X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=doc%2FREADME.nand;h=0ff56331d5f92ec1ba0dbea186e40d36b4a06cb2;hb=53bea1369470c9f4ba3f93f26504bd83cd923c90;hp=e29188f1ec0cd4dd97a38ddb4bb7ed85645f83fe;hpb=434f2cfcad9f70231ad5a096325ba72ef0d2a2cc;p=karo-tx-uboot.git

diff --git a/doc/README.nand b/doc/README.nand
index e29188f1ec..0ff56331d5 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -99,12 +99,6 @@ Configuration Options:
    CONFIG_CMD_NAND_TORTURE
       Enables the torture command (see description of this command below).
 
-   CONFIG_MTD_NAND_ECC_JFFS2
-      Define this if you want the Error Correction Code information in
-      the out-of-band data to be formatted to match the JFFS2 file system.
-      CONFIG_MTD_NAND_ECC_YAFFS would be another useful choice for
-      someone to implement.
-
    CONFIG_SYS_MAX_NAND_DEVICE
       The maximum number of NAND devices you want to support.
 
@@ -194,24 +188,6 @@ Configuration Options:
 	This is used by SoC platforms which do not have built-in ELM
 	hardware engine required for BCH ECC correction.
 
-   CONFIG_SYS_NAND_BUSWIDTH_16BIT
-	Indicates that NAND device has 16-bit wide data-bus. In absence of this
-	config, bus-width of NAND device is assumed to be either 8-bit and later
-	determined by reading ONFI params.
-	Above config is useful when NAND device's bus-width information cannot
-	be determined from on-chip ONFI params, like in following scenarios:
-	- SPL boot does not support reading of ONFI parameters. This is done to
-	  keep SPL code foot-print small.
-	- In current U-Boot flow using nand_init(), driver initialization
-	  happens in board_nand_init() which is called before any device probe
-	  (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
-	  not available while configuring controller. So a static CONFIG_NAND_xx
-	  is needed to know the device's bus-width in advance.
-	Some drivers using above config are:
-	drivers/mtd/nand/mxc_nand.c
-	drivers/mtd/nand/ndfc.c
-	drivers/mtd/nand/omap_gpmc.c
-
 
 Platform specific options
 =========================
@@ -304,15 +280,14 @@ Platform specific options
 		Thus BCH16 can be supported on 4K page NAND.
 
 
+    CONFIG_NAND_OMAP_GPMC_PREFETCH
+	On OMAP platforms that use the GPMC controller
+	(CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
+	uses the prefetch mode to speed up read operations.
+
 NOTE:
 =====
 
-The current NAND implementation is based on what is in recent
-Linux kernels.  The old legacy implementation has been removed.
-
-If you have board code which used CONFIG_NAND_LEGACY, you'll need
-to convert to the current NAND interface for it to continue to work.
-
 The Disk On Chip driver is currently broken and has been for some time.
 There is a driver in drivers/mtd/nand, taken from Linux, that works with
 the current NAND system but has not yet been adapted to the u-boot