X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=Kconfig;h=a759e4da2729e689cc7a0185cb22b257cb9c34fa;hb=refs%2Fheads%2Fkaro-txsd;hp=45a06696a19f52083be2c8df5b228f747c2b750b;hpb=c98b171e1098f94b2ff7720c45a25a602882f876;p=karo-tx-uboot.git

diff --git a/Kconfig b/Kconfig
index 45a06696a1..a759e4da27 100644
--- a/Kconfig
+++ b/Kconfig
@@ -137,74 +137,6 @@ endmenu		# General setup
 
 menu "Boot images"
 
-config SUPPORT_SPL
-	bool
-
-config SUPPORT_TPL
-	bool
-
-config SPL
-	bool
-	depends on SUPPORT_SPL
-	prompt "Enable SPL"
-	help
-	  If you want to build SPL as well as the normal image, say Y.
-
-config SPL_SYS_MALLOC_SIMPLE
-	bool
-	depends on SPL
-	prompt "Only use malloc_simple functions in the SPL"
-	help
-	  Say Y here to only use the *_simple malloc functions from
-	  malloc_simple.c, rather then using the versions from dlmalloc.c;
-	  this will make the SPL binary smaller at the cost of more heap
-	  usage as the *_simple malloc functions do not re-use free-ed mem.
-
-config SPL_STACK_R
-	depends on SPL
-	bool "Enable SDRAM location for SPL stack"
-	help
-	  SPL starts off execution in SRAM and thus typically has only a small
-	  stack available. Since SPL sets up DRAM while in its board_init_f()
-	  function, it is possible for the stack to move there before
-	  board_init_r() is reached. This option enables a special SDRAM
-	  location for the SPL stack. U-Boot SPL switches to this after
-	  board_init_f() completes, and before board_init_r() starts.
-
-config SPL_STACK_R_ADDR
-	depends on SPL_STACK_R
-	hex "SDRAM location for SPL stack"
-	help
-	  Specify the address in SDRAM for the SPL stack. This will be set up
-	  before board_init_r() is called.
-
-config SPL_STACK_R_MALLOC_SIMPLE_LEN
-	depends on SPL_STACK_R && SPL_SYS_MALLOC_SIMPLE
-	hex "Size of malloc_simple heap after switching to DRAM SPL stack"
-	default 0x100000
-	help
-	  Specify the amount of the stack to use as memory pool for
-	  malloc_simple after switching the stack to DRAM. This may be set
-	  to give board_init_r() a larger heap then the initial heap in
-	  SRAM which is limited to SYS_MALLOC_F_LEN bytes.
-
-config SPL_SEPARATE_BSS
-	depends on SPL
-	bool "BSS section is in a different memory region from text"
-	help
-	  Some platforms need a large BSS region in SPL and can provide this
-	  because RAM is already set up. In this case BSS can be moved to RAM.
-	  This option should then be enabled so that the correct device tree
-	  location is used. Normally we put the device tree at the end of BSS
-	  but with this option enabled, it goes at _image_binary_end.
-
-config TPL
-	bool
-	depends on SPL && SUPPORT_TPL
-	prompt "Enable TPL"
-	help
-	  If you want to build TPL as well as the normal image and SPL, say Y.
-
 config FIT
 	bool "Support Flattened Image Tree"
 	help