#define DRV_NAME "e100"
#define DRV_EXT "-NAPI"
-#define DRV_VERSION "3.4.14-k2"DRV_EXT
+#define DRV_VERSION "3.4.14-k4"DRV_EXT
#define DRV_DESCRIPTION "Intel(R) PRO/100 Network Driver"
#define DRV_COPYRIGHT "Copyright(c) 1999-2005 Intel Corporation"
#define PFX DRV_NAME ": "
}, *opts;
/* *INDENT-ON* */
+/*************************************************************************
+* CPUSaver parameters
+*
+* All CPUSaver parameters are 16-bit literals that are part of a
+* "move immediate value" instruction. By changing the value of
+* the literal in the instruction before the code is loaded, the
+* driver can change the algorithm.
+*
+* INTDELAY - This loads the dead-man timer with its inital value.
+* When this timer expires the interrupt is asserted, and the
+* timer is reset each time a new packet is received. (see
+* BUNDLEMAX below to set the limit on number of chained packets)
+* The current default is 0x600 or 1536. Experiments show that
+* the value should probably stay within the 0x200 - 0x1000.
+*
+* BUNDLEMAX -
+* This sets the maximum number of frames that will be bundled. In
+* some situations, such as the TCP windowing algorithm, it may be
+* better to limit the growth of the bundle size than let it go as
+* high as it can, because that could cause too much added latency.
+* The default is six, because this is the number of packets in the
+* default TCP window size. A value of 1 would make CPUSaver indicate
+* an interrupt for every frame received. If you do not want to put
+* a limit on the bundle size, set this value to xFFFF.
+*
+* BUNDLESMALL -
+* This contains a bit-mask describing the minimum size frame that
+* will be bundled. The default masks the lower 7 bits, which means
+* that any frame less than 128 bytes in length will not be bundled,
+* but will instead immediately generate an interrupt. This does
+* not affect the current bundle in any way. Any frame that is 128
+* bytes or large will be bundled normally. This feature is meant
+* to provide immediate indication of ACK frames in a TCP environment.
+* Customers were seeing poor performance when a machine with CPUSaver
+* enabled was sending but not receiving. The delay introduced when
+* the ACKs were received was enough to reduce total throughput, because
+* the sender would sit idle until the ACK was finally seen.
+*
+* The current default is 0xFF80, which masks out the lower 7 bits.
+* This means that any frame which is x7F (127) bytes or smaller
+* will cause an immediate interrupt. Because this value must be a
+* bit mask, there are only a few valid values that can be used. To
+* turn this feature off, the driver can write the value xFFFF to the
+* lower word of this instruction (in the same way that the other
+* parameters are used). Likewise, a value of 0xF800 (2047) would
+* cause an interrupt to be generated for every frame, because all
+* standard Ethernet frames are <= 2047 bytes in length.
+*************************************************************************/
+
+/* if you wish to disable the ucode functionality, while maintaining the
+ * workarounds it provides, set the following defines to:
+ * BUNDLESMALL 0
+ * BUNDLEMAX 1
+ * INTDELAY 1
+ */
#define BUNDLESMALL 1
-#define BUNDLEMAX 50
-#define INTDELAY 15000
-
- opts = ucode_opts;
+#define BUNDLEMAX (u16)6
+#define INTDELAY (u16)1536 /* 0x600 */
/* do not load u-code for ICH devices */
if (nic->flags & ich)
- return;
+ goto noloaducode;
/* Search for ucode match against h/w rev_id */
- while (opts->mac) {
- if (nic->mac == opts->mac) {
- int i;
- u32 *ucode = opts->ucode;
-
- /* Insert user-tunable settings */
- ucode[opts->timer_dword] &= 0xFFFF0000;
- ucode[opts->timer_dword] |=
- (u16) INTDELAY;
- ucode[opts->bundle_dword] &= 0xFFFF0000;
- ucode[opts->bundle_dword] |= (u16) BUNDLEMAX;
- ucode[opts->min_size_dword] &= 0xFFFF0000;
- ucode[opts->min_size_dword] |=
- (BUNDLESMALL) ? 0xFFFF : 0xFF80;
-
- for(i = 0; i < UCODE_SIZE; i++)
- cb->u.ucode[i] = cpu_to_le32(ucode[i]);
- cb->command = cpu_to_le16(cb_ucode);
- return;
- }
- opts++;
+ for (opts = ucode_opts; opts->mac; opts++) {
+ int i;
+ u32 *ucode = opts->ucode;
+ if (nic->mac != opts->mac)
+ continue;
+
+ /* Insert user-tunable settings */
+ ucode[opts->timer_dword] &= 0xFFFF0000;
+ ucode[opts->timer_dword] |= INTDELAY;
+ ucode[opts->bundle_dword] &= 0xFFFF0000;
+ ucode[opts->bundle_dword] |= BUNDLEMAX;
+ ucode[opts->min_size_dword] &= 0xFFFF0000;
+ ucode[opts->min_size_dword] |= (BUNDLESMALL) ? 0xFFFF : 0xFF80;
+
+ for (i = 0; i < UCODE_SIZE; i++)
+ cb->u.ucode[i] = cpu_to_le32(ucode[i]);
+ cb->command = cpu_to_le16(cb_ucode);
+ return;
}
+noloaducode:
cb->command = cpu_to_le16(cb_nop);
}
if(pci_dma_mapping_error(rx->dma_addr)) {
dev_kfree_skb_any(rx->skb);
- rx->skb = 0;
+ rx->skb = NULL;
rx->dma_addr = 0;
return -ENOMEM;
}
if((err = e100_hw_init(nic)))
goto err_clean_cbs;
e100_set_multicast_list(nic->netdev);
- e100_start_receiver(nic, 0);
+ e100_start_receiver(nic, NULL);
mod_timer(&nic->watchdog, jiffies);
if((err = request_irq(nic->pdev->irq, e100_intr, SA_SHIRQ,
nic->netdev->name, nic->netdev)))
mdio_write(nic->netdev, nic->mii.phy_id, MII_BMCR,
BMCR_LOOPBACK);
- e100_start_receiver(nic, 0);
+ e100_start_receiver(nic, NULL);
if(!(skb = dev_alloc_skb(ETH_DATA_LEN))) {
err = -ENOMEM;
.phys_id = e100_phys_id,
.get_stats_count = e100_get_stats_count,
.get_ethtool_stats = e100_get_ethtool_stats,
+ .get_perm_addr = ethtool_op_get_perm_addr,
};
static int e100_do_ioctl(struct net_device *netdev, struct ifreq *ifr, int cmd)
e100_phy_init(nic);
memcpy(netdev->dev_addr, nic->eeprom, ETH_ALEN);
- if(!is_valid_ether_addr(netdev->dev_addr)) {
+ memcpy(netdev->perm_addr, nic->eeprom, ETH_ALEN);
+ if(!is_valid_ether_addr(netdev->perm_addr)) {
DPRINTK(PROBE, ERR, "Invalid MAC address from "
"EEPROM, aborting.\n");
err = -EAGAIN;
projects / karo-tx-linux.git / blobdiff