#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/serial_core.h>
+#include <linux/dma-mapping.h>
#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
#include <asm/gpio.h>
#include <mach/bfin_serial_5xx.h>
-#ifdef CONFIG_SERIAL_BFIN_DMA
-#include <linux/dma-mapping.h>
+#include <asm/dma.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/cacheflush.h>
-#endif
#ifdef CONFIG_SERIAL_BFIN_MODULE
# undef CONFIG_EARLY_PRINTK
UART_PUT_CHAR(uart, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
uart->port.icount.tx++;
- SSYNC();
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
# ifdef CONFIG_BF54x
{
+ /*
+ * UART2 and UART3 on BF548 share interrupt PINs and DMA
+ * controllers with SPORT2 and SPORT3. UART rx and tx
+ * interrupts are generated in PIO mode only when configure
+ * their peripheral mapping registers properly, which means
+ * request corresponding DMA channels in PIO mode as well.
+ */
unsigned uart_dma_ch_rx, uart_dma_ch_tx;
switch (uart->port.irq) {
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
uart->cts_pin = -1;
- pr_info("Unable to attach BlackFin UART CTS interrupt.\
- So, disable it.\n");
+ pr_info("Unable to attach BlackFin UART CTS interrupt. So, disable it.\n");
}
}
if (uart->rts_pin >= 0) {
if (request_irq(uart->status_irq,
bfin_serial_mctrl_cts_int,
IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
- pr_info("Unable to attach BlackFin UART Modem \
- Status interrupt.\n");
+ pr_info("Unable to attach BlackFin UART Modem Status interrupt.\n");
}
/* CTS RTS PINs are negative assertive. */
if (termios->c_cflag & CMSPAR)
lcr |= STP;
+ spin_lock_irqsave(&uart->port.lock, flags);
+
port->read_status_mask = OE;
if (termios->c_iflag & INPCK)
port->read_status_mask |= (FE | PE);
if (termios->c_line != N_IRDA)
quot -= ANOMALY_05000230;
- spin_lock_irqsave(&uart->port.lock, flags);
-
UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
/* Disable UART */
* Enable the IrDA function if tty->ldisc.num is N_IRDA.
* In other cases, disable IrDA function.
*/
-static void bfin_serial_set_ldisc(struct uart_port *port)
+static void bfin_serial_set_ldisc(struct uart_port *port, int ld)
{
int line = port->line;
unsigned short val;
- if (line >= port->state->port.tty->driver->num)
- return;
-
- switch (port->state->port.tty->termios->c_line) {
+ switch (ld) {
case N_IRDA:
val = UART_GET_GCTL(&bfin_serial_ports[line]);
val |= (IREN | RPOLC);
struct bfin_serial_port *uart;
struct ktermios t;
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+ /*
+ * If we are using early serial, don't let the normal console rewind
+ * log buffer, since that causes things to be printed multiple times
+ */
+ bfin_serial_console.flags &= ~CON_PRINTBUFFER;
+#endif
+
if (port == -1 || port >= nr_active_ports)
port = 0;
bfin_serial_init_ports();