ARM: remove broken "dnp1110" board.

[karo-tx-uboot.git] / include / configs / MPC8315ERDB.h

diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index b0f5cbde3dbc25ae2c4500949f760cb2d48b54ef..a0cfd000f23727f649f8f7b405bae28f4d34ff36 100644 (file)
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -25,9 +25,26 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#ifdef CONFIG_NAND
-#define CONFIG_NAND_U_BOOT             1
-#define CONFIG_RAMBOOT_TEXT_BASE       0x00100000
+#define CONFIG_SYS_NAND_U_BOOT_SIZE  (512 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST   0x00100000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00100100
+#define CONFIG_SYS_NAND_U_BOOT_OFFS  16384
+#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x00010000
+
+#ifdef CONFIG_NAND_U_BOOT
+#define CONFIG_SYS_TEXT_BASE   0x00100000 /* CONFIG_SYS_NAND_U_BOOT_DST */
+#define CONFIG_SYS_TEXT_BASE_SPL 0xfff00000
+#ifdef CONFIG_NAND_SPL
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE_SPL /* start of monitor */
+#endif /* CONFIG_NAND_SPL */
+#endif /* CONFIG_NAND_U_BOOT */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE   0xFE000000
+#endif
+
+#ifndef CONFIG_SYS_MONITOR_BASE
+#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE    /* start of monitor */
 #endif
 
 /*
@@ -177,8 +194,6 @@
 /*
  * The reserved memory
  */
-#define CONFIG_SYS_MONITOR_BASE        CONFIG_SYS_TEXT_BASE /* start of monitor */
-
 #define CONFIG_SYS_MONITOR_LEN         (384 * 1024) /* Reserve 384 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN          (512 * 1024) /* Reserved for malloc */
 
@@ -187,9 +202,8 @@
  */
 #define CONFIG_SYS_INIT_RAM_LOCK       1
 #define CONFIG_SYS_INIT_RAM_ADDR       0xE6000000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_END        0x1000 /* End of used area in RAM */
-#define CONFIG_SYS_GBL_DATA_SIZE       0x100 /* num bytes initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_SIZE       0x1000 /* Size of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_OFFSET     (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 
 /*
  * Local Bus Configuration & Clock Setup
@@ -604,14 +618,6 @@
 #define CONFIG_SYS_DBAT7L      CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U      CONFIG_SYS_IBAT7U
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD  0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM  0x02 /* Software reboot */
-
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE   230400  /* speed of kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX  2       /* which serial port to use */