]> git.karo-electronics.de Git - karo-tx-linux.git/blobdiff - drivers/net/cs89x0.c
ath9k: Update copyright in all the files
[karo-tx-linux.git] / drivers / net / cs89x0.c
index 0b729f7d91fcb37862c64e5e0ee94b3067c2a81e..7433b88eed7e958f0666d02bafac62657add0bc0 100644 (file)
@@ -501,6 +501,21 @@ static void net_poll_controller(struct net_device *dev)
 }
 #endif
 
+static const struct net_device_ops net_ops = {
+       .ndo_open               = net_open,
+       .ndo_stop               = net_close,
+       .ndo_tx_timeout         = net_timeout,
+       .ndo_start_xmit         = net_send_packet,
+       .ndo_get_stats          = net_get_stats,
+       .ndo_set_multicast_list = set_multicast_list,
+       .ndo_set_mac_address    = set_mac_address,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+       .ndo_poll_controller    = net_poll_controller,
+#endif
+       .ndo_change_mtu         = eth_change_mtu,
+       .ndo_validate_addr      = eth_validate_addr,
+};
+
 /* This is the real probe routine.  Linux has a history of friendly device
    probes on the ISA bus.  A good device probes avoids doing writes, and
    verifies that the correct device exists and functions.
@@ -517,7 +532,6 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
        unsigned rev_type = 0;
        int eeprom_buff[CHKSUM_LEN];
        int retval;
-       DECLARE_MAC_BUF(mac);
 
        /* Initialize the device structure. */
        if (!modular) {
@@ -842,19 +856,10 @@ cs89x0_probe1(struct net_device *dev, int ioaddr, int modular)
        }
 
        /* print the ethernet address. */
-       printk(", MAC %s", print_mac(mac, dev->dev_addr));
-
-       dev->open               = net_open;
-       dev->stop               = net_close;
-       dev->tx_timeout         = net_timeout;
-       dev->watchdog_timeo     = HZ;
-       dev->hard_start_xmit    = net_send_packet;
-       dev->get_stats          = net_get_stats;
-       dev->set_multicast_list = set_multicast_list;
-       dev->set_mac_address    = set_mac_address;
-#ifdef CONFIG_NET_POLL_CONTROLLER
-       dev->poll_controller    = net_poll_controller;
-#endif
+       printk(", MAC %pM", dev->dev_addr);
+
+       dev->netdev_ops = &net_ops;
+       dev->watchdog_timeo = HZ;
 
        printk("\n");
        if (net_debug)
@@ -1021,14 +1026,13 @@ skip_this_frame:
        }
         skb->protocol=eth_type_trans(skb,dev);
        netif_rx(skb);
-       dev->last_rx = jiffies;
        lp->stats.rx_packets++;
        lp->stats.rx_bytes += length;
 }
 
 #endif /* ALLOW_DMA */
 
-void  __init reset_chip(struct net_device *dev)
+static void __init reset_chip(struct net_device *dev)
 {
 #if !defined(CONFIG_MACH_MX31ADS)
 #if !defined(CONFIG_MACH_IXDP2351) && !defined(CONFIG_ARCH_IXDP2X01)
@@ -1715,7 +1719,6 @@ net_rx(struct net_device *dev)
 
         skb->protocol=eth_type_trans(skb,dev);
        netif_rx(skb);
-       dev->last_rx = jiffies;
        lp->stats.rx_packets++;
        lp->stats.rx_bytes += length;
 }
@@ -1813,11 +1816,10 @@ static int set_mac_address(struct net_device *dev, void *p)
 
        memcpy(dev->dev_addr, addr->sa_data, dev->addr_len);
 
-       if (net_debug) {
-               DECLARE_MAC_BUF(mac);
-               printk("%s: Setting MAC address to %s.\n",
-                      dev->name, print_mac(mac, dev->dev_addr));
-       }
+       if (net_debug)
+               printk("%s: Setting MAC address to %pM.\n",
+                      dev->name, dev->dev_addr);
+
        /* set the Ethernet address */
        for (i=0; i < ETH_ALEN/2; i++)
                writereg(dev, PP_IA+i*2, dev->dev_addr[i*2] | (dev->dev_addr[i*2+1] << 8));