return NETDEV_TX_OK;
}
-/**
- * iwl_mac_config - mac80211 config callback
- *
- * We ignore conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME since it seems to
- * be set inappropriately and the driver currently sets the hardware up to
- * use it whenever needed.
- */
-static int iwl_mac_config(struct ieee80211_hw *hw, u32 changed)
-{
- struct iwl_priv *priv = hw->priv;
- const struct iwl_channel_info *ch_info;
- struct ieee80211_conf *conf = &hw->conf;
- unsigned long flags = 0;
- int ret = 0;
- u16 ch;
- int scan_active = 0;
-
- mutex_lock(&priv->mutex);
- IWL_DEBUG_MAC80211(priv, "enter to channel %d changed 0x%X\n",
- conf->channel->hw_value, changed);
-
- if (unlikely(!priv->cfg->mod_params->disable_hw_scan &&
- test_bit(STATUS_SCANNING, &priv->status))) {
- scan_active = 1;
- IWL_DEBUG_MAC80211(priv, "leave - scanning\n");
- }
-
-
- /* during scanning mac80211 will delay channel setting until
- * scan finish with changed = 0
- */
- if (!changed || (changed & IEEE80211_CONF_CHANGE_CHANNEL)) {
- if (scan_active)
- goto set_ch_out;
-
- ch = ieee80211_frequency_to_channel(conf->channel->center_freq);
- ch_info = iwl_get_channel_info(priv, conf->channel->band, ch);
- if (!is_channel_valid(ch_info)) {
- IWL_DEBUG_MAC80211(priv, "leave - invalid channel\n");
- ret = -EINVAL;
- goto set_ch_out;
- }
-
- if (priv->iw_mode == NL80211_IFTYPE_ADHOC &&
- !is_channel_ibss(ch_info)) {
- IWL_ERR(priv, "channel %d in band %d not "
- "IBSS channel\n",
- conf->channel->hw_value, conf->channel->band);
- ret = -EINVAL;
- goto set_ch_out;
- }
-
- priv->current_ht_config.is_ht = conf_is_ht(conf);
-
- spin_lock_irqsave(&priv->lock, flags);
-
-
- /* if we are switching from ht to 2.4 clear flags
- * from any ht related info since 2.4 does not
- * support ht */
- if ((le16_to_cpu(priv->staging_rxon.channel) != ch))
- priv->staging_rxon.flags = 0;
-
- iwl_set_rxon_channel(priv, conf->channel);
-
- iwl_set_flags_for_band(priv, conf->channel->band);
- spin_unlock_irqrestore(&priv->lock, flags);
- set_ch_out:
- /* The list of supported rates and rate mask can be different
- * for each band; since the band may have changed, reset
- * the rate mask to what mac80211 lists */
- iwl_set_rate(priv);
- }
-
- if (changed & IEEE80211_CONF_CHANGE_PS) {
- if (conf->flags & IEEE80211_CONF_PS)
- ret = iwl_power_set_user_mode(priv, IWL_POWER_INDEX_3);
- else
- ret = iwl_power_set_user_mode(priv, IWL_POWER_MODE_CAM);
- if (ret)
- IWL_DEBUG_MAC80211(priv, "Error setting power level\n");
-
- }
-
- if (changed & IEEE80211_CONF_CHANGE_POWER) {
- IWL_DEBUG_MAC80211(priv, "TX Power old=%d new=%d\n",
- priv->tx_power_user_lmt, conf->power_level);
-
- iwl_set_tx_power(priv, conf->power_level, false);
- }
-
- /* call to ensure that 4965 rx_chain is set properly in monitor mode */
- if (priv->cfg->ops->hcmd->set_rxon_chain)
- priv->cfg->ops->hcmd->set_rxon_chain(priv);
-
- if (changed & IEEE80211_CONF_CHANGE_RADIO_ENABLED) {
- if (conf->radio_enabled &&
- iwl_radio_kill_sw_enable_radio(priv)) {
- IWL_DEBUG_MAC80211(priv, "leave - RF-KILL - "
- "waiting for uCode\n");
- goto out;
- }
-
- if (!conf->radio_enabled)
- iwl_radio_kill_sw_disable_radio(priv);
- }
-
- if (!conf->radio_enabled) {
- IWL_DEBUG_MAC80211(priv, "leave - radio disabled\n");
- goto out;
- }
-
- if (!iwl_is_ready(priv)) {
- IWL_DEBUG_MAC80211(priv, "leave - not ready\n");
- goto out;
- }
-
- if (scan_active)
- goto out;
-
- if (memcmp(&priv->active_rxon,
- &priv->staging_rxon, sizeof(priv->staging_rxon)))
- iwlcore_commit_rxon(priv);
- else
- IWL_DEBUG_INFO(priv, "No re-sending same RXON configuration.\n");
-
-
-out:
- IWL_DEBUG_MAC80211(priv, "leave\n");
- mutex_unlock(&priv->mutex);
- return ret;
-}
-
static void iwl_config_ap(struct iwl_priv *priv)
{
int ret = 0;