* (C) Copyright 2006-2008
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
- * SPDX-License-Identifier: GPL-2.0+
+ * SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define CONFIG_ALPR 1 /* Board is ebony */
#define CONFIG_440GX 1 /* Specifc GX support */
#define CONFIG_440 1 /* ... PPC440 family */
-#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
#define CONFIG_LAST_STAGE_INIT 1 /* call last_stage_init() */
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
-#undef CONFIG_SOFT_I2C /* I2C bit-banged */
-#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
-#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_NOPROBES {0x69} /* Don't probe these addrs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_PPC4XX
+#define CONFIG_SYS_I2C_PPC4XX_CH0
+#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
+#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
+#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
/*-----------------------------------------------------------------------
* I2C EEPROM (PCF8594C)
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
- "bootm\0" \
+ "bootm\0" \
"net_nfs_fdt=tftp 200000 ${bootfile};" \
"tftp ${fdt_addr} ${fdt_file};" \
"run nfsargs addip addtty;" \
/*
* Command line configuration.
*/
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_FPGA
+#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMD_I2C
-#undef CONFIG_CMD_LOADB
-#undef CONFIG_CMD_LOADS
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#undef CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#undef CONFIG_WATCHDOG /* watchdog disabled */
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
-
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2, \
CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
#define CONFIG_SYS_NAND_QUIET_TEST 1 /* don't warn upon unknown NAND flash */
+#define CONFIG_SYS_NAND_MAX_OOBFREE 2
+#define CONFIG_SYS_NAND_MAX_ECCPOS 56
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
/* pass open firmware flat tree */