*
* Configuration settings for the AcTux-2 board.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define CONFIG_IXP425 1
#define CONFIG_ACTUX2 1
+#define CONFIG_MACH_TYPE 1480
+
#define CONFIG_DISPLAY_CPUINFO 1
#define CONFIG_DISPLAY_BOARDINFO 1
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 5
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F 1
+#define CONFIG_SYS_LDSCRIPT "board/actux2/u-boot.lds"
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
-#undef CONFIG_USE_IRQ
-
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
#if defined(CONFIG_CMD_KGDB)
# define CONFIG_KGDB_BAUDRATE 230400
-/* which serial port to use */
-# define CONFIG_KGDB_SER_INDEX 1
#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
-#define CONFIG_SYS_PROMPT "=> "
/* Console I/O Buffer Size */
#define CONFIG_SYS_CBSIZE 256
/* Print Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ 3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66666666
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
115200, 230400 }
#define CONFIG_SERIAL_RTS_ACTIVE 1
-/*
- * Stack sizes
- * The stack sizes are set up in start.S using the settings below
- */
-#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
-
/* Expansion bus settings */
#define CONFIG_SYS_EXP_CS0 0xbd113042
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
-#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* 16MB SDRAM */
#define CONFIG_SYS_SDR_CONFIG 0x3A
#define CONFIG_SYS_DRAM_SIZE 0x01000000
/* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE 0x50000000
#define CONFIG_SYS_MAX_FLASH_BANKS 1
/* max number of sectors on one chip */
#define CONFIG_SYS_MAX_FLASH_SECT 140
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT 262144
/* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI
/* include IXP4xx NPE support */
#define CONFIG_IXP4XX_NPE 1
-#define CONFIG_NET_MULTI 1
/* NPE0 PHY address */
#define CONFIG_PHY_ADDR 0x00
/* MII PHY management */
#define CONFIG_MII 1
+/* fixed-speed switch without standard PHY registers on MII */
+#define CONFIG_MII_NPE0_FIXEDLINK 1
+#define CONFIG_MII_NPE0_SPEED 100
+#define CONFIG_MII_NPE0_FULLDUPLEX 1
+
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
#define CONFIG_RESET_PHY_R 1
"npe_ucode=50040000\0" \
"mtd=IXP4XX-Flash.0:256k(uboot),64k(ucode),1152k(linux),-(root)\0" \
"kerneladdr=50050000\0" \
+ "kernelfile=actux2/uImage\0" \
+ "rootfile=actux2/rootfs\0" \
"rootaddr=50170000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
- " tftp ${loadaddr} u-boot.bin;" \
+ " tftp ${loadaddr} actux2/u-boot.bin;" \
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 50003fff;" \
" protect off 50006000 5003ffff;" \
" erase 50006000 5003ffff\0" \
"writeboot=cp.b 10000 50000000 4000;" \
" cp.b 16000 50006000 3a000\0" \
- "eraseenv=protect off 50004000 50005fff;" \
- " erase 50004000 50005fff\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */