* @IEEE80211_CHANCTX_CHANGE_WIDTH: The channel width changed
* @IEEE80211_CHANCTX_CHANGE_RX_CHAINS: The number of RX chains changed
* @IEEE80211_CHANCTX_CHANGE_RADAR: radar detection flag changed
+ * @IEEE80211_CHANCTX_CHANGE_CHANNEL: switched to another operating channel,
+ * this is used only with channel switching with CSA
*/
enum ieee80211_chanctx_change {
IEEE80211_CHANCTX_CHANGE_WIDTH = BIT(0),
IEEE80211_CHANCTX_CHANGE_RX_CHAINS = BIT(1),
IEEE80211_CHANCTX_CHANGE_RADAR = BIT(2),
+ IEEE80211_CHANCTX_CHANGE_CHANNEL = BIT(3),
};
/**
};
/**
- * enum mac80211_tx_control_flags - flags to describe transmission information/status
+ * enum mac80211_tx_info_flags - flags to describe transmission information/status
*
* These flags are used with the @flags member of &ieee80211_tx_info.
*
* Note: If you have to add new flags to the enumeration, then don't
* forget to update %IEEE80211_TX_TEMPORARY_FLAGS when necessary.
*/
-enum mac80211_tx_control_flags {
+enum mac80211_tx_info_flags {
IEEE80211_TX_CTL_REQ_TX_STATUS = BIT(0),
IEEE80211_TX_CTL_ASSIGN_SEQ = BIT(1),
IEEE80211_TX_CTL_NO_ACK = BIT(2),
#define IEEE80211_TX_CTL_STBC_SHIFT 23
+/**
+ * enum mac80211_tx_control_flags - flags to describe transmit control
+ *
+ * @IEEE80211_TX_CTRL_PORT_CTRL_PROTO: this frame is a port control
+ * protocol frame (e.g. EAP)
+ *
+ * These flags are used in tx_info->control.flags.
+ */
+enum mac80211_tx_control_flags {
+ IEEE80211_TX_CTRL_PORT_CTRL_PROTO = BIT(0),
+};
+
/*
* This definition is used as a mask to clear all temporary flags, which are
* set by the tx handlers for each transmission attempt by the mac80211 stack.
/* NB: vif can be NULL for injected frames */
struct ieee80211_vif *vif;
struct ieee80211_key_conf *hw_key;
- /* 8 bytes free */
+ u32 flags;
+ /* 4 bytes free */
} control;
struct {
struct ieee80211_tx_rate rates[IEEE80211_TX_MAX_RATES];
* @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
* is stored in the @ampdu_delimiter_crc field)
* @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
+ * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
+ * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = BIT(0),
RX_FLAG_80P80MHZ = BIT(24),
RX_FLAG_160MHZ = BIT(25),
RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
+ RX_FLAG_10MHZ = BIT(28),
+ RX_FLAG_5MHZ = BIT(29),
};
#define RX_FLAG_STBC_SHIFT 26
* @radar_enabled: whether radar detection is enabled
*
* @long_frame_max_tx_count: Maximum number of transmissions for a "long" frame
- * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
- * but actually means the number of transmissions not the number of retries
+ * (a frame not RTS protected), called "dot11LongRetryLimit" in 802.11,
+ * but actually means the number of transmissions not the number of retries
* @short_frame_max_tx_count: Maximum number of transmissions for a "short"
- * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
- * number of transmissions not the number of retries
+ * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the
+ * number of transmissions not the number of retries
*
* @smps_mode: spatial multiplexing powersave mode; note that
* %IEEE80211_SMPS_STATIC is used when the device is not
* @addr: address of this interface
* @p2p: indicates whether this AP or STA interface is a p2p
* interface, i.e. a GO or p2p-sta respectively
+ * @csa_active: marks whether a channel switch is going on
* @driver_flags: flags/capabilities the driver has for this interface,
* these need to be set (or cleared) when the interface is added
* or, if supported by the driver, the interface type is changed
* be off when it is %NULL there can still be races and packets could be
* processed after it switches back to %NULL.
* @debugfs_dir: debugfs dentry, can be used by drivers to create own per
- * interface debug files. Note that it will be NULL for the virtual
+ * interface debug files. Note that it will be NULL for the virtual
* monitor interface (if that is requested.)
* @drv_priv: data area for driver use, will always be aligned to
* sizeof(void *).
struct ieee80211_bss_conf bss_conf;
u8 addr[ETH_ALEN];
bool p2p;
+ bool csa_active;
u8 cab_queue;
u8 hw_queue[IEEE80211_NUM_ACS];
* the stack.
*
* @IEEE80211_HW_CONNECTION_MONITOR:
- * The hardware performs its own connection monitoring, including
- * periodic keep-alives to the AP and probing the AP on beacon loss.
- * When this flag is set, signaling beacon-loss will cause an immediate
- * change to disassociated state.
+ * The hardware performs its own connection monitoring, including
+ * periodic keep-alives to the AP and probing the AP on beacon loss.
+ * When this flag is set, signaling beacon-loss will cause an immediate
+ * change to disassociated state.
*
* @IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC:
* This device needs to get data from beacon before association (i.e.
* @channel_change_time: time (in microseconds) it takes to change channels.
*
* @max_signal: Maximum value for signal (rssi) in RX information, used
- * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
+ * only when @IEEE80211_HW_SIGNAL_UNSPEC or @IEEE80211_HW_SIGNAL_DB
*
* @max_listen_interval: max listen interval in units of beacon interval
- * that HW supports
+ * that HW supports
*
* @queues: number of available hardware transmit queues for
* data packets. WMM/QoS requires at least four, these
* The callback can sleep.
*
* @set_tsf: Set the TSF timer to the specified value in the firmware/hardware.
- * Currently, this is only used for IBSS mode debugging. Is not a
+ * Currently, this is only used for IBSS mode debugging. Is not a
* required function.
* The callback can sleep.
*
* in IEEE 802.11-2007 section 17.3.8.6 and modify ACK timeout
* accordingly. This callback is not required and may sleep.
*
- * @testmode_cmd: Implement a cfg80211 test mode command.
- * The callback can sleep.
+ * @testmode_cmd: Implement a cfg80211 test mode command. The passed @vif may
+ * be %NULL. The callback can sleep.
* @testmode_dump: Implement a cfg80211 test mode dump. The callback can sleep.
*
* @flush: Flush all pending frames from the hardware queue, making sure
* @ipv6_addr_change: IPv6 address assignment on the given interface changed.
* Currently, this is only called for managed or P2P client interfaces.
* This callback is optional; it must not sleep.
+ *
+ * @channel_switch_beacon: Starts a channel switch to a new channel.
+ * Beacons are modified to include CSA or ECSA IEs before calling this
+ * function. The corresponding count fields in these IEs must be
+ * decremented, and when they reach zero the driver must call
+ * ieee80211_csa_finish(). Drivers which use ieee80211_beacon_get()
+ * get the csa counter decremented by mac80211, but must check if it is
+ * zero using ieee80211_csa_is_complete() after the beacon has been
+ * transmitted and then call ieee80211_csa_finish().
+ *
*/
struct ieee80211_ops {
void (*tx)(struct ieee80211_hw *hw,
void (*rfkill_poll)(struct ieee80211_hw *hw);
void (*set_coverage_class)(struct ieee80211_hw *hw, u8 coverage_class);
#ifdef CONFIG_NL80211_TESTMODE
- int (*testmode_cmd)(struct ieee80211_hw *hw, void *data, int len);
+ int (*testmode_cmd)(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
+ void *data, int len);
int (*testmode_dump)(struct ieee80211_hw *hw, struct sk_buff *skb,
struct netlink_callback *cb,
void *data, int len);
struct ieee80211_vif *vif,
struct inet6_dev *idev);
#endif
+ void (*channel_switch_beacon)(struct ieee80211_hw *hw,
+ struct ieee80211_vif *vif,
+ struct cfg80211_chan_def *chandef);
};
/**
};
#ifdef CONFIG_MAC80211_LEDS
-extern char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
-extern char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
-extern char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
-extern char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
-extern char *__ieee80211_create_tpt_led_trigger(
- struct ieee80211_hw *hw, unsigned int flags,
- const struct ieee80211_tpt_blink *blink_table,
- unsigned int blink_table_len);
+char *__ieee80211_get_tx_led_name(struct ieee80211_hw *hw);
+char *__ieee80211_get_rx_led_name(struct ieee80211_hw *hw);
+char *__ieee80211_get_assoc_led_name(struct ieee80211_hw *hw);
+char *__ieee80211_get_radio_led_name(struct ieee80211_hw *hw);
+char *__ieee80211_create_tpt_led_trigger(struct ieee80211_hw *hw,
+ unsigned int flags,
+ const struct ieee80211_tpt_blink *blink_table,
+ unsigned int blink_table_len);
#endif
/**
* ieee80211_get_tx_led_name - get name of TX LED
return ieee80211_beacon_get_tim(hw, vif, NULL, NULL);
}
+/**
+ * ieee80211_csa_finish - notify mac80211 about channel switch
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * After a channel switch announcement was scheduled and the counter in this
+ * announcement hit zero, this function must be called by the driver to
+ * notify mac80211 that the channel can be changed.
+ */
+void ieee80211_csa_finish(struct ieee80211_vif *vif);
+
+/**
+ * ieee80211_csa_is_complete - find out if counters reached zero
+ * @vif: &struct ieee80211_vif pointer from the add_interface callback.
+ *
+ * This function returns whether the channel switch counters reached zero.
+ */
+bool ieee80211_csa_is_complete(struct ieee80211_vif *vif);
+
+
/**
* ieee80211_proberesp_get - retrieve a Probe Response template
* @hw: pointer obtained from ieee80211_alloc_hw().
void ieee80211_get_key_rx_seq(struct ieee80211_key_conf *keyconf,
int tid, struct ieee80211_key_seq *seq);
+/**
+ * ieee80211_set_key_tx_seq - set key TX sequence counter
+ *
+ * @keyconf: the parameter passed with the set key
+ * @seq: new sequence data
+ *
+ * This function allows a driver to set the current TX IV/PNs for the
+ * given key. This is useful when resuming from WoWLAN sleep and the
+ * device may have transmitted frames using the PTK, e.g. replies to
+ * ARP requests.
+ *
+ * Note that this function may only be called when no TX processing
+ * can be done concurrently.
+ */
+void ieee80211_set_key_tx_seq(struct ieee80211_key_conf *keyconf,
+ struct ieee80211_key_seq *seq);
+
+/**
+ * ieee80211_set_key_rx_seq - set key RX sequence counter
+ *
+ * @keyconf: the parameter passed with the set key
+ * @tid: The TID, or -1 for the management frame value (CCMP only);
+ * the value on TID 0 is also used for non-QoS frames. For
+ * CMAC, only TID 0 is valid.
+ * @seq: new sequence data
+ *
+ * This function allows a driver to set the current RX IV/PNs for the
+ * given key. This is useful when resuming from WoWLAN sleep and GTK
+ * rekey may have been done while suspended. It should not be called
+ * if IV checking is done by the device and not by mac80211.
+ *
+ * Note that this function may only be called when no RX processing
+ * can be done concurrently.
+ */
+void ieee80211_set_key_rx_seq(struct ieee80211_key_conf *keyconf,
+ int tid, struct ieee80211_key_seq *seq);
+
+/**
+ * ieee80211_remove_key - remove the given key
+ * @keyconf: the parameter passed with the set key
+ *
+ * Remove the given key. If the key was uploaded to the hardware at the
+ * time this function is called, it is not deleted in the hardware but
+ * instead assumed to have been removed already.
+ *
+ * Note that due to locking considerations this function can (currently)
+ * only be called during key iteration (ieee80211_iter_keys().)
+ */
+void ieee80211_remove_key(struct ieee80211_key_conf *keyconf);
+
+/**
+ * ieee80211_gtk_rekey_add - add a GTK key from rekeying during WoWLAN
+ * @vif: the virtual interface to add the key on
+ * @keyconf: new key data
+ *
+ * When GTK rekeying was done while the system was suspended, (a) new
+ * key(s) will be available. These will be needed by mac80211 for proper
+ * RX processing, so this function allows setting them.
+ *
+ * The function returns the newly allocated key structure, which will
+ * have similar contents to the passed key configuration but point to
+ * mac80211-owned memory. In case of errors, the function returns an
+ * ERR_PTR(), use IS_ERR() etc.
+ *
+ * Note that this function assumes the key isn't added to hardware
+ * acceleration, so no TX will be done with the key. Since it's a GTK
+ * on managed (station) networks, this is true anyway. If the driver
+ * calls this function from the resume callback and subsequently uses
+ * the return code 1 to reconfigure the device, this key will be part
+ * of the reconfiguration.
+ *
+ * Note that the driver should also call ieee80211_set_key_rx_seq()
+ * for the new key for each TID to set up sequence counters properly.
+ *
+ * IMPORTANT: If this replaces a key that is present in the hardware,
+ * then it will attempt to remove it during this call. In many cases
+ * this isn't what you want, so call ieee80211_remove_key() first for
+ * the key that's being replaced.
+ */
+struct ieee80211_key_conf *
+ieee80211_gtk_rekey_add(struct ieee80211_vif *vif,
+ struct ieee80211_key_conf *keyconf);
+
/**
* ieee80211_gtk_rekey_notify - notify userspace supplicant of rekeying
* @vif: virtual interface the rekeying was done on
void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta);
void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta,
u32 changed);
void (*free_sta)(void *priv, struct ieee80211_sta *sta,
projects / karo-tx-linux.git / blobdiff