Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6

[mv-sheeva.git] / drivers / net / bfin_mac.c

diff --git a/drivers/net/bfin_mac.c b/drivers/net/bfin_mac.c
index 78e31aa861e020e461336e2323cea4647d7cb9c8..9f971ed6b58d3193968ca14d3971b394182ce89e 100644 (file)
--- a/drivers/net/bfin_mac.c
+++ b/drivers/net/bfin_mac.c
@@ -415,11 +415,11 @@ static int mii_probe(struct net_device *dev)
        }
 
 #if defined(CONFIG_BFIN_MAC_RMII)
-       phydev = phy_connect(dev, phydev->dev.bus_id, &bfin_mac_adjust_link, 0,
-                       PHY_INTERFACE_MODE_RMII);
+       phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link,
+                       0, PHY_INTERFACE_MODE_RMII);
 #else
-       phydev = phy_connect(dev, phydev->dev.bus_id, &bfin_mac_adjust_link, 0,
-                       PHY_INTERFACE_MODE_MII);
+       phydev = phy_connect(dev, dev_name(&phydev->dev), &bfin_mac_adjust_link,
+                       0, PHY_INTERFACE_MODE_MII);
 #endif
 
        if (IS_ERR(phydev)) {
@@ -447,7 +447,7 @@ static int mii_probe(struct net_device *dev)
        printk(KERN_INFO "%s: attached PHY driver [%s] "
               "(mii_bus:phy_addr=%s, irq=%d, mdc_clk=%dHz(mdc_div=%d)"
               "@sclk=%dMHz)\n",
-              DRV_NAME, phydev->drv->name, phydev->dev.bus_id, phydev->irq,
+              DRV_NAME, phydev->drv->name, dev_name(&phydev->dev), phydev->irq,
               MDC_CLK, mdc_div, sclk/1000000);
 
        return 0;
@@ -488,7 +488,7 @@ static void bfin_mac_ethtool_getdrvinfo(struct net_device *dev,
        strcpy(info->driver, DRV_NAME);
        strcpy(info->version, DRV_VERSION);
        strcpy(info->fw_version, "N/A");
-       strcpy(info->bus_info, dev->dev.bus_id);
+       strcpy(info->bus_info, dev_name(&dev->dev));
 }
 
 static struct ethtool_ops bfin_mac_ethtool_ops = {
@@ -979,6 +979,20 @@ static int bfin_mac_open(struct net_device *dev)
        return 0;
 }
 
+static const struct net_device_ops bfin_mac_netdev_ops = {
+       .ndo_open               = bfin_mac_open,
+       .ndo_stop               = bfin_mac_close,
+       .ndo_start_xmit         = bfin_mac_hard_start_xmit,
+       .ndo_set_mac_address    = bfin_mac_set_mac_address,
+       .ndo_tx_timeout         = bfin_mac_timeout,
+       .ndo_set_multicast_list = bfin_mac_set_multicast_list,
+       .ndo_validate_addr      = eth_validate_addr,
+       .ndo_change_mtu         = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = bfin_mac_poll,
+#endif
+};
+
 /*
  *
  * this makes the board clean up everything that it can
@@ -1086,15 +1100,7 @@ static int __devinit bfin_mac_probe(struct platform_device *pdev)
        /* Fill in the fields of the device structure with ethernet values. */
        ether_setup(ndev);
 
-       ndev->open = bfin_mac_open;
-       ndev->stop = bfin_mac_close;
-       ndev->hard_start_xmit = bfin_mac_hard_start_xmit;
-       ndev->set_mac_address = bfin_mac_set_mac_address;
-       ndev->tx_timeout = bfin_mac_timeout;
-       ndev->set_multicast_list = bfin_mac_set_multicast_list;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       ndev->poll_controller = bfin_mac_poll;
-#endif
+       ndev->netdev_ops = &bfin_mac_netdev_ops;
        ndev->ethtool_ops = &bfin_mac_ethtool_ops;
 
        spin_lock_init(&lp->lock);