X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=README;h=bc626dc7a83d9f2712c523ee0722eca7a0fa4739;hb=6d5565608f385b89f528ecf5680410cdc6cf63e9;hp=f41a6afc341d985cc824b262d8ffbecd1b7f8845;hpb=740f7e5c1dfe032ec207ea211770df32773bfaca;p=karo-tx-uboot.git

diff --git a/README b/README
index f41a6afc34..bc626dc7a8 100644
--- a/README
+++ b/README
@@ -3509,21 +3509,6 @@ FIT uImage format:
 		CONFIG_SPL_INIT_MINIMAL
 		Arch init code should be built for a very small image
 
-		CONFIG_SPL_LIBCOMMON_SUPPORT
-		Support for common/libcommon.o in SPL binary
-
-		CONFIG_SPL_LIBDISK_SUPPORT
-		Support for disk/libdisk.o in SPL binary
-
-		CONFIG_SPL_I2C_SUPPORT
-		Support for drivers/i2c/libi2c.o in SPL binary
-
-		CONFIG_SPL_GPIO_SUPPORT
-		Support for drivers/gpio/libgpio.o in SPL binary
-
-		CONFIG_SPL_MMC_SUPPORT
-		Support for drivers/mmc/libmmc.o in SPL binary
-
 		CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
 		CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
 		Address and partition on the MMC to load U-Boot from
@@ -3547,12 +3532,6 @@ FIT uImage format:
 		Partition on the MMC to load U-Boot from when the MMC is being
 		used in fs mode
 
-		CONFIG_SPL_FAT_SUPPORT
-		Support for fs/fat/libfat.o in SPL binary
-
-		CONFIG_SPL_EXT_SUPPORT
-		Support for EXT filesystem in SPL binary
-
 		CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
 		Filename to read to load U-Boot when reading from filesystem
 
@@ -3591,18 +3570,10 @@ FIT uImage format:
 		Support for a lightweight UBI (fastmap) scanner and
 		loader
 
-		CONFIG_SPL_MTD_SUPPORT
-		Support for the MTD subsystem within SPL.  Useful for
-		environment on NAND support within SPL.
-
 		CONFIG_SPL_NAND_RAW_ONLY
 		Support to boot only raw u-boot.bin images. Use this only
 		if you need to save space.
 
-		CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
-		Set for the SPL on PPC mpc8xxx targets, support for
-		drivers/ddr/fsl/libddr.o in SPL binary.
-
 		CONFIG_SPL_COMMON_INIT_DDR
 		Set for common ddr init with serial presence detect in
 		SPL binary.
@@ -3638,29 +3609,9 @@ FIT uImage format:
 		Support for an OMAP3-specific set of functions to return the
 		ID and MFR of the first attached NAND chip, if present.
 
-		CONFIG_SPL_SERIAL_SUPPORT
-		Support for drivers/serial/libserial.o in SPL binary
-
-		CONFIG_SPL_SPI_FLASH_SUPPORT
-		Support for drivers/mtd/spi/libspi_flash.o in SPL binary
-
-		CONFIG_SPL_SPI_SUPPORT
-		Support for drivers/spi/libspi.o in SPL binary
-
 		CONFIG_SPL_RAM_DEVICE
 		Support for running image already present in ram, in SPL binary
 
-		CONFIG_SPL_LIBGENERIC_SUPPORT
-		Support for lib/libgeneric.o in SPL binary
-
-		CONFIG_SPL_ENV_SUPPORT
-		Support for the environment operating in SPL binary
-
-		CONFIG_SPL_NET_SUPPORT
-		Support for the net/libnet.o in SPL binary.
-		It conflicts with SPL env from storage medium specified by
-		CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
-
 		CONFIG_SPL_PAD_TO
 		Image offset to which the SPL should be padded before appending
 		the SPL payload. By default, this is defined as
@@ -4947,12 +4898,6 @@ The Freescale Layerscape Debug Server Support supports the loading of
 "Debug Server firmware" and triggering SP boot-rom.
 This firmware often needs to be loaded during U-Boot booting.
 
-- CONFIG_FSL_DEBUG_SERVER
-	Enable the Debug Server for Layerscape SoCs.
-
-- CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE
-	Define minimum DDR size required for debug server image
-
 - CONFIG_SYS_MC_RSV_MEM_ALIGN
 	Define alignment of reserved memory MC requires