switch ( action ) {
case ACTION_READ_STATUS:
- US_DEBUGP(" isd200_action(READ_STATUS)\n");
+ usb_stor_dbg(us, " isd200_action(READ_STATUS)\n");
ata.generic.ActionSelect = ACTION_SELECT_0|ACTION_SELECT_2;
ata.generic.RegisterSelect =
REG_CYLINDER_LOW | REG_CYLINDER_HIGH |
break;
case ACTION_ENUM:
- US_DEBUGP(" isd200_action(ENUM,0x%02x)\n",value);
+ usb_stor_dbg(us, " isd200_action(ENUM,0x%02x)\n", value);
ata.generic.ActionSelect = ACTION_SELECT_1|ACTION_SELECT_2|
ACTION_SELECT_3|ACTION_SELECT_4|
ACTION_SELECT_5;
break;
case ACTION_RESET:
- US_DEBUGP(" isd200_action(RESET)\n");
+ usb_stor_dbg(us, " isd200_action(RESET)\n");
ata.generic.ActionSelect = ACTION_SELECT_1|ACTION_SELECT_2|
ACTION_SELECT_3|ACTION_SELECT_4;
ata.generic.RegisterSelect = REG_DEVICE_CONTROL;
break;
case ACTION_REENABLE:
- US_DEBUGP(" isd200_action(REENABLE)\n");
+ usb_stor_dbg(us, " isd200_action(REENABLE)\n");
ata.generic.ActionSelect = ACTION_SELECT_1|ACTION_SELECT_2|
ACTION_SELECT_3|ACTION_SELECT_4;
ata.generic.RegisterSelect = REG_DEVICE_CONTROL;
break;
case ACTION_SOFT_RESET:
- US_DEBUGP(" isd200_action(SOFT_RESET)\n");
+ usb_stor_dbg(us, " isd200_action(SOFT_RESET)\n");
ata.generic.ActionSelect = ACTION_SELECT_1|ACTION_SELECT_5;
ata.generic.RegisterSelect = REG_DEVICE_HEAD | REG_COMMAND;
ata.write.DeviceHeadByte = info->DeviceHead;
break;
case ACTION_IDENTIFY:
- US_DEBUGP(" isd200_action(IDENTIFY)\n");
+ usb_stor_dbg(us, " isd200_action(IDENTIFY)\n");
ata.generic.RegisterSelect = REG_COMMAND;
ata.write.CommandByte = ATA_CMD_ID_ATA;
isd200_set_srb(info, DMA_FROM_DEVICE, info->id,
break;
default:
- US_DEBUGP("Error: Undefined action %d\n",action);
+ usb_stor_dbg(us, "Error: Undefined action %d\n", action);
return ISD200_ERROR;
}
if (status == USB_STOR_TRANSPORT_GOOD)
status = ISD200_GOOD;
else {
- US_DEBUGP(" isd200_action(0x%02x) error: %d\n",action,status);
+ usb_stor_dbg(us, " isd200_action(0x%02x) error: %d\n",
+ action, status);
status = ISD200_ERROR;
/* need to reset device here */
}
int retStatus = ISD200_GOOD;
int transferStatus;
- US_DEBUGP("Entering isd200_IssueATAReadRegs\n");
+ usb_stor_dbg(us, "Entering isd200_IssueATAReadRegs\n");
transferStatus = isd200_action( us, ACTION_READ_STATUS,
info->RegsBuf, sizeof(info->ATARegs) );
if (transferStatus != ISD200_TRANSPORT_GOOD) {
- US_DEBUGP(" Error reading ATA registers\n");
+ usb_stor_dbg(us, " Error reading ATA registers\n");
retStatus = ISD200_ERROR;
} else {
memcpy(info->ATARegs, info->RegsBuf, sizeof(info->ATARegs));
- US_DEBUGP(" Got ATA Register[ATA_REG_ERROR_OFFSET] = 0x%x\n",
- info->ATARegs[ATA_REG_ERROR_OFFSET]);
+ usb_stor_dbg(us, " Got ATA Register[ATA_REG_ERROR_OFFSET] = 0x%x\n",
+ info->ATARegs[ATA_REG_ERROR_OFFSET]);
}
return retStatus;
* short-circuit all other processing
*/
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
- US_DEBUGP("-- command was aborted\n");
+ usb_stor_dbg(us, "-- command was aborted\n");
goto Handle_Abort;
}
break;
case USB_STOR_TRANSPORT_NO_SENSE:
- US_DEBUGP("-- transport indicates protocol failure\n");
+ usb_stor_dbg(us, "-- transport indicates protocol failure\n");
srb->result = SAM_STAT_CHECK_CONDITION;
return;
case USB_STOR_TRANSPORT_FAILED:
- US_DEBUGP("-- transport indicates command failure\n");
+ usb_stor_dbg(us, "-- transport indicates command failure\n");
need_auto_sense = 1;
break;
case USB_STOR_TRANSPORT_ERROR:
- US_DEBUGP("-- transport indicates transport error\n");
+ usb_stor_dbg(us, "-- transport indicates transport error\n");
srb->result = DID_ERROR << 16;
/* Need reset here */
return;
default:
- US_DEBUGP("-- transport indicates unknown error\n");
+ usb_stor_dbg(us, "-- transport indicates unknown error\n");
srb->result = DID_ERROR << 16;
/* Need reset here */
return;
(srb->cmnd[0] == MODE_SENSE) ||
(srb->cmnd[0] == LOG_SENSE) ||
(srb->cmnd[0] == MODE_SENSE_10))) {
- US_DEBUGP("-- unexpectedly short transfer\n");
+ usb_stor_dbg(us, "-- unexpectedly short transfer\n");
need_auto_sense = 1;
}
if (need_auto_sense) {
result = isd200_read_regs(us);
if (test_bit(US_FLIDX_TIMED_OUT, &us->dflags)) {
- US_DEBUGP("-- auto-sense aborted\n");
+ usb_stor_dbg(us, "-- auto-sense aborted\n");
goto Handle_Abort;
}
if (result == ISD200_GOOD) {
}
#ifdef CONFIG_USB_STORAGE_DEBUG
-static void isd200_log_config( struct isd200_info* info )
+static void isd200_log_config(struct us_data *us, struct isd200_info *info)
{
- US_DEBUGP(" Event Notification: 0x%x\n",
- info->ConfigData.EventNotification);
- US_DEBUGP(" External Clock: 0x%x\n",
- info->ConfigData.ExternalClock);
- US_DEBUGP(" ATA Init Timeout: 0x%x\n",
- info->ConfigData.ATAInitTimeout);
- US_DEBUGP(" ATAPI Command Block Size: 0x%x\n",
- (info->ConfigData.ATAConfig & ATACFG_BLOCKSIZE) >> 6);
- US_DEBUGP(" Master/Slave Selection: 0x%x\n",
- info->ConfigData.ATAConfig & ATACFG_MASTER);
- US_DEBUGP(" ATAPI Reset: 0x%x\n",
- info->ConfigData.ATAConfig & ATACFG_ATAPI_RESET);
- US_DEBUGP(" ATA Timing: 0x%x\n",
- info->ConfigData.ATAConfig & ATACFG_TIMING);
- US_DEBUGP(" ATA Major Command: 0x%x\n",
- info->ConfigData.ATAMajorCommand);
- US_DEBUGP(" ATA Minor Command: 0x%x\n",
- info->ConfigData.ATAMinorCommand);
- US_DEBUGP(" Init Status: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_INIT_STATUS);
- US_DEBUGP(" Config Descriptor 2: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_CONF_DESC2);
- US_DEBUGP(" Skip Device Boot: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_SKIP_BOOT);
- US_DEBUGP(" ATA 3 State Supsend: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_STATE_SUSPEND);
- US_DEBUGP(" Descriptor Override: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_DESC_OVERRIDE);
- US_DEBUGP(" Last LUN Identifier: 0x%x\n",
- info->ConfigData.ATAExtraConfig & ATACFGE_LAST_LUN);
- US_DEBUGP(" SRST Enable: 0x%x\n",
- info->ConfigData.ATAExtraConfig & CFG_CAPABILITY_SRST);
+ usb_stor_dbg(us, " Event Notification: 0x%x\n",
+ info->ConfigData.EventNotification);
+ usb_stor_dbg(us, " External Clock: 0x%x\n",
+ info->ConfigData.ExternalClock);
+ usb_stor_dbg(us, " ATA Init Timeout: 0x%x\n",
+ info->ConfigData.ATAInitTimeout);
+ usb_stor_dbg(us, " ATAPI Command Block Size: 0x%x\n",
+ (info->ConfigData.ATAConfig & ATACFG_BLOCKSIZE) >> 6);
+ usb_stor_dbg(us, " Master/Slave Selection: 0x%x\n",
+ info->ConfigData.ATAConfig & ATACFG_MASTER);
+ usb_stor_dbg(us, " ATAPI Reset: 0x%x\n",
+ info->ConfigData.ATAConfig & ATACFG_ATAPI_RESET);
+ usb_stor_dbg(us, " ATA Timing: 0x%x\n",
+ info->ConfigData.ATAConfig & ATACFG_TIMING);
+ usb_stor_dbg(us, " ATA Major Command: 0x%x\n",
+ info->ConfigData.ATAMajorCommand);
+ usb_stor_dbg(us, " ATA Minor Command: 0x%x\n",
+ info->ConfigData.ATAMinorCommand);
+ usb_stor_dbg(us, " Init Status: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_INIT_STATUS);
+ usb_stor_dbg(us, " Config Descriptor 2: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_CONF_DESC2);
+ usb_stor_dbg(us, " Skip Device Boot: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_SKIP_BOOT);
+ usb_stor_dbg(us, " ATA 3 State Supsend: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_STATE_SUSPEND);
+ usb_stor_dbg(us, " Descriptor Override: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_DESC_OVERRIDE);
+ usb_stor_dbg(us, " Last LUN Identifier: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & ATACFGE_LAST_LUN);
+ usb_stor_dbg(us, " SRST Enable: 0x%x\n",
+ info->ConfigData.ATAExtraConfig & CFG_CAPABILITY_SRST);
}
#endif
int result;
#ifdef CONFIG_USB_STORAGE_DEBUG
- US_DEBUGP("Entering isd200_write_config\n");
- US_DEBUGP(" Writing the following ISD200 Config Data:\n");
- isd200_log_config(info);
+ usb_stor_dbg(us, "Entering isd200_write_config\n");
+ usb_stor_dbg(us, " Writing the following ISD200 Config Data:\n");
+ isd200_log_config(us, info);
#endif
/* let's send the command via the control pipe */
sizeof(info->ConfigData));
if (result >= 0) {
- US_DEBUGP(" ISD200 Config Data was written successfully\n");
+ usb_stor_dbg(us, " ISD200 Config Data was written successfully\n");
} else {
- US_DEBUGP(" Request to write ISD200 Config Data failed!\n");
+ usb_stor_dbg(us, " Request to write ISD200 Config Data failed!\n");
retStatus = ISD200_ERROR;
}
- US_DEBUGP("Leaving isd200_write_config %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_write_config %08X\n", retStatus);
return retStatus;
}
int retStatus = ISD200_GOOD;
int result;
- US_DEBUGP("Entering isd200_read_config\n");
+ usb_stor_dbg(us, "Entering isd200_read_config\n");
/* read the configuration information from ISD200. Use this to */
/* determine what the special ATA CDB bytes are. */
if (result >= 0) {
- US_DEBUGP(" Retrieved the following ISD200 Config Data:\n");
+ usb_stor_dbg(us, " Retrieved the following ISD200 Config Data:\n");
#ifdef CONFIG_USB_STORAGE_DEBUG
- isd200_log_config(info);
+ isd200_log_config(us, info);
#endif
} else {
- US_DEBUGP(" Request to get ISD200 Config Data failed!\n");
+ usb_stor_dbg(us, " Request to get ISD200 Config Data failed!\n");
retStatus = ISD200_ERROR;
}
- US_DEBUGP("Leaving isd200_read_config %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_read_config %08X\n", retStatus);
return retStatus;
}
int retStatus = ISD200_GOOD;
int transferStatus;
- US_DEBUGP("Entering isd200_atapi_soft_reset\n");
+ usb_stor_dbg(us, "Entering isd200_atapi_soft_reset\n");
transferStatus = isd200_action( us, ACTION_SOFT_RESET, NULL, 0 );
if (transferStatus != ISD200_TRANSPORT_GOOD) {
- US_DEBUGP(" Error issuing Atapi Soft Reset\n");
+ usb_stor_dbg(us, " Error issuing Atapi Soft Reset\n");
retStatus = ISD200_ERROR;
}
- US_DEBUGP("Leaving isd200_atapi_soft_reset %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_atapi_soft_reset %08X\n", retStatus);
return retStatus;
}
int retStatus = ISD200_GOOD;
int transferStatus;
- US_DEBUGP("Entering isd200_SRST\n");
+ usb_stor_dbg(us, "Entering isd200_SRST\n");
transferStatus = isd200_action( us, ACTION_RESET, NULL, 0 );
/* check to see if this request failed */
if (transferStatus != ISD200_TRANSPORT_GOOD) {
- US_DEBUGP(" Error issuing SRST\n");
+ usb_stor_dbg(us, " Error issuing SRST\n");
retStatus = ISD200_ERROR;
} else {
/* delay 10ms to give the drive a chance to see it */
transferStatus = isd200_action( us, ACTION_REENABLE, NULL, 0 );
if (transferStatus != ISD200_TRANSPORT_GOOD) {
- US_DEBUGP(" Error taking drive out of reset\n");
+ usb_stor_dbg(us, " Error taking drive out of reset\n");
retStatus = ISD200_ERROR;
} else {
/* delay 50ms to give the drive a chance to recover after SRST */
}
}
- US_DEBUGP("Leaving isd200_srst %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_srst %08X\n", retStatus);
return retStatus;
}
/* loop until we detect !BSY or timeout */
while(1) {
-#ifdef CONFIG_USB_STORAGE_DEBUG
- char* mstr = master_slave == ATA_ADDRESS_DEVHEAD_STD ?
- "Master" : "Slave";
-#endif
status = isd200_action( us, ACTION_ENUM, NULL, master_slave );
if ( status != ISD200_GOOD )
if (!detect) {
if (regs[ATA_REG_STATUS_OFFSET] & ATA_BUSY) {
- US_DEBUGP(" %s status is still BSY, try again...\n",mstr);
+ usb_stor_dbg(us, " %s status is still BSY, try again...\n",
+ master_slave == ATA_ADDRESS_DEVHEAD_STD ?
+ "Master" : "Slave");
} else {
- US_DEBUGP(" %s status !BSY, continue with next operation\n",mstr);
+ usb_stor_dbg(us, " %s status !BSY, continue with next operation\n",
+ master_slave == ATA_ADDRESS_DEVHEAD_STD ?
+ "Master" : "Slave");
break;
}
}
/* ATA_ERR (workaround for Archos CD-ROM) */
else if (regs[ATA_REG_STATUS_OFFSET] &
(ATA_BUSY | ATA_DF | ATA_ERR)) {
- US_DEBUGP(" Status indicates it is not ready, try again...\n");
+ usb_stor_dbg(us, " Status indicates it is not ready, try again...\n");
}
/* check for DRDY, ATA devices set DRDY after SRST */
else if (regs[ATA_REG_STATUS_OFFSET] & ATA_DRDY) {
- US_DEBUGP(" Identified ATA device\n");
+ usb_stor_dbg(us, " Identified ATA device\n");
info->DeviceFlags |= DF_ATA_DEVICE;
info->DeviceHead = master_slave;
break;
*/
if ((master_slave & ATA_ADDRESS_DEVHEAD_SLAVE) &&
!recheckAsMaster) {
- US_DEBUGP(" Identified ATAPI device as slave. Rechecking again as master\n");
+ usb_stor_dbg(us, " Identified ATAPI device as slave. Rechecking again as master\n");
recheckAsMaster = 1;
master_slave = ATA_ADDRESS_DEVHEAD_STD;
} else {
- US_DEBUGP(" Identified ATAPI device\n");
+ usb_stor_dbg(us, " Identified ATAPI device\n");
info->DeviceHead = master_slave;
status = isd200_atapi_soft_reset(us);
break;
}
} else {
- US_DEBUGP(" Not ATA, not ATAPI. Weird.\n");
+ usb_stor_dbg(us, " Not ATA, not ATAPI - Weird\n");
break;
}
/* check for timeout on this request */
if (time_after_eq(jiffies, endTime)) {
if (!detect)
- US_DEBUGP(" BSY check timeout, just continue with next operation...\n");
+ usb_stor_dbg(us, " BSY check timeout, just continue with next operation...\n");
else
- US_DEBUGP(" Device detect timeout!\n");
+ usb_stor_dbg(us, " Device detect timeout!\n");
break;
}
}
struct isd200_info *info = (struct isd200_info *)us->extra;
int retStatus = ISD200_GOOD;
- US_DEBUGP("Entering isd200_manual_enum\n");
+ usb_stor_dbg(us, "Entering isd200_manual_enum\n");
retStatus = isd200_read_config(us);
if (retStatus == ISD200_GOOD) {
isslave = (info->DeviceHead & ATA_ADDRESS_DEVHEAD_SLAVE) ? 1 : 0;
if (!(info->ConfigData.ATAConfig & ATACFG_MASTER)) {
- US_DEBUGP(" Setting Master/Slave selection to %d\n", isslave);
+ usb_stor_dbg(us, " Setting Master/Slave selection to %d\n",
+ isslave);
info->ConfigData.ATAConfig &= 0x3f;
info->ConfigData.ATAConfig |= (isslave<<6);
retStatus = isd200_write_config(us);
}
}
- US_DEBUGP("Leaving isd200_manual_enum %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_manual_enum %08X\n", retStatus);
return(retStatus);
}
#endif
}
-static void isd200_dump_driveid(u16 *id)
+static void isd200_dump_driveid(struct us_data *us, u16 *id)
{
- US_DEBUGP(" Identify Data Structure:\n");
- US_DEBUGP(" config = 0x%x\n", id[ATA_ID_CONFIG]);
- US_DEBUGP(" cyls = 0x%x\n", id[ATA_ID_CYLS]);
- US_DEBUGP(" heads = 0x%x\n", id[ATA_ID_HEADS]);
- US_DEBUGP(" track_bytes = 0x%x\n", id[4]);
- US_DEBUGP(" sector_bytes = 0x%x\n", id[5]);
- US_DEBUGP(" sectors = 0x%x\n", id[ATA_ID_SECTORS]);
- US_DEBUGP(" serial_no[0] = 0x%x\n", *(char *)&id[ATA_ID_SERNO]);
- US_DEBUGP(" buf_type = 0x%x\n", id[20]);
- US_DEBUGP(" buf_size = 0x%x\n", id[ATA_ID_BUF_SIZE]);
- US_DEBUGP(" ecc_bytes = 0x%x\n", id[22]);
- US_DEBUGP(" fw_rev[0] = 0x%x\n", *(char *)&id[ATA_ID_FW_REV]);
- US_DEBUGP(" model[0] = 0x%x\n", *(char *)&id[ATA_ID_PROD]);
- US_DEBUGP(" max_multsect = 0x%x\n", id[ATA_ID_MAX_MULTSECT] & 0xff);
- US_DEBUGP(" dword_io = 0x%x\n", id[ATA_ID_DWORD_IO]);
- US_DEBUGP(" capability = 0x%x\n", id[ATA_ID_CAPABILITY] >> 8);
- US_DEBUGP(" tPIO = 0x%x\n", id[ATA_ID_OLD_PIO_MODES] >> 8);
- US_DEBUGP(" tDMA = 0x%x\n", id[ATA_ID_OLD_DMA_MODES] >> 8);
- US_DEBUGP(" field_valid = 0x%x\n", id[ATA_ID_FIELD_VALID]);
- US_DEBUGP(" cur_cyls = 0x%x\n", id[ATA_ID_CUR_CYLS]);
- US_DEBUGP(" cur_heads = 0x%x\n", id[ATA_ID_CUR_HEADS]);
- US_DEBUGP(" cur_sectors = 0x%x\n", id[ATA_ID_CUR_SECTORS]);
- US_DEBUGP(" cur_capacity = 0x%x\n", ata_id_u32(id, 57));
- US_DEBUGP(" multsect = 0x%x\n", id[ATA_ID_MULTSECT] & 0xff);
- US_DEBUGP(" lba_capacity = 0x%x\n", ata_id_u32(id, ATA_ID_LBA_CAPACITY));
- US_DEBUGP(" command_set_1 = 0x%x\n", id[ATA_ID_COMMAND_SET_1]);
- US_DEBUGP(" command_set_2 = 0x%x\n", id[ATA_ID_COMMAND_SET_2]);
+ usb_stor_dbg(us, " Identify Data Structure:\n");
+ usb_stor_dbg(us, " config = 0x%x\n", id[ATA_ID_CONFIG]);
+ usb_stor_dbg(us, " cyls = 0x%x\n", id[ATA_ID_CYLS]);
+ usb_stor_dbg(us, " heads = 0x%x\n", id[ATA_ID_HEADS]);
+ usb_stor_dbg(us, " track_bytes = 0x%x\n", id[4]);
+ usb_stor_dbg(us, " sector_bytes = 0x%x\n", id[5]);
+ usb_stor_dbg(us, " sectors = 0x%x\n", id[ATA_ID_SECTORS]);
+ usb_stor_dbg(us, " serial_no[0] = 0x%x\n", *(char *)&id[ATA_ID_SERNO]);
+ usb_stor_dbg(us, " buf_type = 0x%x\n", id[20]);
+ usb_stor_dbg(us, " buf_size = 0x%x\n", id[ATA_ID_BUF_SIZE]);
+ usb_stor_dbg(us, " ecc_bytes = 0x%x\n", id[22]);
+ usb_stor_dbg(us, " fw_rev[0] = 0x%x\n", *(char *)&id[ATA_ID_FW_REV]);
+ usb_stor_dbg(us, " model[0] = 0x%x\n", *(char *)&id[ATA_ID_PROD]);
+ usb_stor_dbg(us, " max_multsect = 0x%x\n", id[ATA_ID_MAX_MULTSECT] & 0xff);
+ usb_stor_dbg(us, " dword_io = 0x%x\n", id[ATA_ID_DWORD_IO]);
+ usb_stor_dbg(us, " capability = 0x%x\n", id[ATA_ID_CAPABILITY] >> 8);
+ usb_stor_dbg(us, " tPIO = 0x%x\n", id[ATA_ID_OLD_PIO_MODES] >> 8);
+ usb_stor_dbg(us, " tDMA = 0x%x\n", id[ATA_ID_OLD_DMA_MODES] >> 8);
+ usb_stor_dbg(us, " field_valid = 0x%x\n", id[ATA_ID_FIELD_VALID]);
+ usb_stor_dbg(us, " cur_cyls = 0x%x\n", id[ATA_ID_CUR_CYLS]);
+ usb_stor_dbg(us, " cur_heads = 0x%x\n", id[ATA_ID_CUR_HEADS]);
+ usb_stor_dbg(us, " cur_sectors = 0x%x\n", id[ATA_ID_CUR_SECTORS]);
+ usb_stor_dbg(us, " cur_capacity = 0x%x\n", ata_id_u32(id, 57));
+ usb_stor_dbg(us, " multsect = 0x%x\n", id[ATA_ID_MULTSECT] & 0xff);
+ usb_stor_dbg(us, " lba_capacity = 0x%x\n", ata_id_u32(id, ATA_ID_LBA_CAPACITY));
+ usb_stor_dbg(us, " command_set_1 = 0x%x\n", id[ATA_ID_COMMAND_SET_1]);
+ usb_stor_dbg(us, " command_set_2 = 0x%x\n", id[ATA_ID_COMMAND_SET_2]);
}
/**************************************************************************
int retStatus = ISD200_GOOD;
u16 *id = info->id;
- US_DEBUGP("Entering isd200_get_inquiry_data\n");
+ usb_stor_dbg(us, "Entering isd200_get_inquiry_data\n");
/* set default to Master */
info->DeviceHead = ATA_ADDRESS_DEVHEAD_STD;
id, ATA_ID_WORDS * 2);
if (transferStatus != ISD200_TRANSPORT_GOOD) {
/* Error issuing ATA Command Identify */
- US_DEBUGP(" Error issuing ATA Command Identify\n");
+ usb_stor_dbg(us, " Error issuing ATA Command Identify\n");
retStatus = ISD200_ERROR;
} else {
/* ATA Command Identify successful */
__u16 *dest;
isd200_fix_driveid(id);
- isd200_dump_driveid(id);
+ isd200_dump_driveid(us, id);
memset(&info->InquiryData, 0, sizeof(info->InquiryData));
/* determine if it supports Media Status Notification */
if (id[ATA_ID_COMMAND_SET_2] & COMMANDSET_MEDIA_STATUS) {
- US_DEBUGP(" Device supports Media Status Notification\n");
+ usb_stor_dbg(us, " Device supports Media Status Notification\n");
/* Indicate that it is enabled, even though it is not
* This allows the lock/unlock of the media to work
us->protocol_name = "Transparent SCSI";
us->proto_handler = usb_stor_transparent_scsi_command;
- US_DEBUGP("Protocol changed to: %s\n", us->protocol_name);
+ usb_stor_dbg(us, "Protocol changed to: %s\n",
+ us->protocol_name);
/* Free driver structure */
us->extra_destructor(info);
}
}
- US_DEBUGP("Leaving isd200_get_inquiry_data %08X\n", retStatus);
+ usb_stor_dbg(us, "Leaving isd200_get_inquiry_data %08X\n", retStatus);
return(retStatus);
}
/* SCSI Command */
switch (srb->cmnd[0]) {
case INQUIRY:
- US_DEBUGP(" ATA OUT - INQUIRY\n");
+ usb_stor_dbg(us, " ATA OUT - INQUIRY\n");
/* copy InquiryData */
usb_stor_set_xfer_buf((unsigned char *) &info->InquiryData,
break;
case MODE_SENSE:
- US_DEBUGP(" ATA OUT - SCSIOP_MODE_SENSE\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_MODE_SENSE\n");
/* Initialize the return buffer */
usb_stor_set_xfer_buf(senseData, sizeof(senseData), srb);
ataCdb->write.CommandByte = ATA_COMMAND_GET_MEDIA_STATUS;
isd200_srb_set_bufflen(srb, 0);
} else {
- US_DEBUGP(" Media Status not supported, just report okay\n");
+ usb_stor_dbg(us, " Media Status not supported, just report okay\n");
srb->result = SAM_STAT_GOOD;
sendToTransport = 0;
}
break;
case TEST_UNIT_READY:
- US_DEBUGP(" ATA OUT - SCSIOP_TEST_UNIT_READY\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_TEST_UNIT_READY\n");
if (info->DeviceFlags & DF_MEDIA_STATUS_ENABLED)
{
ataCdb->write.CommandByte = ATA_COMMAND_GET_MEDIA_STATUS;
isd200_srb_set_bufflen(srb, 0);
} else {
- US_DEBUGP(" Media Status not supported, just report okay\n");
+ usb_stor_dbg(us, " Media Status not supported, just report okay\n");
srb->result = SAM_STAT_GOOD;
sendToTransport = 0;
}
unsigned long capacity;
struct read_capacity_data readCapacityData;
- US_DEBUGP(" ATA OUT - SCSIOP_READ_CAPACITY\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_READ_CAPACITY\n");
if (ata_id_has_lba(id))
capacity = ata_id_u32(id, ATA_ID_LBA_CAPACITY) - 1;
break;
case READ_10:
- US_DEBUGP(" ATA OUT - SCSIOP_READ\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_READ\n");
lba = be32_to_cpu(*(__be32 *)&srb->cmnd[2]);
blockCount = (unsigned long)srb->cmnd[7]<<8 | (unsigned long)srb->cmnd[8];
break;
case WRITE_10:
- US_DEBUGP(" ATA OUT - SCSIOP_WRITE\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_WRITE\n");
lba = be32_to_cpu(*(__be32 *)&srb->cmnd[2]);
blockCount = (unsigned long)srb->cmnd[7]<<8 | (unsigned long)srb->cmnd[8];
break;
case ALLOW_MEDIUM_REMOVAL:
- US_DEBUGP(" ATA OUT - SCSIOP_MEDIUM_REMOVAL\n");
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_MEDIUM_REMOVAL\n");
if (info->DeviceFlags & DF_REMOVABLE_MEDIA) {
- US_DEBUGP(" srb->cmnd[4] = 0x%X\n", srb->cmnd[4]);
+ usb_stor_dbg(us, " srb->cmnd[4] = 0x%X\n",
+ srb->cmnd[4]);
ataCdb->generic.SignatureByte0 = info->ConfigData.ATAMajorCommand;
ataCdb->generic.SignatureByte1 = info->ConfigData.ATAMinorCommand;
ATA_CMD_MEDIA_LOCK : ATA_CMD_MEDIA_UNLOCK;
isd200_srb_set_bufflen(srb, 0);
} else {
- US_DEBUGP(" Not removeable media, just report okay\n");
+ usb_stor_dbg(us, " Not removeable media, just report okay\n");
srb->result = SAM_STAT_GOOD;
sendToTransport = 0;
}
break;
case START_STOP:
- US_DEBUGP(" ATA OUT - SCSIOP_START_STOP_UNIT\n");
- US_DEBUGP(" srb->cmnd[4] = 0x%X\n", srb->cmnd[4]);
+ usb_stor_dbg(us, " ATA OUT - SCSIOP_START_STOP_UNIT\n");
+ usb_stor_dbg(us, " srb->cmnd[4] = 0x%X\n", srb->cmnd[4]);
if ((srb->cmnd[4] & 0x3) == 0x2) {
- US_DEBUGP(" Media Eject\n");
+ usb_stor_dbg(us, " Media Eject\n");
ataCdb->generic.SignatureByte0 = info->ConfigData.ATAMajorCommand;
ataCdb->generic.SignatureByte1 = info->ConfigData.ATAMinorCommand;
ataCdb->generic.TransferBlockSize = 0;
ataCdb->generic.RegisterSelect = REG_COMMAND;
ataCdb->write.CommandByte = ATA_COMMAND_MEDIA_EJECT;
} else if ((srb->cmnd[4] & 0x3) == 0x1) {
- US_DEBUGP(" Get Media Status\n");
+ usb_stor_dbg(us, " Get Media Status\n");
ataCdb->generic.SignatureByte0 = info->ConfigData.ATAMajorCommand;
ataCdb->generic.SignatureByte1 = info->ConfigData.ATAMinorCommand;
ataCdb->generic.TransferBlockSize = 1;
ataCdb->write.CommandByte = ATA_COMMAND_GET_MEDIA_STATUS;
isd200_srb_set_bufflen(srb, 0);
} else {
- US_DEBUGP(" Nothing to do, just report okay\n");
+ usb_stor_dbg(us, " Nothing to do, just report okay\n");
srb->result = SAM_STAT_GOOD;
sendToTransport = 0;
}
break;
default:
- US_DEBUGP("Unsupported SCSI command - 0x%X\n", srb->cmnd[0]);
+ usb_stor_dbg(us, "Unsupported SCSI command - 0x%X\n",
+ srb->cmnd[0]);
srb->result = DID_ERROR << 16;
sendToTransport = 0;
break;
if (retStatus == ISD200_GOOD) {
us->extra = info;
us->extra_destructor = isd200_free_info_ptrs;
- } else
- US_DEBUGP("ERROR - kmalloc failure\n");
+ }
return retStatus;
}
static int isd200_Initialization(struct us_data *us)
{
- US_DEBUGP("ISD200 Initialization...\n");
+ usb_stor_dbg(us, "ISD200 Initialization...\n");
/* Initialize ISD200 info struct */
if (isd200_init_info(us) == ISD200_ERROR) {
- US_DEBUGP("ERROR Initializing ISD200 Info struct\n");
+ usb_stor_dbg(us, "ERROR Initializing ISD200 Info struct\n");
} else {
/* Get device specific data */
if (isd200_get_inquiry_data(us) != ISD200_GOOD)
- US_DEBUGP("ISD200 Initialization Failure\n");
+ usb_stor_dbg(us, "ISD200 Initialization Failure\n");
else
- US_DEBUGP("ISD200 Initialization complete\n");
+ usb_stor_dbg(us, "ISD200 Initialization complete\n");
}
return 0;
/* Make sure driver was initialized */
if (us->extra == NULL)
- US_DEBUGP("ERROR Driver not initialized\n");
+ usb_stor_dbg(us, "ERROR Driver not initialized\n");
scsi_set_resid(srb, 0);
/* scsi_bufflen might change in protocol translation to ata */
projects / karo-tx-linux.git / blobdiff