#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_15 | B1RAT_15 | B1HT_3 | B1RDYPOL | B0WAT_15 | B0RAT_15 | B0HT_3 | B0RDYPOL)
#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_15 | B3RAT_15 | B3HT_3 | B3RDYPOL | B2WAT_15 | B2RAT_15 | B2HT_3 | B2RDYPOL)
-#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (512 * 1024)
* (can't be used same time as ethernet)
*/
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_NAND)
-#define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC
+# define CONFIG_BFIN_NFC_BOOTROM_ECC
#endif
#ifdef CONFIG_BFIN_NFC
#define CONFIG_BFIN_NFC_CTL_VAL 0x0033
#define CONFIG_DRIVER_NAND_BFIN
#define CONFIG_SYS_NAND_BASE 0 /* not actually used */
#define CONFIG_SYS_MAX_NAND_DEVICE 1
-#define NAND_MAX_CHIPS 1
#define CONFIG_CMD_NAND
#endif
#define CONFIG_BFIN_MAC
#define CONFIG_RMII
#define CONFIG_NETCONSOLE 1
-#define CONFIG_NET_MULTI 1
#endif
#define CONFIG_HOSTNAME bf526-ezbrd
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-
/*
* Flash Settings
#define CONFIG_BFIN_SPI
#define CONFIG_ENV_SPI_MAX_HZ 30000000
#define CONFIG_SF_DEFAULT_SPEED 30000000
-#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_SST
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_ENV_SECT_SIZE 0x2000
#endif
-#define ENV_IS_EMBEDDED_CUSTOM
+#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
-#define CONFIG_BFIN_TWI_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_ADI
/*
*/
#if !defined(__ADSPBF522__) && !defined(__ADSPBF523__)
#define CONFIG_USB
-#define CONFIG_MUSB_HCD
+#define CONFIG_USB_MUSB_HCD
#define CONFIG_USB_BLACKFIN
#define CONFIG_USB_STORAGE
-#define CONFIG_MUSB_TIMEOUT 100000
+#define CONFIG_USB_MUSB_TIMEOUT 100000
#endif
/* define to enable run status via led */
/* #define CONFIG_STATUS_LED */
#ifdef CONFIG_STATUS_LED
+#define CONFIG_GPIO_LED
#define CONFIG_BOARD_SPECIFIC_LED
-#ifndef __ASSEMBLY__
-typedef unsigned int led_id_t;
-void __led_init(led_id_t mask, int state);
-void __led_set(led_id_t mask, int state);
-void __led_toggle(led_id_t mask);
-#endif
/* use LED0 to indicate booting/alive */
#define STATUS_LED_BOOT 0
-#define STATUS_LED_BIT 1
+#define STATUS_LED_BIT GPIO_PF8
#define STATUS_LED_STATE STATUS_LED_ON
#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 4)
/* use LED1 to indicate crash */
#define STATUS_LED_CRASH 1
-#define STATUS_LED_BIT1 2
+#define STATUS_LED_BIT1 GPIO_PG11
#define STATUS_LED_STATE1 STATUS_LED_ON
#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
+/* #define STATUS_LED_BIT2 GPIO_PG12 */
#endif