- i2c@11000 {
- /* Is there anything on this? */
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- /*
- * PCA9655 GPIO expander, up to 1MHz clock.
- * 0-CON3 CLKREQ#
- * 1-CON3 PERST#
- * 2-
- * 3-CON3 W_DISABLE
- * 4-
- * 5-USB3 overcurrent
- * 6-USB3 power
- * 7-
- * 8-JP4 P1
- * 9-JP4 P4
- * 10-JP4 P5
- * 11-m.2 DEVSLP
- * 12-SFP_LOS
- * 13-SFP_TX_FAULT
- * 14-SFP_TX_DISABLE
- * 15-SFP_MOD_DEF0
- */
- expander0: gpio-expander@20 {
- /*
- * This is how it should be:
- * compatible = "onnn,pca9655",
- * "nxp,pca9555";
- * but you can't do this because of
- * the way I2C works.
- */
- compatible = "nxp,pca9555";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x20>;
-
- pcie1_0_clkreq {
- gpio-hog;
- gpios = <0 GPIO_ACTIVE_LOW>;
- input;
- line-name = "pcie1.0-clkreq";
- };
- pcie1_0_w_disable {
- gpio-hog;
- gpios = <3 GPIO_ACTIVE_LOW>;
- output-low;
- line-name = "pcie1.0-w-disable";
- };
- usb3_ilimit {
- gpio-hog;
- gpios = <5 GPIO_ACTIVE_LOW>;
- input;
- line-name = "usb3-current-limit";
- };
- usb3_power {
- gpio-hog;
- gpios = <6 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb3-power";
- };
- m2_devslp {
- gpio-hog;
- gpios = <11 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "m.2 devslp";
- };
- sfp_los {
- /* SFP loss of signal */
- gpio-hog;
- gpios = <12 GPIO_ACTIVE_HIGH>;
- input;
- line-name = "sfp-los";
- };
- sfp_tx_fault {
- /* SFP laser fault */
- gpio-hog;
- gpios = <13 GPIO_ACTIVE_HIGH>;
- input;
- line-name = "sfp-tx-fault";
- };
- sfp_tx_disable {
- /* SFP transmit disable */
- gpio-hog;
- gpios = <14 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "sfp-tx-disable";
- };
- sfp_mod_def0 {
- /* SFP module present */
- gpio-hog;
- gpios = <15 GPIO_ACTIVE_LOW>;
- input;
- line-name = "sfp-mod-def0";
- };
- };
-
- /* The MCP3021 is 100kHz clock only */
- mikrobus_adc: mcp3021@4c {
- compatible = "microchip,mcp3021";
- reg = <0x4c>;
- };
-
- /* Also something at 0x64 */
- };
-
- i2c@11100 {
- /*
- * Routed to SFP, mikrobus, and PCIe.
- * SFP limits this to 100kHz, and requires
- * an AT24C01A/02/04 with address pins tied
- * low, which takes addresses 0x50 and 0x51.
- * Mikrobus doesn't specify beyond an I2C
- * bus being present.
- * PCIe uses ARP to assign addresses, or
- * 0x63-0x64.
- */
- clock-frequency = <100000>;
- pinctrl-0 = <&clearfog_i2c1_pins>;
- pinctrl-names = "default";
- status = "okay";
- };
-