menuconfig NEW_LEDS
bool "LED Support"
- depends on HAS_IOMEM
help
Say Y to enable Linux LED support. This allows control of supported
LEDs from both userspace and optionally, by kernel events (triggers).
comment "LED drivers"
+config LEDS_ATMEL_PWM
+ tristate "LED Support using Atmel PWM outputs"
+ depends on LEDS_CLASS && ATMEL_PWM
+ help
+ This option enables support for LEDs driven using outputs
+ of the dedicated PWM controller found on newer Atmel SOCs.
+
config LEDS_CORGI
tristate "LED Support for the Sharp SL-C7x0 series"
depends on LEDS_CLASS && PXA_SHARP_C7xx
This option enables support for the LEDs on Sharp Zaurus
SL-Cxx00 series (C1000, C3000, C3100).
-config LEDS_IXP4XX
- tristate "LED Support for GPIO connected LEDs on IXP4XX processors"
- depends on LEDS_CLASS && ARCH_IXP4XX
- help
- This option enables support for the LEDs connected to GPIO
- outputs of the Intel IXP4XX processors. To be useful the
- particular board must have LEDs and they must be connected
- to the GPIO lines. If unsure, say Y.
-
-config LEDS_TOSA
- tristate "LED Support for the Sharp SL-6000 series"
- depends on LEDS_CLASS && PXA_SHARPSL
- help
- This option enables support for the LEDs on Sharp Zaurus
- SL-6000 series.
-
config LEDS_S3C24XX
tristate "LED Support for Samsung S3C24XX GPIO LEDs"
depends on LEDS_CLASS && ARCH_S3C2410
This option enables support for the Soekris net4801 and net4826 error
LED.
+config LEDS_FSG
+ tristate "LED Support for the Freecom FSG-3"
+ depends on LEDS_CLASS && MACH_FSG
+ help
+ This option enables support for the LEDs on the Freecom FSG-3.
+
config LEDS_WRAP
tristate "LED Support for the WRAP series LEDs"
depends on LEDS_CLASS && SCx200_GPIO
help
This option enables support for the Cobalt Raq series LEDs.
+config LEDS_HP6XX
+ tristate "LED Support for the HP Jornada 6xx"
+ depends on LEDS_CLASS && SH_HP6XX
+ help
+ This option enables led support for the handheld
+ HP Jornada 620/660/680/690.
+
+config LEDS_PCA9532
+ tristate "LED driver for PCA9532 dimmer"
+ depends on LEDS_CLASS && I2C && INPUT && EXPERIMENTAL
+ help
+ This option enables support for NXP pca9532
+ led controller. It is generally only usefull
+ as a platform driver
+
config LEDS_GPIO
tristate "LED Support for GPIO connected LEDs"
depends on LEDS_CLASS && GENERIC_GPIO
outputs. To be useful the particular board must have LEDs
and they must be connected to the GPIO lines.
+config LEDS_CM_X270
+ tristate "LED Support for the CM-X270 LEDs"
+ depends on LEDS_CLASS && MACH_ARMCORE
+ help
+ This option enables support for the CM-X270 LEDs.
+
+config LEDS_CLEVO_MAIL
+ tristate "Mail LED on Clevo notebook (EXPERIMENTAL)"
+ depends on LEDS_CLASS && X86 && SERIO_I8042 && DMI && EXPERIMENTAL
+ help
+ This driver makes the mail LED accessible from userspace
+ programs through the leds subsystem. This LED have three
+ known mode: off, blink at 0.5Hz and blink at 1Hz.
+
+ The driver supports two kinds of interface: using ledtrig-timer
+ or through /sys/class/leds/clevo::mail/brightness. As this LED
+ cannot change it's brightness it blinks instead. The brightness
+ value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
+ blink at 1Hz.
+
+ This module can drive the mail LED for the following notebooks:
+
+ Clevo D400P
+ Clevo D410J
+ Clevo D410V
+ Clevo D400V/D470V (not tested, but might work)
+ Clevo M540N
+ Clevo M5x0N (not tested, but might work)
+ Positivo Mobile (Clevo M5x0V)
+
+ If your model is not listed here you can try the "nodetect"
+ module paramter.
+
+ To compile this driver as a module, choose M here: the
+ module will be called leds-clevo-mail.
+
+config LEDS_PCA955X
+ tristate "LED Support for PCA955x I2C chips"
+ depends on LEDS_CLASS && I2C
+ help
+ This option enables support for LEDs connected to PCA955x
+ LED driver chips accessed via the I2C bus. Supported
+ devices include PCA9550, PCA9551, PCA9552, and PCA9553.
+
comment "LED Triggers"
config LEDS_TRIGGERS
depends on LEDS_TRIGGERS
help
This allows LEDs to be controlled by a programmable timer
- via sysfs. If unsure, say Y.
+ via sysfs. Some LED hardware can be programmed to start
+ blinking the LED without any further software interaction.
+ For more details read Documentation/leds-class.txt.
+
+ If unsure, say Y.
config LEDS_TRIGGER_IDE_DISK
bool "LED IDE Disk Trigger"
load average.
If unsure, say Y.
+config LEDS_TRIGGER_DEFAULT_ON
+ tristate "LED Default ON Trigger"
+ depends on LEDS_TRIGGERS
+ help
+ This allows LEDs to be initialised in the ON state.
+ If unsure, say Y.
+
endif # NEW_LEDS