#define MAC_CLOCK_LOW (MAC_CLOCK_TICK&0xFF)
#define MAC_CLOCK_HIGH (MAC_CLOCK_TICK>>8)
-/* To disable a NuBus slot on Quadras we make that slot IRQ line an output set
- * high. On RBV we just use the slot interrupt enable register. On Macs with
- * genuine VIA chips we must use nubus_disabled to keep track of disabled slot
- * interrupts. When any slot IRQ is disabled we mask the (edge triggered) CA1
- * or "SLOTS" interrupt. When no slot is disabled, we unmask the CA1 interrupt.
- * So, on genuine VIAs, having more than one NuBus IRQ can mean trouble,
- * because closing one of those drivers can mask all of the NuBus interrupts.
- * Also, since we can't mask the unregistered slot IRQs on genuine VIAs, it's
- * possible to get interrupts from cards that MacOS or the ROM has configured
- * but we have not. FWIW, "Designing Cards and Drivers for Macintosh II and
- * Macintosh SE", page 9-8, says, a slot IRQ with no driver would crash MacOS.
+
+/*
+ * On Macs with a genuine VIA chip there is no way to mask an individual slot
+ * interrupt. This limitation also seems to apply to VIA clone logic cores in
+ * Quadra-like ASICs. (RBV and OSS machines don't have this limitation.)
+ *
+ * We used to fake it by configuring the relevent VIA pin as an output
+ * (to mask the interrupt) or input (to unmask). That scheme did not work on
+ * (at least) the Quadra 700. A NuBus card's /NMRQ signal is an open-collector
+ * circuit (see Designing Cards and Drivers for Macintosh II and Macintosh SE,
+ * p. 10-11 etc) but VIA outputs are not (see datasheet).
+ *
+ * Driving these outputs high must cause the VIA to source current and the
+ * card to sink current when it asserts /NMRQ. Current will flow but the pin
+ * voltage is uncertain and so the /NMRQ condition may still cause a transition
+ * at the VIA2 CA1 input (which explains the lost interrupts). A side effect
+ * is that a disabled slot IRQ can never be tested as pending or not.
+ *
+ * Driving these outputs low doesn't work either. All the slot /NMRQ lines are
+ * (active low) OR'd together to generate the CA1 (aka "SLOTS") interrupt (see
+ * The Guide To Macintosh Family Hardware, 2nd edition p. 167). If we drive a
+ * disabled /NMRQ line low, the falling edge immediately triggers a CA1
+ * interrupt and all slot interrupts after that will generate no transition
+ * and therefore no interrupt, even after being re-enabled.
+ *
+ * So we make the VIA port A I/O lines inputs and use nubus_disabled to keep
+ * track of their states. When any slot IRQ becomes disabled we mask the CA1
+ * umbrella interrupt. Only when all slot IRQs become enabled do we unmask
+ * the CA1 interrupt. It must remain enabled even when cards have no interrupt
+ * handler registered. Drivers must therefore disable a slot interrupt at the
+ * device before they call free_irq (like shared and autovector interrupts).
+ *
+ * There is also a related problem when MacOS is used to boot Linux. A network
+ * card brought up by a MacOS driver may raise an interrupt while Linux boots.
+ * This can be fatal since it can't be handled until the right driver loads
+ * (if such a driver exists at all). Apparently related to this hardware
+ * limitation, "Designing Cards and Drivers", p. 9-8, says that a slot
+ * interrupt with no driver would crash MacOS (the book was written before
+ * the appearance of Macs with RBV or OSS).
*/
+
static u8 nubus_disabled;
void via_debug_dump(void);
via2[gBufB] |= 0x02;
}
- /* Disable all the slot interrupts (where possible). */
+ /*
+ * Disable the slot interrupts. On some hardware that's not possible.
+ * On some hardware it's unclear what all of these I/O lines do.
+ */
switch (macintosh_config->via_type) {
case MAC_VIA_II:
- /* Just make the port A lines inputs. */
- switch(macintosh_config->ident) {
- case MAC_MODEL_II:
- case MAC_MODEL_IIX:
- case MAC_MODEL_IICX:
- case MAC_MODEL_SE30:
- /* The top two bits are RAM size outputs. */
- via2[vDirA] &= 0xC0;
- break;
- default:
- via2[vDirA] &= 0x80;
- }
+ case MAC_VIA_QUADRA:
+ pr_debug("VIA2 vDirA is 0x%02X\n", via2[vDirA]);
break;
case MAC_VIA_IIci:
/* RBV. Disable all the slot interrupts. SIER works like IER. */
via2[rSIER] = 0x7F;
break;
+ }
+}
+
+void via_nubus_irq_startup(int irq)
+{
+ int irq_idx = IRQ_IDX(irq);
+
+ switch (macintosh_config->via_type) {
+ case MAC_VIA_II:
case MAC_VIA_QUADRA:
- /* Disable the inactive slot interrupts by making those lines outputs. */
- if ((macintosh_config->adb_type != MAC_ADB_PB1) &&
- (macintosh_config->adb_type != MAC_ADB_PB2)) {
- via2[vBufA] |= 0x7F;
- via2[vDirA] |= 0x7F;
+ /* Make the port A line an input. Probably redundant. */
+ if (macintosh_config->via_type == MAC_VIA_II) {
+ /* The top two bits are RAM size outputs. */
+ via2[vDirA] &= 0xC0 | ~(1 << irq_idx);
+ } else {
+ /* Allow NuBus slots 9 through F. */
+ via2[vDirA] &= 0x80 | ~(1 << irq_idx);
}
+ /* fall through */
+ case MAC_VIA_IIci:
+ via_irq_enable(irq);
+ break;
+ }
+}
+
+void via_nubus_irq_shutdown(int irq)
+{
+ switch (macintosh_config->via_type) {
+ case MAC_VIA_II:
+ case MAC_VIA_QUADRA:
+ /* Ensure that the umbrella CA1 interrupt remains enabled. */
+ via_irq_enable(irq);
+ break;
+ case MAC_VIA_IIci:
+ via_irq_disable(irq);
break;
}
}
} else if (irq_src == 7) {
switch (macintosh_config->via_type) {
case MAC_VIA_II:
+ case MAC_VIA_QUADRA:
nubus_disabled &= ~(1 << irq_idx);
/* Enable the CA1 interrupt when no slot is disabled. */
if (!nubus_disabled)
*/
via2[rSIER] = IER_SET_BIT(irq_idx);
break;
- case MAC_VIA_QUADRA:
- /* Make the port A line an input to enable the slot irq.
- * But not on PowerBooks, that's ADB.
- */
- if ((macintosh_config->adb_type != MAC_ADB_PB1) &&
- (macintosh_config->adb_type != MAC_ADB_PB2))
- via2[vDirA] &= ~(1 << irq_idx);
- break;
}
}
}
} else if (irq_src == 7) {
switch (macintosh_config->via_type) {
case MAC_VIA_II:
+ case MAC_VIA_QUADRA:
nubus_disabled |= 1 << irq_idx;
if (nubus_disabled)
via2[gIER] = IER_CLR_BIT(1);
case MAC_VIA_IIci:
via2[rSIER] = IER_CLR_BIT(irq_idx);
break;
- case MAC_VIA_QUADRA:
- if ((macintosh_config->adb_type != MAC_ADB_PB1) &&
- (macintosh_config->adb_type != MAC_ADB_PB2))
- via2[vDirA] |= 1 << irq_idx;
- break;
}
}
}
projects / karo-tx-linux.git / commitdiff