*
* GPL LICENSE SUMMARY
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of version 2 of the GNU General Public License as
*
* BSD LICENSE
*
- * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved.
+ * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
/* Bluetooth device coexistance config command */
REPLY_BT_CONFIG = 0x9b,
- /* 4965 Statistics */
+ /* Statistics */
REPLY_STATISTICS_CMD = 0x9c,
STATISTICS_NOTIFICATION = 0x9d,
/******************************************************************************
* (0)
* Commonly used structures and definitions:
- * Command header, rate_n_flags
+ * Command header, rate_n_flags, txpower
*
*****************************************************************************/
#define RATE_MCS_ANT_AB_MSK 0xc000
+/**
+ * struct iwl4965_tx_power - txpower format used in REPLY_SCAN_CMD
+ *
+ * Scan uses only one transmitter, so only one analog/dsp gain pair is needed.
+ */
+struct iwl4965_tx_power {
+ u8 tx_gain; /* gain for analog radio */
+ u8 dsp_atten; /* gain for DSP */
+} __attribute__ ((packed));
+
+#define POWER_TABLE_NUM_ENTRIES 33
+#define POWER_TABLE_NUM_HT_OFDM_ENTRIES 32
+#define POWER_TABLE_CCK_ENTRY 32
+
+/**
+ * union iwl4965_tx_power_dual_stream
+ *
+ * Host format used for REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
+ * Use __le32 version (struct tx_power_dual_stream) when building command.
+ *
+ * Driver provides radio gain and DSP attenuation settings to device in pairs,
+ * one value for each transmitter chain. The first value is for transmitter A,
+ * second for transmitter B.
+ *
+ * For SISO bit rates, both values in a pair should be identical.
+ * For MIMO rates, one value may be different from the other,
+ * in order to balance the Tx output between the two transmitters.
+ *
+ * See more details in doc for TXPOWER in iwl-4965-hw.h.
+ */
+union iwl4965_tx_power_dual_stream {
+ struct {
+ u8 radio_tx_gain[2];
+ u8 dsp_predis_atten[2];
+ } s;
+ u32 dw;
+};
+
+/**
+ * struct tx_power_dual_stream
+ *
+ * Table entries in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
+ *
+ * Same format as iwl_tx_power_dual_stream, but __le32
+ */
+struct tx_power_dual_stream {
+ __le32 dw;
+} __attribute__ ((packed));
+
+/**
+ * struct iwl4965_tx_power_db
+ *
+ * Entire table within REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
+ */
+struct iwl4965_tx_power_db {
+ struct tx_power_dual_stream power_tbl[POWER_TABLE_NUM_ENTRIES];
+} __attribute__ ((packed));
+
+
/******************************************************************************
* (0a)
* Alive and Error Commands & Responses:
};
-#define RXON_RX_CHAIN_DRIVER_FORCE_MSK __constant_cpu_to_le16(0x1<<0)
-#define RXON_RX_CHAIN_VALID_MSK __constant_cpu_to_le16(0x7<<1)
+#define RXON_RX_CHAIN_DRIVER_FORCE_MSK __constant_cpu_to_le16(0x1 << 0)
+#define RXON_RX_CHAIN_VALID_MSK __constant_cpu_to_le16(0x7 << 1)
#define RXON_RX_CHAIN_VALID_POS (1)
-#define RXON_RX_CHAIN_FORCE_SEL_MSK __constant_cpu_to_le16(0x7<<4)
+#define RXON_RX_CHAIN_FORCE_SEL_MSK __constant_cpu_to_le16(0x7 << 4)
#define RXON_RX_CHAIN_FORCE_SEL_POS (4)
-#define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK __constant_cpu_to_le16(0x7<<7)
+#define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK __constant_cpu_to_le16(0x7 << 7)
#define RXON_RX_CHAIN_FORCE_MIMO_SEL_POS (7)
-#define RXON_RX_CHAIN_CNT_MSK __constant_cpu_to_le16(0x3<<10)
+#define RXON_RX_CHAIN_CNT_MSK __constant_cpu_to_le16(0x3 << 10)
#define RXON_RX_CHAIN_CNT_POS (10)
-#define RXON_RX_CHAIN_MIMO_CNT_MSK __constant_cpu_to_le16(0x3<<12)
+#define RXON_RX_CHAIN_MIMO_CNT_MSK __constant_cpu_to_le16(0x3 << 12)
#define RXON_RX_CHAIN_MIMO_CNT_POS (12)
-#define RXON_RX_CHAIN_MIMO_FORCE_MSK __constant_cpu_to_le16(0x1<<14)
+#define RXON_RX_CHAIN_MIMO_FORCE_MSK __constant_cpu_to_le16(0x1 << 14)
#define RXON_RX_CHAIN_MIMO_FORCE_POS (14)
/* rx_config flags */
/* HT flags */
#define RXON_FLG_CTRL_CHANNEL_LOC_POS (22)
-#define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK __constant_cpu_to_le32(0x1<<22)
+#define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK __constant_cpu_to_le32(0x1 << 22)
#define RXON_FLG_HT_OPERATING_MODE_POS (23)
-#define RXON_FLG_HT_PROT_MSK __constant_cpu_to_le32(0x1<<23)
-#define RXON_FLG_FAT_PROT_MSK __constant_cpu_to_le32(0x2<<23)
+#define RXON_FLG_HT_PROT_MSK __constant_cpu_to_le32(0x1 << 23)
+#define RXON_FLG_FAT_PROT_MSK __constant_cpu_to_le32(0x2 << 23)
#define RXON_FLG_CHANNEL_MODE_POS (25)
-#define RXON_FLG_CHANNEL_MODE_MSK __constant_cpu_to_le32(0x3<<25)
-#define RXON_FLG_CHANNEL_MODE_PURE_40_MSK __constant_cpu_to_le32(0x1<<25)
-#define RXON_FLG_CHANNEL_MODE_MIXED_MSK __constant_cpu_to_le32(0x2<<25)
+#define RXON_FLG_CHANNEL_MODE_MSK __constant_cpu_to_le32(0x3 << 25)
+#define RXON_FLG_CHANNEL_MODE_PURE_40_MSK __constant_cpu_to_le32(0x1 << 25)
+#define RXON_FLG_CHANNEL_MODE_MIXED_MSK __constant_cpu_to_le32(0x2 << 25)
/* rx_config filter flags */
/* accept all data frames */
/* transfer to host non bssid beacons in associated state */
#define RXON_FILTER_BCON_AWARE_MSK __constant_cpu_to_le32(1 << 6)
-/*
+/**
* REPLY_RXON = 0x10 (command, has simple generic response)
+ *
+ * RXON tunes the radio tuner to a service channel, and sets up a number
+ * of parameters that are used primarily for Rx, but also for Tx operations.
+ *
+ * NOTE: When tuning to a new channel, driver must set the
+ * RXON_FILTER_ASSOC_MSK to 0. This will clear station-dependent
+ * info within the device, including the station tables, tx retry
+ * rate tables, and txpower tables. Driver must build a new station
+ * table and txpower table before transmitting anything on the RXON
+ * channel.
+ *
+ * NOTE: All RXONs wipe clean the internal txpower table. Driver must
+ * issue a new REPLY_TX_PWR_TABLE_CMD after each REPLY_RXON (0x10),
+ * regardless of whether RXON_FILTER_ASSOC_MSK is set.
*/
struct iwl4965_rxon_cmd {
u8 node_addr[6];
__le16 reserved;
} __attribute__ ((packed));
-struct iwl4965_tx_power {
- u8 tx_gain; /* gain for analog radio */
- u8 dsp_atten; /* gain for DSP */
-} __attribute__ ((packed));
-
-#define POWER_TABLE_NUM_ENTRIES 33
-#define POWER_TABLE_NUM_HT_OFDM_ENTRIES 32
-#define POWER_TABLE_CCK_ENTRY 32
-
-union iwl4965_tx_power_dual_stream {
- struct {
- u8 radio_tx_gain[2];
- u8 dsp_predis_atten[2];
- } s;
- u32 dw;
-};
-
-struct tx_power_dual_stream {
- __le32 dw;
-} __attribute__ ((packed));
-
-struct iwl4965_tx_power_db {
- struct tx_power_dual_stream power_tbl[POWER_TABLE_NUM_ENTRIES];
-} __attribute__ ((packed));
-
/*
* REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
*/
* Quality-of-Service (QOS) Commands & Responses:
*
*****************************************************************************/
+
+/**
+ * struct iwl_ac_qos -- QOS timing params for REPLY_QOS_PARAM
+ * One for each of 4 EDCA access categories in struct iwl_qosparam_cmd
+ *
+ * @cw_min: Contention window, start value in numbers of slots.
+ * Should be a power-of-2, minus 1. Device's default is 0x0f.
+ * @cw_max: Contention window, max value in numbers of slots.
+ * Should be a power-of-2, minus 1. Device's default is 0x3f.
+ * @aifsn: Number of slots in Arbitration Interframe Space (before
+ * performing random backoff timing prior to Tx). Device default 1.
+ * @edca_txop: Length of Tx opportunity, in uSecs. Device default is 0.
+ *
+ * Device will automatically increase contention window by (2*CW) + 1 for each
+ * transmission retry. Device uses cw_max as a bit mask, ANDed with new CW
+ * value, to cap the CW value.
+ */
struct iwl4965_ac_qos {
__le16 cw_min;
__le16 cw_max;
#define QOS_PARAM_FLG_TGN_MSK __constant_cpu_to_le32(0x02)
#define QOS_PARAM_FLG_TXOP_TYPE_MSK __constant_cpu_to_le32(0x10)
-/*
- * TXFIFO Queue number defines
- */
-/* number of Access categories (AC) (EDCA), queues 0..3 */
+/* Number of Access Categories (AC) (EDCA), queues 0..3 */
#define AC_NUM 4
/*
* REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
+ *
+ * This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
+ * 0: Background, 1: Best Effort, 2: Video, 3: Voice.
*/
struct iwl4965_qosparam_cmd {
__le32 qos_flags;
/*
* Multi station support
*/
+
+/* Special, dedicated locations within device's station table */
#define IWL_AP_ID 0
#define IWL_MULTICAST_ID 1
#define IWL_STA_ID 2
-
-#define IWL3945_BROADCAST_ID 24
-#define IWL3945_STATION_COUNT 25
-
#define IWL4965_BROADCAST_ID 31
#define IWL4965_STATION_COUNT 32
#define IWL_STATION_COUNT 32 /* MAX(3945,4965)*/
#define IWL_INVALID_STATION 255
-#define STA_FLG_PWR_SAVE_MSK __constant_cpu_to_le32(1<<8);
+#define STA_FLG_PWR_SAVE_MSK __constant_cpu_to_le32(1 << 8);
#define STA_FLG_RTS_MIMO_PROT_MSK __constant_cpu_to_le32(1 << 17)
#define STA_FLG_AGG_MPDU_8US_MSK __constant_cpu_to_le32(1 << 18)
#define STA_FLG_MAX_AGG_SIZE_POS (19)
#define STA_FLG_AGG_MPDU_DENSITY_POS (23)
#define STA_FLG_AGG_MPDU_DENSITY_MSK __constant_cpu_to_le32(7 << 23)
+/* Use in mode field. 1: modify existing entry, 0: add new station entry */
#define STA_CONTROL_MODIFY_MSK 0x01
/* key flags __le16*/
-#define STA_KEY_FLG_ENCRYPT_MSK __constant_cpu_to_le16(0x7)
-#define STA_KEY_FLG_NO_ENC __constant_cpu_to_le16(0x0)
-#define STA_KEY_FLG_WEP __constant_cpu_to_le16(0x1)
-#define STA_KEY_FLG_CCMP __constant_cpu_to_le16(0x2)
-#define STA_KEY_FLG_TKIP __constant_cpu_to_le16(0x3)
+#define STA_KEY_FLG_ENCRYPT_MSK __constant_cpu_to_le16(0x0007)
+#define STA_KEY_FLG_NO_ENC __constant_cpu_to_le16(0x0000)
+#define STA_KEY_FLG_WEP __constant_cpu_to_le16(0x0001)
+#define STA_KEY_FLG_CCMP __constant_cpu_to_le16(0x0002)
+#define STA_KEY_FLG_TKIP __constant_cpu_to_le16(0x0003)
#define STA_KEY_FLG_KEYID_POS 8
#define STA_KEY_FLG_INVALID __constant_cpu_to_le16(0x0800)
+/* wep key is either from global key (0) or from station info array (1) */
+#define STA_KEY_FLG_MAP_KEY_MSK __constant_cpu_to_le16(0x0008)
+
+/* wep key in STA: 5-bytes (0) or 13-bytes (1) */
+#define STA_KEY_FLG_KEY_SIZE_MSK __constant_cpu_to_le16(0x1000)
+#define STA_KEY_MULTICAST_MSK __constant_cpu_to_le16(0x4000)
-/* modify flags */
+/* Flags indicate whether to modify vs. don't change various station params */
#define STA_MODIFY_KEY_MASK 0x01
#define STA_MODIFY_TID_DISABLE_TX 0x02
#define STA_MODIFY_TX_RATE_MSK 0x04
#define STA_MODIFY_ADDBA_TID_MSK 0x08
#define STA_MODIFY_DELBA_TID_MSK 0x10
+
+/* Receiver address (actually, Rx station's index into station table),
+ * combined with Traffic ID (QOS priority), in format used by Tx Scheduler */
#define BUILD_RAxTID(sta_id, tid) (((sta_id) << 4) + (tid))
struct iwl4965_keyinfo {
u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
u8 reserved1;
__le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
- __le16 reserved2;
+ u8 key_offset;
+ u8 reserved2;
u8 key[16]; /* 16-byte unicast decryption key */
} __attribute__ ((packed));
+/**
+ * struct sta_id_modify
+ * @addr[ETH_ALEN]: station's MAC address
+ * @sta_id: index of station in uCode's station table
+ * @modify_mask: STA_MODIFY_*, 1: modify, 0: don't change
+ *
+ * Driver selects unused table index when adding new station,
+ * or the index to a pre-existing station entry when modifying that station.
+ * Some indexes have special purposes (IWL_AP_ID, index 0, is for AP).
+ *
+ * modify_mask flags select which parameters to modify vs. leave alone.
+ */
struct sta_id_modify {
u8 addr[ETH_ALEN];
__le16 reserved1;
/*
* REPLY_ADD_STA = 0x18 (command)
+ *
+ * The device contains an internal table of per-station information,
+ * with info on security keys, aggregation parameters, and Tx rates for
+ * initial Tx attempt and any retries (4965 uses REPLY_TX_LINK_QUALITY_CMD,
+ * 3945 uses REPLY_RATE_SCALE to set up rate tables).
+ *
+ * REPLY_ADD_STA sets up the table entry for one station, either creating
+ * a new entry, or modifying a pre-existing one.
+ *
+ * NOTE: RXON command (without "associated" bit set) wipes the station table
+ * clean. Moving into RF_KILL state does this also. Driver must set up
+ * new station table before transmitting anything on the RXON channel
+ * (except active scans or active measurements; those commands carry
+ * their own txpower/rate setup data).
+ *
+ * When getting started on a new channel, driver must set up the
+ * IWL_BROADCAST_ID entry (last entry in the table). For a client
+ * station in a BSS, once an AP is selected, driver sets up the AP STA
+ * in the IWL_AP_ID entry (1st entry in the table). BROADCAST and AP
+ * are all that are needed for a BSS client station. If the device is
+ * used as AP, or in an IBSS network, driver must set up station table
+ * entries for all STAs in network, starting with index IWL_STA_ID.
*/
struct iwl4965_addsta_cmd {
- u8 mode;
+ u8 mode; /* 1: modify existing, 0: add new station */
u8 reserved[3];
struct sta_id_modify sta;
struct iwl4965_keyinfo key;
- __le32 station_flags;
- __le32 station_flags_msk;
+ __le32 station_flags; /* STA_FLG_* */
+ __le32 station_flags_msk; /* STA_FLG_* */
+
+ /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
+ * corresponding to bit (e.g. bit 5 controls TID 5).
+ * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
__le16 tid_disable_tx;
+
__le16 reserved1;
+
+ /* TID for which to add block-ack support.
+ * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
u8 add_immediate_ba_tid;
+
+ /* TID for which to remove block-ack support.
+ * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
u8 remove_immediate_ba_tid;
+
+ /* Starting Sequence Number for added block-ack support.
+ * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
__le16 add_immediate_ba_ssn;
+
__le32 reserved2;
} __attribute__ ((packed));
+#define ADD_STA_SUCCESS_MSK 0x1
+#define ADD_STA_NO_ROOM_IN_TABLE 0x2
+#define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
+#define ADD_STA_MODIFY_NON_EXIST_STA 0x8
/*
* REPLY_ADD_STA = 0x18 (response)
*/
struct iwl4965_add_sta_resp {
- u8 status;
+ u8 status; /* ADD_STA_* */
} __attribute__ ((packed));
-#define ADD_STA_SUCCESS_MSK 0x1
/******************************************************************************
* (4)
u8 payload[0];
} __attribute__ ((packed));
-#define RX_RES_STATUS_NO_CRC32_ERROR __constant_cpu_to_le32(1 << 0)
-#define RX_RES_STATUS_NO_RXE_OVERFLOW __constant_cpu_to_le32(1 << 1)
+#define RX_RES_STATUS_NO_CRC32_ERROR __constant_cpu_to_le32(1 << 0)
+#define RX_RES_STATUS_NO_RXE_OVERFLOW __constant_cpu_to_le32(1 << 1)
-#define RX_RES_PHY_FLAGS_BAND_24_MSK __constant_cpu_to_le16(1 << 0)
-#define RX_RES_PHY_FLAGS_MOD_CCK_MSK __constant_cpu_to_le16(1 << 1)
-#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK __constant_cpu_to_le16(1 << 2)
-#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK __constant_cpu_to_le16(1 << 3)
-#define RX_RES_PHY_FLAGS_ANTENNA_MSK __constant_cpu_to_le16(0xf0)
+#define RX_RES_PHY_FLAGS_BAND_24_MSK __constant_cpu_to_le16(1 << 0)
+#define RX_RES_PHY_FLAGS_MOD_CCK_MSK __constant_cpu_to_le16(1 << 1)
+#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK __constant_cpu_to_le16(1 << 2)
+#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK __constant_cpu_to_le16(1 << 3)
+#define RX_RES_PHY_FLAGS_ANTENNA_MSK __constant_cpu_to_le16(0xf0)
-#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
-#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
-#define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
-#define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
-#define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
+#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
+#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
+#define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
+#define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
+#define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
-#define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
-#define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
-#define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
-#define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
-#define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
+#define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
+#define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
+#define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
+#define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
+#define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
struct iwl4965_rx_frame_end {
__le32 status;
__le16 channel; /* channel number */
__le16 non_cfg_phy[RX_RES_PHY_CNT]; /* upto 14 phy entries */
__le32 reserved2;
- __le32 rate_n_flags;
- __le16 byte_count; /* frame's byte-count */
+ __le32 rate_n_flags; /* RATE_MCS_* */
+ __le16 byte_count; /* frame's byte-count */
__le16 reserved3;
} __attribute__ ((packed));
* (5)
* Tx Commands & Responses:
*
+ * Driver must place each REPLY_TX command into one of the prioritized Tx
+ * queues in host DRAM, shared between driver and device (see comments for
+ * SCD registers and Tx/Rx Queues). When the device's Tx scheduler and uCode
+ * are preparing to transmit, the device pulls the Tx command over the PCI
+ * bus via one of the device's Tx DMA channels, to fill an internal FIFO
+ * from which data will be transmitted.
+ *
+ * uCode handles all timing and protocol related to control frames
+ * (RTS/CTS/ACK), based on flags in the Tx command. uCode and Tx scheduler
+ * handle reception of block-acks; uCode updates the host driver via
+ * REPLY_COMPRESSED_BA (4965).
+ *
+ * uCode handles retrying Tx when an ACK is expected but not received.
+ * This includes trying lower data rates than the one requested in the Tx
+ * command, as set up by the REPLY_RATE_SCALE (for 3945) or
+ * REPLY_TX_LINK_QUALITY_CMD (4965).
+ *
+ * Driver sets up transmit power for various rates via REPLY_TX_PWR_TABLE_CMD.
+ * This command must be executed after every RXON command, before Tx can occur.
*****************************************************************************/
-/* Tx flags */
+/* REPLY_TX Tx flags field */
+
+/* 1: Use Request-To-Send protocol before this frame.
+ * Mutually exclusive vs. TX_CMD_FLG_CTS_MSK. */
#define TX_CMD_FLG_RTS_MSK __constant_cpu_to_le32(1 << 1)
+
+/* 1: Transmit Clear-To-Send to self before this frame.
+ * Driver should set this for AUTH/DEAUTH/ASSOC-REQ/REASSOC mgmnt frames.
+ * Mutually exclusive vs. TX_CMD_FLG_RTS_MSK. */
#define TX_CMD_FLG_CTS_MSK __constant_cpu_to_le32(1 << 2)
+
+/* 1: Expect ACK from receiving station
+ * 0: Don't expect ACK (MAC header's duration field s/b 0)
+ * Set this for unicast frames, but not broadcast/multicast. */
#define TX_CMD_FLG_ACK_MSK __constant_cpu_to_le32(1 << 3)
+
+/* For 4965:
+ * 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
+ * Tx command's initial_rate_index indicates first rate to try;
+ * uCode walks through table for additional Tx attempts.
+ * 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
+ * This rate will be used for all Tx attempts; it will not be scaled. */
#define TX_CMD_FLG_STA_RATE_MSK __constant_cpu_to_le32(1 << 4)
+
+/* 1: Expect immediate block-ack.
+ * Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
#define TX_CMD_FLG_IMM_BA_RSP_MASK __constant_cpu_to_le32(1 << 6)
+
+/* 1: Frame requires full Tx-Op protection.
+ * Set this if either RTS or CTS Tx Flag gets set. */
#define TX_CMD_FLG_FULL_TXOP_PROT_MSK __constant_cpu_to_le32(1 << 7)
+
+/* Tx antenna selection field; used only for 3945, reserved (0) for 4965.
+ * Set field to "0" to allow 3945 uCode to select antenna (normal usage). */
#define TX_CMD_FLG_ANT_SEL_MSK __constant_cpu_to_le32(0xf00)
#define TX_CMD_FLG_ANT_A_MSK __constant_cpu_to_le32(1 << 8)
#define TX_CMD_FLG_ANT_B_MSK __constant_cpu_to_le32(1 << 9)
-/* ucode ignores BT priority for this frame */
+/* 1: Ignore Bluetooth priority for this frame.
+ * 0: Delay Tx until Bluetooth device is done (normal usage). */
#define TX_CMD_FLG_BT_DIS_MSK __constant_cpu_to_le32(1 << 12)
-/* ucode overrides sequence control */
+/* 1: uCode overrides sequence control field in MAC header.
+ * 0: Driver provides sequence control field in MAC header.
+ * Set this for management frames, non-QOS data frames, non-unicast frames,
+ * and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
#define TX_CMD_FLG_SEQ_CTL_MSK __constant_cpu_to_le32(1 << 13)
-/* signal that this frame is non-last MPDU */
+/* 1: This frame is non-last MPDU; more fragments are coming.
+ * 0: Last fragment, or not using fragmentation. */
#define TX_CMD_FLG_MORE_FRAG_MSK __constant_cpu_to_le32(1 << 14)
-/* calculate TSF in outgoing frame */
+/* 1: uCode calculates and inserts Timestamp Function (TSF) in outgoing frame.
+ * 0: No TSF required in outgoing frame.
+ * Set this for transmitting beacons and probe responses. */
#define TX_CMD_FLG_TSF_MSK __constant_cpu_to_le32(1 << 16)
-/* activate TX calibration. */
-#define TX_CMD_FLG_CALIB_MSK __constant_cpu_to_le32(1 << 17)
-
-/* signals that 2 bytes pad was inserted
- after the MAC header */
+/* 1: Driver inserted 2 bytes pad after the MAC header, for (required) dword
+ * alignment of frame's payload data field.
+ * 0: No pad
+ * Set this for MAC headers with 26 or 30 bytes, i.e. those with QOS or ADDR4
+ * field (but not both). Driver must align frame data (i.e. data following
+ * MAC header) to DWORD boundary. */
#define TX_CMD_FLG_MH_PAD_MSK __constant_cpu_to_le32(1 << 20)
/* HCCA-AP - disable duration overwriting. */
#define TX_CMD_FLG_DUR_MSK __constant_cpu_to_le32(1 << 25)
+
/*
* TX command security control
*/
#define TX_CMD_SEC_KEY128 0x08
/*
- * TX command Frame life time
+ * 4965 uCode updates these Tx attempt count values in host DRAM.
+ * Used for managing Tx retries when expecting block-acks.
+ * Driver should set these fields to 0.
*/
-
struct iwl4965_dram_scratch {
- u8 try_cnt;
- u8 bt_kill_cnt;
+ u8 try_cnt; /* Tx attempts */
+ u8 bt_kill_cnt; /* Tx attempts blocked by Bluetooth device */
__le16 reserved;
} __attribute__ ((packed));
* REPLY_TX = 0x1c (command)
*/
struct iwl4965_tx_cmd {
+ /*
+ * MPDU byte count:
+ * MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
+ * + 8 byte IV for CCM or TKIP (not used for WEP)
+ * + Data payload
+ * + 8-byte MIC (not used for CCM/WEP)
+ * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
+ * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
+ * Range: 14-2342 bytes.
+ */
__le16 len;
+
+ /*
+ * MPDU or MSDU byte count for next frame.
+ * Used for fragmentation and bursting, but not 11n aggregation.
+ * Same as "len", but for next frame. Set to 0 if not applicable.
+ */
__le16 next_frame_len;
- __le32 tx_flags;
+
+ __le32 tx_flags; /* TX_CMD_FLG_* */
+
+ /* 4965's uCode may modify this field of the Tx command (in host DRAM!).
+ * Driver must also set dram_lsb_ptr and dram_msb_ptr in this cmd. */
struct iwl4965_dram_scratch scratch;
- __le32 rate_n_flags;
+
+ /* Rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is cleared. */
+ __le32 rate_n_flags; /* RATE_MCS_* */
+
+ /* Index of destination station in uCode's station table */
u8 sta_id;
- u8 sec_ctl;
+
+ /* Type of security encryption: CCM or TKIP */
+ u8 sec_ctl; /* TX_CMD_SEC_* */
+
+ /*
+ * Index into rate table (see REPLY_TX_LINK_QUALITY_CMD) for initial
+ * Tx attempt, if TX_CMD_FLG_STA_RATE_MSK is set. Normally "0" for
+ * data frames, this field may be used to selectively reduce initial
+ * rate (via non-0 value) for special frames (e.g. management), while
+ * still supporting rate scaling for all frames.
+ */
u8 initial_rate_index;
u8 reserved;
u8 key[16];
__le32 life_time;
__le32 attempt;
} stop_time;
+
+ /* Host DRAM physical address pointer to "scratch" in this command.
+ * Must be dword aligned. "0" in dram_lsb_ptr disables usage. */
__le32 dram_lsb_ptr;
u8 dram_msb_ptr;
+
u8 rts_retry_limit; /*byte 50 */
u8 data_retry_limit; /*byte 51 */
u8 tid_tspec;
__le16 pm_frame_timeout;
__le16 attempt_duration;
} timeout;
+
+ /*
+ * Duration of EDCA burst Tx Opportunity, in 32-usec units.
+ * Set this if txop time is not specified by HCCA protocol (e.g. by AP).
+ */
__le16 driver_txop;
+
+ /*
+ * MAC header goes here, followed by 2 bytes padding if MAC header
+ * length is 26 or 30 bytes, followed by payload data
+ */
u8 payload[0];
struct ieee80211_hdr hdr[0];
} __attribute__ ((packed));
};
/* *******************************
- * TX aggregation state
+ * TX aggregation status
******************************* */
enum {
AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK | \
AGG_TX_STATE_LAST_SENT_BT_KILL_MSK)
+/* # tx attempts for first frame in aggregation */
#define AGG_TX_STATE_TRY_CNT_POS 12
#define AGG_TX_STATE_TRY_CNT_MSK 0xf000
+/* Command ID and sequence number of Tx command for this frame */
#define AGG_TX_STATE_SEQ_NUM_POS 16
#define AGG_TX_STATE_SEQ_NUM_MSK 0xffff0000
/*
* REPLY_TX = 0x1c (response)
+ *
+ * This response may be in one of two slightly different formats, indicated
+ * by the frame_count field:
+ *
+ * 1) No aggregation (frame_count == 1). This reports Tx results for
+ * a single frame. Multiple attempts, at various bit rates, may have
+ * been made for this frame.
+ *
+ * 2) Aggregation (frame_count > 1). This reports Tx results for
+ * 2 or more frames that used block-acknowledge. All frames were
+ * transmitted at same rate. Rate scaling may have been used if first
+ * frame in this new agg block failed in previous agg block(s).
+ *
+ * Note that, for aggregation, ACK (block-ack) status is not delivered here;
+ * block-ack has not been received by the time the 4965 records this status.
+ * This status relates to reasons the tx might have been blocked or aborted
+ * within the sending station (this 4965), rather than whether it was
+ * received successfully by the destination station.
*/
struct iwl4965_tx_resp {
u8 frame_count; /* 1 no aggregation, >1 aggregation */
- u8 bt_kill_count;
+ u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
+ u8 failure_rts; /* # failures due to unsuccessful RTS */
+ u8 failure_frame; /* # failures due to no ACK (unused for agg) */
+
+ /* For non-agg: Rate at which frame was successful.
+ * For agg: Rate at which all frames were transmitted. */
+ __le32 rate_n_flags; /* RATE_MCS_* */
+
+ /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
+ * For agg: RTS + CTS + aggregation tx time + block-ack time. */
+ __le16 wireless_media_time; /* uSecs */
+
+ __le16 reserved;
+ __le32 pa_power1; /* RF power amplifier measurement (not used) */
+ __le32 pa_power2;
+
+ /*
+ * For non-agg: frame status TX_STATUS_*
+ * For agg: status of 1st frame, AGG_TX_STATE_*; other frame status
+ * fields follow this one, up to frame_count.
+ * Bit fields:
+ * 11- 0: AGG_TX_STATE_* status code
+ * 15-12: Retry count for 1st frame in aggregation (retries
+ * occur if tx failed for this frame when it was a
+ * member of a previous aggregation block). If rate
+ * scaling is used, retry count indicates the rate
+ * table entry used for all frames in the new agg.
+ * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
+ */
+ __le32 status; /* TX status (for aggregation status of 1st frame) */
+} __attribute__ ((packed));
+
+struct agg_tx_status {
+ __le16 status;
+ __le16 sequence;
+} __attribute__ ((packed));
+
+struct iwl4965_tx_resp_agg {
+ u8 frame_count; /* 1 no aggregation, >1 aggregation */
+ u8 reserved1;
u8 failure_rts;
u8 failure_frame;
__le32 rate_n_flags;
__le16 wireless_media_time;
- __le16 reserved;
+ __le16 reserved3;
__le32 pa_power1;
__le32 pa_power2;
- __le32 status; /* TX status (for aggregation status of 1st frame) */
+ struct agg_tx_status status; /* TX status (for aggregation status */
+ /* of 1st frame) */
} __attribute__ ((packed));
/*
* REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
+ *
+ * Reports Block-Acknowledge from recipient station
*/
struct iwl4965_compressed_ba_resp {
__le32 sta_addr_lo32;
__le16 sta_addr_hi16;
__le16 reserved;
+
+ /* Index of recipient (BA-sending) station in uCode's station table */
u8 sta_id;
u8 tid;
- __le16 ba_seq_ctl;
- __le32 ba_bitmap0;
- __le32 ba_bitmap1;
+ __le16 seq_ctl;
+ __le64 bitmap;
__le16 scd_flow;
__le16 scd_ssn;
} __attribute__ ((packed));
/*
* REPLY_TX_PWR_TABLE_CMD = 0x97 (command, has simple generic response)
+ *
+ * See details under "TXPOWER" in iwl-4965-hw.h.
*/
struct iwl4965_txpowertable_cmd {
u8 band; /* 0: 5 GHz, 1: 2.4 GHz */
} __attribute__ ((packed));
/*RS_NEW_API: only TLC_RTS remains and moved to bit 0 */
-#define LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK (1<<0)
+#define LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK (1 << 0)
+/* # of EDCA prioritized tx fifos */
#define LINK_QUAL_AC_NUM AC_NUM
+
+/* # entries in rate scale table to support Tx retries */
#define LINK_QUAL_MAX_RETRY_NUM 16
-#define LINK_QUAL_ANT_A_MSK (1<<0)
-#define LINK_QUAL_ANT_B_MSK (1<<1)
+/* Tx antenna selection values */
+#define LINK_QUAL_ANT_A_MSK (1 << 0)
+#define LINK_QUAL_ANT_B_MSK (1 << 1)
#define LINK_QUAL_ANT_MSK (LINK_QUAL_ANT_A_MSK|LINK_QUAL_ANT_B_MSK)
+
+/**
+ * struct iwl4965_link_qual_general_params
+ *
+ * Used in REPLY_TX_LINK_QUALITY_CMD
+ */
struct iwl4965_link_qual_general_params {
u8 flags;
+
+ /* No entries at or above this (driver chosen) index contain MIMO */
u8 mimo_delimiter;
- u8 single_stream_ant_msk;
- u8 dual_stream_ant_msk;
+
+ /* Best single antenna to use for single stream (legacy, SISO). */
+ u8 single_stream_ant_msk; /* LINK_QUAL_ANT_* */
+
+ /* Best antennas to use for MIMO (unused for 4965, assumes both). */
+ u8 dual_stream_ant_msk; /* LINK_QUAL_ANT_* */
+
+ /*
+ * If driver needs to use different initial rates for different
+ * EDCA QOS access categories (as implemented by tx fifos 0-3),
+ * this table will set that up, by indicating the indexes in the
+ * rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table at which to start.
+ * Otherwise, driver should set all entries to 0.
+ *
+ * Entry usage:
+ * 0 = Background, 1 = Best Effort (normal), 2 = Video, 3 = Voice
+ * TX FIFOs above 3 use same value (typically 0) as TX FIFO 3.
+ */
u8 start_rate_index[LINK_QUAL_AC_NUM];
} __attribute__ ((packed));
+/**
+ * struct iwl4965_link_qual_agg_params
+ *
+ * Used in REPLY_TX_LINK_QUALITY_CMD
+ */
struct iwl4965_link_qual_agg_params {
+
+ /* Maximum number of uSec in aggregation.
+ * Driver should set this to 4000 (4 milliseconds). */
__le16 agg_time_limit;
+
+ /*
+ * Number of Tx retries allowed for a frame, before that frame will
+ * no longer be considered for the start of an aggregation sequence
+ * (scheduler will then try to tx it as single frame).
+ * Driver should set this to 3.
+ */
u8 agg_dis_start_th;
+
+ /*
+ * Maximum number of frames in aggregation.
+ * 0 = no limit (default). 1 = no aggregation.
+ * Other values = max # frames in aggregation.
+ */
u8 agg_frame_cnt_limit;
+
__le32 reserved;
} __attribute__ ((packed));
/*
* REPLY_TX_LINK_QUALITY_CMD = 0x4e (command, has simple generic response)
+ *
+ * For 4965 only; 3945 uses REPLY_RATE_SCALE.
+ *
+ * Each station in the 4965's internal station table has its own table of 16
+ * Tx rates and modulation modes (e.g. legacy/SISO/MIMO) for retrying Tx when
+ * an ACK is not received. This command replaces the entire table for
+ * one station.
+ *
+ * NOTE: Station must already be in 4965's station table. Use REPLY_ADD_STA.
+ *
+ * The rate scaling procedures described below work well. Of course, other
+ * procedures are possible, and may work better for particular environments.
+ *
+ *
+ * FILLING THE RATE TABLE
+ *
+ * Given a particular initial rate and mode, as determined by the rate
+ * scaling algorithm described below, the Linux driver uses the following
+ * formula to fill the rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table in the
+ * Link Quality command:
+ *
+ *
+ * 1) If using High-throughput (HT) (SISO or MIMO) initial rate:
+ * a) Use this same initial rate for first 3 entries.
+ * b) Find next lower available rate using same mode (SISO or MIMO),
+ * use for next 3 entries. If no lower rate available, switch to
+ * legacy mode (no FAT channel, no MIMO, no short guard interval).
+ * c) If using MIMO, set command's mimo_delimiter to number of entries
+ * using MIMO (3 or 6).
+ * d) After trying 2 HT rates, switch to legacy mode (no FAT channel,
+ * no MIMO, no short guard interval), at the next lower bit rate
+ * (e.g. if second HT bit rate was 54, try 48 legacy), and follow
+ * legacy procedure for remaining table entries.
+ *
+ * 2) If using legacy initial rate:
+ * a) Use the initial rate for only one entry.
+ * b) For each following entry, reduce the rate to next lower available
+ * rate, until reaching the lowest available rate.
+ * c) When reducing rate, also switch antenna selection.
+ * d) Once lowest available rate is reached, repeat this rate until
+ * rate table is filled (16 entries), switching antenna each entry.
+ *
+ *
+ * ACCUMULATING HISTORY
+ *
+ * The rate scaling algorithm for 4965, as implemented in Linux driver, uses
+ * two sets of frame Tx success history: One for the current/active modulation
+ * mode, and one for a speculative/search mode that is being attempted. If the
+ * speculative mode turns out to be more effective (i.e. actual transfer
+ * rate is better), then the driver continues to use the speculative mode
+ * as the new current active mode.
+ *
+ * Each history set contains, separately for each possible rate, data for a
+ * sliding window of the 62 most recent tx attempts at that rate. The data
+ * includes a shifting bitmap of success(1)/failure(0), and sums of successful
+ * and attempted frames, from which the driver can additionally calculate a
+ * success ratio (success / attempted) and number of failures
+ * (attempted - success), and control the size of the window (attempted).
+ * The driver uses the bit map to remove successes from the success sum, as
+ * the oldest tx attempts fall out of the window.
+ *
+ * When the 4965 makes multiple tx attempts for a given frame, each attempt
+ * might be at a different rate, and have different modulation characteristics
+ * (e.g. antenna, fat channel, short guard interval), as set up in the rate
+ * scaling table in the Link Quality command. The driver must determine
+ * which rate table entry was used for each tx attempt, to determine which
+ * rate-specific history to update, and record only those attempts that
+ * match the modulation characteristics of the history set.
+ *
+ * When using block-ack (aggregation), all frames are transmitted at the same
+ * rate, since there is no per-attempt acknowledgement from the destination
+ * station. The Tx response struct iwl_tx_resp indicates the Tx rate in
+ * rate_n_flags field. After receiving a block-ack, the driver can update
+ * history for the entire block all at once.
+ *
+ *
+ * FINDING BEST STARTING RATE:
+ *
+ * When working with a selected initial modulation mode (see below), the
+ * driver attempts to find a best initial rate. The initial rate is the
+ * first entry in the Link Quality command's rate table.
+ *
+ * 1) Calculate actual throughput (success ratio * expected throughput, see
+ * table below) for current initial rate. Do this only if enough frames
+ * have been attempted to make the value meaningful: at least 6 failed
+ * tx attempts, or at least 8 successes. If not enough, don't try rate
+ * scaling yet.
+ *
+ * 2) Find available rates adjacent to current initial rate. Available means:
+ * a) supported by hardware &&
+ * b) supported by association &&
+ * c) within any constraints selected by user
+ *
+ * 3) Gather measured throughputs for adjacent rates. These might not have
+ * enough history to calculate a throughput. That's okay, we might try
+ * using one of them anyway!
+ *
+ * 4) Try decreasing rate if, for current rate:
+ * a) success ratio is < 15% ||
+ * b) lower adjacent rate has better measured throughput ||
+ * c) higher adjacent rate has worse throughput, and lower is unmeasured
+ *
+ * As a sanity check, if decrease was determined above, leave rate
+ * unchanged if:
+ * a) lower rate unavailable
+ * b) success ratio at current rate > 85% (very good)
+ * c) current measured throughput is better than expected throughput
+ * of lower rate (under perfect 100% tx conditions, see table below)
+ *
+ * 5) Try increasing rate if, for current rate:
+ * a) success ratio is < 15% ||
+ * b) both adjacent rates' throughputs are unmeasured (try it!) ||
+ * b) higher adjacent rate has better measured throughput ||
+ * c) lower adjacent rate has worse throughput, and higher is unmeasured
+ *
+ * As a sanity check, if increase was determined above, leave rate
+ * unchanged if:
+ * a) success ratio at current rate < 70%. This is not particularly
+ * good performance; higher rate is sure to have poorer success.
+ *
+ * 6) Re-evaluate the rate after each tx frame. If working with block-
+ * acknowledge, history and statistics may be calculated for the entire
+ * block (including prior history that fits within the history windows),
+ * before re-evaluation.
+ *
+ * FINDING BEST STARTING MODULATION MODE:
+ *
+ * After working with a modulation mode for a "while" (and doing rate scaling),
+ * the driver searches for a new initial mode in an attempt to improve
+ * throughput. The "while" is measured by numbers of attempted frames:
+ *
+ * For legacy mode, search for new mode after:
+ * 480 successful frames, or 160 failed frames
+ * For high-throughput modes (SISO or MIMO), search for new mode after:
+ * 4500 successful frames, or 400 failed frames
+ *
+ * Mode switch possibilities are (3 for each mode):
+ *
+ * For legacy:
+ * Change antenna, try SISO (if HT association), try MIMO (if HT association)
+ * For SISO:
+ * Change antenna, try MIMO, try shortened guard interval (SGI)
+ * For MIMO:
+ * Try SISO antenna A, SISO antenna B, try shortened guard interval (SGI)
+ *
+ * When trying a new mode, use the same bit rate as the old/current mode when
+ * trying antenna switches and shortened guard interval. When switching to
+ * SISO from MIMO or legacy, or to MIMO from SISO or legacy, use a rate
+ * for which the expected throughput (under perfect conditions) is about the
+ * same or slightly better than the actual measured throughput delivered by
+ * the old/current mode.
+ *
+ * Actual throughput can be estimated by multiplying the expected throughput
+ * by the success ratio (successful / attempted tx frames). Frame size is
+ * not considered in this calculation; it assumes that frame size will average
+ * out to be fairly consistent over several samples. The following are
+ * metric values for expected throughput assuming 100% success ratio.
+ * Only G band has support for CCK rates:
+ *
+ * RATE: 1 2 5 11 6 9 12 18 24 36 48 54 60
+ *
+ * G: 7 13 35 58 40 57 72 98 121 154 177 186 186
+ * A: 0 0 0 0 40 57 72 98 121 154 177 186 186
+ * SISO 20MHz: 0 0 0 0 42 42 76 102 124 159 183 193 202
+ * SGI SISO 20MHz: 0 0 0 0 46 46 82 110 132 168 192 202 211
+ * MIMO 20MHz: 0 0 0 0 74 74 123 155 179 214 236 244 251
+ * SGI MIMO 20MHz: 0 0 0 0 81 81 131 164 188 222 243 251 257
+ * SISO 40MHz: 0 0 0 0 77 77 127 160 184 220 242 250 257
+ * SGI SISO 40MHz: 0 0 0 0 83 83 135 169 193 229 250 257 264
+ * MIMO 40MHz: 0 0 0 0 123 123 182 214 235 264 279 285 289
+ * SGI MIMO 40MHz: 0 0 0 0 131 131 191 222 242 270 284 289 293
+ *
+ * After the new mode has been tried for a short while (minimum of 6 failed
+ * frames or 8 successful frames), compare success ratio and actual throughput
+ * estimate of the new mode with the old. If either is better with the new
+ * mode, continue to use the new mode.
+ *
+ * Continue comparing modes until all 3 possibilities have been tried.
+ * If moving from legacy to HT, try all 3 possibilities from the new HT
+ * mode. After trying all 3, a best mode is found. Continue to use this mode
+ * for the longer "while" described above (e.g. 480 successful frames for
+ * legacy), and then repeat the search process.
+ *
*/
struct iwl4965_link_quality_cmd {
+
+ /* Index of destination/recipient station in uCode's station table */
u8 sta_id;
u8 reserved1;
- __le16 control;
+ __le16 control; /* not used */
struct iwl4965_link_qual_general_params general_params;
struct iwl4965_link_qual_agg_params agg_params;
+
+ /*
+ * Rate info; when using rate-scaling, Tx command's initial_rate_index
+ * specifies 1st Tx rate attempted, via index into this table.
+ * 4965 works its way through table when retrying Tx.
+ */
struct {
- __le32 rate_n_flags;
+ __le32 rate_n_flags; /* RATE_MCS_*, IWL_RATE_* */
} rs_table[LINK_QUAL_MAX_RETRY_NUM];
__le32 reserved2;
} __attribute__ ((packed));
/*
* REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
+ *
+ * 3945 and 4965 support hardware handshake with Bluetooth device on
+ * same platform. Bluetooth device alerts wireless device when it will Tx;
+ * wireless device can delay or kill its own Tx to accomodate.
*/
struct iwl4965_bt_cmd {
u8 flags;
*/
#define IWL_POWER_VEC_SIZE 5
-#define IWL_POWER_DRIVER_ALLOW_SLEEP_MSK __constant_cpu_to_le16(1<<0)
-#define IWL_POWER_SLEEP_OVER_DTIM_MSK __constant_cpu_to_le16(1<<2)
-#define IWL_POWER_PCI_PM_MSK __constant_cpu_to_le16(1<<3)
+#define IWL_POWER_DRIVER_ALLOW_SLEEP_MSK __constant_cpu_to_le16(1 << 0)
+#define IWL_POWER_SLEEP_OVER_DTIM_MSK __constant_cpu_to_le16(1 << 2)
+#define IWL_POWER_PCI_PM_MSK __constant_cpu_to_le16(1 << 3)
struct iwl4965_powertable_cmd {
__le16 flags;
*
*****************************************************************************/
+/**
+ * struct iwl4965_scan_channel - entry in REPLY_SCAN_CMD channel table
+ *
+ * One for each channel in the scan list.
+ * Each channel can independently select:
+ * 1) SSID for directed active scans
+ * 2) Txpower setting (for rate specified within Tx command)
+ * 3) How long to stay on-channel (behavior may be modified by quiet_time,
+ * quiet_plcp_th, good_CRC_th)
+ *
+ * To avoid uCode errors, make sure the following are true (see comments
+ * under struct iwl4965_scan_cmd about max_out_time and quiet_time):
+ * 1) If using passive_dwell (i.e. passive_dwell != 0):
+ * active_dwell <= passive_dwell (< max_out_time if max_out_time != 0)
+ * 2) quiet_time <= active_dwell
+ * 3) If restricting off-channel time (i.e. max_out_time !=0):
+ * passive_dwell < max_out_time
+ * active_dwell < max_out_time
+ */
struct iwl4965_scan_channel {
- /* type is defined as:
- * 0:0 active (0 - passive)
- * 1:4 SSID direct
- * If 1 is set then corresponding SSID IE is transmitted in probe
+ /*
+ * type is defined as:
+ * 0:0 1 = active, 0 = passive
+ * 1:4 SSID direct bit map; if a bit is set, then corresponding
+ * SSID IE is transmitted in probe request.
* 5:7 reserved
*/
u8 type;
- u8 channel;
+ u8 channel; /* band is selected by iwl4965_scan_cmd "flags" field */
struct iwl4965_tx_power tpc;
- __le16 active_dwell;
- __le16 passive_dwell;
+ __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
+ __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
} __attribute__ ((packed));
+/**
+ * struct iwl4965_ssid_ie - directed scan network information element
+ *
+ * Up to 4 of these may appear in REPLY_SCAN_CMD, selected by "type" field
+ * in struct iwl4965_scan_channel; each channel may select different ssids from
+ * among the 4 entries. SSID IEs get transmitted in reverse order of entry.
+ */
struct iwl4965_ssid_ie {
u8 id;
u8 len;
/*
* REPLY_SCAN_CMD = 0x80 (command)
+ *
+ * The hardware scan command is very powerful; the driver can set it up to
+ * maintain (relatively) normal network traffic while doing a scan in the
+ * background. The max_out_time and suspend_time control the ratio of how
+ * long the device stays on an associated network channel ("service channel")
+ * vs. how long it's away from the service channel, i.e. tuned to other channels
+ * for scanning.
+ *
+ * max_out_time is the max time off-channel (in usec), and suspend_time
+ * is how long (in "extended beacon" format) that the scan is "suspended"
+ * after returning to the service channel. That is, suspend_time is the
+ * time that we stay on the service channel, doing normal work, between
+ * scan segments. The driver may set these parameters differently to support
+ * scanning when associated vs. not associated, and light vs. heavy traffic
+ * loads when associated.
+ *
+ * After receiving this command, the device's scan engine does the following;
+ *
+ * 1) Sends SCAN_START notification to driver
+ * 2) Checks to see if it has time to do scan for one channel
+ * 3) Sends NULL packet, with power-save (PS) bit set to 1,
+ * to tell AP that we're going off-channel
+ * 4) Tunes to first channel in scan list, does active or passive scan
+ * 5) Sends SCAN_RESULT notification to driver
+ * 6) Checks to see if it has time to do scan on *next* channel in list
+ * 7) Repeats 4-6 until it no longer has time to scan the next channel
+ * before max_out_time expires
+ * 8) Returns to service channel
+ * 9) Sends NULL packet with PS=0 to tell AP that we're back
+ * 10) Stays on service channel until suspend_time expires
+ * 11) Repeats entire process 2-10 until list is complete
+ * 12) Sends SCAN_COMPLETE notification
+ *
+ * For fast, efficient scans, the scan command also has support for staying on
+ * a channel for just a short time, if doing active scanning and getting no
+ * responses to the transmitted probe request. This time is controlled by
+ * quiet_time, and the number of received packets below which a channel is
+ * considered "quiet" is controlled by quiet_plcp_threshold.
+ *
+ * For active scanning on channels that have regulatory restrictions against
+ * blindly transmitting, the scan can listen before transmitting, to make sure
+ * that there is already legitimate activity on the channel. If enough
+ * packets are cleanly received on the channel (controlled by good_CRC_th,
+ * typical value 1), the scan engine starts transmitting probe requests.
+ *
+ * Driver must use separate scan commands for 2.4 vs. 5 GHz bands.
+ *
+ * To avoid uCode errors, see timing restrictions described under
+ * struct iwl4965_scan_channel.
*/
struct iwl4965_scan_cmd {
__le16 len;
u8 reserved0;
- u8 channel_count;
- __le16 quiet_time; /* dwell only this long on quiet chnl
- * (active scan) */
- __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
- __le16 good_CRC_th; /* passive -> active promotion threshold */
- __le16 rx_chain;
- __le32 max_out_time; /* max usec to be out of associated (service)
- * chnl */
- __le32 suspend_time; /* pause scan this long when returning to svc
- * chnl.
- * 3945 -- 31:24 # beacons, 19:0 additional usec,
- * 4965 -- 31:22 # beacons, 21:0 additional usec.
- */
- __le32 flags;
- __le32 filter_flags;
-
+ u8 channel_count; /* # channels in channel list */
+ __le16 quiet_time; /* dwell only this # millisecs on quiet channel
+ * (only for active scan) */
+ __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
+ __le16 good_CRC_th; /* passive -> active promotion threshold */
+ __le16 rx_chain; /* RXON_RX_CHAIN_* */
+ __le32 max_out_time; /* max usec to be away from associated (service)
+ * channel */
+ __le32 suspend_time; /* pause scan this long (in "extended beacon
+ * format") when returning to service chnl:
+ * 3945; 31:24 # beacons, 19:0 additional usec,
+ * 4965; 31:22 # beacons, 21:0 additional usec.
+ */
+ __le32 flags; /* RXON_FLG_* */
+ __le32 filter_flags; /* RXON_FILTER_* */
+
+ /* For active scans (set to all-0s for passive scans).
+ * Does not include payload. Must specify Tx rate; no rate scaling. */
struct iwl4965_tx_cmd tx_cmd;
+
+ /* For directed active scans (set to all-0s otherwise) */
struct iwl4965_ssid_ie direct_scan[PROBE_OPTION_MAX];
- u8 data[0];
/*
- * The channels start after the probe request payload and are of type:
+ * Probe request frame, followed by channel list.
+ *
+ * Size of probe request frame is specified by byte count in tx_cmd.
+ * Channel list follows immediately after probe request frame.
+ * Number of channels in list is specified by channel_count.
+ * Each channel in list is of type:
*
* struct iwl4965_scan_channel channels[0];
*
* NOTE: Only one band of channels can be scanned per pass. You
- * can not mix 2.4GHz channels and 5.2GHz channels and must
- * request a scan multiple times (not concurrently)
- *
+ * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
+ * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
+ * before requesting another scan.
*/
+ u8 data[0];
} __attribute__ ((packed));
/* Can abort will notify by complete notification with abort status. */
__le32 interference_data_flag; /* flag for interference data
* availability. 1 when data is
* available. */
- __le32 channel_load; /* counts RX Enable time */
+ __le32 channel_load; /* counts RX Enable time in uSec */
__le32 dsp_false_alarms; /* DSP false alarm (both OFDM
* and CCK) counter */
__le32 beacon_rssi_a;