#define CONFIG_MPC8568 1 /* MPC8568 specific */
#define CONFIG_MPC8568MDS 1 /* MPC8568MDS board specific */
-#define CONFIG_PCI
-#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI1 1 /* PCI controller */
+#define CONFIG_PCIE1 1 /* PCIE controller */
+#define CONFIG_FSL_PCI_INIT 1 /* use common fsl pci init code */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
#define CONFIG_QE /* Enable QE */
#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
-#define CONFIG_DDR_DLL /* possible DLL fix needed */
-/*#define CONFIG_DDR_2T_TIMING Sets the 2T timing bit */
-
-/*#define CONFIG_DDR_ECC*/ /* only for ECC DDR module */
-/*#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER*/ /* DDR controller or DMA? */
-#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
-
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
/*
* When initializing flash, if we cannot find the manufacturer ID,
*/
#define CONFIG_ASSUME_AMD_FLASH
-#define MPC85xx_DDR_SDRAM_CLK_CNTL /* 85xx has clock control reg */
-
#ifndef __ASSEMBLY__
extern unsigned long get_clock_freq(void);
#endif /*Replace a call to get_clock_freq (after it is implemented)*/
/*
* These can be toggled for performance analysis, otherwise use default.
*/
-#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
#define CONFIG_BTB /* toggle branch predition */
#define CONFIG_ADDR_STREAMING /* toggle addr streaming */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
-#undef CFG_DRAM_TEST /* memory test, takes time */
#define CFG_MEMTEST_START 0x00200000 /* memtest works on */
#define CFG_MEMTEST_END 0x00400000
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
-#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
+#define CFG_CCSRBAR_PHYS CFG_CCSRBAR /* physical addr of CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
-/*
- * DDR Setup
- */
+#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
+#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
+
+/* DDR Setup */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup*/
+#define CONFIG_DDR_SPD
+#define CONFIG_DDR_DLL /* possible DLL fix needed */
+#undef CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
+
+#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
+
#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
-#define SPD_EEPROM_ADDRESS 0x51 /* DDR DIMM */
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-/*
- * Make sure required options are set
- */
+/* I2C addresses of SPD EEPROMs */
+#define SPD_EEPROM_ADDRESS 0x51 /* CTLR 0 DIMM 0 */
+
+/* Make sure required options are set */
#ifndef CONFIG_SPD_EEPROM
#error ("CONFIG_SPD_EEPROM is required")
#endif
#undef CONFIG_CLOCKS_IN_MHZ
-
/*
* Local Bus Definitions
*/
#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
-#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
+#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
-#define CFG_FLASH_CFI_DRIVER
+#define CONFIG_FLASH_CFI_DRIVER
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#define CFG_BR2_PRELIM 0xf0001861
#define CFG_OR2_PRELIM 0xfc006901
-#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
-#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
-#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
-#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
+#define CFG_LBC_LCRR 0x00030004 /* LB clock ratio reg */
+#define CFG_LBC_LBCR 0x00000000 /* LB config reg */
+#define CFG_LBC_LSRT 0x20000000 /* LB sdram refresh timer */
+#define CFG_LBC_MRTPR 0x00000000 /* LB refresh timer prescal*/
/*
* LSDMR masks
#define CFG_OR5_PRELIM 0xffff69f7
#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK 1
+#define CFG_INIT_RAM_LOCK 1
#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
-#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
+#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
-#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (128 * 1024) /* Reserved for malloc */
/* Serial Port */
#define CONFIG_CONS_INDEX 1
#endif
/* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE 1
-#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
-#define OF_CPU "PowerPC,8568@0"
-#define OF_SOC "soc8568@e0000000"
-#define OF_QE "qe@e0080000"
-#define OF_TBCLK (bd->bi_busfreq / 8)
-#define OF_STDOUT_PATH "/soc8568@e0000000/serial@4500"
+#define CFG_64BIT_VSPRINTF 1
+#define CFG_64BIT_STRTOUL 1
/*
* I2C
#define CFG_PCI1_IO_PHYS 0xe2000000
#define CFG_PCI1_IO_SIZE 0x00800000 /* 8M */
-#define CFG_PEX_MEM_BASE 0xa0000000
-#define CFG_PEX_MEM_PHYS CFG_PEX_MEM_BASE
-#define CFG_PEX_MEM_SIZE 0x10000000 /* 256M */
-#define CFG_PEX_IO_BASE 0x00000000
-#define CFG_PEX_IO_PHYS 0xe2800000
-#define CFG_PEX_IO_SIZE 0x00800000 /* 8M */
+#define CFG_PCIE1_MEM_BASE 0xa0000000
+#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
+#define CFG_PCIE1_MEM_SIZE 0x20000000 /* 512M */
+#define CFG_PCIE1_IO_BASE 0x00000000
+#define CFG_PCIE1_IO_PHYS 0xe2800000
+#define CFG_PCIE1_IO_SIZE 0x00800000 /* 8M */
#define CFG_SRIO_MEM_BASE 0xc0000000
#define CONFIG_eTSEC_MDIO_BUS
#ifdef CONFIG_eTSEC_MDIO_BUS
-#define CONFIG_MIIM_ADDRESS 0xE0024520
+#define CONFIG_MIIM_ADDRESS 0xE0024520
#endif
#define CONFIG_UEC_ETH1 /* GETH1 */
#if defined(CONFIG_PCI)
#define CONFIG_NET_MULTI
-#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
#undef CONFIG_EEPRO100
#undef CONFIG_TULIP
#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CFG_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS 0x00000000
+#define CFG_PCI_MEMORY_PHYS 0x00000000
+#define CFG_PCI_MEMORY_SIZE 0x80000000
+
#endif /* CONFIG_PCI */
#ifndef CONFIG_NET_MULTI
-#define CONFIG_NET_MULTI 1
+#define CONFIG_NET_MULTI 1
#endif
#if defined(CONFIG_TSEC_ENET)
/*
* Environment
*/
-#define CFG_ENV_IS_IN_FLASH 1
-#define CFG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
-#define CFG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
-#define CFG_ENV_SIZE 0x2000
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE + 0x40000)
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K(one sector) for env */
+#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_CMD_PING
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
#if defined(CONFIG_PCI)
#define CONFIG_CMD_PCI
* Miscellaneous configurable options
*/
#define CFG_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
#define CFG_LOAD_ADDR 0x2000000 /* default load address */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
-
-/* Cache Configuration */
-#define CFG_DCACHE_SIZE 32768
-#define CFG_CACHELINE_SIZE 32
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT 5 /*log base 2 of the above value*/
-#endif
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
/*
* Internal Definitions
projects / karo-tx-uboot.git / blobdiff