X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=89835a4766a684468695b430ac8e7e7f1b76dabc;hb=bd91572e77013aad242e2d2d565bd730c043f8b8;hp=f3dc951e949f04255d90f35b5da4b78c7d015a67;hpb=f28b1c8aaa97a68028bb894bffb1690185c62b01;p=mv-sheeva.git

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index f3dc951e949..89835a4766a 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -43,11 +43,11 @@ parameter is applicable:
 	AVR32	AVR32 architecture is enabled.
 	AX25	Appropriate AX.25 support is enabled.
 	BLACKFIN Blackfin architecture is enabled.
+	DRM	Direct Rendering Management support is enabled.
+	DYNAMIC_DEBUG Build in debug messages and enable them at runtime
 	EDD	BIOS Enhanced Disk Drive Services (EDD) is enabled
 	EFI	EFI Partitioning (GPT) is enabled
 	EIDE	EIDE/ATAPI support is enabled.
-	DRM	Direct Rendering Management support is enabled.
-	DYNAMIC_DEBUG Build in debug messages and enable them at runtime
 	FB	The frame buffer device is enabled.
 	GCOV	GCOV profiling is enabled.
 	HW	Appropriate hardware is enabled.
@@ -199,11 +199,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			unusable.  The "log_buf_len" parameter may be useful
 			if you need to capture more output.
 
-	acpi_display_output=	[HW,ACPI]
-			acpi_display_output=vendor
-			acpi_display_output=video
-			See above.
-
 	acpi_irq_balance [HW,ACPI]
 			ACPI will balance active IRQs
 			default in APIC mode
@@ -403,6 +398,10 @@ and is between 256 and 4096 characters. It is defined in the file
 	bttv.pll=	See Documentation/video4linux/bttv/Insmod-options
 	bttv.tuner=	and Documentation/video4linux/bttv/CARDLIST
 
+	bulk_remove=off	[PPC]  This parameter disables the use of the pSeries
+			firmware feature for flushing multiple hpte entries
+			at a time.
+
 	c101=		[NET] Moxa C101 synchronous serial card
 
 	cachesize=	[BUGS=X86-32] Override level 2 CPU cache size detection.
@@ -655,11 +654,6 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	dscc4.setup=	[NET]
 
-	dynamic_printk	Enables pr_debug()/dev_dbg() calls if
-			CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
-			These can also be switched on/off via
-			<debugfs>/dynamic_printk/modules
-
 	earlycon=	[KNL] Output early console device and options.
 		uart[8250],io,<addr>[,options]
 		uart[8250],mmio,<addr>[,options]
@@ -884,6 +878,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			     controller
 	i8042.nopnp	[HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
 			     controllers
+	i8042.notimeout	[HW] Ignore timeout condition signalled by conroller
 	i8042.reset	[HW] Reset the controller during init and cleanup
 	i8042.unlock	[HW] Unlock (ignore) the keylock
 
@@ -1490,6 +1485,10 @@ and is between 256 and 4096 characters. It is defined in the file
 	mtdparts=	[MTD]
 			See drivers/mtd/cmdlinepart.c.
 
+	multitce=off	[PPC]  This parameter disables the use of the pSeries
+			firmware feature for updating multiple TCE entries
+			at a time.
+
 	onenand.bdry=	[HW,MTD] Flex-OneNAND Boundary Configuration
 
 			Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
@@ -1701,6 +1700,9 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	no-kvmclock	[X86,KVM] Disable paravirtualized KVM clock driver
 
+	no-kvmapf	[X86,KVM] Disable paravirtualized asynchronous page
+			fault handling.
+
 	nolapic		[X86-32,APIC] Do not enable or use the local APIC.
 
 	nolapic_timer	[X86-32,APIC] Do not use the local APIC timer.