X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=README;h=6f3748d6dc4c2a8d4ce491d92420acffa9e42d36;hb=47293c18bae2e293667fe28f23201013ea8308ad;hp=68f5fb09180ec39b4f87306a75e9902347e48cec;hpb=844f07d8a1f1330c97631b23fbf6425db2dc1508;p=karo-tx-uboot.git diff --git a/README b/README index 68f5fb0918..6f3748d6dc 100644 --- a/README +++ b/README @@ -1,5 +1,5 @@ # -# (C) Copyright 2000 - 2009 +# (C) Copyright 2000 - 2011 # Wolfgang Denk, DENX Software Engineering, wd@denx.de. # # See file CREDITS for list of people who contributed to this @@ -164,7 +164,7 @@ Directory Hierarchy: /blackfin Files generic to Analog Devices Blackfin architecture /cpu CPU specific files /lib Architecture specific library files - /i386 Files generic to i386 architecture + /x86 Files generic to x86 architecture /cpu CPU specific files /lib Architecture specific library files /m68k Files generic to m68k architecture @@ -319,6 +319,11 @@ The following options need to be configured: CONFIG_SYS_PQ2FADS - PQ2FADS-ZU or PQ2FADS-VR CONFIG_SYS_8272ADS - MPC8272ADS +- Marvell Family Member + CONFIG_SYS_MVFS - define it if you want to enable + multiple fs option at one time + for marvell soc family + - MPC824X Family Member (if CONFIG_MPC824X is defined) Define exactly one of CONFIG_MPC8240, CONFIG_MPC8245 @@ -351,6 +356,13 @@ The following options need to be configured: Define this option if you want to enable the ICache only when Code runs from RAM. +- 85xx CPU Options: + CONFIG_SYS_FSL_TBCLK_DIV + + Defines the core time base clock divider ratio compared to the + system clock. On most PQ3 devices this is 8, on newer QorIQ + devices it can be 16 or 32. The ratio varies from SoC to Soc. + - Intel Monahans options: CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO @@ -463,6 +475,18 @@ The following options need to be configured: define this to a list of base addresses for each (supported) port. See e.g. include/configs/versatile.h + CONFIG_PL011_SERIAL_RLCR + + Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500) + have separate receive and transmit line control registers. Set + this variable to initialize the extra register. + + CONFIG_PL011_SERIAL_FLUSH_ON_INIT + + On some platforms (e.g. U8500) U-Boot is loaded by a second stage + boot loader that has already initialized the UART. Define this + variable to flush the UART at init time. + - Console Interface: Depending on board, define exactly one serial port @@ -620,6 +644,7 @@ The following options need to be configured: CONFIG_CMD_BOOTD bootd CONFIG_CMD_CACHE * icache, dcache CONFIG_CMD_CONSOLE coninfo + CONFIG_CMD_CRC32 * crc32 CONFIG_CMD_DATE * support for RTC, date/time... CONFIG_CMD_DHCP * DHCP support CONFIG_CMD_DIAG * Diagnostics @@ -632,22 +657,27 @@ The following options need to be configured: CONFIG_CMD_EDITENV edit env variable CONFIG_CMD_EEPROM * EEPROM read/write support CONFIG_CMD_ELF * bootelf, bootvx + CONFIG_CMD_EXPORTENV * export the environment CONFIG_CMD_SAVEENV saveenv CONFIG_CMD_FDC * Floppy Disk Support CONFIG_CMD_FAT * FAT partition support CONFIG_CMD_FDOS * Dos diskette Support CONFIG_CMD_FLASH flinfo, erase, protect CONFIG_CMD_FPGA FPGA device initialization support + CONFIG_CMD_GO * the 'go' command (exec code) + CONFIG_CMD_GREPENV * search environment CONFIG_CMD_HWFLOW * RTS/CTS hw flow control CONFIG_CMD_I2C * I2C serial bus support CONFIG_CMD_IDE * IDE harddisk support CONFIG_CMD_IMI iminfo CONFIG_CMD_IMLS List all found images CONFIG_CMD_IMMAP * IMMR dump support + CONFIG_CMD_IMPORTENV * import an environment CONFIG_CMD_IRQ * irqinfo CONFIG_CMD_ITEST Integer/string test of 2 values CONFIG_CMD_JFFS2 * JFFS2 Support CONFIG_CMD_KGDB * kgdb + CONFIG_CMD_LDRINFO ldrinfo (display Blackfin loader) CONFIG_CMD_LOADB loadb CONFIG_CMD_LOADS loads CONFIG_CMD_MD5SUM print md5 message digest @@ -675,7 +705,7 @@ The following options need to be configured: (requires CONFIG_CMD_I2C) CONFIG_CMD_SETGETDCR Support for DCR Register access (4xx only) - CONFIG_CMD_SHA1 print sha1 memory digest + CONFIG_CMD_SHA1SUM print sha1 memory digest (requires CONFIG_CMD_MEMORY) CONFIG_CMD_SOURCE "source" command Support CONFIG_CMD_SPI * SPI serial bus support @@ -709,10 +739,17 @@ The following options need to be configured: - Watchdog: CONFIG_WATCHDOG If this variable is defined, it enables watchdog - support. There must be support in the platform specific - code for a watchdog. For the 8xx and 8260 CPUs, the - SIU Watchdog feature is enabled in the SYPCR - register. + support for the SoC. There must be support in the SoC + specific code for a watchdog. For the 8xx and 8260 + CPUs, the SIU Watchdog feature is enabled in the SYPCR + register. When supported for a specific SoC is + available, then no further board specific code should + be needed to use it. + + CONFIG_HW_WATCHDOG + When using a watchdog circuitry external to the used + SoC, then define this variable and provide board + specific code for the "hw_watchdog_reset" function. - U-Boot Version: CONFIG_VERSION_VARIABLE @@ -738,6 +775,8 @@ The following options need to be configured: CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337 + CONFIG_SYS_RV3029_TCR - enable trickle charger on + RV3029 RTC. Note that if the RTC uses I2C, then the I2C interface must also be configured. See I2C Support, below. @@ -746,6 +785,10 @@ The following options need to be configured: CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO CONFIG_PCA953X_INFO - enable pca953x info command + The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of + chip-ngpio pairs that tell the PCA953X driver the number of + pins supported by a particular chip. + Note that if the GPIO device uses I2C, then the I2C interface must also be configured. See I2C Support, below. @@ -861,6 +904,18 @@ The following options need to be configured: Define this to use i/o functions instead of macros (some hardware wont work with macros) + CONFIG_FTGMAC100 + Support for Faraday's FTGMAC100 Gigabit SoC Ethernet + + CONFIG_FTGMAC100_EGIGA + Define this to use GE link update with gigabit PHY. + Define this if FTGMAC100 is connected to gigabit PHY. + If your system has 10/100 PHY only, it might not occur + wrong behavior. Because PHY usually return timeout or + useless data when polling gigabit status and gigabit + control registers. This behavior won't affect the + correctnessof 10/100 link speed update. + CONFIG_SMC911X Support for SMSC's LAN911x and LAN921x chips @@ -876,6 +931,18 @@ The following options need to be configured: automatically converts one 32 bit word to two 16 bit words you may also try CONFIG_SMC911X_32_BIT. + CONFIG_SH_ETHER + Support for Renesas on-chip Ethernet controller + + CONFIG_SH_ETHER_USE_PORT + Define the number of ports to be used + + CONFIG_SH_ETHER_PHY_ADDR + Define the ETH PHY's address + + CONFIG_SH_ETHER_CACHE_WRITEBACK + If this option is set, the driver enables cache flush. + - USB Support: At the moment only the UHCI host controller is supported (PIP405, MIP405, MPC5200); define @@ -1041,6 +1108,25 @@ The following options need to be configured: and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP or CONFIG_VIDEO_SED13806_16BPP + CONFIG_FSL_DIU_FB + Enable the Freescale DIU video driver. Reference boards for + SOCs that have a DIU should define this macro to enable DIU + support, and should also define these other macros: + + CONFIG_SYS_DIU_ADDR + CONFIG_VIDEO + CONFIG_CMD_BMP + CONFIG_CFB_CONSOLE + CONFIG_VIDEO_SW_CURSOR + CONFIG_VGA_AS_SINGLE_DEVICE + CONFIG_VIDEO_LOGO + CONFIG_VIDEO_BMP_LOGO + + The DIU driver will look for the 'video-mode' environment + variable, and if defined, enable the DIU as a console during + boot. See the documentation file README.video for a + description of this variable. + - Keyboard Support: CONFIG_KEYBOARD @@ -1243,7 +1329,6 @@ The following options need to be configured: driver in use must provide a function: mcast() to join/leave a multicast group. - CONFIG_BOOTP_RANDOM_DELAY - BOOTP Recovery Mode: CONFIG_BOOTP_RANDOM_DELAY @@ -1632,6 +1717,11 @@ The following options need to be configured: SPI EEPROM, also an instance works with Crystal A/D and D/As on the SACSng board) + CONFIG_SH_SPI + + Enables the driver for SPI controller on SuperH. Currently + only SH7757 is supported. + CONFIG_SPI_X Enables extended (16-bit) SPI EEPROM addressing. @@ -1936,6 +2026,28 @@ The following options need to be configured: example, some LED's) on your board. At the moment, the following checkpoints are implemented: +- Standalone program support: + CONFIG_STANDALONE_LOAD_ADDR + + This option allows to define board specific values + for the address where standalone program gets loaded, + thus overwriting the architecutre dependent default + settings. + +- Frame Buffer Address: + CONFIG_FB_ADDR + + Define CONFIG_FB_ADDR if you want to use specific address for + frame buffer. + Then system will reserve the frame buffer address to defined address + instead of lcd_setmem (this function grab the memory for frame buffer + by panel's size). + + Please see board_init_f function. + + If you want this config option then, + please define it at your board config file + Legacy uImage format: Arg Where When @@ -2273,7 +2385,10 @@ Configuration Settings: used) must be put below this limit, unless "bootm_low" enviroment variable is defined and non-zero. In such case all data for the Linux kernel must be between "bootm_low" - and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. + and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment + variable "bootm_mapsize" will override the value of + CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined, + then the value in "bootm_size" will be used instead. - CONFIG_SYS_BOOT_RAMDISK_HIGH: Enable initrd_high functionality. If defined then the @@ -2661,6 +2776,14 @@ Low Level (hardware related) configuration options: source code. It is used to make hardware dependant initializations. +- CONFIG_IDE_AHB: + Most IDE controllers were designed to be connected with PCI + interface. Only few of them were designed for AHB interface. + When software is doing ATA command and data transfer to + IDE devices through IDE-AHB controller, some additional + registers accessing to these kind of IDE-AHB controller + is requierd. + - CONFIG_SYS_IMMR: Physical address of the Internal Memory. DO NOT CHANGE unless you know exactly what you're doing! (11-4) [MPC8xx/82xx systems only] @@ -2771,6 +2894,24 @@ Low Level (hardware related) configuration options: Disable PCI-Express on systems where it is supported but not required. +- CONFIG_SYS_SRIO: + Chip has SRIO or not + +- CONFIG_SRIO1: + Board has SRIO 1 port available + +- CONFIG_SRIO2: + Board has SRIO 2 port available + +- CONFIG_SYS_SRIOn_MEM_VIRT: + Virtual Address of SRIO port 'n' memory region + +- CONFIG_SYS_SRIOn_MEM_PHYS: + Physical Address of SRIO port 'n' memory region + +- CONFIG_SYS_SRIOn_MEM_SIZE: + Size of SRIO port 'n' memory region + - CONFIG_SPD_EEPROM Get DDR timing information from an I2C EEPROM. Common with pluggable memory modules such as SODIMMs @@ -2851,6 +2992,12 @@ Low Level (hardware related) configuration options: that is executed before the actual U-Boot. E.g. when compiling a NAND SPL. +- CONFIG_USE_ARCH_MEMCPY + CONFIG_USE_ARCH_MEMSET + If these options are used a optimized version of memcpy/memset will + be used if available. These functions may be faster under some + conditions but may increase the binary size. + Building the Software: ====================== @@ -3091,7 +3238,16 @@ List of environment variables (most likely not complete): for use by the bootm command. See also "bootm_size" environment variable. Address defined by "bootm_low" is also the base of the initial memory mapping for the Linux - kernel -- see the description of CONFIG_SYS_BOOTMAPSZ. + kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and + bootm_mapsize. + + bootm_mapsize - Size of the initial memory mapping for the Linux kernel. + This variable is given as a hexadecimal number and it + defines the size of the memory region starting at base + address bootm_low that is accessible by the Linux kernel + during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used + as the default value if it is defined, and bootm_size is + used otherwise. bootm_size - Memory range available for image processing in the bootm command can be restricted. This variable is given as