev,
"failed to request the gpio=%d\n", gpio);
return ret;
}
- gpiod_direction_output(info->pdata->gpio_mux_cntl,
+ gpiod_direction_output(info->gpio_mux_cntl,
EXTCON_GPIO_MUX_SEL_PMIC);
}
}
}
- /* Enable interrupts */
- axp288_extcon_enable_irq(info);
+ /* Start charger cable type detection */
+ axp288_extcon_enable(info);
return 0;
}
+static const struct platform_device_id axp288_extcon_table[] = {
+ { .name = "axp288_extcon" },
+ {},
+};
+MODULE_DEVICE_TABLE(platform, axp288_extcon_table);
+
static struct platform_driver axp288_extcon_driver = {
.probe = axp288_extcon_probe,
+ .id_table = axp288_extcon_table,
.driver = {
.name = "axp288_extcon",
},
projects / karo-tx-linux.git / blobdiff