siemens, draco: add new target

[karo-tx-uboot.git] / include / configs / draco.h

diff --git a/include/configs/draco.h b/include/configs/draco.h
new file mode 100644 (file)
index 0000000..a2438d8
--- /dev/null
+++ b/include/configs/draco.h
@@ -0,0 +1,92 @@
+/*
+ * (C) Copyright 2013 Siemens Schweiz AG
+ * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * U-Boot file:/include/configs/am335x_evm.h
+ *
+ * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#ifndef __CONFIG_DRACO_H
+#define __CONFIG_DRACO_H
+
+#define CONFIG_SIEMENS_DRACO
+#define MACH_TYPE_DRACO                        4314
+#define CONFIG_SIEMENS_MACH_TYPE       MACH_TYPE_DRACO
+
+#include "siemens-am33x-common.h"
+
+#define CONFIG_SYS_MPUCLK      275
+#define DDR_PLL_FREQ   303
+#undef CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC
+
+#define BOARD_DFU_BUTTON_GPIO  27
+#define BOARD_DFU_BUTTON_LED   64      /* red LED */
+#define BOARD_STATUS_LED       103     /* green LED */
+#define GPIO_LAN9303_NRST      88      /* GPIO2_24 = gpio88 */
+
+#undef CONFIG_DOS_PARTITION
+#undef CONFIG_CMD_FAT
+
+
+ /* Physical Memory Map */
+#define CONFIG_MAX_RAM_BANK_SIZE       (1024 << 20)    /* 1GB */
+
+/* I2C Configuration */
+#define CONFIG_SYS_I2C_SPEED           100000
+
+#define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
+#define EEPROM_ADDR_DDR3 0x90
+#define EEPROM_ADDR_CHIP 0x120
+
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS     0x300
+
+#undef CONFIG_SPL_NET_SUPPORT
+#undef CONFIG_SPL_NET_VCI_STRING
+#undef CONFIG_SPL_ETH_SUPPORT
+
+#undef CONFIG_MII
+#undef CONFIG_PHY_GIGE
+#define CONFIG_PHY_SMSC
+
+#define CONFIG_FACTORYSET
+
+/* Watchdog */
+#define CONFIG_OMAP_WATCHDOG
+
+#ifndef CONFIG_SPL_BUILD
+
+/* Default env settings */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+       "nand_img_size=0x400000\0" \
+       "optargs=\0" \
+       CONFIG_COMMON_ENV_SETTINGS
+
+#ifndef CONFIG_RESTORE_FLASH
+/* set to negative value for no autoboot */
+#define CONFIG_BOOTDELAY               3
+
+#define CONFIG_BOOTCOMMAND \
+"if dfubutton; then " \
+       "run dfu_start; " \
+       "reset; " \
+"fi;" \
+"run nand_boot;" \
+"reset;"
+
+
+#else
+#define CONFIG_BOOTDELAY               0
+
+#define CONFIG_BOOTCOMMAND                     \
+       "setenv autoload no; "                  \
+       "dhcp; "                                \
+       "if tftp 80000000 debrick.scr; then "   \
+               "source 80000000; "             \
+       "fi"
+#endif
+#endif /* CONFIG_SPL_BUILD */
+#endif /* ! __CONFIG_DRACO_H */