Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wirel...

[mv-sheeva.git] / include / net / mac80211.h

diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 23e46cee06f99353215a864c2a9ee324347671a8..837353bfcb20f5d7e984b8c3b2dcbacfcffe2c59 100644 (file)
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -147,6 +147,8 @@ struct ieee80211_low_level_stats {
  * @BSS_CHANGED_CQM: Connection quality monitor config changed
  * @BSS_CHANGED_IBSS: IBSS join status changed
  * @BSS_CHANGED_ARP_FILTER: Hardware ARP filter address list or state changed.
+ * @BSS_CHANGED_QOS: QoS for this association was enabled/disabled. Note
+ *     that it is only ever disabled for station mode.
  */
 enum ieee80211_bss_change {
        BSS_CHANGED_ASSOC               = 1<<0,
@@ -162,6 +164,7 @@ enum ieee80211_bss_change {
        BSS_CHANGED_CQM                 = 1<<10,
        BSS_CHANGED_IBSS                = 1<<11,
        BSS_CHANGED_ARP_FILTER          = 1<<12,
+       BSS_CHANGED_QOS                 = 1<<13,
 
        /* when adding here, make sure to change ieee80211_reconfig */
 };
@@ -217,6 +220,7 @@ enum ieee80211_bss_change {
  *     filter ARP queries based on the @arp_addr_list, if disabled, the
  *     hardware must not perform any ARP filtering. Note, that the filter will
  *     be enabled also in promiscuous mode.
+ * @qos: This is a QoS-enabled BSS.
  */
 struct ieee80211_bss_conf {
        const u8 *bssid;
@@ -240,6 +244,7 @@ struct ieee80211_bss_conf {
        __be32 arp_addr_list[IEEE80211_BSS_ARP_ADDR_LIST_LEN];
        u8 arp_addr_cnt;
        bool arp_filter_enabled;
+       bool qos;
 };
 
 /**
@@ -620,15 +625,11 @@ struct ieee80211_rx_status {
  *     may turn the device off as much as possible. Typically, this flag will
  *     be set when an interface is set UP but not associated or scanning, but
  *     it can also be unset in that case when monitor interfaces are active.
- * @IEEE80211_CONF_QOS: Enable 802.11e QoS also know as WMM (Wireless
- *      Multimedia). On some drivers (iwlwifi is one of know) we have
- *      to enable/disable QoS explicitly.
  */
 enum ieee80211_conf_flags {
        IEEE80211_CONF_MONITOR          = (1<<0),
        IEEE80211_CONF_PS               = (1<<1),
        IEEE80211_CONF_IDLE             = (1<<2),
-       IEEE80211_CONF_QOS              = (1<<3),
 };
 
 
@@ -643,7 +644,6 @@ enum ieee80211_conf_flags {
  * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed
  * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed
  * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed
- * @IEEE80211_CONF_CHANGE_QOS: Quality of service was enabled or disabled
  */
 enum ieee80211_conf_changed {
        IEEE80211_CONF_CHANGE_SMPS              = BIT(1),
@@ -654,7 +654,6 @@ enum ieee80211_conf_changed {
        IEEE80211_CONF_CHANGE_CHANNEL           = BIT(6),
        IEEE80211_CONF_CHANGE_RETRY_LIMITS      = BIT(7),
        IEEE80211_CONF_CHANGE_IDLE              = BIT(8),
-       IEEE80211_CONF_CHANGE_QOS               = BIT(9),
 };
 
 /**