ath9k: Add debug counters for TX

[mv-sheeva.git] / drivers / net / bnx2x_hsi.h

diff --git a/drivers/net/bnx2x_hsi.h b/drivers/net/bnx2x_hsi.h
index 03c62421d999ddb0e6687f7dde070b9fbd86f216..7de83c4a557a86d198378845652563441bb89b93 100644 (file)
--- a/drivers/net/bnx2x_hsi.h
+++ b/drivers/net/bnx2x_hsi.h
@@ -91,6 +91,21 @@ struct shared_hw_cfg {                                        /* NVRAM Offset */
 
 #define SHARED_HW_CFG_HIDE_PORT1                   0x00002000
 
+       /*  The fan failure mechanism is usually related to the PHY type
+         since the power consumption of the board is determined by the PHY.
+         Currently, fan is required for most designs with SFX7101, BCM8727
+         and BCM8481. If a fan is not required for a board which uses one
+         of those PHYs, this field should be set to "Disabled". If a fan is
+         required for a different PHY type, this option should be set to
+         "Enabled".
+         The fan failure indication is expected on
+         SPIO5 */
+#define SHARED_HW_CFG_FAN_FAILURE_MASK                       0x00180000
+#define SHARED_HW_CFG_FAN_FAILURE_SHIFT                      19
+#define SHARED_HW_CFG_FAN_FAILURE_PHY_TYPE                   0x00000000
+#define SHARED_HW_CFG_FAN_FAILURE_DISABLED                   0x00080000
+#define SHARED_HW_CFG_FAN_FAILURE_ENABLED                    0x00100000
+
        u32 power_dissipated;                                   /* 0x11c */
 #define SHARED_HW_CFG_POWER_DIS_CMN_MASK           0xff000000
 #define SHARED_HW_CFG_POWER_DIS_CMN_SHIFT          24
@@ -233,6 +248,8 @@ struct port_hw_cfg {                            /* port 0: 0x12c  port 1: 0x2bc */
 #define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726      0x00000600
 #define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481      0x00000700
 #define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101      0x00000800
+#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727      0x00000900
+#define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC   0x00000a00
 #define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE      0x0000fd00
 #define PORT_HW_CFG_XGXS_EXT_PHY_TYPE_NOT_CONN     0x0000ff00
 
@@ -343,10 +360,16 @@ struct port_feat_cfg {                        /* port 0: 0x454  port 1: 0x4c8 */
 #define PORT_FEATURE_MBA_ENABLED                   0x02000000
 #define PORT_FEATURE_MFW_ENABLED                   0x04000000
 
-       /*  Check the optic vendor via i2c before allowing it to be used by
-         SW */
-#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLED              0x00000000
-#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_ENABLED               0x08000000
+       /* Reserved bits: 28-29 */
+       /*  Check the optic vendor via i2c against a list of approved modules
+         in a separate nvram image */
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_MASK                  0xE0000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_SHIFT                 29
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_NO_ENFORCEMENT        0x00000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_DISABLE_TX_LASER       0x20000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_WARNING_MSG           0x40000000
+#define PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_POWER_DOWN            0x60000000
+
 
        u32 wol_config;
        /* Default is used when driver sets to "auto" mode */
@@ -642,6 +665,12 @@ struct drv_func_mb {
 #define DRV_MSG_CODE_GET_UPGRADE_KEY                   0x81000000
 #define DRV_MSG_CODE_GET_MANUF_KEY                     0x82000000
 #define DRV_MSG_CODE_LOAD_L2B_PRAM                     0x90000000
+       /*
+        * The optic module verification commands requris bootcode
+        * v5.0.6 or later
+        */
+#define DRV_MSG_CODE_VRFY_OPT_MDL                      0xa0000000
+#define REQ_BC_VER_4_VRFY_OPT_MDL                      0x00050006
 
 #define BIOS_MSG_CODE_LIC_CHALLENGE                    0xff010000
 #define BIOS_MSG_CODE_LIC_RESPONSE                     0xff020000
@@ -676,6 +705,9 @@ struct drv_func_mb {
 #define FW_MSG_CODE_L2B_PRAM_C_LOAD_FAILURE            0x90220000
 #define FW_MSG_CODE_L2B_PRAM_X_LOAD_FAILURE            0x90230000
 #define FW_MSG_CODE_L2B_PRAM_U_LOAD_FAILURE            0x90240000
+#define FW_MSG_CODE_VRFY_OPT_MDL_SUCCESS               0xa0100000
+#define FW_MSG_CODE_VRFY_OPT_MDL_INVLD_IMG             0xa0200000
+#define FW_MSG_CODE_VRFY_OPT_MDL_UNAPPROVED            0xa0300000
 
 #define FW_MSG_CODE_LIC_CHALLENGE                      0xff010000
 #define FW_MSG_CODE_LIC_RESPONSE                       0xff020000