/*
- * linux/drivers/ide/ide-tape.c Version 1.19 Nov, 2003
- *
- * Copyright (C) 1995 - 1999 Gadi Oxman <gadio@netvision.net.il>
+ * IDE ATAPI streaming tape driver.
*
- * $Header$
+ * Copyright (C) 1995-1999 Gadi Oxman <gadio@netvision.net.il>
+ * Copyright (C) 2003-2005 Bartlomiej Zolnierkiewicz
*
* This driver was constructed as a student project in the software laboratory
* of the faculty of electrical engineering in the Technion - Israel's
*
* It is hereby placed under the terms of the GNU general public license.
* (See linux/COPYING).
- */
-
-/*
- * IDE ATAPI streaming tape driver.
- *
- * This driver is a part of the Linux ide driver and works in co-operation
- * with linux/drivers/block/ide.c.
- *
- * The driver, in co-operation with ide.c, basically traverses the
- * request-list for the block device interface. The character device
- * interface, on the other hand, creates new requests, adds them
- * to the request-list of the block device, and waits for their completion.
- *
- * Pipelined operation mode is now supported on both reads and writes.
- *
- * The block device major and minor numbers are determined from the
- * tape's relative position in the ide interfaces, as explained in ide.c.
- *
- * The character device interface consists of the following devices:
- *
- * ht0 major 37, minor 0 first IDE tape, rewind on close.
- * ht1 major 37, minor 1 second IDE tape, rewind on close.
- * ...
- * nht0 major 37, minor 128 first IDE tape, no rewind on close.
- * nht1 major 37, minor 129 second IDE tape, no rewind on close.
- * ...
- *
- * Run linux/scripts/MAKEDEV.ide to create the above entries.
- *
- * The general magnetic tape commands compatible interface, as defined by
- * include/linux/mtio.h, is accessible through the character device.
- *
- * General ide driver configuration options, such as the interrupt-unmask
- * flag, can be configured by issuing an ioctl to the block device interface,
- * as any other ide device.
- *
- * Our own ide-tape ioctl's can be issued to either the block device or
- * the character device interface.
- *
- * Maximal throughput with minimal bus load will usually be achieved in the
- * following scenario:
- *
- * 1. ide-tape is operating in the pipelined operation mode.
- * 2. No buffering is performed by the user backup program.
- *
- * Testing was done with a 2 GB CONNER CTMA 4000 IDE ATAPI Streaming Tape Drive.
- *
- * Ver 0.1 Nov 1 95 Pre-working code :-)
- * Ver 0.2 Nov 23 95 A short backup (few megabytes) and restore procedure
- * was successful ! (Using tar cvf ... on the block
- * device interface).
- * A longer backup resulted in major swapping, bad
- * overall Linux performance and eventually failed as
- * we received non serial read-ahead requests from the
- * buffer cache.
- * Ver 0.3 Nov 28 95 Long backups are now possible, thanks to the
- * character device interface. Linux's responsiveness
- * and performance doesn't seem to be much affected
- * from the background backup procedure.
- * Some general mtio.h magnetic tape operations are
- * now supported by our character device. As a result,
- * popular tape utilities are starting to work with
- * ide tapes :-)
- * The following configurations were tested:
- * 1. An IDE ATAPI TAPE shares the same interface
- * and irq with an IDE ATAPI CDROM.
- * 2. An IDE ATAPI TAPE shares the same interface
- * and irq with a normal IDE disk.
- * Both configurations seemed to work just fine !
- * However, to be on the safe side, it is meanwhile
- * recommended to give the IDE TAPE its own interface
- * and irq.
- * The one thing which needs to be done here is to
- * add a "request postpone" feature to ide.c,
- * so that we won't have to wait for the tape to finish
- * performing a long media access (DSC) request (such
- * as a rewind) before we can access the other device
- * on the same interface. This effect doesn't disturb
- * normal operation most of the time because read/write
- * requests are relatively fast, and once we are
- * performing one tape r/w request, a lot of requests
- * from the other device can be queued and ide.c will
- * service all of them after this single tape request.
- * Ver 1.0 Dec 11 95 Integrated into Linux 1.3.46 development tree.
- * On each read / write request, we now ask the drive
- * if we can transfer a constant number of bytes
- * (a parameter of the drive) only to its buffers,
- * without causing actual media access. If we can't,
- * we just wait until we can by polling the DSC bit.
- * This ensures that while we are not transferring
- * more bytes than the constant referred to above, the
- * interrupt latency will not become too high and
- * we won't cause an interrupt timeout, as happened
- * occasionally in the previous version.
- * While polling for DSC, the current request is
- * postponed and ide.c is free to handle requests from
- * the other device. This is handled transparently to
- * ide.c. The hwgroup locking method which was used
- * in the previous version was removed.
- * Use of new general features which are provided by
- * ide.c for use with atapi devices.
- * (Programming done by Mark Lord)
- * Few potential bug fixes (Again, suggested by Mark)
- * Single character device data transfers are now
- * not limited in size, as they were before.
- * We are asking the tape about its recommended
- * transfer unit and send a larger data transfer
- * as several transfers of the above size.
- * For best results, use an integral number of this
- * basic unit (which is shown during driver
- * initialization). I will soon add an ioctl to get
- * this important parameter.
- * Our data transfer buffer is allocated on startup,
- * rather than before each data transfer. This should
- * ensure that we will indeed have a data buffer.
- * Ver 1.1 Dec 14 95 Fixed random problems which occurred when the tape
- * shared an interface with another device.
- * (poll_for_dsc was a complete mess).
- * Removed some old (non-active) code which had
- * to do with supporting buffer cache originated
- * requests.
- * The block device interface can now be opened, so
- * that general ide driver features like the unmask
- * interrupts flag can be selected with an ioctl.
- * This is the only use of the block device interface.
- * New fast pipelined operation mode (currently only on
- * writes). When using the pipelined mode, the
- * throughput can potentially reach the maximum
- * tape supported throughput, regardless of the
- * user backup program. On my tape drive, it sometimes
- * boosted performance by a factor of 2. Pipelined
- * mode is enabled by default, but since it has a few
- * downfalls as well, you may want to disable it.
- * A short explanation of the pipelined operation mode
- * is available below.
- * Ver 1.2 Jan 1 96 Eliminated pipelined mode race condition.
- * Added pipeline read mode. As a result, restores
- * are now as fast as backups.
- * Optimized shared interface behavior. The new behavior
- * typically results in better IDE bus efficiency and
- * higher tape throughput.
- * Pre-calculation of the expected read/write request
- * service time, based on the tape's parameters. In
- * the pipelined operation mode, this allows us to
- * adjust our polling frequency to a much lower value,
- * and thus to dramatically reduce our load on Linux,
- * without any decrease in performance.
- * Implemented additional mtio.h operations.
- * The recommended user block size is returned by
- * the MTIOCGET ioctl.
- * Additional minor changes.
- * Ver 1.3 Feb 9 96 Fixed pipelined read mode bug which prevented the
- * use of some block sizes during a restore procedure.
- * The character device interface will now present a
- * continuous view of the media - any mix of block sizes
- * during a backup/restore procedure is supported. The
- * driver will buffer the requests internally and
- * convert them to the tape's recommended transfer
- * unit, making performance almost independent of the
- * chosen user block size.
- * Some improvements in error recovery.
- * By cooperating with ide-dma.c, bus mastering DMA can
- * now sometimes be used with IDE tape drives as well.
- * Bus mastering DMA has the potential to dramatically
- * reduce the CPU's overhead when accessing the device,
- * and can be enabled by using hdparm -d1 on the tape's
- * block device interface. For more info, read the
- * comments in ide-dma.c.
- * Ver 1.4 Mar 13 96 Fixed serialize support.
- * Ver 1.5 Apr 12 96 Fixed shared interface operation, broken in 1.3.85.
- * Fixed pipelined read mode inefficiency.
- * Fixed nasty null dereferencing bug.
- * Ver 1.6 Aug 16 96 Fixed FPU usage in the driver.
- * Fixed end of media bug.
- * Ver 1.7 Sep 10 96 Minor changes for the CONNER CTT8000-A model.
- * Ver 1.8 Sep 26 96 Attempt to find a better balance between good
- * interactive response and high system throughput.
- * Ver 1.9 Nov 5 96 Automatically cross encountered filemarks rather
- * than requiring an explicit FSF command.
- * Abort pending requests at end of media.
- * MTTELL was sometimes returning incorrect results.
- * Return the real block size in the MTIOCGET ioctl.
- * Some error recovery bug fixes.
- * Ver 1.10 Nov 5 96 Major reorganization.
- * Reduced CPU overhead a bit by eliminating internal
- * bounce buffers.
- * Added module support.
- * Added multiple tape drives support.
- * Added partition support.
- * Rewrote DSC handling.
- * Some portability fixes.
- * Removed ide-tape.h.
- * Additional minor changes.
- * Ver 1.11 Dec 2 96 Bug fix in previous DSC timeout handling.
- * Use ide_stall_queue() for DSC overlap.
- * Use the maximum speed rather than the current speed
- * to compute the request service time.
- * Ver 1.12 Dec 7 97 Fix random memory overwriting and/or last block data
- * corruption, which could occur if the total number
- * of bytes written to the tape was not an integral
- * number of tape blocks.
- * Add support for INTERRUPT DRQ devices.
- * Ver 1.13 Jan 2 98 Add "speed == 0" work-around for HP COLORADO 5GB
- * Ver 1.14 Dec 30 98 Partial fixes for the Sony/AIWA tape drives.
- * Replace cli()/sti() with hwgroup spinlocks.
- * Ver 1.15 Mar 25 99 Fix SMP race condition by replacing hwgroup
- * spinlock with private per-tape spinlock.
- * Ver 1.16 Sep 1 99 Add OnStream tape support.
- * Abort read pipeline on EOD.
- * Wait for the tape to become ready in case it returns
- * "in the process of becoming ready" on open().
- * Fix zero padding of the last written block in
- * case the tape block size is larger than PAGE_SIZE.
- * Decrease the default disconnection time to tn.
- * Ver 1.16e Oct 3 99 Minor fixes.
- * Ver 1.16e1 Oct 13 99 Patches by Arnold Niessen,
- * niessen@iae.nl / arnold.niessen@philips.com
- * GO-1) Undefined code in idetape_read_position
- * according to Gadi's email
- * AJN-1) Minor fix asc == 11 should be asc == 0x11
- * in idetape_issue_packet_command (did effect
- * debugging output only)
- * AJN-2) Added more debugging output, and
- * added ide-tape: where missing. I would also
- * like to add tape->name where possible
- * AJN-3) Added different debug_level's
- * via /proc/ide/hdc/settings
- * "debug_level" determines amount of debugging output;
- * can be changed using /proc/ide/hdx/settings
- * 0 : almost no debugging output
- * 1 : 0+output errors only
- * 2 : 1+output all sensekey/asc
- * 3 : 2+follow all chrdev related procedures
- * 4 : 3+follow all procedures
- * 5 : 4+include pc_stack rq_stack info
- * 6 : 5+USE_COUNT updates
- * AJN-4) Fixed timeout for retension in idetape_queue_pc_tail
- * from 5 to 10 minutes
- * AJN-5) Changed maximum number of blocks to skip when
- * reading tapes with multiple consecutive write
- * errors from 100 to 1000 in idetape_get_logical_blk
- * Proposed changes to code:
- * 1) output "logical_blk_num" via /proc
- * 2) output "current_operation" via /proc
- * 3) Either solve or document the fact that `mt rewind' is
- * required after reading from /dev/nhtx to be
- * able to rmmod the idetape module;
- * Also, sometimes an application finishes but the
- * device remains `busy' for some time. Same cause ?
- * Proposed changes to release-notes:
- * 4) write a simple `quickstart' section in the
- * release notes; I volunteer if you don't want to
- * 5) include a pointer to video4linux in the doc
- * to stimulate video applications
- * 6) release notes lines 331 and 362: explain what happens
- * if the application data rate is higher than 1100 KB/s;
- * similar approach to lower-than-500 kB/s ?
- * 7) 6.6 Comparison; wouldn't it be better to allow different
- * strategies for read and write ?
- * Wouldn't it be better to control the tape buffer
- * contents instead of the bandwidth ?
- * 8) line 536: replace will by would (if I understand
- * this section correctly, a hypothetical and unwanted situation
- * is being described)
- * Ver 1.16f Dec 15 99 Change place of the secondary OnStream header frames.
- * Ver 1.17 Nov 2000 / Jan 2001 Marcel Mol, marcel@mesa.nl
- * - Add idetape_onstream_mode_sense_tape_parameter_page
- * function to get tape capacity in frames: tape->capacity.
- * - Add support for DI-50 drives( or any DI- drive).
- * - 'workaround' for read error/blank block around block 3000.
- * - Implement Early warning for end of media for Onstream.
- * - Cosmetic code changes for readability.
- * - Idetape_position_tape should not use SKIP bit during
- * Onstream read recovery.
- * - Add capacity, logical_blk_num and first/last_frame_position
- * to /proc/ide/hd?/settings.
- * - Module use count was gone in the Linux 2.4 driver.
- * Ver 1.17a Apr 2001 Willem Riede osst@riede.org
- * - Get drive's actual block size from mode sense block descriptor
- * - Limit size of pipeline
- * Ver 1.17b Oct 2002 Alan Stern <stern@rowland.harvard.edu>
- * Changed IDETAPE_MIN_PIPELINE_STAGES to 1 and actually used
- * it in the code!
- * Actually removed aborted stages in idetape_abort_pipeline
- * instead of just changing the command code.
- * Made the transfer byte count for Request Sense equal to the
- * actual length of the data transfer.
- * Changed handling of partial data transfers: they do not
- * cause DMA errors.
- * Moved initiation of DMA transfers to the correct place.
- * Removed reference to unallocated memory.
- * Made __idetape_discard_read_pipeline return the number of
- * sectors skipped, not the number of stages.
- * Replaced errant kfree() calls with __idetape_kfree_stage().
- * Fixed off-by-one error in testing the pipeline length.
- * Fixed handling of filemarks in the read pipeline.
- * Small code optimization for MTBSF and MTBSFM ioctls.
- * Don't try to unlock the door during device close if is
- * already unlocked!
- * Cosmetic fixes to miscellaneous debugging output messages.
- * Set the minimum /proc/ide/hd?/settings values for "pipeline",
- * "pipeline_min", and "pipeline_max" to 1.
- *
- * Here are some words from the first releases of hd.c, which are quoted
- * in ide.c and apply here as well:
- *
- * | Special care is recommended. Have Fun!
*
- */
-
-/*
- * An overview of the pipelined operation mode.
- *
- * In the pipelined write mode, we will usually just add requests to our
- * pipeline and return immediately, before we even start to service them. The
- * user program will then have enough time to prepare the next request while
- * we are still busy servicing previous requests. In the pipelined read mode,
- * the situation is similar - we add read-ahead requests into the pipeline,
- * before the user even requested them.
- *
- * The pipeline can be viewed as a "safety net" which will be activated when
- * the system load is high and prevents the user backup program from keeping up
- * with the current tape speed. At this point, the pipeline will get
- * shorter and shorter but the tape will still be streaming at the same speed.
- * Assuming we have enough pipeline stages, the system load will hopefully
- * decrease before the pipeline is completely empty, and the backup program
- * will be able to "catch up" and refill the pipeline again.
- *
- * When using the pipelined mode, it would be best to disable any type of
- * buffering done by the user program, as ide-tape already provides all the
- * benefits in the kernel, where it can be done in a more efficient way.
- * As we will usually not block the user program on a request, the most
- * efficient user code will then be a simple read-write-read-... cycle.
- * Any additional logic will usually just slow down the backup process.
- *
- * Using the pipelined mode, I get a constant over 400 KBps throughput,
- * which seems to be the maximum throughput supported by my tape.
- *
- * However, there are some downfalls:
- *
- * 1. We use memory (for data buffers) in proportional to the number
- * of pipeline stages (each stage is about 26 KB with my tape).
- * 2. In the pipelined write mode, we cheat and postpone error codes
- * to the user task. In read mode, the actual tape position
- * will be a bit further than the last requested block.
- *
- * Concerning (1):
- *
- * 1. We allocate stages dynamically only when we need them. When
- * we don't need them, we don't consume additional memory. In
- * case we can't allocate stages, we just manage without them
- * (at the expense of decreased throughput) so when Linux is
- * tight in memory, we will not pose additional difficulties.
- *
- * 2. The maximum number of stages (which is, in fact, the maximum
- * amount of memory) which we allocate is limited by the compile
- * time parameter IDETAPE_MAX_PIPELINE_STAGES.
- *
- * 3. The maximum number of stages is a controlled parameter - We
- * don't start from the user defined maximum number of stages
- * but from the lower IDETAPE_MIN_PIPELINE_STAGES (again, we
- * will not even allocate this amount of stages if the user
- * program can't handle the speed). We then implement a feedback
- * loop which checks if the pipeline is empty, and if it is, we
- * increase the maximum number of stages as necessary until we
- * reach the optimum value which just manages to keep the tape
- * busy with minimum allocated memory or until we reach
- * IDETAPE_MAX_PIPELINE_STAGES.
- *
- * Concerning (2):
- *
- * In pipelined write mode, ide-tape can not return accurate error codes
- * to the user program since we usually just add the request to the
- * pipeline without waiting for it to be serviced. In case an error
- * occurs, I will report it on the next user request.
- *
- * In the pipelined read mode, subsequent read requests or forward
- * filemark spacing will perform correctly, as we preserve all blocks
- * and filemarks which we encountered during our excess read-ahead.
- *
- * For accurate tape positioning and error reporting, disabling
- * pipelined mode might be the best option.
- *
- * You can enable/disable/tune the pipelined operation mode by adjusting
- * the compile time parameters below.
- */
-
-/*
- * Possible improvements.
- *
- * 1. Support for the ATAPI overlap protocol.
- *
- * In order to maximize bus throughput, we currently use the DSC
- * overlap method which enables ide.c to service requests from the
- * other device while the tape is busy executing a command. The
- * DSC overlap method involves polling the tape's status register
- * for the DSC bit, and servicing the other device while the tape
- * isn't ready.
- *
- * In the current QIC development standard (December 1995),
- * it is recommended that new tape drives will *in addition*
- * implement the ATAPI overlap protocol, which is used for the
- * same purpose - efficient use of the IDE bus, but is interrupt
- * driven and thus has much less CPU overhead.
- *
- * ATAPI overlap is likely to be supported in most new ATAPI
- * devices, including new ATAPI cdroms, and thus provides us
- * a method by which we can achieve higher throughput when
- * sharing a (fast) ATA-2 disk with any (slow) new ATAPI device.
+ * For a historical changelog see
+ * Documentation/ide/ChangeLog.ide-tape.1995-2002
*/
#define IDETAPE_VERSION "1.19"
/*************************** End of tunable parameters ***********************/
-/*
- * Debugging/Performance analysis
- *
- * I/O trace support
- */
-#define USE_IOTRACE 0
-#if USE_IOTRACE
-#define IO_IDETAPE_FIFO 500
-#endif
-
/*
* Read/Write error simulation
*/
struct idetape_stage_s *next; /* Pointer to the next stage */
} idetape_stage_t;
-/*
- * REQUEST SENSE packet command result - Data Format.
- */
-typedef struct {
- unsigned error_code :7; /* Current of deferred errors */
- unsigned valid :1; /* The information field conforms to QIC-157C */
- __u8 reserved1 :8; /* Segment Number - Reserved */
- unsigned sense_key :4; /* Sense Key */
- unsigned reserved2_4 :1; /* Reserved */
- unsigned ili :1; /* Incorrect Length Indicator */
- unsigned eom :1; /* End Of Medium */
- unsigned filemark :1; /* Filemark */
- __u32 information __attribute__ ((packed));
- __u8 asl; /* Additional sense length (n-7) */
- __u32 command_specific; /* Additional command specific information */
- __u8 asc; /* Additional Sense Code */
- __u8 ascq; /* Additional Sense Code Qualifier */
- __u8 replaceable_unit_code; /* Field Replaceable Unit Code */
- unsigned sk_specific1 :7; /* Sense Key Specific */
- unsigned sksv :1; /* Sense Key Specific information is valid */
- __u8 sk_specific2; /* Sense Key Specific */
- __u8 sk_specific3; /* Sense Key Specific */
- __u8 pad[2]; /* Padding to 20 bytes */
-} idetape_request_sense_result_t;
-
-
/*
* Most of our global data which we need to save even as we leave the
* driver due to an interrupt or a timer event is stored in a variable
int avg_size;
int avg_speed;
- /* last sense information */
- idetape_request_sense_result_t sense;
-
char vendor_id[10];
char product_id[18];
char firmware_revision[6];
#define IDETAPE_BLOCK_SIZE_PAGE 0x30
#define IDETAPE_BUFFER_FILLING_PAGE 0x33
-/*
- * Mode Parameter Header for the MODE SENSE packet command
- */
-typedef struct {
- __u8 mode_data_length; /* Length of the following data transfer */
- __u8 medium_type; /* Medium Type */
- __u8 dsp; /* Device Specific Parameter */
- __u8 bdl; /* Block Descriptor Length */
-#if 0
- /* data transfer page */
- __u8 page_code :6;
- __u8 reserved0_6 :1;
- __u8 ps :1; /* parameters saveable */
- __u8 page_length; /* page Length == 0x02 */
- __u8 reserved2;
- __u8 read32k :1; /* 32k blk size (data only) */
- __u8 read32k5 :1; /* 32.5k blk size (data&AUX) */
- __u8 reserved3_23 :2;
- __u8 write32k :1; /* 32k blk size (data only) */
- __u8 write32k5 :1; /* 32.5k blk size (data&AUX) */
- __u8 reserved3_6 :1;
- __u8 streaming :1; /* streaming mode enable */
-#endif
-} idetape_mode_parameter_header_t;
-
/*
* Mode Parameter Block Descriptor the MODE SENSE packet command
*
}
/*
- * idetape_analyze_error is called on each failed packet command retry
- * to analyze the request sense. We currently do not utilize this
- * information.
+ * called on each failed packet command retry to analyze the request sense. We
+ * currently do not utilize this information.
*/
-static void idetape_analyze_error (ide_drive_t *drive, idetape_request_sense_result_t *result)
+static void idetape_analyze_error(ide_drive_t *drive, u8 *sense)
{
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t *pc = tape->failed_pc;
- tape->sense = *result;
- tape->sense_key = result->sense_key;
- tape->asc = result->asc;
- tape->ascq = result->ascq;
+ tape->sense_key = sense[2] & 0xF;
+ tape->asc = sense[12];
+ tape->ascq = sense[13];
#if IDETAPE_DEBUG_LOG
/*
- * Without debugging, we only log an error if we decided to
- * give up retrying.
+ * Without debugging, we only log an error if we decided to give up
+ * retrying.
*/
if (tape->debug_level >= 1)
printk(KERN_INFO "ide-tape: pc = %x, sense key = %x, "
"asc = %x, ascq = %x\n",
- pc->c[0], result->sense_key,
- result->asc, result->ascq);
+ pc->c[0], tape->sense_key,
+ tape->asc, tape->ascq);
#endif /* IDETAPE_DEBUG_LOG */
- /*
- * Correct pc->actually_transferred by asking the tape.
- */
+ /* Correct pc->actually_transferred by asking the tape. */
if (test_bit(PC_DMA_ERROR, &pc->flags)) {
- pc->actually_transferred = pc->request_transfer - tape->tape_block_size * ntohl(get_unaligned(&result->information));
+ pc->actually_transferred = pc->request_transfer -
+ tape->tape_block_size *
+ ntohl(get_unaligned((u32 *)&sense[3]));
idetape_update_buffers(pc);
}
* (i.e. Seagate STT3401A Travan) don't support 0-length read/writes.
*/
if ((pc->c[0] == IDETAPE_READ_CMD || pc->c[0] == IDETAPE_WRITE_CMD)
- && pc->c[4] == 0 && pc->c[3] == 0 && pc->c[2] == 0) { /* length==0 */
- if (result->sense_key == 5) {
+ /* length == 0 */
+ && pc->c[4] == 0 && pc->c[3] == 0 && pc->c[2] == 0) {
+ if (tape->sense_key == 5) {
/* don't report an error, everything's ok */
pc->error = 0;
/* don't retry read/write */
set_bit(PC_ABORT, &pc->flags);
}
}
- if (pc->c[0] == IDETAPE_READ_CMD && result->filemark) {
+ if (pc->c[0] == IDETAPE_READ_CMD && (sense[2] & 0x80)) {
pc->error = IDETAPE_ERROR_FILEMARK;
set_bit(PC_ABORT, &pc->flags);
}
if (pc->c[0] == IDETAPE_WRITE_CMD) {
- if (result->eom ||
- (result->sense_key == 0xd && result->asc == 0x0 &&
- result->ascq == 0x2)) {
+ if ((sense[2] & 0x40) || (tape->sense_key == 0xd
+ && tape->asc == 0x0 && tape->ascq == 0x2)) {
pc->error = IDETAPE_ERROR_EOD;
set_bit(PC_ABORT, &pc->flags);
}
}
if (pc->c[0] == IDETAPE_READ_CMD || pc->c[0] == IDETAPE_WRITE_CMD) {
- if (result->sense_key == 8) {
+ if (tape->sense_key == 8) {
pc->error = IDETAPE_ERROR_EOD;
set_bit(PC_ABORT, &pc->flags);
}
if (error)
tape->failed_pc = NULL;
+ if (!blk_special_request(rq)) {
+ ide_end_request(drive, uptodate, nr_sects);
+ return 0;
+ }
+
spin_lock_irqsave(&tape->spinlock, flags);
/* The request was a pipelined data transfer request */
printk(KERN_INFO "ide-tape: Reached idetape_request_sense_callback\n");
#endif /* IDETAPE_DEBUG_LOG */
if (!tape->pc->error) {
- idetape_analyze_error(drive, (idetape_request_sense_result_t *) tape->pc->buffer);
+ idetape_analyze_error(drive, tape->pc->buffer);
idetape_end_request(drive, 1, 0);
} else {
printk(KERN_ERR "ide-tape: Error in REQUEST SENSE itself - Aborting request!\n");
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t *pc;
struct request *rq;
- atapi_error_t error;
- error.all = HWIF(drive)->INB(IDE_ERROR_REG);
+ (void)drive->hwif->INB(IDE_ERROR_REG);
pc = idetape_next_pc_storage(drive);
rq = idetape_next_rq_storage(drive);
idetape_create_request_sense_cmd(pc);
{
ide_hwif_t *hwif = drive->hwif;
idetape_tape_t *tape = drive->driver_data;
- atapi_status_t status;
- atapi_bcount_t bcount;
- atapi_ireason_t ireason;
idetape_pc_t *pc = tape->pc;
-
unsigned int temp;
#if SIMULATE_ERRORS
static int error_sim_count = 0;
#endif
+ u16 bcount;
+ u8 stat, ireason;
#if IDETAPE_DEBUG_LOG
if (tape->debug_level >= 4)
#endif /* IDETAPE_DEBUG_LOG */
/* Clear the interrupt */
- status.all = HWIF(drive)->INB(IDE_STATUS_REG);
+ stat = hwif->INB(IDE_STATUS_REG);
if (test_bit(PC_DMA_IN_PROGRESS, &pc->flags)) {
- if (HWIF(drive)->ide_dma_end(drive) || status.b.check) {
+ if (hwif->ide_dma_end(drive) || (stat & ERR_STAT)) {
/*
* A DMA error is sometimes expected. For example,
* if the tape is crossing a filemark during a
}
/* No more interrupts */
- if (!status.b.drq) {
+ if ((stat & DRQ_STAT) == 0) {
#if IDETAPE_DEBUG_LOG
if (tape->debug_level >= 2)
printk(KERN_INFO "ide-tape: Packet command completed, %d bytes transferred\n", pc->actually_transferred);
(++error_sim_count % 100) == 0) {
printk(KERN_INFO "ide-tape: %s: simulating error\n",
tape->name);
- status.b.check = 1;
+ stat |= ERR_STAT;
}
#endif
- if (status.b.check && pc->c[0] == IDETAPE_REQUEST_SENSE_CMD)
- status.b.check = 0;
- if (status.b.check || test_bit(PC_DMA_ERROR, &pc->flags)) { /* Error detected */
+ if ((stat & ERR_STAT) && pc->c[0] == IDETAPE_REQUEST_SENSE_CMD)
+ stat &= ~ERR_STAT;
+ if ((stat & ERR_STAT) || test_bit(PC_DMA_ERROR, &pc->flags)) {
+ /* Error detected */
#if IDETAPE_DEBUG_LOG
if (tape->debug_level >= 1)
printk(KERN_INFO "ide-tape: %s: I/O error\n",
}
pc->error = 0;
if (test_bit(PC_WAIT_FOR_DSC, &pc->flags) &&
- !status.b.dsc) {
+ (stat & SEEK_STAT) == 0) {
/* Media access command */
tape->dsc_polling_start = jiffies;
tape->dsc_polling_frequency = IDETAPE_DSC_MA_FAST;
return ide_do_reset(drive);
}
/* Get the number of bytes to transfer on this interrupt. */
- bcount.b.high = hwif->INB(IDE_BCOUNTH_REG);
- bcount.b.low = hwif->INB(IDE_BCOUNTL_REG);
+ bcount = (hwif->INB(IDE_BCOUNTH_REG) << 8) |
+ hwif->INB(IDE_BCOUNTL_REG);
- ireason.all = hwif->INB(IDE_IREASON_REG);
+ ireason = hwif->INB(IDE_IREASON_REG);
- if (ireason.b.cod) {
+ if (ireason & CD) {
printk(KERN_ERR "ide-tape: CoD != 0 in idetape_pc_intr\n");
return ide_do_reset(drive);
}
- if (ireason.b.io == test_bit(PC_WRITING, &pc->flags)) {
+ if (((ireason & IO) == IO) == test_bit(PC_WRITING, &pc->flags)) {
/* Hopefully, we will never get here */
printk(KERN_ERR "ide-tape: We wanted to %s, ",
- ireason.b.io ? "Write":"Read");
+ (ireason & IO) ? "Write" : "Read");
printk(KERN_ERR "ide-tape: but the tape wants us to %s !\n",
- ireason.b.io ? "Read":"Write");
+ (ireason & IO) ? "Read" : "Write");
return ide_do_reset(drive);
}
if (!test_bit(PC_WRITING, &pc->flags)) {
/* Reading - Check that we have enough space */
- temp = pc->actually_transferred + bcount.all;
+ temp = pc->actually_transferred + bcount;
if (temp > pc->request_transfer) {
if (temp > pc->buffer_size) {
printk(KERN_ERR "ide-tape: The tape wants to send us more data than expected - discarding data\n");
- idetape_discard_data(drive, bcount.all);
+ idetape_discard_data(drive, bcount);
ide_set_handler(drive, &idetape_pc_intr, IDETAPE_WAIT_CMD, NULL);
return ide_started;
}
}
if (test_bit(PC_WRITING, &pc->flags)) {
if (pc->bh != NULL)
- idetape_output_buffers(drive, pc, bcount.all);
+ idetape_output_buffers(drive, pc, bcount);
else
/* Write the current buffer */
- HWIF(drive)->atapi_output_bytes(drive, pc->current_position, bcount.all);
+ hwif->atapi_output_bytes(drive, pc->current_position,
+ bcount);
} else {
if (pc->bh != NULL)
- idetape_input_buffers(drive, pc, bcount.all);
+ idetape_input_buffers(drive, pc, bcount);
else
/* Read the current buffer */
- HWIF(drive)->atapi_input_bytes(drive, pc->current_position, bcount.all);
+ hwif->atapi_input_bytes(drive, pc->current_position,
+ bcount);
}
/* Update the current position */
- pc->actually_transferred += bcount.all;
- pc->current_position += bcount.all;
+ pc->actually_transferred += bcount;
+ pc->current_position += bcount;
#if IDETAPE_DEBUG_LOG
if (tape->debug_level >= 2)
- printk(KERN_INFO "ide-tape: [cmd %x] transferred %d bytes on that interrupt\n", pc->c[0], bcount.all);
+ printk(KERN_INFO "ide-tape: [cmd %x] transferred %d bytes "
+ "on that interrupt\n", pc->c[0], bcount);
#endif
/* And set the interrupt handler again */
ide_set_handler(drive, &idetape_pc_intr, IDETAPE_WAIT_CMD, NULL);
ide_hwif_t *hwif = drive->hwif;
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t *pc = tape->pc;
- atapi_ireason_t ireason;
int retries = 100;
ide_startstop_t startstop;
+ u8 ireason;
if (ide_wait_stat(&startstop,drive,DRQ_STAT,BUSY_STAT,WAIT_READY)) {
printk(KERN_ERR "ide-tape: Strange, packet command initiated yet DRQ isn't asserted\n");
return startstop;
}
- ireason.all = hwif->INB(IDE_IREASON_REG);
- while (retries-- && (!ireason.b.cod || ireason.b.io)) {
+ ireason = hwif->INB(IDE_IREASON_REG);
+ while (retries-- && ((ireason & CD) == 0 || (ireason & IO))) {
printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while issuing "
"a packet command, retrying\n");
udelay(100);
- ireason.all = hwif->INB(IDE_IREASON_REG);
+ ireason = hwif->INB(IDE_IREASON_REG);
if (retries == 0) {
printk(KERN_ERR "ide-tape: (IO,CoD != (0,1) while "
"issuing a packet command, ignoring\n");
- ireason.b.cod = 1;
- ireason.b.io = 0;
+ ireason |= CD;
+ ireason &= ~IO;
}
}
- if (!ireason.b.cod || ireason.b.io) {
+ if ((ireason & CD) == 0 || (ireason & IO)) {
printk(KERN_ERR "ide-tape: (IO,CoD) != (0,1) while issuing "
"a packet command\n");
return ide_do_reset(drive);
{
ide_hwif_t *hwif = drive->hwif;
idetape_tape_t *tape = drive->driver_data;
- atapi_bcount_t bcount;
int dma_ok = 0;
+ u16 bcount;
#if IDETAPE_DEBUG_BUGS
if (tape->pc->c[0] == IDETAPE_REQUEST_SENSE_CMD &&
pc->actually_transferred = 0;
pc->current_position = pc->buffer;
/* Request to transfer the entire buffer at once */
- bcount.all = pc->request_transfer;
+ bcount = pc->request_transfer;
if (test_and_clear_bit(PC_DMA_ERROR, &pc->flags)) {
printk(KERN_WARNING "ide-tape: DMA disabled, "
if (test_bit(PC_DMA_RECOMMENDED, &pc->flags) && drive->using_dma)
dma_ok = !hwif->dma_setup(drive);
- if (IDE_CONTROL_REG)
- hwif->OUTB(drive->ctl, IDE_CONTROL_REG);
- hwif->OUTB(dma_ok ? 1 : 0, IDE_FEATURE_REG); /* Use PIO/DMA */
- hwif->OUTB(bcount.b.high, IDE_BCOUNTH_REG);
- hwif->OUTB(bcount.b.low, IDE_BCOUNTL_REG);
- hwif->OUTB(drive->select.all, IDE_SELECT_REG);
+ ide_pktcmd_tf_load(drive, IDE_TFLAG_NO_SELECT_MASK |
+ IDE_TFLAG_OUT_DEVICE, bcount, dma_ok);
+
if (dma_ok) /* Will begin DMA later */
set_bit(PC_DMA_IN_PROGRESS, &pc->flags);
if (test_bit(IDETAPE_DRQ_INTERRUPT, &tape->flags)) {
- ide_set_handler(drive, &idetape_transfer_pc, IDETAPE_WAIT_CMD, NULL);
- hwif->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG);
+ ide_execute_command(drive, WIN_PACKETCMD, &idetape_transfer_pc,
+ IDETAPE_WAIT_CMD, NULL);
return ide_started;
} else {
hwif->OUTB(WIN_PACKETCMD, IDE_COMMAND_REG);
{
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t *pc = tape->pc;
- atapi_status_t status;
+ u8 stat;
- status.all = HWIF(drive)->INB(IDE_STATUS_REG);
- if (status.b.dsc) {
- if (status.b.check) {
+ stat = drive->hwif->INB(IDE_STATUS_REG);
+ if (stat & SEEK_STAT) {
+ if (stat & ERR_STAT) {
/* Error detected */
if (pc->c[0] != IDETAPE_TEST_UNIT_READY_CMD)
printk(KERN_ERR "ide-tape: %s: I/O error, ",
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t *pc = NULL;
struct request *postponed_rq = tape->postponed_rq;
- atapi_status_t status;
+ u8 stat;
#if IDETAPE_DEBUG_LOG
-#if 0
- if (tape->debug_level >= 5)
- printk(KERN_INFO "ide-tape: %d, "
- "dev: %s, cmd: %ld, errors: %d\n",
- rq->rq_disk->disk_name, rq->cmd[0], rq->errors);
-#endif
if (tape->debug_level >= 2)
printk(KERN_INFO "ide-tape: sector: %ld, "
"nr_sectors: %ld, current_nr_sectors: %d\n",
* If the tape is still busy, postpone our request and service
* the other device meanwhile.
*/
- status.all = HWIF(drive)->INB(IDE_STATUS_REG);
+ stat = drive->hwif->INB(IDE_STATUS_REG);
if (!drive->dsc_overlap && !(rq->cmd[0] & REQ_IDETAPE_PC2))
set_bit(IDETAPE_IGNORE_DSC, &tape->flags);
tape->insert_speed = tape->insert_size / 1024 * HZ / (jiffies - tape->insert_time);
calculate_speeds(drive);
if (!test_and_clear_bit(IDETAPE_IGNORE_DSC, &tape->flags) &&
- !status.b.dsc) {
+ (stat & SEEK_STAT) == 0) {
if (postponed_rq == NULL) {
tape->dsc_polling_start = jiffies;
tape->dsc_polling_frequency = tape->best_dsc_rw_frequency;
}
if (rq->cmd[0] & REQ_IDETAPE_READ) {
tape->buffer_head++;
-#if USE_IOTRACE
- IO_trace(IO_IDETAPE_FIFO, tape->pipeline_head, tape->buffer_head, tape->tape_head, tape->minor);
-#endif
tape->postpone_cnt = 0;
pc = idetape_next_pc_storage(drive);
idetape_create_read_cmd(tape, pc, rq->current_nr_sectors, (struct idetape_bh *)rq->special);
}
if (rq->cmd[0] & REQ_IDETAPE_WRITE) {
tape->buffer_head++;
-#if USE_IOTRACE
- IO_trace(IO_IDETAPE_FIFO, tape->pipeline_head, tape->buffer_head, tape->tape_head, tape->minor);
-#endif
tape->postpone_cnt = 0;
pc = idetape_next_pc_storage(drive);
idetape_create_write_cmd(tape, pc, rq->current_nr_sectors, (struct idetape_bh *)rq->special);
pc->callback = &idetape_pc_callback;
}
-#if 0
-static void idetape_create_mode_select_cmd (idetape_pc_t *pc, int length)
-{
- idetape_init_pc(pc);
- set_bit(PC_WRITING, &pc->flags);
- pc->c[0] = IDETAPE_MODE_SELECT_CMD;
- pc->c[1] = 0x10;
- put_unaligned(htons(length), (unsigned short *) &pc->c[3]);
- pc->request_transfer = 255;
- pc->callback = &idetape_pc_callback;
-}
-#endif
-
static void idetape_create_erase_cmd (idetape_pc_t *pc)
{
idetape_init_pc(pc);
idetape_switch_buffers(tape, new_stage);
idetape_add_stage_tail(drive, new_stage);
tape->pipeline_head++;
-#if USE_IOTRACE
- IO_trace(IO_IDETAPE_FIFO, tape->pipeline_head, tape->buffer_head, tape->tape_head, tape->minor);
-#endif
calculate_speeds(drive);
/*
idetape_remove_stage_head(drive);
spin_unlock_irqrestore(&tape->spinlock, flags);
tape->pipeline_head++;
-#if USE_IOTRACE
- IO_trace(IO_IDETAPE_FIFO, tape->pipeline_head, tape->buffer_head, tape->tape_head, tape->minor);
-#endif
calculate_speeds(drive);
}
#if IDETAPE_DEBUG_BUGS
{
struct idetape_id_gcw gcw;
struct hd_driveid *id = drive->id;
-#if IDETAPE_DEBUG_INFO
- unsigned short mask,i;
-#endif /* IDETAPE_DEBUG_INFO */
if (drive->id_read == 0)
return 1;
case 1: printk("16 bytes\n");break;
default: printk("Reserved\n");break;
}
- printk(KERN_INFO "ide-tape: Model: %.40s\n",id->model);
- printk(KERN_INFO "ide-tape: Firmware Revision: %.8s\n",id->fw_rev);
- printk(KERN_INFO "ide-tape: Serial Number: %.20s\n",id->serial_no);
- printk(KERN_INFO "ide-tape: Write buffer size: %d bytes\n",id->buf_size*512);
- printk(KERN_INFO "ide-tape: DMA: %s",id->capability & 0x01 ? "Yes\n":"No\n");
- printk(KERN_INFO "ide-tape: LBA: %s",id->capability & 0x02 ? "Yes\n":"No\n");
- printk(KERN_INFO "ide-tape: IORDY can be disabled: %s",id->capability & 0x04 ? "Yes\n":"No\n");
- printk(KERN_INFO "ide-tape: IORDY supported: %s",id->capability & 0x08 ? "Yes\n":"Unknown\n");
- printk(KERN_INFO "ide-tape: ATAPI overlap supported: %s",id->capability & 0x20 ? "Yes\n":"No\n");
- printk(KERN_INFO "ide-tape: PIO Cycle Timing Category: %d\n",id->tPIO);
- printk(KERN_INFO "ide-tape: DMA Cycle Timing Category: %d\n",id->tDMA);
- printk(KERN_INFO "ide-tape: Single Word DMA supported modes: ");
- for (i=0,mask=1;i<8;i++,mask=mask << 1) {
- if (id->dma_1word & mask)
- printk("%d ",i);
- if (id->dma_1word & (mask << 8))
- printk("(active) ");
- }
- printk("\n");
- printk(KERN_INFO "ide-tape: Multi Word DMA supported modes: ");
- for (i=0,mask=1;i<8;i++,mask=mask << 1) {
- if (id->dma_mword & mask)
- printk("%d ",i);
- if (id->dma_mword & (mask << 8))
- printk("(active) ");
- }
- printk("\n");
- if (id->field_valid & 0x0002) {
- printk(KERN_INFO "ide-tape: Enhanced PIO Modes: %s\n",
- id->eide_pio_modes & 1 ? "Mode 3":"None");
- printk(KERN_INFO "ide-tape: Minimum Multi-word DMA cycle per word: ");
- if (id->eide_dma_min == 0)
- printk("Not supported\n");
- else
- printk("%d ns\n",id->eide_dma_min);
-
- printk(KERN_INFO "ide-tape: Manufacturer\'s Recommended Multi-word cycle: ");
- if (id->eide_dma_time == 0)
- printk("Not supported\n");
- else
- printk("%d ns\n",id->eide_dma_time);
-
- printk(KERN_INFO "ide-tape: Minimum PIO cycle without IORDY: ");
- if (id->eide_pio == 0)
- printk("Not supported\n");
- else
- printk("%d ns\n",id->eide_pio);
-
- printk(KERN_INFO "ide-tape: Minimum PIO cycle with IORDY: ");
- if (id->eide_pio_iordy == 0)
- printk("Not supported\n");
- else
- printk("%d ns\n",id->eide_pio_iordy);
-
- } else
- printk(KERN_INFO "ide-tape: According to the device, fields 64-70 are not valid.\n");
#endif /* IDETAPE_DEBUG_INFO */
/* Check that we can support this device */
- if (gcw.protocol !=2 )
- printk(KERN_ERR "ide-tape: Protocol is not ATAPI\n");
+ if (gcw.protocol != 2)
+ printk(KERN_ERR "ide-tape: Protocol (0x%02x) is not ATAPI\n",
+ gcw.protocol);
else if (gcw.device_type != 1)
- printk(KERN_ERR "ide-tape: Device type is not set to tape\n");
+ printk(KERN_ERR "ide-tape: Device type (0x%02x) is not set "
+ "to tape\n", gcw.device_type);
else if (!gcw.removable)
printk(KERN_ERR "ide-tape: The removable flag is not set\n");
else if (gcw.packet_size != 0) {
- printk(KERN_ERR "ide-tape: Packet size is not 12 bytes long\n");
- if (gcw.packet_size == 1)
- printk(KERN_ERR "ide-tape: Sorry, padding to 16 bytes is still not supported\n");
+ printk(KERN_ERR "ide-tape: Packet size (0x%02x) is not 12 "
+ "bytes long\n", gcw.packet_size);
} else
return 1;
return 0;
{
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t pc;
- idetape_mode_parameter_header_t *header;
idetape_capabilities_page_t *capabilities;
-
+
idetape_create_mode_sense_cmd(&pc, IDETAPE_CAPABILITIES_PAGE);
if (idetape_queue_pc_tail(drive, &pc)) {
printk(KERN_ERR "ide-tape: Can't get tape parameters - assuming some default values\n");
tape->capabilities.buffer_size = 6 * 52;
return;
}
- header = (idetape_mode_parameter_header_t *) pc.buffer;
- capabilities = (idetape_capabilities_page_t *) (pc.buffer + sizeof(idetape_mode_parameter_header_t) + header->bdl);
+ capabilities = (idetape_capabilities_page_t *)
+ (pc.buffer + 4 + pc.buffer[3]);
capabilities->max_speed = ntohs(capabilities->max_speed);
capabilities->ctl = ntohs(capabilities->ctl);
#if IDETAPE_DEBUG_INFO
printk(KERN_INFO "ide-tape: Dumping the results of the MODE SENSE packet command\n");
printk(KERN_INFO "ide-tape: Mode Parameter Header:\n");
- printk(KERN_INFO "ide-tape: Mode Data Length - %d\n",header->mode_data_length);
- printk(KERN_INFO "ide-tape: Medium Type - %d\n",header->medium_type);
- printk(KERN_INFO "ide-tape: Device Specific Parameter - %d\n",header->dsp);
- printk(KERN_INFO "ide-tape: Block Descriptor Length - %d\n",header->bdl);
-
+ printk(KERN_INFO "ide-tape: Mode Data Length - %d\n", pc.buffer[0]);
+ printk(KERN_INFO "ide-tape: Medium Type - %d\n", pc.buffer[1]);
+ printk(KERN_INFO "ide-tape: Device Specific Parameter - %d\n",
+ pc.buffer[2]);
+ printk(KERN_INFO "ide-tape: Block Descriptor Length - %d\n",
+ pc.buffer[3]);
+
printk(KERN_INFO "ide-tape: Capabilities and Mechanical Status Page:\n");
printk(KERN_INFO "ide-tape: Page code - %d\n",capabilities->page_code);
printk(KERN_INFO "ide-tape: Page length - %d\n",capabilities->page_length);
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t pc;
- idetape_mode_parameter_header_t *header;
idetape_parameter_block_descriptor_t *block_descrp;
-
+
idetape_create_mode_sense_cmd(&pc, IDETAPE_BLOCK_DESCRIPTOR);
if (idetape_queue_pc_tail(drive, &pc)) {
printk(KERN_ERR "ide-tape: Can't get block descriptor\n");
}
return;
}
- header = (idetape_mode_parameter_header_t *) pc.buffer;
- block_descrp = (idetape_parameter_block_descriptor_t *) (pc.buffer + sizeof(idetape_mode_parameter_header_t));
+ block_descrp = (idetape_parameter_block_descriptor_t *)(pc.buffer + 4);
tape->tape_block_size =( block_descrp->length[0]<<16) + (block_descrp->length[1]<<8) + block_descrp->length[2];
- tape->drv_write_prot = (header->dsp & 0x80) >> 7;
+ tape->drv_write_prot = (pc.buffer[2] & 0x80) >> 7;
#if IDETAPE_DEBUG_INFO
printk(KERN_INFO "ide-tape: Adjusted block size - %d\n", tape->tape_block_size);
spin_lock_init(&tape->spinlock);
drive->dsc_overlap = 1;
-#ifdef CONFIG_BLK_DEV_IDEPCI
- if (HWIF(drive)->pci_dev != NULL) {
- /*
- * These two ide-pci host adapters appear to need DSC overlap disabled.
- * This probably needs further analysis.
- */
- if ((HWIF(drive)->pci_dev->device == PCI_DEVICE_ID_ARTOP_ATP850UF) ||
- (HWIF(drive)->pci_dev->device == PCI_DEVICE_ID_TTI_HPT343)) {
- printk(KERN_INFO "ide-tape: %s: disabling DSC overlap\n", tape->name);
- drive->dsc_overlap = 0;
- }
+ if (drive->hwif->host_flags & IDE_HFLAG_NO_DSC) {
+ printk(KERN_INFO "ide-tape: %s: disabling DSC overlap\n",
+ tape->name);
+ drive->dsc_overlap = 0;
}
-#endif /* CONFIG_BLK_DEV_IDEPCI */
/* Seagate Travan drives do not support DSC overlap. */
if (strstr(drive->id->model, "Seagate STT3401"))
drive->dsc_overlap = 0;
drive->dsc_overlap = 0;
drive->driver_data = NULL;
- class_device_destroy(idetape_sysfs_class,
- MKDEV(IDETAPE_MAJOR, tape->minor));
- class_device_destroy(idetape_sysfs_class,
- MKDEV(IDETAPE_MAJOR, tape->minor + 128));
+ device_destroy(idetape_sysfs_class, MKDEV(IDETAPE_MAJOR, tape->minor));
+ device_destroy(idetape_sysfs_class, MKDEV(IDETAPE_MAJOR, tape->minor + 128));
idetape_devs[tape->minor] = NULL;
g->private_data = NULL;
put_disk(g);
idetape_setup(drive, tape, minor);
- class_device_create(idetape_sysfs_class, NULL,
- MKDEV(IDETAPE_MAJOR, minor), &drive->gendev, "%s", tape->name);
- class_device_create(idetape_sysfs_class, NULL,
- MKDEV(IDETAPE_MAJOR, minor + 128), &drive->gendev, "n%s", tape->name);
+ device_create(idetape_sysfs_class, &drive->gendev,
+ MKDEV(IDETAPE_MAJOR, minor), "%s", tape->name);
+ device_create(idetape_sysfs_class, &drive->gendev,
+ MKDEV(IDETAPE_MAJOR, minor + 128), "n%s", tape->name);
g->fops = &idetape_block_ops;
ide_register_region(g);