rename CFG_ENV macros to CONFIG_ENV

[karo-tx-uboot.git] / include / configs / MPC8568MDS.h

diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index 9e6bb44ff925f93a529b6c4d9acc531858a22d8a..80697a5ce31c74c78779ddda2e1c9c1404372451 100644 (file)
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -41,14 +41,6 @@
 #define CONFIG_TSEC_ENET               /* tsec ethernet support */
 #define CONFIG_QE                      /* Enable QE */
 #define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL                 /* possible DLL fix needed */
-/*#define CONFIG_DDR_2T_TIMING          Sets the 2T timing bit */
-
-/*#define CONFIG_DDR_ECC*/                     /* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/  /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE          0xDeadBeef
-
 #define CONFIG_FSL_LAW         1       /* Use common FSL init code */
 
 /*
@@ -58,8 +50,6 @@
  */
 #define CONFIG_ASSUME_AMD_FLASH
 
-#define MPC85xx_DDR_SDRAM_CLK_CNTL     /* 85xx has clock control reg */
-
 #ifndef __ASSEMBLY__
 extern unsigned long get_clock_freq(void);
 #endif                                           /*Replace a call to get_clock_freq (after it is implemented)*/
@@ -95,24 +85,33 @@ extern unsigned long get_clock_freq(void);
 #define CFG_PCI1_ADDR           (CFG_CCSRBAR+0x8000)
 #define CFG_PCIE1_ADDR          (CFG_CCSRBAR+0xa000)
 
-/*
- * DDR Setup
- */
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM              /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL                 /* possible DLL fix needed */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
+
+#define CONFIG_MEM_INIT_VALUE  0xDeadBeef
+
 #define CFG_DDR_SDRAM_BASE     0x00000000      /* DDR is system memory*/
 #define CFG_SDRAM_BASE         CFG_DDR_SDRAM_BASE
 
-#define SPD_EEPROM_ADDRESS     0x51            /* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS     1
+#define CONFIG_DIMM_SLOTS_PER_CTLR     1
+#define CONFIG_CHIP_SELECTS_PER_CTRL   (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
-/*
- * Make sure required options are set
- */
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS     0x51    /* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
 #ifndef CONFIG_SPD_EEPROM
 #error ("CONFIG_SPD_EEPROM is required")
 #endif
 
 #undef CONFIG_CLOCKS_IN_MHZ
 
-
 /*
  * Local Bus Definitions
  */
@@ -167,7 +166,7 @@ extern unsigned long get_clock_freq(void);
 
 #define CFG_MONITOR_BASE       TEXT_BASE       /* start of monitor */
 
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
 #define CFG_FLASH_CFI
 #define CFG_FLASH_EMPTY_INFO
 
@@ -302,6 +301,9 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_BOARD_SETUP          1
 #define CONFIG_OF_STDOUT_VIA_ALIAS     1
 
+#define CFG_64BIT_VSPRINTF     1
+#define CFG_64BIT_STRTOUL      1
+
 /*
  * I2C
  */
@@ -422,10 +424,10 @@ extern unsigned long get_clock_freq(void);
 /*
  * Environment
  */
-#define CFG_ENV_IS_IN_FLASH    1
-#define CFG_ENV_ADDR           (CFG_MONITOR_BASE + 0x40000)
-#define CFG_ENV_SECT_SIZE      0x40000 /* 256K(one sector) for env */
-#define CFG_ENV_SIZE           0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR                (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_SECT_SIZE   0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SIZE                0x2000
 
 #define CONFIG_LOADS_ECHO      1       /* echo on for serial download */
 #define CFG_LOADS_BAUD_CHANGE  1       /* allow baudrate change */