arm/km: fix u-boot.kwb build breakage

[karo-tx-uboot.git] / include / configs / km / km_arm.h

diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 20ee6eab85694e3ab19fd75c95134a03c047c6e9..4741278606741123213ffaf6011684a3c3951b9a 100644 (file)
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -40,7 +40,6 @@
  * High Level Configuration Options (easy to change)
  */
 #define CONFIG_MARVELL
-#define CONFIG_ARM926EJS               /* Basic Architecture */
 #define CONFIG_FEROCEON_88FR131                /* CPU Core subversion */
 #define CONFIG_KIRKWOOD                        /* SOC Family Name */
 #define CONFIG_KW88F6281               /* SOC Name */
@@ -49,6 +48,12 @@
 /* include common defines/options for all Keymile boards */
 #include "keymile-common.h"
 
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_SF
+#define CONFIG_SOFT_I2C                /* I2C bit-banged       */
+
+#include "asm/arch/config.h"
+
 #define CONFIG_SYS_TEXT_BASE   0x04000000      /* code address after reloc */
 #define CONFIG_ENV_SIZE                (128 << 10)     /* NAND chip block size */
 #define CONFIG_SYS_MEMTEST_START 0x00400000    /* 4M */
@@ -75,12 +80,7 @@
 
 #define CONFIG_KM_ARCH_DBG_FILE                "scripts/debug-arm-env.txt"
 
-#define CONFIG_MD5     /* get_random_hex on krikwood needs MD5 support */
 #define CONFIG_SKIP_LOWLEVEL_INIT      /* disable board lowlevel_init */
-#define CONFIG_KIRKWOOD_EGIGA_INIT     /* Enable GbePort0/1 for kernel */
-#undef  CONFIG_KIRKWOOD_PCIE_INIT      /* Disable PCIE Port0 for kernel */
-#define CONFIG_KIRKWOOD_RGMII_PAD_1V8  /* Set RGMII Pad voltage to 1.8V */
-
 #define CONFIG_MISC_INIT_R
 
 /*
@@ -116,7 +116,6 @@
  */
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_MTDPARTS
-#define CONFIG_CMD_NAND
 #define CONFIG_CMD_NFS
 
 /*
@@ -131,8 +130,6 @@
  */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define NAND_MAX_CHIPS                 1
-#define CONFIG_NAND_KIRKWOOD
-#define CONFIG_SYS_NAND_BASE           0xd8000000
 
 #define BOOTFLASH_START                0x0
 
@@ -175,8 +172,6 @@
 /*
  * I2C related stuff
  */
-#define        CONFIG_SOFT_I2C         /* I2C bit-banged       */
-
 #define        CONFIG_KIRKWOOD_GPIO            /* Enable GPIO Support */
 #if defined(CONFIG_SOFT_I2C)
 #ifndef __ASSEMBLY__
@@ -200,8 +195,6 @@ int get_scl(void);
 #define I2C_DELAY      udelay(3)       /* 1/4 I2C clock duration */
 #define I2C_SOFT_DECLARATIONS
 
-#define        CONFIG_SYS_I2C_SLAVE            0x0
-#define        CONFIG_SYS_I2C_SPEED            100000
 #endif
 
 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x50
@@ -224,15 +217,8 @@ int get_scl(void);
 #define CONFIG_ENV_OFFSET_REDUND       0x2000 /* no bracets! */
 #define CONFIG_ENV_SIZE_REDUND         (CONFIG_ENV_SIZE)
 
-#define CONFIG_CMD_SF
-
 #define CONFIG_SPI_FLASH
-#define CONFIG_HARD_SPI
-#define CONFIG_KIRKWOOD_SPI
 #define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_ENV_SPI_BUS             0
-#define CONFIG_ENV_SPI_CS              0
-#define CONFIG_ENV_SPI_MAX_HZ          50000000        /* 50Mhz */
 
 #define FLASH_GPIO_PIN                 0x00010000
 
@@ -272,8 +258,6 @@ int get_scl(void);
 
 /* additions for new relocation code, must be added to all boards */
 #define CONFIG_SYS_SDRAM_BASE          0x00000000
-/* Kirkwood has 2k of Security SRAM, use it for SP */
-#define CONFIG_SYS_INIT_SP_ADDR                0xC8012000
 /* Do early setups now in board_init_f() */
 #define CONFIG_BOARD_EARLY_INIT_F