#include <linux/ethtool.h>
#include <linux/mutex.h>
-#include "bnx2x_reg.h"
-#include "bnx2x_fw_defs.h"
-#include "bnx2x_hsi.h"
-#include "bnx2x_link.h"
#include "bnx2x.h"
/********************************************************/
-#define SUPPORT_CL73 0 /* Currently no */
#define ETH_HLEN 14
#define ETH_OVREHEAD (ETH_HLEN + 8)/* 8 for CRC + VLAN*/
#define ETH_MIN_PACKET_SIZE 60
(_bank + (_addr & 0xf)), \
_val)
-static void bnx2x_set_phy_mdio(struct link_params *params)
+static void bnx2x_set_serdes_access(struct link_params *params)
{
struct bnx2x *bp = params->bp;
- REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST +
- params->port*0x18, 0);
- REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + params->port*0x18,
- DEFAULT_PHY_DEV_ADDR);
+ u32 emac_base = (params->port) ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
+ /* Set Clause 22 */
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 1);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245f8000);
+ udelay(500);
+ REG_WR(bp, emac_base + EMAC_REG_EMAC_MDIO_COMM, 0x245d000f);
+ udelay(500);
+ /* Set Clause 45 */
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_ST + params->port*0x10, 0);
+}
+static void bnx2x_set_phy_mdio(struct link_params *params, u8 phy_flags)
+{
+ struct bnx2x *bp = params->bp;
+ if (phy_flags & PHY_XGXS_FLAG) {
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_ST +
+ params->port*0x18, 0);
+ REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + params->port*0x18,
+ DEFAULT_PHY_DEV_ADDR);
+ } else {
+ bnx2x_set_serdes_access(params);
+
+ REG_WR(bp, NIG_REG_SERDES0_CTRL_MD_DEVAD +
+ params->port*0x10,
+ DEFAULT_PHY_DEV_ADDR);
+ }
}
static u32 bnx2x_bits_en(struct bnx2x *bp, u32 reg, u32 bits)
port*4, 0);
}
- /* enable emac */
- REG_WR(bp, NIG_REG_NIG_EMAC0_EN + port*4, 1);
+ bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_RX_MODE,
+ EMAC_RX_MODE_RESET);
+ bnx2x_bits_en(bp, emac_base + EMAC_REG_EMAC_TX_MODE,
+ EMAC_TX_MODE_RESET);
if (CHIP_REV_IS_SLOW(bp)) {
/* config GMII mode */
udelay(500);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_3_SET,
val);
- bnx2x_set_phy_mdio(params);
+ bnx2x_set_phy_mdio(params, phy_flags);
}
void bnx2x_link_status_update(struct link_params *params,
(mii_control |
MDIO_COMBO_IEEO_MII_CONTROL_RESET));
+ bnx2x_set_serdes_access(params);
+
/* wait for the reset to self clear */
for (i = 0; i < MDIO_ACCESS_TIMEOUT; i++) {
udelay(5);
MDIO_BAM_NEXT_PAGE_MP5_NEXT_PAGE_CTRL,
reg_val);
- /* Enable Clause 73 Aneg */
- if ((vars->line_speed == SPEED_AUTO_NEG) &&
- (SUPPORT_CL73)) {
- /* Enable BAM Station Manager */
-
- CL45_WR_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_USERB0,
- MDIO_CL73_USERB0_CL73_BAM_CTRL1,
- (MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_EN |
- MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_STATION_MNGR_EN |
- MDIO_CL73_USERB0_CL73_BAM_CTRL1_BAM_NP_AFTER_BP_EN));
-
- /* Merge CL73 and CL37 aneg resolution */
- CL45_RD_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_USERB0,
- MDIO_CL73_USERB0_CL73_BAM_CTRL3,
- ®_val);
+ /* CL73 Autoneg Disabled */
+ reg_val = 0;
- CL45_WR_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_USERB0,
- MDIO_CL73_USERB0_CL73_BAM_CTRL3,
- (reg_val |
- MDIO_CL73_USERB0_CL73_BAM_CTRL3_USE_CL73_HCD_MR));
-
- /* Set the CL73 AN speed */
-
- CL45_RD_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV2, ®_val);
- /* In the SerDes we support only the 1G.
- In the XGXS we support the 10G KX4
- but we currently do not support the KR */
- if (vars->phy_flags & PHY_XGXS_FLAG) {
- DP(NETIF_MSG_LINK, "XGXS\n");
- /* 10G KX4 */
- reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_10G_KX4;
- } else {
- DP(NETIF_MSG_LINK, "SerDes\n");
- /* 1000M KX */
- reg_val |= MDIO_CL73_IEEEB1_AN_ADV2_ADVR_1000M_KX;
- }
- CL45_WR_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_IEEEB1,
- MDIO_CL73_IEEEB1_AN_ADV2, reg_val);
-
- /* CL73 Autoneg Enabled */
- reg_val = MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN;
- } else {
- /* CL73 Autoneg Disabled */
- reg_val = 0;
- }
CL45_WR_OVER_CL22(bp, params->port,
params->phy_addr,
MDIO_REG_BANK_CL73_IEEEB0,
static void bnx2x_restart_autoneg(struct link_params *params)
{
struct bnx2x *bp = params->bp;
+ u16 mii_control;
DP(NETIF_MSG_LINK, "bnx2x_restart_autoneg\n");
- if (SUPPORT_CL73) {
- /* enable and restart clause 73 aneg */
- u16 an_ctrl;
-
- CL45_RD_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- &an_ctrl);
- CL45_WR_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_CL73_IEEEB0,
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL,
- (an_ctrl |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_AN_EN |
- MDIO_CL73_IEEEB0_CL73_AN_CONTROL_RESTART_AN));
-
- } else {
- /* Enable and restart BAM/CL37 aneg */
- u16 mii_control;
+ /* Enable and restart BAM/CL37 aneg */
- CL45_RD_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- &mii_control);
- DP(NETIF_MSG_LINK,
- "bnx2x_restart_autoneg mii_control before = 0x%x\n",
- mii_control);
- CL45_WR_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_COMBO_IEEE0,
- MDIO_COMBO_IEEE0_MII_CONTROL,
- (mii_control |
- MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
- MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
- }
+ CL45_RD_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ &mii_control);
+ DP(NETIF_MSG_LINK,
+ "bnx2x_restart_autoneg mii_control before = 0x%x\n",
+ mii_control);
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ MDIO_REG_BANK_COMBO_IEEE0,
+ MDIO_COMBO_IEEE0_MII_CONTROL,
+ (mii_control |
+ MDIO_COMBO_IEEO_MII_CONTROL_AN_EN |
+ MDIO_COMBO_IEEO_MII_CONTROL_RESTART_AN));
}
static void bnx2x_initialize_sgmii_process(struct link_params *params,
return rc;
}
-static void bnx2x_set_sgmii_tx_driver(struct link_params *params)
+static void bnx2x_set_gmii_tx_driver(struct link_params *params)
{
struct bnx2x *bp = params->bp;
u16 lp_up2;
u16 tx_driver;
+ u16 bank;
/* read precomp */
-
CL45_RD_OVER_CL22(bp, params->port,
params->phy_addr,
MDIO_REG_BANK_OVER_1G,
MDIO_OVER_1G_LP_UP2, &lp_up2);
- CL45_RD_OVER_CL22(bp, params->port,
- params->phy_addr,
- MDIO_REG_BANK_TX0,
- MDIO_TX0_TX_DRIVER, &tx_driver);
-
/* bits [10:7] at lp_up2, positioned at [15:12] */
lp_up2 = (((lp_up2 & MDIO_OVER_1G_LP_UP2_PREEMPHASIS_MASK) >>
MDIO_OVER_1G_LP_UP2_PREEMPHASIS_SHIFT) <<
MDIO_TX0_TX_DRIVER_PREEMPHASIS_SHIFT);
- if ((lp_up2 != 0) &&
- (lp_up2 != (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK))) {
- /* replace tx_driver bits [15:12] */
- tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
- tx_driver |= lp_up2;
- CL45_WR_OVER_CL22(bp, params->port,
+ if (lp_up2 == 0)
+ return;
+
+ for (bank = MDIO_REG_BANK_TX0; bank <= MDIO_REG_BANK_TX3;
+ bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0)) {
+ CL45_RD_OVER_CL22(bp, params->port,
params->phy_addr,
- MDIO_REG_BANK_TX0,
- MDIO_TX0_TX_DRIVER, tx_driver);
+ bank,
+ MDIO_TX0_TX_DRIVER, &tx_driver);
+
+ /* replace tx_driver bits [15:12] */
+ if (lp_up2 !=
+ (tx_driver & MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK)) {
+ tx_driver &= ~MDIO_TX0_TX_DRIVER_PREEMPHASIS_MASK;
+ tx_driver |= lp_up2;
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_TX0_TX_DRIVER, tx_driver);
+ }
}
}
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
{
- u16 emac_base;
- emac_base = (params->port) ? GRCBASE_EMAC0 :
- GRCBASE_EMAC1;
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc801, &val);
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
if (val != 1) {
/* No need to workaround in 8073 A1 */
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc801, &val);
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
if (val > 0) {
/* No need to workaround in 8073 A1 */
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc820, &val);
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &val);
/* If bit [14] = 0 or bit [13] = 0, continue on with
system initialization (XAUI work-around not required,
as these bits indicate 2.5G or 1G link up). */
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc841, &val);
+ MDIO_PMA_REG_8073_XAUI_WA, &val);
if (val & (1<<15)) {
DP(NETIF_MSG_LINK,
"XAUI workaround has completed\n");
MDIO_PMA_REG_GEN_CTRL,
MDIO_PMA_REG_GEN_CTRL_ROM_MICRO_RESET);
+ bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_GEN_CTRL2,
+ 0x73A0);
+
/* Clear soft reset.
Will automatically reset micro-controller re-boot */
bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
MDIO_PMA_REG_GEN_CTRL,
MDIO_PMA_REG_GEN_CTRL_ROM_RESET_INTERNAL_MP);
- /* wait for 100ms for microcode load */
- msleep(100);
+ /* wait for 150ms for microcode load */
+ msleep(150);
/* Disable serial boot control, tristates pins SS_N, SCK, MOSI, MISO */
bnx2x_cl45_write(bp, port, ext_phy_type, ext_phy_addr,
u8 ext_phy_addr = ((params->ext_phy_config &
PORT_HW_CFG_XGXS_EXT_PHY_ADDR_MASK) >>
PORT_HW_CFG_XGXS_EXT_PHY_ADDR_SHIFT);
-
+ u16 cur_limiting_mode;
if (bnx2x_read_sfp_module_eeprom(params,
SFP_EEPROM_OPTIONS_ADDR,
SFP_EEPROM_OPTIONS_SIZE,
}
limiting_mode = !(options[0] &
SFP_EEPROM_OPTIONS_LINEAR_RX_OUT_MASK);
+
+ bnx2x_cl45_read(bp, port,
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_ROM_VER2,
+ &cur_limiting_mode);
+ DP(NETIF_MSG_LINK, "Current Limiting mode is 0x%x\n",
+ cur_limiting_mode);
+
if (limiting_mode &&
(module_type != SFP_MODULE_TYPE_PASSIVE_COPPER_CABLE)) {
DP(NETIF_MSG_LINK,
MDIO_PMA_REG_ROM_VER2,
SFP_LIMITING_MODE_VALUE);
} else { /* LRM mode ( default )*/
- u16 cur_limiting_mode;
+
DP(NETIF_MSG_LINK, "Module options = 0x%x.Setting LRM MODE\n",
options[0]);
- bnx2x_cl45_read(bp, port,
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726,
- ext_phy_addr,
- MDIO_PMA_DEVAD,
- MDIO_PMA_REG_ROM_VER2,
- &cur_limiting_mode);
-
/* Changing to LRM mode takes quite few seconds.
So do it only if current mode is limiting
( default is LRM )*/
params->port);
/* Check and set limiting mode / LRM mode */
- if (bnx2x_bcm8726_set_limiting_mode(params, module_type)
- != 0) {
- DP(NETIF_MSG_LINK, "Setting limiting mode failed!!\n");
- return -EINVAL;
- }
+ bnx2x_bcm8726_set_limiting_mode(params, module_type);
/* Enable transmit for this module */
bnx2x_bcm8726_set_transmitter(bp, params->port,
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc801, &val);
+ MDIO_PMA_REG_8073_CHIP_REV, &val);
if (val == 0) {
/* Mustn't set low power mode in 8073 A0 */
MDIO_AN_DEVAD,
MDIO_AN_REG_ADV_PAUSE, val);
}
+static void bnx2x_set_preemphasis(struct link_params *params)
+{
+ u16 bank, i = 0;
+ struct bnx2x *bp = params->bp;
+
+ for (bank = MDIO_REG_BANK_RX0, i = 0; bank <= MDIO_REG_BANK_RX3;
+ bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0), i++) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_RX0_RX_EQ_BOOST,
+ params->xgxs_config_rx[i]);
+ }
+ for (bank = MDIO_REG_BANK_TX0, i = 0; bank <= MDIO_REG_BANK_TX3;
+ bank += (MDIO_REG_BANK_TX1 - MDIO_REG_BANK_TX0), i++) {
+ CL45_WR_OVER_CL22(bp, params->port,
+ params->phy_addr,
+ bank,
+ MDIO_TX0_TX_DRIVER,
+ params->xgxs_config_tx[i]);
+ }
+}
static void bnx2x_init_internal_phy(struct link_params *params,
struct link_vars *vars)
{
struct bnx2x *bp = params->bp;
- u8 port = params->port;
if (!(vars->phy_flags & PHY_SGMII_FLAG)) {
- u16 bank, rx_eq;
-
- rx_eq = ((params->serdes_config &
- PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_MASK) >>
- PORT_HW_CFG_SERDES_RX_DRV_EQUALIZER_SHIFT);
-
- DP(NETIF_MSG_LINK, "setting rx eq to 0x%x\n", rx_eq);
- for (bank = MDIO_REG_BANK_RX0; bank <= MDIO_REG_BANK_RX_ALL;
- bank += (MDIO_REG_BANK_RX1-MDIO_REG_BANK_RX0)) {
- CL45_WR_OVER_CL22(bp, port,
- params->phy_addr,
- bank ,
- MDIO_RX0_RX_EQ_BOOST,
- ((rx_eq &
- MDIO_RX0_RX_EQ_BOOST_EQUALIZER_CTRL_MASK) |
- MDIO_RX0_RX_EQ_BOOST_OFFSET_CTRL));
- }
+ if ((XGXS_EXT_PHY_TYPE(params->ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) &&
+ (params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED))
+ bnx2x_set_preemphasis(params);
/* forced speed requested? */
if (vars->line_speed != SPEED_AUTO_NEG) {
MDIO_WIS_DEVAD,
MDIO_WIS_REG_LASI_CNTL, 0x1);
- bnx2x_save_bcm_spirom_ver(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- params->shmem_base);
+ /* BCM8705 doesn't have microcode, hence the 0 */
+ bnx2x_save_spirom_version(bp, params->port,
+ params->shmem_base, 0);
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
}
DP(NETIF_MSG_LINK, "XGXS 8706 is initialized "
"after %d ms\n", cnt);
+ if ((params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
+ u8 i;
+ u16 reg;
+ for (i = 0; i < 4; i++) {
+ reg = MDIO_XS_8706_REG_BANK_RX0 +
+ i*(MDIO_XS_8706_REG_BANK_RX1 -
+ MDIO_XS_8706_REG_BANK_RX0);
+ bnx2x_cl45_read(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_XS_DEVAD,
+ reg, &val);
+ /* Clear first 3 bits of the control */
+ val &= ~0x7;
+ /* Set control bits according to
+ configuation */
+ val |= (params->xgxs_config_rx[i] &
+ 0x7);
+ DP(NETIF_MSG_LINK, "Setting RX"
+ "Equalizer to BCM8706 reg 0x%x"
+ " <-- val 0x%x\n", reg, val);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_XS_DEVAD,
+ reg, val);
+ }
+ }
/* Force speed */
/* First enable LASI */
bnx2x_cl45_write(bp, params->port,
ext_phy_addr, MDIO_PMA_DEVAD,
MDIO_PMA_REG_LASI_CTRL, 1);
}
+
+ /* Set TX PreEmphasis if needed */
+ if ((params->feature_config_flags &
+ FEATURE_CONFIG_OVERRIDE_PREEMPHASIS_ENABLED)) {
+ DP(NETIF_MSG_LINK, "Setting TX_CTRL1 0x%x,"
+ "TX_CTRL2 0x%x\n",
+ params->xgxs_config_tx[0],
+ params->xgxs_config_tx[1]);
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TX_CTRL1,
+ params->xgxs_config_tx[0]);
+
+ bnx2x_cl45_write(bp, params->port,
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8726_TX_CTRL2,
+ params->xgxs_config_tx[1]);
+ }
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
ext_phy_type,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xca13,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
&tmp1);
bnx2x_cl45_read(bp, params->port,
ext_phy_type,
ext_phy_addr,
MDIO_AN_DEVAD,
- 0x8329, &tmp1);
+ MDIO_AN_REG_8073_2_5G, &tmp1);
if (((params->speed_cap_mask &
PORT_HW_CFG_SPEED_CAPABILITY_D0_2_5G) &&
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xc801, &phy_ver);
+ MDIO_PMA_REG_8073_CHIP_REV, &phy_ver);
DP(NETIF_MSG_LINK, "Add 2.5G\n");
if (phy_ver > 0)
tmp1 |= 1;
ext_phy_type,
ext_phy_addr,
MDIO_AN_DEVAD,
- 0x8329, tmp1);
+ MDIO_AN_REG_8073_2_5G, tmp1);
}
/* Add support for CL37 (passive mode) II */
ext_phy_type,
ext_phy_addr,
MDIO_PMA_DEVAD,
- 0xca13,
+ MDIO_PMA_REG_M8051_MSGOUT_REG,
&val1);
/* Check the LASI */
}
}
bnx2x_cl45_read(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- MDIO_AN_DEVAD,
- 0x8304,
- &an1000_status);
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
bnx2x_cl45_read(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- MDIO_AN_DEVAD,
- 0x8304,
- &an1000_status);
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
/* Check the link status on 1.1.2 */
bnx2x_cl45_read(bp, params->port,
"an_link_status=0x%x\n",
val2, val1, an1000_status);
- ext_phy_link_up = (((val1 & 4) == 4) ||
+ ext_phy_link_up = (((val1 & 4) == 4) ||
(an1000_status & (1<<1)));
if (ext_phy_link_up &&
bnx2x_8073_is_snr_needed(params)) {
}
bnx2x_cl45_read(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- MDIO_PMA_DEVAD,
- 0xc820,
- &link_status);
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_PMA_DEVAD,
+ MDIO_PMA_REG_8073_SPEED_LINK_STATUS,
+ &link_status);
/* Bits 0..2 --> speed detected,
bits 13..15--> link is down */
} else {
/* See if 1G link is up for the 8072 */
bnx2x_cl45_read(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- MDIO_AN_DEVAD,
- 0x8304,
- &an1000_status);
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
bnx2x_cl45_read(bp, params->port,
- ext_phy_type,
- ext_phy_addr,
- MDIO_AN_DEVAD,
- 0x8304,
- &an1000_status);
+ ext_phy_type,
+ ext_phy_addr,
+ MDIO_AN_DEVAD,
+ MDIO_AN_REG_LINK_STATUS,
+ &an1000_status);
if (an1000_status & (1<<1)) {
ext_phy_link_up = 1;
vars->line_speed = SPEED_1000;
ext_phy_addr,
MDIO_PMA_DEVAD,
MDIO_PMA_REG_CTRL,
- &ctrl);
+ &ctrl);
if (!(ctrl & (1<<15))) {
DP(NETIF_MSG_LINK, "Reset completed\n\n");
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481:
status = bnx2x_format_ver(spirom_ver, version, len);
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT:
/* init ext phy and enable link state int */
non_ext_phy = ((ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ||
- (params->loopback_mode == LOOPBACK_XGXS_10) ||
- (params->loopback_mode == LOOPBACK_EXT_PHY));
+ (params->loopback_mode == LOOPBACK_XGXS_10));
if (non_ext_phy ||
(ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705) ||
(ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726) ||
- (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481)) {
+ (ext_phy_type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481) ||
+ (params->loopback_mode == LOOPBACK_EXT_PHY)) {
if (params->req_line_speed == SPEED_AUTO_NEG)
bnx2x_set_parallel_detection(params, vars->phy_flags);
bnx2x_init_internal_phy(params, vars);
return -EINVAL;
break;
}
+ DP(NETIF_MSG_LINK, "Phy address = 0x%x\n", params->phy_addr);
bnx2x_link_initialize(params, vars);
msleep(30);
if (gp_status & MDIO_AN_CL73_OR_37_COMPLETE) {
if (!(vars->phy_flags &
PHY_SGMII_FLAG))
- bnx2x_set_sgmii_tx_driver(params);
+ bnx2x_set_gmii_tx_driver(params);
}
}
/* PART3 - complete TX_POWER_DOWN process, and set GPIO2 back to low */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
- /* Phase2 of POWER_DOWN_RESET*/
+ /* Phase2 of POWER_DOWN_RESET */
/* Release bit 10 (Release Tx power down) */
bnx2x_cl45_read(bp, port,
PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073,
u8 rc = 0;
u32 ext_phy_type;
- DP(NETIF_MSG_LINK, "bnx2x_common_init_phy\n");
+ DP(NETIF_MSG_LINK, "Begin common phy init\n");
/* Read the ext_phy_type for arbitrary port(0) */
ext_phy_type = XGXS_EXT_PHY_TYPE(