ixgbe: Add X552 iXFI configuration helper function

X553 doesn't need all the initialization that X552 did for iXFI. This
patch will allow native SPI SFP+ to work with X553 devices.  Future
patches will add additional configuration as needed.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
index 7e6b9267ca9da3b4562c150a0e1aac35f8df92be..3e3458e2993497541840b821f01c331850ce0ffd 100644 (file)
--- a/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
+++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_x550.c
@@ -1128,47 +1128,17 @@ out:
        return ret;
 }
 
-/** ixgbe_setup_ixfi_x550em - Configure the KR PHY for iXFI mode.
+/**
+ *  ixgbe_setup_ixfi_x550em_x - MAC specific iXFI configuration
  *  @hw: pointer to hardware structure
- *  @speed: the link speed to force
  *
- *  Configures the integrated KR PHY to use iXFI mode. Used to connect an
- *  internal and external PHY at a specific speed, without autonegotiation.
+ *  iXfI configuration needed for ixgbe_mac_X550EM_x devices.
  **/
-static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed)
+static s32 ixgbe_setup_ixfi_x550em_x(struct ixgbe_hw *hw)
 {
        s32 status;
        u32 reg_val;
 
-       /* Disable AN and force speed to 10G Serial. */
-       status = ixgbe_read_iosf_sb_reg_x550(hw,
-                                       IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
-                                       IXGBE_SB_IOSF_TARGET_KR_PHY, &reg_val);
-       if (status)
-               return status;
-
-       reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
-       reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
-
-       /* Select forced link speed for internal PHY. */
-       switch (*speed) {
-       case IXGBE_LINK_SPEED_10GB_FULL:
-               reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
-               break;
-       case IXGBE_LINK_SPEED_1GB_FULL:
-               reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
-               break;
-       default:
-               /* Other link speeds are not supported by internal KR PHY. */
-               return IXGBE_ERR_LINK_SETUP;
-       }
-
-       status = ixgbe_write_iosf_sb_reg_x550(hw,
-                               IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
-                               IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
-       if (status)
-               return status;
-
        /* Disable training protocol FSM. */
        status = ixgbe_read_iosf_sb_reg_x550(hw,
                                IXGBE_KRM_RX_TRN_LINKUP_CTRL(hw->bus.lan_id),
@@ -1228,9 +1198,57 @@ static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed)
        status = ixgbe_write_iosf_sb_reg_x550(hw,
                                IXGBE_KRM_TX_COEFF_CTRL_1(hw->bus.lan_id),
                                IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
+       return status;
+}
+
+/** ixgbe_setup_ixfi_x550em - Configure the KR PHY for iXFI mode.
+ *  @hw: pointer to hardware structure
+ *  @speed: the link speed to force
+ *
+ *  Configures the integrated KR PHY to use iXFI mode. Used to connect an
+ *  internal and external PHY at a specific speed, without autonegotiation.
+ **/
+static s32 ixgbe_setup_ixfi_x550em(struct ixgbe_hw *hw, ixgbe_link_speed *speed)
+{
+       s32 status;
+       u32 reg_val;
+
+       /* Disable AN and force speed to 10G Serial. */
+       status = ixgbe_read_iosf_sb_reg_x550(hw,
+                                       IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+                                       IXGBE_SB_IOSF_TARGET_KR_PHY, &reg_val);
+       if (status)
+               return status;
+
+       reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_AN_ENABLE;
+       reg_val &= ~IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_MASK;
+
+       /* Select forced link speed for internal PHY. */
+       switch (*speed) {
+       case IXGBE_LINK_SPEED_10GB_FULL:
+               reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_10G;
+               break;
+       case IXGBE_LINK_SPEED_1GB_FULL:
+               reg_val |= IXGBE_KRM_LINK_CTRL_1_TETH_FORCE_SPEED_1G;
+               break;
+       default:
+               /* Other link speeds are not supported by internal KR PHY. */
+               return IXGBE_ERR_LINK_SETUP;
+       }
+
+       status = ixgbe_write_iosf_sb_reg_x550(hw,
+                               IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),
+                               IXGBE_SB_IOSF_TARGET_KR_PHY, reg_val);
        if (status)
                return status;
 
+       /* Additional configuration needed for x550em_x */
+       if (hw->mac.type == ixgbe_mac_X550EM_x) {
+               status = ixgbe_setup_ixfi_x550em_x(hw);
+               if (status)
+                       return status;
+       }
+
        /* Toggle port SW reset by AN reset. */
        status = ixgbe_read_iosf_sb_reg_x550(hw,
                                IXGBE_KRM_LINK_CTRL_1(hw->bus.lan_id),