(!(PCI_FUNC(dev->devfn) & 1)))
goto out;
+ if (dev->vendor == PCI_VENDOR_ID_JMICRON && PCI_FUNC(dev->devfn) != 1)
+ goto out;
+
pci_read_config_word(dev, PCI_COMMAND, &command);
if (!(command & PCI_COMMAND_IO)) {
printk(KERN_INFO "Skipping disabled %s IDE controller.\n", d->name);
{ PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_1, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 12},
{ PCI_VENDOR_ID_TOSHIBA,PCI_DEVICE_ID_TOSHIBA_PICCOLO_2, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 13},
{ PCI_VENDOR_ID_NETCELL,PCI_DEVICE_ID_REVOLUTION, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 14},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB361, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 15},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB363, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 16},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB365, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 17},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB366, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 18},
+ { PCI_VENDOR_ID_JMICRON, PCI_DEVICE_ID_JMICRON_JMB368, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 19},
/* Must come last. If you add entries adjust this table appropriately and the init_one code */
{ PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_CLASS_STORAGE_IDE << 8, 0xFFFFFF00UL, 0},
{ 0, },
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_963, quirk_sis_96x_smbus );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_LPC, quirk_sis_96x_smbus );
+#if defined(CONFIG_SCSI_SATA) || defined(CONFIG_SCSI_SATA_MODULE)
+
+/*
+ * If we are using libata we can drive this chip properly but must
+ * do this early on to make the additional device appear during
+ * the PCI scanning.
+ */
+
+static void __devinit quirk_jmicron_dualfn(struct pci_dev *pdev)
+{
+ u32 conf;
+ u8 hdr;
+
+ /* Only poke fn 0 */
+ if (PCI_FUNC(pdev->devfn))
+ return;
+
+ switch(pdev->device) {
+ case PCI_DEVICE_ID_JMICRON_JMB365:
+ case PCI_DEVICE_ID_JMICRON_JMB366:
+ /* Redirect IDE second PATA port to the right spot */
+ pci_read_config_dword(pdev, 0x80, &conf);
+ conf |= (1 << 24);
+ /* Fall through */
+ pci_write_config_dword(pdev, 0x80, conf);
+ case PCI_DEVICE_ID_JMICRON_JMB361:
+ case PCI_DEVICE_ID_JMICRON_JMB363:
+ pci_read_config_dword(pdev, 0x40, &conf);
+ /* Enable dual function mode, AHCI on fn 0, IDE fn1 */
+ /* Set the class codes correctly and then direct IDE 0 */
+ conf &= ~0x000F0200; /* Clear bit 9 and 16-19 */
+ conf |= 0x00C20002; /* Set bit 1, 17, 22, 23 */
+ pci_write_config_dword(pdev, 0x40, conf);
+
+ /* Reconfigure so that the PCI scanner discovers the
+ device is now multifunction */
+
+ pci_read_config_byte(pdev, PCI_HEADER_TYPE, &hdr);
+ pdev->hdr_type = hdr & 0x7f;
+ pdev->multifunction = !!(hdr & 0x80);
+
+ break;
+ }
+}
+
+DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_JMICRON, PCI_ANY_ID, quirk_jmicron_dualfn);
+
+#endif
+
#ifdef CONFIG_X86_IO_APIC
static void __init quirk_alder_ioapic(struct pci_dev *pdev)
{