REPLY_BT_COEX_PROFILE_NOTIF = 0xce,
REPLY_BT_COEX_SCO = 0xcf,
+ /* PAN commands */
+ REPLY_WIPAN_PARAMS = 0xb2,
+ REPLY_WIPAN_RXON = 0xb3, /* use REPLY_RXON structure */
+ REPLY_WIPAN_RXON_TIMING = 0xb4, /* use REPLY_RXON_TIMING structure */
+ REPLY_WIPAN_RXON_ASSOC = 0xb6, /* use REPLY_RXON_ASSOC structure */
+ REPLY_WIPAN_QOS_PARAM = 0xb7, /* use REPLY_QOS_PARAM structure */
+ REPLY_WIPAN_WEPKEY = 0xb8, /* use REPLY_WEPKEY structure */
+ REPLY_WIPAN_P2P_CHANNEL_SWITCH = 0xb9,
+ REPLY_WIPAN_NOA_NOTIFICATION = 0xbc,
+
REPLY_MAX = 0xff
};
/**
* Command REPLY_TX_POWER_DBM_CMD = 0x98
- * struct iwl5000_tx_power_dbm_cmd
+ * struct iwlagn_tx_power_dbm_cmd
*/
-#define IWL50_TX_POWER_AUTO 0x7f
-#define IWL50_TX_POWER_NO_CLOSED (0x1 << 6)
+#define IWLAGN_TX_POWER_AUTO 0x7f
+#define IWLAGN_TX_POWER_NO_CLOSED (0x1 << 6)
-struct iwl5000_tx_power_dbm_cmd {
+struct iwlagn_tx_power_dbm_cmd {
s8 global_lmt; /*in half-dBm (e.g. 30 = 15 dBm) */
u8 flags;
s8 srv_chan_lmt; /*in half-dBm (e.g. 30 = 15 dBm) */
RXON_DEV_TYPE_ESS = 3,
RXON_DEV_TYPE_IBSS = 4,
RXON_DEV_TYPE_SNIFFER = 6,
+ RXON_DEV_TYPE_CP = 7,
+ RXON_DEV_TYPE_2STA = 8,
+ RXON_DEV_TYPE_P2P = 9,
};
__le16 atim_window;
__le32 beacon_init_val;
__le16 listen_interval;
- __le16 reserved;
+ u8 dtim_period;
+ u8 delta_cp_bss_tbtts;
} __packed;
/*
/* Special, dedicated locations within device's station table */
#define IWL_AP_ID 0
+#define IWL_AP_ID_PAN 1
#define IWL_STA_ID 2
#define IWL3945_BROADCAST_ID 24
#define IWL3945_STATION_COUNT 25
#define IWL4965_BROADCAST_ID 31
#define IWL4965_STATION_COUNT 32
+#define IWLAGN_PAN_BCAST_ID 14
#define IWLAGN_BROADCAST_ID 15
#define IWLAGN_STATION_COUNT 16
#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2)
#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8)
+#define STA_FLG_PAN_STATION cpu_to_le32(1 << 13)
#define STA_FLG_RTS_MIMO_PROT_MSK cpu_to_le32(1 << 17)
#define STA_FLG_AGG_MPDU_8US_MSK cpu_to_le32(1 << 18)
#define STA_FLG_MAX_AGG_SIZE_POS (19)
#define STA_KEY_FLG_KEY_SIZE_MSK cpu_to_le16(0x1000)
#define STA_KEY_MULTICAST_MSK cpu_to_le16(0x4000)
#define STA_KEY_MAX_NUM 8
+#define STA_KEY_MAX_NUM_PAN 16
/* Flags indicate whether to modify vs. don't change various station params */
#define STA_MODIFY_KEY_MASK 0x01
u8 key[16]; /* 16-byte unicast decryption key */
} __packed;
-/* 5000 */
+/* agn */
struct iwl_keyinfo {
__le16 key_flags;
u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
__le16 reserved2;
} __packed;
-/* 5000 */
+/* agn */
struct iwl_addsta_cmd {
u8 mode; /* 1: modify existing, 0: add new station */
u8 reserved[3];
TX_STATUS_FAIL_TID_DISABLE = 0x8d,
TX_STATUS_FAIL_FIFO_FLUSHED = 0x8e,
TX_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
- /* uCode drop due to FW drop request */
- TX_STATUS_FAIL_FW_DROP = 0x90,
- /*
- * uCode drop due to station color mismatch
- * between tx command and station table
- */
- TX_STATUS_FAIL_STA_COLOR_MISMATCH_DROP = 0x91,
+ TX_STATUS_FAIL_PASSIVE_NO_RX = 0x90,
+ TX_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
};
#define TX_PACKET_MODE_REGULAR 0x0000
AGG_TX_STATE_DELAY_TX_MSK = 0x400
};
+#define AGG_TX_STATUS_MSK 0x00000fff /* bits 0:11 */
+#define AGG_TX_TRY_MSK 0x0000f000 /* bits 12:15 */
+
#define AGG_TX_STATE_LAST_SENT_MSK (AGG_TX_STATE_LAST_SENT_TTL_MSK | \
AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK | \
AGG_TX_STATE_LAST_SENT_BT_KILL_MSK)
#define IWL50_TX_RES_INV_RATE_INDEX_MSK 0x80
/* refer to ra_tid */
-#define IWL50_TX_RES_TID_POS 0
-#define IWL50_TX_RES_TID_MSK 0x0f
-#define IWL50_TX_RES_RA_POS 4
-#define IWL50_TX_RES_RA_MSK 0xf0
+#define IWLAGN_TX_RES_TID_POS 0
+#define IWLAGN_TX_RES_TID_MSK 0x0f
+#define IWLAGN_TX_RES_RA_POS 4
+#define IWLAGN_TX_RES_RA_MSK 0xf0
-struct iwl5000_tx_resp {
+struct iwlagn_tx_resp {
u8 frame_count; /* 1 no aggregation, >1 aggregation */
u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
u8 failure_rts; /* # failures due to unsuccessful RTS */
#define BT_MAX_KILL_DEF (0x5)
#define BT_MAX_KILL_MAX (0xFF)
+#define BT_DURATION_LIMIT_DEF 625
+#define BT_DURATION_LIMIT_MAX 1250
+#define BT_DURATION_LIMIT_MIN 625
+
+#define BT_ON_THRESHOLD_DEF 4
+#define BT_ON_THRESHOLD_MAX 1000
+#define BT_ON_THRESHOLD_MIN 1
+
+#define BT_FRAG_THRESHOLD_DEF 0
+#define BT_FRAG_THRESHOLD_MAX 0
+#define BT_FRAG_THRESHOLD_MIN 0
+
+#define BT_AGG_THRESHOLD_DEF 0
+#define BT_AGG_THRESHOLD_MAX 0
+#define BT_AGG_THRESHOLD_MIN 0
+
/*
* REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
*
__le32 kill_cts_mask;
} __packed;
-#define IWL6000G2B_BT_FLAG_CHANNEL_INHIBITION BIT(0)
+#define IWLAGN_BT_FLAG_CHANNEL_INHIBITION BIT(0)
-#define IWL6000G2B_BT_FLAG_COEX_MODE_MASK (BIT(3)|BIT(4)|BIT(5))
-#define IWL6000G2B_BT_FLAG_COEX_MODE_SHIFT 3
-#define IWL6000G2B_BT_FLAG_COEX_MODE_DISABLED 0
-#define IWL6000G2B_BT_FLAG_COEX_MODE_LEGACY_2W 1
-#define IWL6000G2B_BT_FLAG_COEX_MODE_3W 2
-#define IWL6000G2B_BT_FLAG_COEX_MODE_4W 3
+#define IWLAGN_BT_FLAG_COEX_MODE_MASK (BIT(3)|BIT(4)|BIT(5))
+#define IWLAGN_BT_FLAG_COEX_MODE_SHIFT 3
+#define IWLAGN_BT_FLAG_COEX_MODE_DISABLED 0
+#define IWLAGN_BT_FLAG_COEX_MODE_LEGACY_2W 1
+#define IWLAGN_BT_FLAG_COEX_MODE_3W 2
+#define IWLAGN_BT_FLAG_COEX_MODE_4W 3
-#define IWL6000G2B_BT_FLAG_UCODE_DEFAULT BIT(6)
-#define IWL6000G2B_BT_FLAG_NOCOEX_NOTIF BIT(7)
+#define IWLAGN_BT_FLAG_UCODE_DEFAULT BIT(6)
+#define IWLAGN_BT_FLAG_NOCOEX_NOTIF BIT(7)
-#define IWL6000G2B_BT_PRIO_BOOST_MAX 0xFF
-#define IWL6000G2B_BT_PRIO_BOOST_MIN 0x00
-#define IWL6000G2B_BT_PRIO_BOOST_DEFAULT 0x00
+#define IWLAGN_BT_PRIO_BOOST_MAX 0xFF
+#define IWLAGN_BT_PRIO_BOOST_MIN 0x00
+#define IWLAGN_BT_PRIO_BOOST_DEFAULT 0xF0
-#define IWL6000G2B_BT_MAX_KILL_DEFAULT 5
+#define IWLAGN_BT_MAX_KILL_DEFAULT 5
-#define IWL6000G2B_BT3_T7_DEFAULT 1
+#define IWLAGN_BT3_T7_DEFAULT 1
-#define IWL6000G2B_BT_KILL_ACK_MASK_DEFAULT cpu_to_le32(0xffffffff)
-#define IWL6000G2B_BT_KILL_CTS_MASK_DEFAULT cpu_to_le32(0xffffffff)
+#define IWLAGN_BT_KILL_ACK_MASK_DEFAULT cpu_to_le32(0xffffffff)
+#define IWLAGN_BT_KILL_CTS_MASK_DEFAULT cpu_to_le32(0xffffffff)
-#define IWL6000G2B_BT3_PRIO_SAMPLE_DEFAULT 2
+#define IWLAGN_BT3_PRIO_SAMPLE_DEFAULT 2
-#define IWL6000G2B_BT3_T2_DEFAULT 0xc
+#define IWLAGN_BT3_T2_DEFAULT 0xc
-#define IWL6000G2B_BT_VALID_ENABLE_FLAGS cpu_to_le16(BIT(0))
-#define IWL6000G2B_BT_VALID_BOOST cpu_to_le16(BIT(1))
-#define IWL6000G2B_BT_VALID_MAX_KILL cpu_to_le16(BIT(2))
-#define IWL6000G2B_BT_VALID_3W_TIMERS cpu_to_le16(BIT(3))
-#define IWL6000G2B_BT_VALID_KILL_ACK_MASK cpu_to_le16(BIT(4))
-#define IWL6000G2B_BT_VALID_KILL_CTS_MASK cpu_to_le16(BIT(5))
-#define IWL6000G2B_BT_VALID_BT4_TIMES cpu_to_le16(BIT(6))
-#define IWL6000G2B_BT_VALID_3W_LUT cpu_to_le16(BIT(7))
+#define IWLAGN_BT_VALID_ENABLE_FLAGS cpu_to_le16(BIT(0))
+#define IWLAGN_BT_VALID_BOOST cpu_to_le16(BIT(1))
+#define IWLAGN_BT_VALID_MAX_KILL cpu_to_le16(BIT(2))
+#define IWLAGN_BT_VALID_3W_TIMERS cpu_to_le16(BIT(3))
+#define IWLAGN_BT_VALID_KILL_ACK_MASK cpu_to_le16(BIT(4))
+#define IWLAGN_BT_VALID_KILL_CTS_MASK cpu_to_le16(BIT(5))
+#define IWLAGN_BT_VALID_BT4_TIMES cpu_to_le16(BIT(6))
+#define IWLAGN_BT_VALID_3W_LUT cpu_to_le16(BIT(7))
-#define IWL6000G2B_BT_ALL_VALID_MSK (IWL6000G2B_BT_VALID_ENABLE_FLAGS | \
- IWL6000G2B_BT_VALID_BOOST | \
- IWL6000G2B_BT_VALID_MAX_KILL | \
- IWL6000G2B_BT_VALID_3W_TIMERS | \
- IWL6000G2B_BT_VALID_KILL_ACK_MASK | \
- IWL6000G2B_BT_VALID_KILL_CTS_MASK | \
- IWL6000G2B_BT_VALID_BT4_TIMES | \
- IWL6000G2B_BT_VALID_3W_LUT)
+#define IWLAGN_BT_ALL_VALID_MSK (IWLAGN_BT_VALID_ENABLE_FLAGS | \
+ IWLAGN_BT_VALID_BOOST | \
+ IWLAGN_BT_VALID_MAX_KILL | \
+ IWLAGN_BT_VALID_3W_TIMERS | \
+ IWLAGN_BT_VALID_KILL_ACK_MASK | \
+ IWLAGN_BT_VALID_KILL_CTS_MASK | \
+ IWLAGN_BT_VALID_BT4_TIMES | \
+ IWLAGN_BT_VALID_3W_LUT)
-struct iwl6000g2b_bt_cmd {
+struct iwlagn_bt_cmd {
u8 flags;
u8 ledtime; /* unused */
u8 max_kill;
__le16 bt4_decision_time; /* unused */
__le16 valid;
u8 prio_boost;
- u8 reserved[3];
+ /*
+ * set IWLAGN_BT_VALID_BOOST to "1" in "valid" bitmask
+ * if configure the following patterns
+ */
+ u8 tx_prio_boost; /* SW boost of WiFi tx priority */
+ __le16 rx_prio_boost; /* SW boost of WiFi rx priority */
};
-#define IWL6000G2B_BT_SCO_ACTIVE cpu_to_le32(BIT(0))
+#define IWLAGN_BT_SCO_ACTIVE cpu_to_le32(BIT(0))
-struct iwl6000g2b_bt_sco_cmd {
+struct iwlagn_bt_sco_cmd {
__le32 flags;
};
struct iwl_scancomplete_notification {
u8 scanned_channels;
u8 status;
- u8 reserved;
+ u8 bt_status; /* BT On/Off status */
u8 last_channel;
__le32 tsf_low;
__le32 tsf_high;
*/
/* Phy calibration command for series */
-
+/* The default calibrate table size if not specified by firmware */
+#define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE 18
enum {
IWL_PHY_CALIBRATE_DIFF_GAIN_CMD = 7,
IWL_PHY_CALIBRATE_DC_CMD = 8,
#define IWL_CALIB_INIT_CFG_ALL cpu_to_le32(0xffffffff)
+/* This enum defines the bitmap of various calibrations to enable in both
+ * init ucode and runtime ucode through CALIBRATION_CFG_CMD.
+ */
+enum iwl_ucode_calib_cfg {
+ IWL_CALIB_CFG_RX_BB_IDX,
+ IWL_CALIB_CFG_DC_IDX,
+ IWL_CALIB_CFG_TX_IQ_IDX,
+ IWL_CALIB_CFG_RX_IQ_IDX,
+ IWL_CALIB_CFG_NOISE_IDX,
+ IWL_CALIB_CFG_CRYSTAL_IDX,
+ IWL_CALIB_CFG_TEMPERATURE_IDX,
+ IWL_CALIB_CFG_PAPD_IDX,
+};
+
+
struct iwl_calib_cfg_elmnt_s {
__le32 is_enable;
__le32 start;
/*
* BT Status notification
- * REPLY_BT_COEX_PROFILE_NOTIF = 0xcb
+ * REPLY_BT_COEX_PROFILE_NOTIF = 0xce
*/
enum iwl_bt_coex_profile_traffic_load {
IWL_BT_COEX_TRAFFIC_LOAD_NONE = 0,
*/
};
+#define BT_UART_MSG_FRAME1MSGTYPE_POS (0)
+#define BT_UART_MSG_FRAME1MSGTYPE_MSK \
+ (0x7 << BT_UART_MSG_FRAME1MSGTYPE_POS)
+#define BT_UART_MSG_FRAME1SSN_POS (3)
+#define BT_UART_MSG_FRAME1SSN_MSK \
+ (0x3 << BT_UART_MSG_FRAME1SSN_POS)
+#define BT_UART_MSG_FRAME1UPDATEREQ_POS (5)
+#define BT_UART_MSG_FRAME1UPDATEREQ_MSK \
+ (0x1 << BT_UART_MSG_FRAME1UPDATEREQ_POS)
+#define BT_UART_MSG_FRAME1RESERVED_POS (6)
+#define BT_UART_MSG_FRAME1RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME1RESERVED_POS)
+
+#define BT_UART_MSG_FRAME2OPENCONNECTIONS_POS (0)
+#define BT_UART_MSG_FRAME2OPENCONNECTIONS_MSK \
+ (0x3 << BT_UART_MSG_FRAME2OPENCONNECTIONS_POS)
+#define BT_UART_MSG_FRAME2TRAFFICLOAD_POS (2)
+#define BT_UART_MSG_FRAME2TRAFFICLOAD_MSK \
+ (0x3 << BT_UART_MSG_FRAME2TRAFFICLOAD_POS)
+#define BT_UART_MSG_FRAME2CHLSEQN_POS (4)
+#define BT_UART_MSG_FRAME2CHLSEQN_MSK \
+ (0x1 << BT_UART_MSG_FRAME2CHLSEQN_POS)
+#define BT_UART_MSG_FRAME2INBAND_POS (5)
+#define BT_UART_MSG_FRAME2INBAND_MSK \
+ (0x1 << BT_UART_MSG_FRAME2INBAND_POS)
+#define BT_UART_MSG_FRAME2RESERVED_POS (6)
+#define BT_UART_MSG_FRAME2RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME2RESERVED_POS)
+
+#define BT_UART_MSG_FRAME3SCOESCO_POS (0)
+#define BT_UART_MSG_FRAME3SCOESCO_MSK \
+ (0x1 << BT_UART_MSG_FRAME3SCOESCO_POS)
+#define BT_UART_MSG_FRAME3SNIFF_POS (1)
+#define BT_UART_MSG_FRAME3SNIFF_MSK \
+ (0x1 << BT_UART_MSG_FRAME3SNIFF_POS)
+#define BT_UART_MSG_FRAME3A2DP_POS (2)
+#define BT_UART_MSG_FRAME3A2DP_MSK \
+ (0x1 << BT_UART_MSG_FRAME3A2DP_POS)
+#define BT_UART_MSG_FRAME3ACL_POS (3)
+#define BT_UART_MSG_FRAME3ACL_MSK \
+ (0x1 << BT_UART_MSG_FRAME3ACL_POS)
+#define BT_UART_MSG_FRAME3MASTER_POS (4)
+#define BT_UART_MSG_FRAME3MASTER_MSK \
+ (0x1 << BT_UART_MSG_FRAME3MASTER_POS)
+#define BT_UART_MSG_FRAME3OBEX_POS (5)
+#define BT_UART_MSG_FRAME3OBEX_MSK \
+ (0x1 << BT_UART_MSG_FRAME3OBEX_POS)
+#define BT_UART_MSG_FRAME3RESERVED_POS (6)
+#define BT_UART_MSG_FRAME3RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME3RESERVED_POS)
+
+#define BT_UART_MSG_FRAME4IDLEDURATION_POS (0)
+#define BT_UART_MSG_FRAME4IDLEDURATION_MSK \
+ (0x3F << BT_UART_MSG_FRAME4IDLEDURATION_POS)
+#define BT_UART_MSG_FRAME4RESERVED_POS (6)
+#define BT_UART_MSG_FRAME4RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME4RESERVED_POS)
+
+#define BT_UART_MSG_FRAME5TXACTIVITY_POS (0)
+#define BT_UART_MSG_FRAME5TXACTIVITY_MSK \
+ (0x3 << BT_UART_MSG_FRAME5TXACTIVITY_POS)
+#define BT_UART_MSG_FRAME5RXACTIVITY_POS (2)
+#define BT_UART_MSG_FRAME5RXACTIVITY_MSK \
+ (0x3 << BT_UART_MSG_FRAME5RXACTIVITY_POS)
+#define BT_UART_MSG_FRAME5ESCORETRANSMIT_POS (4)
+#define BT_UART_MSG_FRAME5ESCORETRANSMIT_MSK \
+ (0x3 << BT_UART_MSG_FRAME5ESCORETRANSMIT_POS)
+#define BT_UART_MSG_FRAME5RESERVED_POS (6)
+#define BT_UART_MSG_FRAME5RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME5RESERVED_POS)
+
+#define BT_UART_MSG_FRAME6SNIFFINTERVAL_POS (0)
+#define BT_UART_MSG_FRAME6SNIFFINTERVAL_MSK \
+ (0x1F << BT_UART_MSG_FRAME6SNIFFINTERVAL_POS)
+#define BT_UART_MSG_FRAME6DISCOVERABLE_POS (5)
+#define BT_UART_MSG_FRAME6DISCOVERABLE_MSK \
+ (0x1 << BT_UART_MSG_FRAME6DISCOVERABLE_POS)
+#define BT_UART_MSG_FRAME6RESERVED_POS (6)
+#define BT_UART_MSG_FRAME6RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME6RESERVED_POS)
+
+#define BT_UART_MSG_FRAME7SNIFFACTIVITY_POS (0)
+#define BT_UART_MSG_FRAME7SNIFFACTIVITY_MSK \
+ (0x7 << BT_UART_MSG_FRAME7SNIFFACTIVITY_POS)
+#define BT_UART_MSG_FRAME7INQUIRYPAGESRMODE_POS (3)
+#define BT_UART_MSG_FRAME7INQUIRYPAGESRMODE_MSK \
+ (0x3 << BT_UART_MSG_FRAME7INQUIRYPAGESRMODE_POS)
+#define BT_UART_MSG_FRAME7CONNECTABLE_POS (5)
+#define BT_UART_MSG_FRAME7CONNECTABLE_MSK \
+ (0x1 << BT_UART_MSG_FRAME7CONNECTABLE_POS)
+#define BT_UART_MSG_FRAME7RESERVED_POS (6)
+#define BT_UART_MSG_FRAME7RESERVED_MSK \
+ (0x3 << BT_UART_MSG_FRAME7RESERVED_POS)
+
+
+struct iwl_bt_uart_msg {
+ u8 header;
+ u8 frame1;
+ u8 frame2;
+ u8 frame3;
+ u8 frame4;
+ u8 frame5;
+ u8 frame6;
+ u8 frame7;
+} __attribute__((packed));
+
struct iwl_bt_coex_profile_notif {
- u8 uart_msg[8];
+ struct iwl_bt_uart_msg last_bt_uart_msg;
u8 bt_status; /* 0 - off, 1 - on */
u8 bt_traffic_load; /* 0 .. 3? */
u8 bt_ci_compliance; /* 0 - not complied, 1 - complied */
int iwl_agn_check_rxon_cmd(struct iwl_priv *priv);
+/*
+ * REPLY_WIPAN_PARAMS = 0xb2 (Commands and Notification)
+ */
+
+/**
+ * struct iwl_wipan_slot
+ * @width: Time in TU
+ * @type:
+ * 0 - BSS
+ * 1 - PAN
+ */
+struct iwl_wipan_slot {
+ __le16 width;
+ u8 type;
+ u8 reserved;
+} __packed;
+
+#define IWL_WIPAN_PARAMS_FLG_LEAVE_CHANNEL_CTS BIT(1) /* reserved */
+#define IWL_WIPAN_PARAMS_FLG_LEAVE_CHANNEL_QUIET BIT(2) /* reserved */
+#define IWL_WIPAN_PARAMS_FLG_SLOTTED_MODE BIT(3) /* reserved */
+#define IWL_WIPAN_PARAMS_FLG_FILTER_BEACON_NOTIF BIT(4)
+#define IWL_WIPAN_PARAMS_FLG_FULL_SLOTTED_MODE BIT(5)
+
+/**
+ * struct iwl_wipan_params_cmd
+ * @flags:
+ * bit0: reserved
+ * bit1: CP leave channel with CTS
+ * bit2: CP leave channel qith Quiet
+ * bit3: slotted mode
+ * 1 - work in slotted mode
+ * 0 - work in non slotted mode
+ * bit4: filter beacon notification
+ * bit5: full tx slotted mode. if this flag is set,
+ * uCode will perform leaving channel methods in context switch
+ * also when working in same channel mode
+ * @num_slots: 1 - 10
+ */
+struct iwl_wipan_params_cmd {
+ __le16 flags;
+ u8 reserved;
+ u8 num_slots;
+ struct iwl_wipan_slot slots[10];
+} __packed;
+
+/*
+ * REPLY_WIPAN_P2P_CHANNEL_SWITCH = 0xb9
+ *
+ * TODO: Figure out what this is used for,
+ * it can only switch between 2.4 GHz
+ * channels!!
+ */
+
+struct iwl_wipan_p2p_channel_switch_cmd {
+ __le16 channel;
+ __le16 reserved;
+};
+
+/*
+ * REPLY_WIPAN_NOA_NOTIFICATION = 0xbc
+ *
+ * This is used by the device to notify us of the
+ * NoA schedule it determined so we can forward it
+ * to userspace for inclusion in probe responses.
+ *
+ * In beacons, the NoA schedule is simply appended
+ * to the frame we give the device.
+ */
+
+struct iwl_wipan_noa_descriptor {
+ u8 count;
+ __le32 duration;
+ __le32 interval;
+ __le32 starttime;
+} __packed;
+
+struct iwl_wipan_noa_attribute {
+ u8 id;
+ __le16 length;
+ u8 index;
+ u8 ct_window;
+ struct iwl_wipan_noa_descriptor descr0, descr1;
+ u8 reserved;
+} __packed;
+
+struct iwl_wipan_noa_notification {
+ u32 noa_active;
+ struct iwl_wipan_noa_attribute noa_attribute;
+} __packed;
+
#endif /* __iwl_commands_h__ */
projects / karo-tx-linux.git / blobdiff