#include <linux/suspend.h>
#include <linux/delay.h>
#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/of.h>
#include <linux/regmap.h>
#include <linux/regulator/of_regulator.h>
*/
struct regulator_enable_gpio {
struct list_head list;
- int gpio;
+ struct gpio_desc *gpiod;
u32 enable_count; /* a number of enabled shared GPIO */
u32 request_count; /* a number of requested shared GPIO */
unsigned int ena_gpio_invert:1;
const struct regulator_config *config)
{
struct regulator_enable_gpio *pin;
+ struct gpio_desc *gpiod;
int ret;
+ gpiod = gpio_to_desc(config->ena_gpio);
+
list_for_each_entry(pin, ®ulator_ena_gpio_list, list) {
- if (pin->gpio == config->ena_gpio) {
+ if (pin->gpiod == gpiod) {
rdev_dbg(rdev, "GPIO %d is already used\n",
config->ena_gpio);
goto update_ena_gpio_to_rdev;
return -ENOMEM;
}
- pin->gpio = config->ena_gpio;
+ pin->gpiod = gpiod;
pin->ena_gpio_invert = config->ena_gpio_invert;
list_add(&pin->list, ®ulator_ena_gpio_list);
/* Free the GPIO only in case of no use */
list_for_each_entry_safe(pin, n, ®ulator_ena_gpio_list, list) {
- if (pin->gpio == rdev->ena_pin->gpio) {
+ if (pin->gpiod == rdev->ena_pin->gpiod) {
if (pin->request_count <= 1) {
pin->request_count = 0;
- gpio_free(pin->gpio);
+ gpiod_put(pin->gpiod);
list_del(&pin->list);
kfree(pin);
} else {
if (enable) {
/* Enable GPIO at initial use */
if (pin->enable_count == 0)
- gpio_set_value_cansleep(pin->gpio,
- !pin->ena_gpio_invert);
+ gpiod_set_value_cansleep(pin->gpiod,
+ !pin->ena_gpio_invert);
pin->enable_count++;
} else {
/* Disable GPIO if not used */
if (pin->enable_count <= 1) {
- gpio_set_value_cansleep(pin->gpio,
- pin->ena_gpio_invert);
+ gpiod_set_value_cansleep(pin->gpiod,
+ pin->ena_gpio_invert);
pin->enable_count = 0;
}
}
}
EXPORT_SYMBOL_GPL(regulator_list_voltage);
+/**
+ * regulator_get_regmap - get the regulator's register map
+ * @regulator: regulator source
+ *
+ * Returns the register map for the given regulator, or an ERR_PTR value
+ * if the regulator doesn't use regmap.
+ */
+struct regmap *regulator_get_regmap(struct regulator *regulator)
+{
+ struct regmap *map = regulator->rdev->regmap;
+
+ return map ? map : ERR_PTR(-EOPNOTSUPP);
+}
+
+/**
+ * regulator_get_hardware_vsel_register - get the HW voltage selector register
+ * @regulator: regulator source
+ * @vsel_reg: voltage selector register, output parameter
+ * @vsel_mask: mask for voltage selector bitfield, output parameter
+ *
+ * Returns the hardware register offset and bitmask used for setting the
+ * regulator voltage. This might be useful when configuring voltage-scaling
+ * hardware or firmware that can make I2C requests behind the kernel's back,
+ * for example.
+ *
+ * On success, the output parameters @vsel_reg and @vsel_mask are filled in
+ * and 0 is returned, otherwise a negative errno is returned.
+ */
+int regulator_get_hardware_vsel_register(struct regulator *regulator,
+ unsigned *vsel_reg,
+ unsigned *vsel_mask)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ struct regulator_ops *ops = rdev->desc->ops;
+
+ if (ops->set_voltage_sel != regulator_set_voltage_sel_regmap)
+ return -EOPNOTSUPP;
+
+ *vsel_reg = rdev->desc->vsel_reg;
+ *vsel_mask = rdev->desc->vsel_mask;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(regulator_get_hardware_vsel_register);
+
+/**
+ * regulator_list_hardware_vsel - get the HW-specific register value for a selector
+ * @regulator: regulator source
+ * @selector: identify voltage to list
+ *
+ * Converts the selector to a hardware-specific voltage selector that can be
+ * directly written to the regulator registers. The address of the voltage
+ * register can be determined by calling @regulator_get_hardware_vsel_register.
+ *
+ * On error a negative errno is returned.
+ */
+int regulator_list_hardware_vsel(struct regulator *regulator,
+ unsigned selector)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+ struct regulator_ops *ops = rdev->desc->ops;
+
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+ if (ops->set_voltage_sel != regulator_set_voltage_sel_regmap)
+ return -EOPNOTSUPP;
+
+ return selector;
+}
+EXPORT_SYMBOL_GPL(regulator_list_hardware_vsel);
+
/**
* regulator_get_linear_step - return the voltage step size between VSEL values
* @regulator: regulator source