/*
- * (C) Copyright 2001
+ * (C) Copyright 2001-2005
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
#define CONFIG_MPC823 1 /* This is a MPC823E CPU */
#define CONFIG_LWMON 1 /* ...on a LWMON board */
-#define CONFIG_BOARD_PRE_INIT 1 /* Call board_pre_init */
+/* Default Ethernet MAC address */
+#define CONFIG_ETHADDR 00:11:B0:00:00:00
+
+/* The default Ethernet MAC address can be overwritten just once */
+#ifdef CONFIG_ETHADDR
+#define CONFIG_OVERWRITE_ETHADDR_ONCE 1
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */
#define CONFIG_LCD 1 /* use LCD controller ... */
#define CONFIG_HLD1045 1 /* ... with a HLD1045 display */
+#define CONFIG_LCD_LOGO 1 /* print our logo on the LCD */
+#define CONFIG_LCD_INFO 1 /* ... and some board info */
#define CONFIG_SPLASH_SCREEN /* ... with splashscreen support*/
-#if 1
+#define CONFIG_SERIAL_MULTI 1
#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
-#else
-#define CONFIG_8xx_CONS_SCC2
-#endif
+#define CONFIG_8xx_CONS_SCC2 1 /* Console is on SCC2 */
#define CONFIG_BAUDRATE 115200 /* with watchdog >= 38400 needed */
CFG_POST_SPR | \
CFG_POST_SYSMON)
-#define CONFIG_BOOTCOMMAND "run flash_self"
+/*
+ * Keyboard commands:
+ * # = 0x28 = ENTER : enable bootmessages on LCD
+ * 2 = 0x3A+0x3C = F1 + F3 : enable update mode
+ * 3 = 0x3C+0x3F = F3 + F6 : enable test mode
+ */
+
+#define CONFIG_BOOTCOMMAND "autoscr 40040000;saveenv"
+/* "gatewayip=10.8.211.250\0" \ */
#define CONFIG_EXTRA_ENV_SETTINGS \
"kernel_addr=40080000\0" \
"ramdisk_addr=40280000\0" \
- "magic_keys=#3\0" \
+ "netmask=255.255.192.0\0" \
+ "serverip=10.8.2.101\0" \
+ "ipaddr=10.8.57.0\0" \
+ "magic_keys=#23\0" \
"key_magic#=28\0" \
"key_cmd#=setenv addfb setenv 'bootargs $bootargs console=tty0'\0" \
+ "key_magic2=3A+3C\0" \
+ "key_cmd2=echo *** Entering Update Mode ***;" \
+ "if fatload ide 0:3 10000 update.scr;" \
+ "then autoscr 10000;" \
+ "else echo *** UPDATE FAILED ***;" \
+ "fi\0" \
"key_magic3=3C+3F\0" \
"key_cmd3=echo *** Entering Test Mode ***;" \
"setenv add_misc 'setenv bootargs $bootargs testmode'\0" \
#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#define CONFIG_WATCHDOG 1 /* watchdog enabled */
+#define CFG_WATCHDOG_FREQ (CFG_HZ / 20)
#undef CONFIG_STATUS_LED /* Status LED disabled */
#define CFG_CMD_POST_DIAG 0
#endif
-#ifdef CONFIG_8xx_CONS_SCC2 /* Can't use ethernet, then */
-#define CONFIG_COMMANDS ( (CONFIG_CMD_DFL & ~CFG_CMD_NET) | \
- CFG_CMD_DATE | \
- CFG_CMD_I2C | \
- CFG_CMD_EEPROM | \
- CFG_CMD_IDE | \
- CFG_CMD_BSP | \
- CFG_CMD_BMP | \
- CFG_CMD_POST_DIAG )
-#else
#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
- CFG_CMD_DHCP | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_BMP | \
+ CFG_CMD_BSP | \
CFG_CMD_DATE | \
- CFG_CMD_I2C | \
+ CFG_CMD_DHCP | \
CFG_CMD_EEPROM | \
+ CFG_CMD_FAT | \
+ CFG_CMD_I2C | \
CFG_CMD_IDE | \
- CFG_CMD_BSP | \
- CFG_CMD_BMP | \
- CFG_CMD_POST_DIAG )
-#endif
+ CFG_CMD_NFS | \
+ CFG_CMD_POST_DIAG | \
+ CFG_CMD_SNTP )
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
#define CFG_HUSH_PARSER 1 /* use "hush" command parser */
-#endif
#ifdef CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
+#endif
#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#endif
+/*----------------------------------------------------------------------*/
+#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */
+#undef CONFIG_MODEM_SUPPORT_DEBUG
+
+#define CONFIG_MODEM_KEY_MAGIC "3C+3D" /* press F3 + F4 keys to enable modem */
+#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */
+#if 0
+#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */
+#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */
+#endif
+/*----------------------------------------------------------------------*/
+
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
#define CFG_FLASH_ERASE_TOUT 180000 /* Timeout for Flash Erase (in ms) */
#define CFG_FLASH_WRITE_TOUT 600 /* Timeout for Flash Write (in ms) */
+#define CFG_FLASH_USE_BUFFER_WRITE
+#define CFG_FLASH_BUFFER_WRITE_TOUT 2048 /* Timeout for Flash Buffer Write (in ms) */
+/* Buffer size.
+ We have two flash devices connected in parallel.
+ Each device incorporates a Write Buffer of 32 bytes.
+ */
+#define CFG_FLASH_BUFFER_SIZE (2*32)
-#if 1
-/* Put environment in flash which is much faster to boot */
+/* Put environment in flash which is much faster to boot than using the EEPROM */
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_ADDR 0x40040000 /* Address of Environment Sector */
#define CFG_ENV_SIZE 0x2000 /* Total Size of Environment */
#define CFG_ENV_SECT_SIZE 0x40000 /* we have BIG sectors only :-( */
-#else
-/* Environment in EEPROM */
-#define CFG_ENV_IS_IN_EEPROM 1
-#define CFG_ENV_OFFSET 0
-#define CFG_ENV_SIZE 2048
-#endif
+
/*-----------------------------------------------------------------------
* I2C/EEPROM Configuration
*/
/* Offset for alternate registers */
#define CFG_ATA_ALT_OFFSET 0x0100
+#define CONFIG_SUPPORT_VFAT /* enable VFAT support */
+
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
-/*#define CFG_DER 0x2002000F*/
#define CFG_DER 0
/*
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CONFIG_MODEM_SUPPORT 1 /* enable modem initialization stuff */
-#undef CONFIG_MODEM_SUPPORT_DEBUG
-
-#define CONFIG_MODEM_KEY_MAGIC "3C+3F" /* hold down these keys to enable modem */
-
#endif /* __CONFIG_H */
projects / karo-tx-uboot.git / blobdiff