#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#endif
-static struct ehci_ctrl {
- struct ehci_hccr *hccr; /* R/O registers, not need for volatile */
- struct ehci_hcor *hcor;
- int rootdev;
- uint16_t portreset;
- struct QH qh_list __aligned(USB_DMA_MINALIGN);
- struct QH periodic_queue __aligned(USB_DMA_MINALIGN);
- uint32_t *periodic_list;
- int ntds;
-} ehcic[CONFIG_USB_MAX_CONTROLLER_COUNT];
+/*
+ * EHCI spec page 20 says that the HC may take up to 16 uFrames (= 4ms) to halt.
+ * Let's time out after 8 to have a little safety margin on top of that.
+ */
+#define HCHALT_TIMEOUT (8 * 1000)
+
+static struct ehci_ctrl ehcic[CONFIG_USB_MAX_CONTROLLER_COUNT];
#define ALIGN_END_ADDR(type, ptr, size) \
((uint32_t)(ptr) + roundup((size) * sizeof(type), USB_DMA_MINALIGN))
#define ehci_is_TDI() (0)
#endif
-int __ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg)
+__weak int ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg)
{
return PORTSC_PSPD(reg);
}
-int ehci_get_port_speed(struct ehci_hcor *hcor, uint32_t reg)
- __attribute__((weak, alias("__ehci_get_port_speed")));
-
-void __ehci_set_usbmode(int index)
+__weak void ehci_set_usbmode(int index)
{
uint32_t tmp;
uint32_t *reg_ptr;
ehci_writel(reg_ptr, tmp);
}
-void ehci_set_usbmode(int index)
- __attribute__((weak, alias("__ehci_set_usbmode")));
-
-void __ehci_powerup_fixup(uint32_t *status_reg, uint32_t *reg)
+__weak void ehci_powerup_fixup(uint32_t *status_reg, uint32_t *reg)
{
mdelay(50);
}
-void ehci_powerup_fixup(uint32_t *status_reg, uint32_t *reg)
- __attribute__((weak, alias("__ehci_powerup_fixup")));
-
static int handshake(uint32_t *ptr, uint32_t mask, uint32_t done, int usec)
{
uint32_t result;
return ret;
}
+static int ehci_shutdown(struct ehci_ctrl *ctrl)
+{
+ int i, ret = 0;
+ uint32_t cmd, reg;
+
+ if (!ctrl || !ctrl->hcor)
+ return -EINVAL;
+
+ cmd = ehci_readl(&ctrl->hcor->or_usbcmd);
+ cmd &= ~(CMD_PSE | CMD_ASE);
+ ehci_writel(&ctrl->hcor->or_usbcmd, cmd);
+ ret = handshake(&ctrl->hcor->or_usbsts, STS_ASS | STS_PSS, 0,
+ 100 * 1000);
+
+ if (!ret) {
+ for (i = 0; i < CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS; i++) {
+ reg = ehci_readl(&ctrl->hcor->or_portsc[i]);
+ reg |= EHCI_PS_SUSP;
+ ehci_writel(&ctrl->hcor->or_portsc[i], reg);
+ }
+
+ cmd &= ~CMD_RUN;
+ ehci_writel(&ctrl->hcor->or_usbcmd, cmd);
+ ret = handshake(&ctrl->hcor->or_usbsts, STS_HALT, STS_HALT,
+ HCHALT_TIMEOUT);
+ }
+
+ if (ret)
+ puts("EHCI failed to shut down host controller.\n");
+
+ return ret;
+}
+
static int ehci_td_buffer(struct qTD *td, void *buf, size_t sz)
{
uint32_t delta, next;
return QH_FULL_SPEED;
}
+static void ehci_update_endpt2_dev_n_port(struct usb_device *dev,
+ struct QH *qh)
+{
+ struct usb_device *ttdev;
+
+ if (dev->speed != USB_SPEED_LOW && dev->speed != USB_SPEED_FULL)
+ return;
+
+ /*
+ * For full / low speed devices we need to get the devnum and portnr of
+ * the tt, so of the first upstream usb-2 hub, there may be usb-1 hubs
+ * in the tree before that one!
+ */
+ ttdev = dev;
+ while (ttdev->parent && ttdev->parent->speed != USB_SPEED_HIGH)
+ ttdev = ttdev->parent;
+ if (!ttdev->parent)
+ return;
+
+ qh->qh_endpt2 |= cpu_to_hc32(QH_ENDPT2_PORTNUM(ttdev->portnr) |
+ QH_ENDPT2_HUBADDR(ttdev->parent->devnum));
+}
+
static int
ehci_submit_async(struct usb_device *dev, unsigned long pipe, void *buffer,
int length, struct devrequest *req)
QH_ENDPT1_ENDPT(usb_pipeendpoint(pipe)) | QH_ENDPT1_I(0) |
QH_ENDPT1_DEVADDR(usb_pipedevice(pipe));
qh->qh_endpt1 = cpu_to_hc32(endpt);
- endpt = QH_ENDPT2_MULT(1) | QH_ENDPT2_PORTNUM(dev->portnr) |
- QH_ENDPT2_HUBADDR(dev->parent->devnum) |
- QH_ENDPT2_UFCMASK(0) | QH_ENDPT2_UFSMASK(0);
+ endpt = QH_ENDPT2_MULT(1) | QH_ENDPT2_UFCMASK(0) | QH_ENDPT2_UFSMASK(0);
qh->qh_endpt2 = cpu_to_hc32(endpt);
+ ehci_update_endpt2_dev_n_port(dev, qh);
qh->qh_overlay.qt_next = cpu_to_hc32(QT_NEXT_TERMINATE);
+ qh->qh_overlay.qt_altnext = cpu_to_hc32(QT_NEXT_TERMINATE);
tdp = &qh->qh_overlay.qt_next;
dev->act_len = length - QT_TOKEN_GET_TOTALBYTES(token);
} else {
dev->act_len = 0;
+#ifndef CONFIG_USB_EHCI_FARADAY
debug("dev=%u, usbsts=%#x, p[1]=%#x, p[2]=%#x\n",
dev->devnum, ehci_readl(&ctrl->hcor->or_usbsts),
ehci_readl(&ctrl->hcor->or_portsc[0]),
ehci_readl(&ctrl->hcor->or_portsc[1]));
+#endif
}
free(qtd);
}
break;
case USB_PORT_FEAT_TEST:
+ ehci_shutdown(ctrl);
reg &= ~(0xf << 16);
reg |= ((le16_to_cpu(req->index) >> 8) & 0xf) << 16;
ehci_writel(status_reg, reg);
int usb_lowlevel_stop(int index)
{
+ ehci_shutdown(&ehcic[index]);
return ehci_hcd_stop(index);
}
-int usb_lowlevel_init(int index, void **controller)
+int usb_lowlevel_init(int index, enum usb_init_type init, void **controller)
{
uint32_t reg;
uint32_t cmd;
struct QH *qh_list;
struct QH *periodic;
int i;
+ int rc;
- if (ehci_hcd_init(index, &ehcic[index].hccr, &ehcic[index].hcor))
- return -1;
+ rc = ehci_hcd_init(index, init, &ehcic[index].hccr, &ehcic[index].hcor);
+ if (rc)
+ return rc;
+ if (init == USB_INIT_DEVICE)
+ goto done;
/* EHCI spec section 4.1 */
if (ehci_reset(index))
return -1;
#if defined(CONFIG_EHCI_HCD_INIT_AFTER_RESET)
- if (ehci_hcd_init(index, &ehcic[index].hccr, &ehcic[index].hcor))
- return -1;
+ rc = ehci_hcd_init(index, init, &ehcic[index].hccr, &ehcic[index].hcor);
+ if (rc)
+ return rc;
#endif
/* Set the high address word (aka segment) for 64-bit controller */
if (ehci_readl(&ehcic[index].hccr->cr_hccparams) & 1)
- ehci_writel(ehcic[index].hcor->or_ctrldssegment, 0);
+ ehci_writel(&ehcic[index].hcor->or_ctrldssegment, 0);
qh_list = &ehcic[index].qh_list;
qh_list->qh_overlay.qt_token =
cpu_to_hc32(QT_TOKEN_STATUS(QT_TOKEN_STATUS_HALTED));
+ flush_dcache_range((uint32_t)qh_list,
+ ALIGN_END_ADDR(struct QH, qh_list, 1));
+
/* Set async. queue head pointer. */
ehci_writel(&ehcic[index].hcor->or_asynclistaddr, (uint32_t)qh_list);
* Set up periodic list
* Step 1: Parent QH for all periodic transfers.
*/
+ ehcic[index].periodic_schedules = 0;
periodic = &ehcic[index].periodic_queue;
memset(periodic, 0, sizeof(*periodic));
periodic->qh_link = cpu_to_hc32(QH_LINK_TERMINATE);
periodic->qh_overlay.qt_next = cpu_to_hc32(QT_NEXT_TERMINATE);
periodic->qh_overlay.qt_altnext = cpu_to_hc32(QT_NEXT_TERMINATE);
+ flush_dcache_range((uint32_t)periodic,
+ ALIGN_END_ADDR(struct QH, periodic, 1));
+
/*
* Step 2: Setup frame-list: Every microframe, USB tries the same list.
* In particular, device specifications on polling frequency
* Split Transactions will be spread across microframes using
* S-mask and C-mask.
*/
- ehcic[index].periodic_list = memalign(4096, 1024*4);
+ if (ehcic[index].periodic_list == NULL)
+ ehcic[index].periodic_list = memalign(4096, 1024 * 4);
+
if (!ehcic[index].periodic_list)
return -ENOMEM;
for (i = 0; i < 1024; i++) {
- ehcic[index].periodic_list[i] = (uint32_t)periodic
- | QH_LINK_TYPE_QH;
+ ehcic[index].periodic_list[i] = cpu_to_hc32((uint32_t)periodic
+ | QH_LINK_TYPE_QH);
}
+ flush_dcache_range((uint32_t)ehcic[index].periodic_list,
+ ALIGN_END_ADDR(uint32_t, ehcic[index].periodic_list,
+ 1024));
+
/* Set periodic list base address */
ehci_writel(&ehcic[index].hcor->or_periodiclistbase,
(uint32_t)ehcic[index].periodic_list);
cmd |= CMD_RUN;
ehci_writel(&ehcic[index].hcor->or_usbcmd, cmd);
+#ifndef CONFIG_USB_EHCI_FARADAY
/* take control over the ports */
cmd = ehci_readl(&ehcic[index].hcor->or_configflag);
cmd |= FLAG_CF;
ehci_writel(&ehcic[index].hcor->or_configflag, cmd);
+#endif
+
/* unblock posted write */
cmd = ehci_readl(&ehcic[index].hcor->or_usbcmd);
mdelay(5);
printf("USB EHCI %x.%02x\n", reg >> 8, reg & 0xff);
ehcic[index].rootdev = 0;
-
+done:
*controller = &ehcic[index];
return 0;
}
}
struct int_queue {
+ int elementsize;
struct QH *first;
struct QH *current;
struct QH *last;
struct qTD *tds;
};
-#define NEXT_QH(qh) (struct QH *)((qh)->qh_link & ~0x1f)
+#define NEXT_QH(qh) (struct QH *)(hc32_to_cpu((qh)->qh_link) & ~0x1f)
static int
enable_periodic(struct ehci_ctrl *ctrl)
return 0;
}
-static int periodic_schedules;
-
struct int_queue *
create_int_queue(struct usb_device *dev, unsigned long pipe, int queuesize,
int elementsize, void *buffer)
struct int_queue *result = NULL;
int i;
+ /*
+ * Interrupt transfers requiring several transactions are not supported
+ * because bInterval is ignored.
+ *
+ * Also, ehci_submit_async() relies on wMaxPacketSize being a power of 2
+ * <= PKT_ALIGN if several qTDs are required, while the USB
+ * specification does not constrain this for interrupt transfers. That
+ * means that ehci_submit_async() would support interrupt transfers
+ * requiring several transactions only as long as the transfer size does
+ * not require more than a single qTD.
+ */
+ if (elementsize > usb_maxpacket(dev, pipe)) {
+ printf("%s: xfers requiring several transactions are not supported.\n",
+ __func__);
+ return NULL;
+ }
+
debug("Enter create_int_queue\n");
if (usb_pipetype(pipe) != PIPE_INTERRUPT) {
debug("non-interrupt pipe (type=%lu)", usb_pipetype(pipe));
debug("ehci intr queue: out of memory\n");
goto fail1;
}
- result->first = memalign(32, sizeof(struct QH) * queuesize);
+ result->elementsize = elementsize;
+ result->first = memalign(USB_DMA_MINALIGN,
+ sizeof(struct QH) * queuesize);
if (!result->first) {
debug("ehci intr queue: out of memory\n");
goto fail2;
}
result->current = result->first;
result->last = result->first + queuesize - 1;
- result->tds = memalign(32, sizeof(struct qTD) * queuesize);
+ result->tds = memalign(USB_DMA_MINALIGN,
+ sizeof(struct qTD) * queuesize);
if (!result->tds) {
debug("ehci intr queue: out of memory\n");
goto fail3;
struct qTD *td = result->tds + i;
void **buf = &qh->buffer;
- qh->qh_link = (uint32_t)(qh+1) | QH_LINK_TYPE_QH;
+ qh->qh_link = cpu_to_hc32((uint32_t)(qh+1) | QH_LINK_TYPE_QH);
if (i == queuesize - 1)
- qh->qh_link = QH_LINK_TERMINATE;
+ qh->qh_link = cpu_to_hc32(QH_LINK_TERMINATE);
- qh->qh_overlay.qt_next = (uint32_t)td;
- qh->qh_endpt1 = (0 << 28) | /* No NAK reload (ehci 4.9) */
+ qh->qh_overlay.qt_next = cpu_to_hc32((uint32_t)td);
+ qh->qh_overlay.qt_altnext = cpu_to_hc32(QT_NEXT_TERMINATE);
+ qh->qh_endpt1 =
+ cpu_to_hc32((0 << 28) | /* No NAK reload (ehci 4.9) */
(usb_maxpacket(dev, pipe) << 16) | /* MPS */
(1 << 14) |
QH_ENDPT1_EPS(ehci_encode_speed(dev->speed)) |
(usb_pipeendpoint(pipe) << 8) | /* Endpoint Number */
- (usb_pipedevice(pipe) << 0);
- qh->qh_endpt2 = (1 << 30) | /* 1 Tx per mframe */
- (1 << 0); /* S-mask: microframe 0 */
+ (usb_pipedevice(pipe) << 0));
+ qh->qh_endpt2 = cpu_to_hc32((1 << 30) | /* 1 Tx per mframe */
+ (1 << 0)); /* S-mask: microframe 0 */
if (dev->speed == USB_SPEED_LOW ||
dev->speed == USB_SPEED_FULL) {
- debug("TT: port: %d, hub address: %d\n",
- dev->portnr, dev->parent->devnum);
- qh->qh_endpt2 |= (dev->portnr << 23) |
- (dev->parent->devnum << 16) |
- (0x1c << 8); /* C-mask: microframes 2-4 */
+ /* C-mask: microframes 2-4 */
+ qh->qh_endpt2 |= cpu_to_hc32((0x1c << 8));
}
+ ehci_update_endpt2_dev_n_port(dev, qh);
- td->qt_next = QT_NEXT_TERMINATE;
- td->qt_altnext = QT_NEXT_TERMINATE;
+ td->qt_next = cpu_to_hc32(QT_NEXT_TERMINATE);
+ td->qt_altnext = cpu_to_hc32(QT_NEXT_TERMINATE);
debug("communication direction is '%s'\n",
usb_pipein(pipe) ? "in" : "out");
- td->qt_token = (elementsize << 16) |
+ td->qt_token = cpu_to_hc32((elementsize << 16) |
((usb_pipein(pipe) ? 1 : 0) << 8) | /* IN/OUT token */
- 0x80; /* active */
- td->qt_buffer[0] = (uint32_t)buffer + i * elementsize;
- td->qt_buffer[1] = (td->qt_buffer[0] + 0x1000) & ~0xfff;
- td->qt_buffer[2] = (td->qt_buffer[0] + 0x2000) & ~0xfff;
- td->qt_buffer[3] = (td->qt_buffer[0] + 0x3000) & ~0xfff;
- td->qt_buffer[4] = (td->qt_buffer[0] + 0x4000) & ~0xfff;
+ 0x80); /* active */
+ td->qt_buffer[0] =
+ cpu_to_hc32((uint32_t)buffer + i * elementsize);
+ td->qt_buffer[1] =
+ cpu_to_hc32((td->qt_buffer[0] + 0x1000) & ~0xfff);
+ td->qt_buffer[2] =
+ cpu_to_hc32((td->qt_buffer[0] + 0x2000) & ~0xfff);
+ td->qt_buffer[3] =
+ cpu_to_hc32((td->qt_buffer[0] + 0x3000) & ~0xfff);
+ td->qt_buffer[4] =
+ cpu_to_hc32((td->qt_buffer[0] + 0x4000) & ~0xfff);
*buf = buffer + i * elementsize;
}
- if (disable_periodic(ctrl) < 0) {
- debug("FATAL: periodic should never fail, but did");
- goto fail3;
+ flush_dcache_range((uint32_t)buffer,
+ ALIGN_END_ADDR(char, buffer,
+ queuesize * elementsize));
+ flush_dcache_range((uint32_t)result->first,
+ ALIGN_END_ADDR(struct QH, result->first,
+ queuesize));
+ flush_dcache_range((uint32_t)result->tds,
+ ALIGN_END_ADDR(struct qTD, result->tds,
+ queuesize));
+
+ if (ctrl->periodic_schedules > 0) {
+ if (disable_periodic(ctrl) < 0) {
+ debug("FATAL: periodic should never fail, but did");
+ goto fail3;
+ }
}
/* hook up to periodic list */
struct QH *list = &ctrl->periodic_queue;
result->last->qh_link = list->qh_link;
- list->qh_link = (uint32_t)result->first | QH_LINK_TYPE_QH;
+ list->qh_link = cpu_to_hc32((uint32_t)result->first | QH_LINK_TYPE_QH);
+
+ flush_dcache_range((uint32_t)result->last,
+ ALIGN_END_ADDR(struct QH, result->last, 1));
+ flush_dcache_range((uint32_t)list,
+ ALIGN_END_ADDR(struct QH, list, 1));
if (enable_periodic(ctrl) < 0) {
debug("FATAL: periodic should never fail, but did");
goto fail3;
}
- periodic_schedules++;
+ ctrl->periodic_schedules++;
debug("Exit create_int_queue\n");
return result;
void *poll_int_queue(struct usb_device *dev, struct int_queue *queue)
{
struct QH *cur = queue->current;
+ struct qTD *cur_td;
/* depleted queue */
if (cur == NULL) {
return NULL;
}
/* still active */
- if (cur->qh_overlay.qt_token & 0x80) {
- debug("Exit poll_int_queue with no completed intr transfer. "
- "token is %x\n", cur->qh_overlay.qt_token);
+ cur_td = &queue->tds[queue->current - queue->first];
+ invalidate_dcache_range((uint32_t)cur_td,
+ ALIGN_END_ADDR(struct qTD, cur_td, 1));
+ if (QT_TOKEN_GET_STATUS(hc32_to_cpu(cur_td->qt_token)) &
+ QT_TOKEN_STATUS_ACTIVE) {
+ debug("Exit poll_int_queue with no completed intr transfer. token is %x\n",
+ hc32_to_cpu(cur_td->qt_token));
return NULL;
}
if (!(cur->qh_link & QH_LINK_TERMINATE))
queue->current++;
else
queue->current = NULL;
- debug("Exit poll_int_queue with completed intr transfer. "
- "token is %x at %p (first at %p)\n", cur->qh_overlay.qt_token,
- &cur->qh_overlay.qt_token, queue->first);
+
+ invalidate_dcache_range((uint32_t)cur->buffer,
+ ALIGN_END_ADDR(char, cur->buffer,
+ queue->elementsize));
+
+ debug("Exit poll_int_queue with completed intr transfer. token is %x at %p (first at %p)\n",
+ hc32_to_cpu(cur_td->qt_token), cur, queue->first);
return cur->buffer;
}
debug("FATAL: periodic should never fail, but did");
goto out;
}
- periodic_schedules--;
+ ctrl->periodic_schedules--;
struct QH *cur = &ctrl->periodic_queue;
timeout = get_timer(0) + 500; /* abort after 500ms */
- while (!(cur->qh_link & QH_LINK_TERMINATE)) {
+ while (!(cur->qh_link & cpu_to_hc32(QH_LINK_TERMINATE))) {
debug("considering %p, with qh_link %x\n", cur, cur->qh_link);
if (NEXT_QH(cur) == queue->first) {
debug("found candidate. removing from chain\n");
cur->qh_link = queue->last->qh_link;
+ flush_dcache_range((uint32_t)cur,
+ ALIGN_END_ADDR(struct QH, cur, 1));
result = 0;
break;
}
}
}
- if (periodic_schedules > 0) {
+ if (ctrl->periodic_schedules > 0) {
result = enable_periodic(ctrl);
if (result < 0)
debug("FATAL: periodic should never fail, but did");
debug("dev=%p, pipe=%lu, buffer=%p, length=%d, interval=%d",
dev, pipe, buffer, length, interval);
- /*
- * Interrupt transfers requiring several transactions are not supported
- * because bInterval is ignored.
- *
- * Also, ehci_submit_async() relies on wMaxPacketSize being a power of 2
- * <= PKT_ALIGN if several qTDs are required, while the USB
- * specification does not constrain this for interrupt transfers. That
- * means that ehci_submit_async() would support interrupt transfers
- * requiring several transactions only as long as the transfer size does
- * not require more than a single qTD.
- */
- if (length > usb_maxpacket(dev, pipe)) {
- printf("%s: Interrupt transfers requiring several "
- "transactions are not supported.\n", __func__);
- return -1;
- }
-
queue = create_int_queue(dev, pipe, 1, length, buffer);
+ if (!queue)
+ return -1;
timeout = get_timer(0) + USB_TIMEOUT_MS(pipe);
while ((backbuffer = poll_int_queue(dev, queue)) == NULL)