X-Git-Url: https://git.karo-electronics.de/?a=blobdiff_plain;f=include%2Fnet%2Fcfg80211.h;h=9c23f4d33e06c1ad1dab246b822d5dcc76c854ac;hb=a90a6e55f34f28190e4dc2a6a3660ef157827a8f;hp=63921672bed087f6f681c0058e0d34e825600a1c;hpb=36b150bbcc1125abaad89963420a37ff70686d5a;p=karo-tx-linux.git diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 63921672bed0..9c23f4d33e06 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -330,6 +330,9 @@ struct ieee80211_supported_band { * in a separate chapter. */ +#define VHT_MUMIMO_GROUPS_DATA_LEN (WLAN_MEMBERSHIP_LEN +\ + WLAN_USER_POSITION_LEN) + /** * struct vif_params - describes virtual interface parameters * @use_4addr: use 4-address frames @@ -339,10 +342,13 @@ struct ieee80211_supported_band { * This feature is only fully supported by drivers that enable the * %NL80211_FEATURE_MAC_ON_CREATE flag. Others may support creating ** only p2p devices with specified MAC. + * @vht_mumimo_groups: MU-MIMO groupID. used for monitoring only + * packets belonging to that MU-MIMO groupID. */ struct vif_params { - int use_4addr; - u8 macaddr[ETH_ALEN]; + int use_4addr; + u8 macaddr[ETH_ALEN]; + u8 vht_mumimo_groups[VHT_MUMIMO_GROUPS_DATA_LEN]; }; /** @@ -774,6 +780,7 @@ enum station_parameters_apply_mask { * (bitmask of BIT(NL80211_STA_FLAG_...)) * @listen_interval: listen interval or -1 for no change * @aid: AID or zero for no change + * @peer_aid: mesh peer AID or zero for no change * @plink_action: plink action to take * @plink_state: set the peer link state for a station * @ht_capa: HT capabilities of station @@ -805,6 +812,7 @@ struct station_parameters { u32 sta_modify_mask; int listen_interval; u16 aid; + u16 peer_aid; u8 supported_rates_len; u8 plink_action; u8 plink_state; @@ -1417,6 +1425,21 @@ struct cfg80211_ssid { u8 ssid_len; }; +/** + * struct cfg80211_scan_info - information about completed scan + * @scan_start_tsf: scan start time in terms of the TSF of the BSS that the + * wireless device that requested the scan is connected to. If this + * information is not available, this field is left zero. + * @tsf_bssid: the BSSID according to which %scan_start_tsf is set. + * @aborted: set to true if the scan was aborted for any reason, + * userspace will be notified of that + */ +struct cfg80211_scan_info { + u64 scan_start_tsf; + u8 tsf_bssid[ETH_ALEN] __aligned(2); + bool aborted; +}; + /** * struct cfg80211_scan_request - scan request description * @@ -1427,12 +1450,17 @@ struct cfg80211_ssid { * @scan_width: channel width for scanning * @ie: optional information element(s) to add into Probe Request or %NULL * @ie_len: length of ie in octets + * @duration: how long to listen on each channel, in TUs. If + * %duration_mandatory is not set, this is the maximum dwell time and + * the actual dwell time may be shorter. + * @duration_mandatory: if set, the scan duration must be as specified by the + * %duration field. * @flags: bit field of flags controlling operation * @rates: bitmap of rates to advertise for each band * @wiphy: the wiphy this was for * @scan_start: time (in jiffies) when the scan started * @wdev: the wireless device to scan for - * @aborted: (internal) scan request was notified as aborted + * @info: (internal) information about completed scan * @notified: (internal) scan request was notified as done or aborted * @no_cck: used to send probe requests at non CCK rate in 2GHz band * @mac_addr: MAC address used with randomisation @@ -1448,6 +1476,8 @@ struct cfg80211_scan_request { enum nl80211_bss_scan_width scan_width; const u8 *ie; size_t ie_len; + u16 duration; + bool duration_mandatory; u32 flags; u32 rates[NUM_NL80211_BANDS]; @@ -1461,7 +1491,8 @@ struct cfg80211_scan_request { /* internal */ struct wiphy *wiphy; unsigned long scan_start; - bool aborted, notified; + struct cfg80211_scan_info info; + bool notified; bool no_cck; /* keep last */ @@ -1594,12 +1625,19 @@ enum cfg80211_signal_type { * buffered on the device) and be accurate to about 10ms. * If the frame isn't buffered, just passing the return value of * ktime_get_boot_ns() is likely appropriate. + * @parent_tsf: the time at the start of reception of the first octet of the + * timestamp field of the frame. The time is the TSF of the BSS specified + * by %parent_bssid. + * @parent_bssid: the BSS according to which %parent_tsf is set. This is set to + * the BSS that requested the scan in which the beacon/probe was received. */ struct cfg80211_inform_bss { struct ieee80211_channel *chan; enum nl80211_bss_scan_width scan_width; s32 signal; u64 boottime_ns; + u64 parent_tsf; + u8 parent_bssid[ETH_ALEN] __aligned(2); }; /** @@ -2367,19 +2405,23 @@ struct cfg80211_qos_map { * (invoked with the wireless_dev mutex held) * * @connect: Connect to the ESS with the specified parameters. When connected, - * call cfg80211_connect_result() with status code %WLAN_STATUS_SUCCESS. - * If the connection fails for some reason, call cfg80211_connect_result() - * with the status from the AP. The driver is allowed to roam to other - * BSSes within the ESS when the other BSS matches the connect parameters. - * When such roaming is initiated by the driver, the driver is expected to - * verify that the target matches the configured security parameters and - * to use Reassociation Request frame instead of Association Request frame. - * The connect function can also be used to request the driver to perform - * a specific roam when connected to an ESS. In that case, the prev_bssid + * call cfg80211_connect_result()/cfg80211_connect_bss() with status code + * %WLAN_STATUS_SUCCESS. If the connection fails for some reason, call + * cfg80211_connect_result()/cfg80211_connect_bss() with the status code + * from the AP or cfg80211_connect_timeout() if no frame with status code + * was received. + * The driver is allowed to roam to other BSSes within the ESS when the + * other BSS matches the connect parameters. When such roaming is initiated + * by the driver, the driver is expected to verify that the target matches + * the configured security parameters and to use Reassociation Request + * frame instead of Association Request frame. + * The connect function can also be used to request the driver to perform a + * specific roam when connected to an ESS. In that case, the prev_bssid * parameter is set to the BSSID of the currently associated BSS as an - * indication of requesting reassociation. In both the driver-initiated and - * new connect() call initiated roaming cases, the result of roaming is - * indicated with a call to cfg80211_roamed() or cfg80211_roamed_bss(). + * indication of requesting reassociation. + * In both the driver-initiated and new connect() call initiated roaming + * cases, the result of roaming is indicated with a call to + * cfg80211_roamed() or cfg80211_roamed_bss(). * (invoked with the wireless_dev mutex held) * @disconnect: Disconnect from the BSS/ESS. * (invoked with the wireless_dev mutex held) @@ -3079,6 +3121,24 @@ struct wiphy_vendor_command { unsigned long *storage); }; +/** + * struct wiphy_iftype_ext_capab - extended capabilities per interface type + * @iftype: interface type + * @extended_capabilities: extended capabilities supported by the driver, + * additional capabilities might be supported by userspace; these are the + * 802.11 extended capabilities ("Extended Capabilities element") and are + * in the same format as in the information element. See IEEE Std + * 802.11-2012 8.4.2.29 for the defined fields. + * @extended_capabilities_mask: mask of the valid values + * @extended_capabilities_len: length of the extended capabilities + */ +struct wiphy_iftype_ext_capab { + enum nl80211_iftype iftype; + const u8 *extended_capabilities; + const u8 *extended_capabilities_mask; + u8 extended_capabilities_len; +}; + /** * struct wiphy - wireless hardware description * @reg_notifier: the driver's regulatory notification callback, @@ -3199,9 +3259,14 @@ struct wiphy_vendor_command { * additional capabilities might be supported by userspace; these are * the 802.11 extended capabilities ("Extended Capabilities element") * and are in the same format as in the information element. See - * 802.11-2012 8.4.2.29 for the defined fields. + * 802.11-2012 8.4.2.29 for the defined fields. These are the default + * extended capabilities to be used if the capabilities are not specified + * for a specific interface type in iftype_ext_capab. * @extended_capabilities_mask: mask of the valid values * @extended_capabilities_len: length of the extended capabilities + * @iftype_ext_capab: array of extended capabilities per interface type + * @num_iftype_ext_capab: number of interface types for which extended + * capabilities are specified separately. * @coalesce: packet coalescing support information * * @vendor_commands: array of vendor commands supported by the hardware @@ -3301,6 +3366,9 @@ struct wiphy { const u8 *extended_capabilities, *extended_capabilities_mask; u8 extended_capabilities_len; + const struct wiphy_iftype_ext_capab *iftype_ext_capab; + unsigned int num_iftype_ext_capab; + /* If multiple wiphys are registered and you're handed e.g. * a regular netdev with assigned ieee80211_ptr, you won't * know whether it points to a wiphy your driver has registered @@ -4031,10 +4099,10 @@ const char *reg_initiator_name(enum nl80211_reg_initiator initiator); * cfg80211_scan_done - notify that scan finished * * @request: the corresponding scan request - * @aborted: set to true if the scan was aborted for any reason, - * userspace will be notified of that + * @info: information about the completed scan */ -void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted); +void cfg80211_scan_done(struct cfg80211_scan_request *request, + struct cfg80211_scan_info *info); /** * cfg80211_sched_scan_results - notify that new scan results are available @@ -4680,7 +4748,7 @@ static inline void cfg80211_testmode_event(struct sk_buff *skb, gfp_t gfp) void cfg80211_connect_bss(struct net_device *dev, const u8 *bssid, struct cfg80211_bss *bss, const u8 *req_ie, size_t req_ie_len, const u8 *resp_ie, - size_t resp_ie_len, u16 status, gfp_t gfp); + size_t resp_ie_len, int status, gfp_t gfp); /** * cfg80211_connect_result - notify cfg80211 of connection result @@ -4709,6 +4777,29 @@ cfg80211_connect_result(struct net_device *dev, const u8 *bssid, resp_ie_len, status, gfp); } +/** + * cfg80211_connect_timeout - notify cfg80211 of connection timeout + * + * @dev: network device + * @bssid: the BSSID of the AP + * @req_ie: association request IEs (maybe be %NULL) + * @req_ie_len: association request IEs length + * @gfp: allocation flags + * + * It should be called by the underlying driver whenever connect() has failed + * in a sequence where no explicit authentication/association rejection was + * received from the AP. This could happen, e.g., due to not being able to send + * out the Authentication or Association Request frame or timing out while + * waiting for the response. + */ +static inline void +cfg80211_connect_timeout(struct net_device *dev, const u8 *bssid, + const u8 *req_ie, size_t req_ie_len, gfp_t gfp) +{ + cfg80211_connect_bss(dev, bssid, NULL, req_ie, req_ie_len, NULL, 0, -1, + gfp); +} + /** * cfg80211_roamed - notify cfg80211 of roaming *