X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=include%2Fconfigs%2FTQM860M.h;h=ed496a1825052c5d05fa616fd46ea19f815c1431;hb=99070db0dc0b0e881841a0091f06d53351244a34;hp=1148f2e4efbcf5de5595a8beb89ff1334e3793f6;hpb=8206bfae3ab7f99965136384360ba2de0c6f4c3b;p=karo-tx-uboot.git

diff --git a/include/configs/TQM860M.h b/include/configs/TQM860M.h
index 1148f2e4ef..ed496a1825 100644
--- a/include/configs/TQM860M.h
+++ b/include/configs/TQM860M.h
@@ -36,10 +36,11 @@
 #define CONFIG_MPC860		1	/* This is a MPC860 CPU		*/
 #define CONFIG_TQM860M		1	/* ...on a TQM8xxM module	*/
 
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
+#define	CONFIG_SYS_TEXT_BASE	0x40000000
 
+#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
+#define CONFIG_SYS_SMC_RXBUFLEN	128
+#define CONFIG_SYS_MAXIDLE	10
 #define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/
 
 #define	CONFIG_BOOTCOUNT_LIMIT
@@ -134,9 +135,6 @@
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/
-#ifdef	CONFIG_SYS_HUSH_PARSER
-#define	CONFIG_SYS_PROMPT_HUSH_PS2	"> "
-#endif
 
 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
@@ -154,8 +152,6 @@
 
 #define	CONFIG_SYS_HZ			1000	/* decrementer freq: 1 ms ticks	*/
 
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-
 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
@@ -170,9 +166,8 @@
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
@@ -222,6 +217,8 @@
  * Dynamic MTD partition support
  */
 #define CONFIG_CMD_MTDPARTS
+#define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
+#define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"
 
 #define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
@@ -327,6 +324,7 @@
  *-----------------------------------------------------------------------
  */
 
+#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
 #define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/
 
 #undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
@@ -473,16 +471,13 @@
 			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
 #define CONFIG_SCC1_ENET
 #define CONFIG_FEC_ENET
-#define CONFIG_ETHPRIME		"SCC ETHERNET"
+#define CONFIG_ETHPRIME		"SCC"
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT	1
+#define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_HWCONFIG		1
 
 #endif	/* __CONFIG_H */