#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3)
#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_7 | B3RAT_11 | B3HT_2 | B3ST_3 | B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3)
-#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
*/
#ifndef __ADSPBF534__
#define ADI_CMDS_NETWORK 1
-#define CONFIG_NET_MULTI
-/* The next 3 lines are for use with SMSC on EXT-BF5xx-USB-ETH2 */
-#define CONFIG_SMC911X 1
-#define CONFIG_SMC911X_BASE 0x24000000
+#define CONFIG_SMC911X 1
+#define CONFIG_SMC911X_BASE 0x20308000
#define CONFIG_SMC911X_16_BIT
+#define CONFIG_NETCONSOLE 1
#endif
#define CONFIG_HOSTNAME cm-bf537u
-/* Uncomment next line to use fixed MAC address */
-/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
-
/*
* Flash Settings
#define CONFIG_SYS_MAX_FLASH_SECT 35
+/*
+ * SPI Settings
+ */
+#define CONFIG_BFIN_SPI
+#define CONFIG_ENV_SPI_MAX_HZ 30000000
+
+
/*
* Env Storage Settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
-#define CONFIG_ENV_OFFSET 0x4000
-#define CONFIG_ENV_SIZE 0x2000
-#define CONFIG_ENV_SECT_SIZE 0x20000
+#define CONFIG_ENV_OFFSET 0x8000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
+#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_SECT_SIZE 0x8000
#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
#define ENV_IS_EMBEDDED
-#else
-#define ENV_IS_EMBEDDED_CUSTOM
#endif
#ifdef ENV_IS_EMBEDDED
/* WARNING - the following is hand-optimized to fit within
* it linked after the configuration sector.
*/
# define LDS_BOARD_TEXT \
- cpu/blackfin/traps.o (.text .text.*); \
- cpu/blackfin/interrupt.o (.text .text.*); \
- cpu/blackfin/serial.o (.text .text.*); \
- common/dlmalloc.o (.text .text.*); \
- lib_generic/crc32.o (.text .text.*); \
+ arch/blackfin/lib/built-in.o (.text*); \
+ arch/blackfin/cpu/built-in.o (.text*); \
. = DEFINED(env_offset) ? env_offset : .; \
- common/env_embedded.o (.text .text.*);
+ common/env_embedded.o (.text*);
#endif
/*
* I2C Settings
*/
-#define CONFIG_BFIN_TWI_I2C 1
-#define CONFIG_HARD_I2C 1
-#define CONFIG_SYS_I2C_SPEED 50000
-#define CONFIG_SYS_I2C_SLAVE 0
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_ADI
+/*
+ * SPI_MMC Settings
+ */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_MMC_SPI
+
/*
* Misc Settings
*/
#define CONFIG_MISC_INIT_R
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 0
-
+#define CONFIG_BOOTCOMMAND "run flashboot"
+#define FLASHBOOT_ENV_SETTINGS \
+ "flashboot=flread 20040000 1000000 300000;" \
+ "bootm 0x1000000\0"
+#define CONFIG_BOARD_SIZE_LIMIT $$((384 * 1024))
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
-#undef CONFIG_BOOTCOMMAND
-#define CONFIG_BOOTCOMMAND "run flashboot"
-
-#undef CONFIG_EXTRA_ENV_SETTINGS
-#define CONFIG_EXTRA_ENV_SETTINGS \
- NAND_ENV_SETTINGS \
- NETWORK_ENV_SETTINGS \
- "flashboot=flread 20040000 1000000 280000; bootm 0x1000000\0"
-
#endif