--- /dev/null
+Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver
+
+Required properties:
+ - compatible: value should be one of the following:
+ "atmel,sama5d3-hlcdc"
+ - reg: base address and size of the HLCDC device registers.
+ - clock-names: the name of the 3 clocks requested by the HLCDC device.
+ Should contain "periph_clk", "sys_clk" and "slow_clk".
+ - clocks: should contain the 3 clocks requested by the HLCDC device.
+ - interrupts: should contain the description of the HLCDC interrupt line
+
+The HLCDC IP exposes two subdevices:
+ - a PWM chip: see ../pwm/atmel-hlcdc-pwm.txt
+ - a Display Controller: see ../drm/atmel-hlcdc-dc.txt
+
+Example:
+
+ hlcdc: hlcdc@f0030000 {
+ compatible = "atmel,sama5d3-hlcdc";
+ reg = <0xf0030000 0x2000>;
+ clocks = <&lcdc_clk>, <&lcdck>, <&clk32k>;
+ clock-names = "periph_clk","sys_clk", "slow_clk";
+ interrupts = <36 IRQ_TYPE_LEVEL_HIGH 0>;
+ status = "disabled";
+
+ hlcdc-display-controller {
+ compatible = "atmel,hlcdc-display-controller";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ hlcdc_panel_output: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+ };
+
+ hlcdc_pwm: hlcdc-pwm {
+ compatible = "atmel,hlcdc-pwm";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcd_pwm>;
+ #pwm-cells = <3>;
+ };
+ };
-BUCKn : for BUCKs, where n can lie in range 1 to 9.
example: BUCK1, BUCK5, BUCK9.
+ Regulators which can be turned off during system suspend:
+ -LDOn : 2, 6-8, 10-12, 14-16,
+ -BUCKn : 1-4.
+ Use standard regulator bindings for it ('regulator-off-in-suspend').
+
+
Example:
max77686@09 {
[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
+ users with tactile feedback. PWM period and duty-cycle are varied in
+ order to provide the approprite level of feedback.
+
+ Required properties:
+ - compatible : Must be "maxim,max77693-hpatic"
+ - haptic-supply : power supply for the haptic motor
+ [*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+ - pwms : phandle to the physical PWM(Pulse Width Modulation) device.
+ PWM properties should be named "pwms". And number of cell is different
+ for each pwm device.
+ To get more informations, please refer to documentaion.
+ [*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+
Example:
max77693@66 {
compatible = "maxim,max77693";
regulator-boot-on;
};
};
+
+ haptic {
+ compatible = "maxim,max77693-haptic";
+ haptic-supply = <&haptic_supply>;
+ pwms = <&pwm 0 40000 0>;
+ pwm-names = "haptic";
+ };
};
-* Samsung S2MPS11, S2MPS14 and S2MPU02 Voltage and Current Regulator
+* Samsung S2MPS11, S2MPS13, S2MPS14 and S2MPU02 Voltage and Current Regulator
The Samsung S2MPS11 is a multi-function device which includes voltage and
current regulators, RTC, charger controller and other sub-blocks. It is
addressed by the host system using different I2C slave addresses.
Required properties:
-- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps14-pmic"
- or "samsung,s2mpu02-pmic".
+- compatible: Should be "samsung,s2mps11-pmic" or "samsung,s2mps13-pmic"
+ or "samsung,s2mps14-pmic" or "samsung,s2mpu02-pmic".
- reg: Specifies the I2C slave address of the pmic block. It should be 0x66.
Optional properties:
- interrupts: Interrupt specifiers for interrupt sources.
Optional nodes:
-- clocks: s2mps11 and s5m8767 provide three(AP/CP/BT) buffered 32.768 KHz
- outputs, so to register these as clocks with common clock framework
+- clocks: s2mps11, s2mps13 and s5m8767 provide three(AP/CP/BT) buffered 32.768
+ KHz outputs, so to register these as clocks with common clock framework
instantiate a sub-node named "clocks". It uses the common clock binding
documented in :
[Documentation/devicetree/bindings/clock/clock-bindings.txt]
the clock which they consume.
Clock ID Devices
----------------------------------------------------------
- 32KhzAP 0 S2MPS11, S2MPS14, S5M8767
- 32KhzCP 1 S2MPS11, S5M8767
- 32KhzBT 2 S2MPS11, S2MPS14, S5M8767
+ 32KhzAP 0 S2MPS11, S2MPS13, S2MPS14, S5M8767
+ 32KhzCP 1 S2MPS11, S2MPS13, S5M8767
+ 32KhzBT 2 S2MPS11, S2MPS13, S2MPS14, S5M8767
- - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps14-clk",
- "samsung,s5m8767-clk"
+ - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk",
+ "samsung,s2mps14-clk", "samsung,s5m8767-clk"
- regulators: The regulators of s2mps11 that have to be instantiated should be
included in a sub-node named 'regulators'. Regulator nodes included in this
- LDOn
- valid values for n are:
- S2MPS11: 1 to 38
+ - S2MPS13: 1 to 40
- S2MPS14: 1 to 25
- S2MPU02: 1 to 28
- Example: LDO1, LDO2, LDO28
- BUCKn
- valid values for n are:
- S2MPS11: 1 to 10
+ - S2MPS13: 1 to 10
- S2MPS14: 1 to 5
- S2MPU02: 1 to 7
- Example: BUCK1, BUCK2, BUCK9
specific extensions.
- "samsung,exynos5420-dw-mshc": for controllers with Samsung Exynos5420
specific extensions.
+ - "samsung,exynos7-dw-mshc": for controllers with Samsung Exynos7
+ specific extensions.
+ - "samsung,exynos7-dw-mshc-smu": for controllers with Samsung Exynos7
+ specific extensions having an SMU.
* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
--- /dev/null
+* Imagination specific extensions to the Synopsys Designware Mobile Storage
+ Host Controller
+
+The Synopsys designware mobile storage host controller is used to interface
+a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
+differences between the core Synopsys dw mshc controller properties described
+by synopsys-dw-mshc.txt and the properties used by the Imagination specific
+extensions to the Synopsys Designware Mobile Storage Host Controller.
+
+Required Properties:
+
+* compatible: should be
+ - "img,pistachio-dw-mshc": for Pistachio SoCs
+
+Example:
+
+ mmc@18142000 {
+ compatible = "img,pistachio-dw-mshc";
+ reg = <0x18142000 0x400>;
+ interrupts = <GIC_SHARED 39 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&system_clk>, <&sdhost_clk>;
+ clock-names = "biu", "ciu";
+
+ fifo-depth = <0x20>;
+ bus-width = <4>;
+ num-slots = <1>;
+ disable-wp;
+ };
* for "marvell,armada-380-sdhci", two register areas. The first one
for the SDHCI registers themselves, and the second one for the
AXI/Mbus bridge registers of the SDHCI unit.
+- clocks: Array of clocks required for SDHCI; requires at least one for
+ I/O clock.
+- clock-names: Array of names corresponding to clocks property; shall be
+ "io" for I/O clock and "core" for optional core clock.
Optional properties:
- mrvl,clk-delay-cycles: Specify a number of cycles to delay for tuning.
reg = <0xd4280800 0x800>;
bus-width = <8>;
interrupts = <27>;
+ clocks = <&chip CLKID_SDIO1XIN>, <&chip CLKID_SDIO1>;
+ clock-names = "io", "core";
non-removable;
mrvl,clk-delay-cycles = <31>;
};
reg = <0xd8000 0x1000>, <0xdc000 0x100>;
interrupts = <0 25 0x4>;
clocks = <&gateclk 17>;
+ clock-names = "io";
mrvl,clk-delay-cycles = <0x1F>;
};
F: net/ax25/
AZ6007 DVB DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: fs/btrfs/
BTTV VIDEO4LINUX DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: include/media/cx2341x*
CX88 VIDEO4LINUX DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
EDAC-CORE
M: Doug Thompson <dougthompson@xmission.com>
M: Borislav Petkov <bp@alien8.de>
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Supported
F: drivers/edac/e7xxx_edac.c
EDAC-GHES
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Maintained
F: drivers/edac/i5000_edac.c
EDAC-I5400
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Maintained
F: drivers/edac/i5400_edac.c
EDAC-I7300
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Maintained
F: drivers/edac/i7300_edac.c
EDAC-I7CORE
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Maintained
F: drivers/edac/r82600_edac.c
EDAC-SBRIDGE
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-edac@vger.kernel.org
W: bluesmoke.sourceforge.net
S: Maintained
F: drivers/net/ethernet/ibm/ehea/
EM28XX VIDEO4LINUX DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: drivers/media/radio/radio-maxiradio*
MEDIA INPUT INFRASTRUCTURE (V4L/DVB)
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
P: LinuxTV.org Project
L: linux-media@vger.kernel.org
W: http://linuxtv.org
F: drivers/media/i2c/saa6588*
SAA7134 VIDEO4LINUX DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: drivers/media/radio/si4713/radio-usb-si4713.c
SIANO DVB DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: drivers/leds/leds-net48xx.c
SOFTLOGIC 6x10 MPEG CODEC
-M: Ismael Luceno <ismael.luceno@corp.bluecherry.net>
+M: Bluecherry Maintainers <maintainers@bluecherrydvr.com>
+M: Andrey Utkin <andrey.utkin@corp.bluecherry.net>
+M: Andrey Utkin <andrey.krieger.utkin@gmail.com>
L: linux-media@vger.kernel.org
S: Supported
F: drivers/media/pci/solo6x10/
F: drivers/media/i2c/tda9840*
TEA5761 TUNER DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: drivers/media/tuners/tea5761.*
TEA5767 TUNER DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: mm/shmem.c
TM6000 VIDEO4LINUX DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
F: arch/x86/kernel/cpu/mcheck/*
XC2028/3028 TUNER DRIVER
-M: Mauro Carvalho Chehab <m.chehab@samsung.com>
+M: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
L: linux-media@vger.kernel.org
W: http://linuxtv.org
T: git git://linuxtv.org/media_tree.git
VERSION = 3
PATCHLEVEL = 18
SUBLEVEL = 0
-EXTRAVERSION = -rc7
+EXTRAVERSION =
NAME = Diseased Newt
# *DOCUMENTATION*
#include <linux/i2c-gpio.h>
#include <linux/atmel-mci.h>
#include <linux/platform_data/crypto-atmel.h>
+#include <linux/platform_data/mmc-atmel-mci.h>
#include <linux/platform_data/at91_adc.h>
#include <mach/at91_matrix.h>
#include <mach/at91sam9_smc.h>
#include <linux/platform_data/dma-atmel.h>
-#include <mach/atmel-mci.h>
#include <mach/hardware.h>
#include <media/atmel-isi.h>
#include <linux/i2c.h>
#include <linux/spi/spi.h>
#include <linux/usb/musb.h>
+#include <linux/mmc/host.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <linux/platform_data/mtd-onenand-omap2.h>
+#include <linux/platform_data/mmc-omap.h>
#include <linux/mfd/menelaus.h>
#include <sound/tlv320aic3x.h>
* Current flows to eMMC when eMMC is off and the data lines are pulled up,
* so pull them down. N.B. we pull 8 lines because we are using 8 lines.
*/
-static void rx51_mmc2_remux(struct device *dev, int slot, int power_on)
+static void rx51_mmc2_remux(struct device *dev, int power_on)
{
if (power_on)
omap_mux_write_array(partition, rx51_mmc2_on_mux);
.cover_only = true,
.gpio_cd = 160,
.gpio_wp = -EINVAL,
- .power_saving = true,
},
{
.name = "internal",
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.nonremovable = true,
- .power_saving = true,
.remux = rx51_mmc2_remux,
},
{} /* Terminator */
#include <linux/string.h>
#include <linux/delay.h>
#include <linux/gpio.h>
+#include <linux/mmc/host.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include "soc.h"
#include "omap_device.h"
#include "omap-pm.h"
#include "mux.h"
-#include "mmc.h"
#include "hsmmc.h"
#include "control.h"
#define HSMMC_NAME_LEN 9
-#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
-
-static int hsmmc_get_context_loss(struct device *dev)
-{
- return omap_pm_get_dev_context_loss_count(dev);
-}
-
-#else
-#define hsmmc_get_context_loss NULL
-#endif
-
-static void omap_hsmmc1_before_set_reg(struct device *dev, int slot,
- int power_on, int vdd)
+static void omap_hsmmc1_before_set_reg(struct device *dev,
+ int power_on, int vdd)
{
u32 reg, prog_io;
- struct omap_mmc_platform_data *mmc = dev->platform_data;
+ struct omap_hsmmc_platform_data *mmc = dev->platform_data;
- if (mmc->slots[0].remux)
- mmc->slots[0].remux(dev, slot, power_on);
+ if (mmc->remux)
+ mmc->remux(dev, power_on);
/*
* Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
}
- if (mmc->slots[0].internal_clock) {
+ if (mmc->internal_clock) {
reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
reg |= OMAP2_MMCSDIO1ADPCLKISEL;
omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0);
}
}
-static void omap_hsmmc1_after_set_reg(struct device *dev, int slot,
- int power_on, int vdd)
+static void omap_hsmmc1_after_set_reg(struct device *dev, int power_on, int vdd)
{
u32 reg;
}
}
-static void hsmmc2_select_input_clk_src(struct omap_mmc_platform_data *mmc)
+static void hsmmc2_select_input_clk_src(struct omap_hsmmc_platform_data *mmc)
{
u32 reg;
reg = omap_ctrl_readl(control_devconf1_offset);
- if (mmc->slots[0].internal_clock)
+ if (mmc->internal_clock)
reg |= OMAP2_MMCSDIO2ADPCLKISEL;
else
reg &= ~OMAP2_MMCSDIO2ADPCLKISEL;
omap_ctrl_writel(reg, control_devconf1_offset);
}
-static void hsmmc2_before_set_reg(struct device *dev, int slot,
- int power_on, int vdd)
+static void hsmmc2_before_set_reg(struct device *dev, int power_on, int vdd)
{
- struct omap_mmc_platform_data *mmc = dev->platform_data;
+ struct omap_hsmmc_platform_data *mmc = dev->platform_data;
- if (mmc->slots[0].remux)
- mmc->slots[0].remux(dev, slot, power_on);
+ if (mmc->remux)
+ mmc->remux(dev, power_on);
if (power_on)
hsmmc2_select_input_clk_src(mmc);
}
-static int am35x_hsmmc2_set_power(struct device *dev, int slot,
- int power_on, int vdd)
+static int am35x_hsmmc2_set_power(struct device *dev, int power_on, int vdd)
{
- struct omap_mmc_platform_data *mmc = dev->platform_data;
+ struct omap_hsmmc_platform_data *mmc = dev->platform_data;
if (power_on)
hsmmc2_select_input_clk_src(mmc);
return 0;
}
-static int nop_mmc_set_power(struct device *dev, int slot, int power_on,
- int vdd)
+static int nop_mmc_set_power(struct device *dev, int power_on, int vdd)
{
return 0;
}
-static inline void omap_hsmmc_mux(struct omap_mmc_platform_data *mmc_controller,
- int controller_nr)
+static inline void omap_hsmmc_mux(struct omap_hsmmc_platform_data
+ *mmc_controller, int controller_nr)
{
- if (gpio_is_valid(mmc_controller->slots[0].switch_pin) &&
- (mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
- omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
- OMAP_PIN_INPUT_PULLUP);
- if (gpio_is_valid(mmc_controller->slots[0].gpio_wp) &&
- (mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
- omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
- OMAP_PIN_INPUT_PULLUP);
+ if (gpio_is_valid(mmc_controller->switch_pin) &&
+ (mmc_controller->switch_pin < OMAP_MAX_GPIO_LINES))
+ omap_mux_init_gpio(mmc_controller->switch_pin,
+ OMAP_PIN_INPUT_PULLUP);
+ if (gpio_is_valid(mmc_controller->gpio_wp) &&
+ (mmc_controller->gpio_wp < OMAP_MAX_GPIO_LINES))
+ omap_mux_init_gpio(mmc_controller->gpio_wp,
+ OMAP_PIN_INPUT_PULLUP);
if (cpu_is_omap34xx()) {
if (controller_nr == 0) {
omap_mux_init_signal("sdmmc1_clk",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat0",
OMAP_PIN_INPUT_PULLUP);
- if (mmc_controller->slots[0].caps &
+ if (mmc_controller->caps &
(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc1_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc1_dat3",
OMAP_PIN_INPUT_PULLUP);
}
- if (mmc_controller->slots[0].caps &
+ if (mmc_controller->caps &
MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc1_dat4",
OMAP_PIN_INPUT_PULLUP);
* For 8 wire configurations, Lines DAT4, 5, 6 and 7
* need to be muxed in the board-*.c files
*/
- if (mmc_controller->slots[0].caps &
+ if (mmc_controller->caps &
(MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)) {
omap_mux_init_signal("sdmmc2_dat1",
OMAP_PIN_INPUT_PULLUP);
omap_mux_init_signal("sdmmc2_dat3",
OMAP_PIN_INPUT_PULLUP);
}
- if (mmc_controller->slots[0].caps &
+ if (mmc_controller->caps &
MMC_CAP_8_BIT_DATA) {
omap_mux_init_signal("sdmmc2_dat4.sdmmc2_dat4",
OMAP_PIN_INPUT_PULLUP);
}
static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
- struct omap_mmc_platform_data *mmc)
+ struct omap_hsmmc_platform_data *mmc)
{
char *hc_name;
else
snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i",
c->mmc, 1);
- mmc->slots[0].name = hc_name;
- mmc->nr_slots = 1;
- mmc->slots[0].caps = c->caps;
- mmc->slots[0].pm_caps = c->pm_caps;
- mmc->slots[0].internal_clock = !c->ext_clock;
- mmc->max_freq = c->max_freq;
+ mmc->name = hc_name;
+ mmc->caps = c->caps;
+ mmc->internal_clock = !c->ext_clock;
mmc->reg_offset = 0;
- mmc->get_context_loss_count = hsmmc_get_context_loss;
- mmc->slots[0].switch_pin = c->gpio_cd;
- mmc->slots[0].gpio_wp = c->gpio_wp;
+ mmc->switch_pin = c->gpio_cd;
+ mmc->gpio_wp = c->gpio_wp;
- mmc->slots[0].remux = c->remux;
- mmc->slots[0].init_card = c->init_card;
+ mmc->remux = c->remux;
+ mmc->init_card = c->init_card;
if (c->cover_only)
- mmc->slots[0].cover = 1;
+ mmc->cover = 1;
if (c->nonremovable)
- mmc->slots[0].nonremovable = 1;
-
- if (c->power_saving)
- mmc->slots[0].power_saving = 1;
-
- if (c->no_off)
- mmc->slots[0].no_off = 1;
-
- if (c->no_off_init)
- mmc->slots[0].no_regulator_off_init = c->no_off_init;
-
- if (c->vcc_aux_disable_is_sleep)
- mmc->slots[0].vcc_aux_disable_is_sleep = 1;
+ mmc->nonremovable = 1;
/*
* NOTE: MMC slots should have a Vcc regulator set up.
* temporary HACK: ocr_mask instead of fixed supply
*/
if (soc_is_am35xx())
- mmc->slots[0].ocr_mask = MMC_VDD_165_195 |
+ mmc->ocr_mask = MMC_VDD_165_195 |
MMC_VDD_26_27 |
MMC_VDD_27_28 |
MMC_VDD_29_30 |
MMC_VDD_30_31 |
MMC_VDD_31_32;
else
- mmc->slots[0].ocr_mask = c->ocr_mask;
+ mmc->ocr_mask = c->ocr_mask;
if (!soc_is_am35xx())
- mmc->slots[0].features |= HSMMC_HAS_PBIAS;
+ mmc->features |= HSMMC_HAS_PBIAS;
switch (c->mmc) {
case 1:
- if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
+ if (mmc->features & HSMMC_HAS_PBIAS) {
/* on-chip level shifting via PBIAS0/PBIAS1 */
- mmc->slots[0].before_set_reg =
+ mmc->before_set_reg =
omap_hsmmc1_before_set_reg;
- mmc->slots[0].after_set_reg =
+ mmc->after_set_reg =
omap_hsmmc1_after_set_reg;
}
if (soc_is_am35xx())
- mmc->slots[0].set_power = nop_mmc_set_power;
+ mmc->set_power = nop_mmc_set_power;
/* OMAP3630 HSMMC1 supports only 4-bit */
if (cpu_is_omap3630() &&
(c->caps & MMC_CAP_8_BIT_DATA)) {
c->caps &= ~MMC_CAP_8_BIT_DATA;
c->caps |= MMC_CAP_4_BIT_DATA;
- mmc->slots[0].caps = c->caps;
+ mmc->caps = c->caps;
}
break;
case 2:
if (soc_is_am35xx())
- mmc->slots[0].set_power = am35x_hsmmc2_set_power;
+ mmc->set_power = am35x_hsmmc2_set_power;
if (c->ext_clock)
c->transceiver = 1;
c->caps &= ~MMC_CAP_8_BIT_DATA;
c->caps |= MMC_CAP_4_BIT_DATA;
}
- if (mmc->slots[0].features & HSMMC_HAS_PBIAS) {
+ if (mmc->features & HSMMC_HAS_PBIAS) {
/* off-chip level shifting, or none */
- mmc->slots[0].before_set_reg = hsmmc2_before_set_reg;
- mmc->slots[0].after_set_reg = NULL;
+ mmc->before_set_reg = hsmmc2_before_set_reg;
+ mmc->after_set_reg = NULL;
}
break;
case 3:
case 4:
case 5:
- mmc->slots[0].before_set_reg = NULL;
- mmc->slots[0].after_set_reg = NULL;
+ mmc->before_set_reg = NULL;
+ mmc->after_set_reg = NULL;
break;
default:
pr_err("MMC%d configuration not supported!\n", c->mmc);
void omap_hsmmc_late_init(struct omap2_hsmmc_info *c)
{
struct platform_device *pdev;
- struct omap_mmc_platform_data *mmc_pdata;
+ struct omap_hsmmc_platform_data *mmc_pdata;
int res;
if (omap_hsmmc_done != 1)
if (!mmc_pdata)
continue;
- mmc_pdata->slots[0].switch_pin = c->gpio_cd;
- mmc_pdata->slots[0].gpio_wp = c->gpio_wp;
+ mmc_pdata->switch_pin = c->gpio_cd;
+ mmc_pdata->gpio_wp = c->gpio_wp;
res = omap_device_register(pdev);
if (res)
struct omap_device *od;
struct platform_device *pdev;
char oh_name[MAX_OMAP_MMC_HWMOD_NAME_LEN];
- struct omap_mmc_platform_data *mmc_data;
- struct omap_mmc_dev_attr *mmc_dev_attr;
+ struct omap_hsmmc_platform_data *mmc_data;
+ struct omap_hsmmc_dev_attr *mmc_dev_attr;
char *name;
int res;
- mmc_data = kzalloc(sizeof(struct omap_mmc_platform_data), GFP_KERNEL);
+ mmc_data = kzalloc(sizeof(*mmc_data), GFP_KERNEL);
if (!mmc_data) {
pr_err("Cannot allocate memory for mmc device!\n");
return;
}
res = platform_device_add_data(pdev, mmc_data,
- sizeof(struct omap_mmc_platform_data));
+ sizeof(struct omap_hsmmc_platform_data));
if (res) {
pr_err("Could not add pdata for %s\n", name);
goto put_pdev;
platform_device_put(pdev);
free_name:
- kfree(mmc_data->slots[0].name);
+ kfree(mmc_data->name);
free_mmc:
kfree(mmc_data);
u8 mmc; /* controller 1/2/3 */
u32 caps; /* 4/8 wires and any additional host
* capabilities OR'd (ref. linux/mmc/host.h) */
- u32 pm_caps; /* PM capabilities */
bool transceiver; /* MMC-2 option */
bool ext_clock; /* use external pin for input clock */
bool cover_only; /* No card detect - just cover switch */
bool nonremovable; /* Nonremovable e.g. eMMC */
- bool power_saving; /* Try to sleep or power off when possible */
- bool no_off; /* power_saving and power is not to go off */
- bool no_off_init; /* no power off when not in MMC sleep state */
- bool vcc_aux_disable_is_sleep; /* Regulator off remapped to sleep */
bool deferred; /* mmc needs a deferred probe */
int gpio_cd; /* or -EINVAL */
int gpio_wp; /* or -EINVAL */
char *name; /* or NULL for default */
struct platform_device *pdev; /* mmc controller instance */
int ocr_mask; /* temporary HACK */
- int max_freq; /* maximum clock, if constrained by external
- * circuitry, or 0 for default */
/* Remux (pad configuration) when powering on/off */
- void (*remux)(struct device *dev, int slot, int power_on);
+ void (*remux)(struct device *dev, int power_on);
/* init some special card */
void (*init_card)(struct mmc_card *card);
};
-#include <linux/mmc/host.h>
-#include <linux/platform_data/mmc-omap.h>
#define OMAP24XX_NR_MMC 2
#define OMAP2420_MMC_SIZE OMAP1_MMC_SIZE
#define OMAP4_MMC_REG_OFFSET 0x100
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data);
-#else
-static inline void omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
-{
-}
-#endif
-
struct omap_hwmod;
int omap_msdi_reset(struct omap_hwmod *oh);
#include "soc.h"
#include "iomap.h"
#include "common.h"
-#include "mmc.h"
#include "prminst44xx.h"
#include "prcm_mpu44xx.h"
#include "omap4-sar-layout.h"
#include <linux/i2c-omap.h>
#include <linux/platform_data/asoc-ti-mcbsp.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <linux/omap-dma.h>
#include <plat/dmtimer.h>
#include "omap_hwmod.h"
-#include "mmc.h"
#include "l3_2xxx.h"
#include "soc.h"
{ .role = "dbck", .clk = "mmchsdb1_fck" },
};
-static struct omap_mmc_dev_attr mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
*/
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include "omap_hwmod.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
#include "cm33xx.h"
#include "prm33xx.h"
};
/* mmc0 */
-static struct omap_mmc_dev_attr am33xx_mmc0_dev_attr = {
+static struct omap_hsmmc_dev_attr am33xx_mmc0_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
};
/* mmc1 */
-static struct omap_mmc_dev_attr am33xx_mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr am33xx_mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
};
/* mmc2 */
-static struct omap_mmc_dev_attr am33xx_mmc2_dev_attr = {
+static struct omap_hsmmc_dev_attr am33xx_mmc2_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
struct omap_hwmod am33xx_mmc2_hwmod = {
#include "prm33xx.h"
#include "prm-regbits-33xx.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
#include "omap_hwmod_33xx_43xx_common_data.h"
#include <linux/i2c-omap.h>
#include <linux/power/smartreflex.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/omap-dma.h>
#include "l3_3xxx.h"
#include "cm-regbits-34xx.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
#include "serial.h"
{ .role = "dbck", .clk = "omap_32k_fck", },
};
-static struct omap_mmc_dev_attr mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
/* See 35xx errata 2.1.1.128 in SPRZ278F */
-static struct omap_mmc_dev_attr mmc1_pre_es3_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_pre_es3_dev_attr = {
.flags = (OMAP_HSMMC_SUPPORTS_DUAL_VOLT |
OMAP_HSMMC_BROKEN_MULTIBLOCK_READ),
};
};
/* See 35xx errata 2.1.1.128 in SPRZ278F */
-static struct omap_mmc_dev_attr mmc2_pre_es3_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc2_pre_es3_dev_attr = {
.flags = OMAP_HSMMC_BROKEN_MULTIBLOCK_READ,
};
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/power/smartreflex.h>
#include <linux/i2c-omap.h>
#include "prm44xx.h"
#include "prm-regbits-44xx.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
/* Base offset for all OMAP4 interrupts external to MPUSS */
};
/* mmc1 dev_attr */
-static struct omap_mmc_dev_attr mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/power/smartreflex.h>
#include <linux/i2c-omap.h>
#include "cm2_54xx.h"
#include "prm54xx.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
/* Base offset for all OMAP5 interrupts external to MPUSS */
};
/* mmc1 dev_attr */
-static struct omap_mmc_dev_attr mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
#include <linux/io.h>
#include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
#include <linux/power/smartreflex.h>
#include <linux/i2c-omap.h>
#include "cm2_7xx.h"
#include "prm7xx.h"
#include "i2c.h"
-#include "mmc.h"
#include "wd_timer.h"
#include "soc.h"
};
/* mmc1 dev_attr */
-static struct omap_mmc_dev_attr mmc1_dev_attr = {
+static struct omap_hsmmc_dev_attr mmc1_dev_attr = {
.flags = OMAP_HSMMC_SUPPORTS_DUAL_VOLT,
};
#include <linux/spi/spi.h>
#include <linux/usb/atmel_usba_udc.h>
-#include <mach/atmel-mci.h>
+#include <linux/platform_data/mmc-atmel-mci.h>
#include <linux/atmel-mci.h>
#include <asm/io.h>
+++ /dev/null
-#ifndef __MACH_ATMEL_MCI_H
-#define __MACH_ATMEL_MCI_H
-
-#include <linux/platform_data/dma-dw.h>
-
-/**
- * struct mci_dma_data - DMA data for MCI interface
- */
-struct mci_dma_data {
- struct dw_dma_slave sdata;
-};
-
-/* accessor macros */
-#define slave_data_ptr(s) (&(s)->sdata)
-#define find_slave_dev(s) ((s)->sdata.dma_dev)
-
-#endif /* __MACH_ATMEL_MCI_H */
*/
local_irq_save(flags);
local_mcck_disable();
- /*
- * Ummm... Does this make sense at all? Copying the percpu struct
- * and then zapping it one statement later?
- */
- memcpy(&mcck, this_cpu_ptr(&cpu_mcck), sizeof(mcck));
- memset(&mcck, 0, sizeof(struct mcck_struct));
+ mcck = *this_cpu_ptr(&cpu_mcck);
+ memset(this_cpu_ptr(&cpu_mcck), 0, sizeof(mcck));
clear_cpu_flag(CIF_MCCK_PENDING);
local_mcck_enable();
local_irq_restore(flags);
suffix-$(CONFIG_KERNEL_LZO) := lzo
suffix-$(CONFIG_KERNEL_LZ4) := lz4
-RUN_SIZE = $(shell objdump -h vmlinux | \
+RUN_SIZE = $(shell $(OBJDUMP) -h vmlinux | \
perl $(srctree)/arch/x86/tools/calc_run_size.pl)
quiet_cmd_mkpiggy = MKPIGGY $@
cmd_mkpiggy = $(obj)/mkpiggy $< $(RUN_SIZE) > $@ || ( rm -f $@ ; false )
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_NB_F3) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_M10H_F3) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_M30H_NB_F3) },
+ { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_M60H_NB_F3) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_16H_NB_F3) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_16H_M30H_NB_F3) },
{}
static const struct pci_device_id amd_nb_link_ids[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_NB_F4) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_M30H_NB_F4) },
+ { PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_15H_M60H_NB_F4) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_16H_NB_F4) },
{ PCI_DEVICE(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_16H_M30H_NB_F4) },
{}
if (uci->valid && uci->mc)
microcode_ops->apply_microcode(cpu);
+#ifdef CONFIG_X86_64
else if (!uci->mc)
/*
* We might resume and not have applied late microcode but still
* applying patches early on the APs.
*/
load_ucode_ap();
+#endif
}
static struct syscore_ops mc_syscore_ops = {
{
struct blk_integrity *bi = bdev_get_integrity(bio->bi_bdev);
struct blk_integrity_iter iter;
- struct bio_vec *bv;
+ struct bvec_iter bviter;
+ struct bio_vec bv;
struct bio_integrity_payload *bip = bio_integrity(bio);
- unsigned int i, ret = 0;
+ unsigned int ret = 0;
void *prot_buf = page_address(bip->bip_vec->bv_page) +
bip->bip_vec->bv_offset;
iter.seed = bip_get_seed(bip);
iter.prot_buf = prot_buf;
- bio_for_each_segment_all(bv, bio, i) {
- void *kaddr = kmap_atomic(bv->bv_page);
+ bio_for_each_segment(bv, bio, bviter) {
+ void *kaddr = kmap_atomic(bv.bv_page);
- iter.data_buf = kaddr + bv->bv_offset;
- iter.data_size = bv->bv_len;
+ iter.data_buf = kaddr + bv.bv_offset;
+ iter.data_size = bv.bv_len;
ret = proc_fn(&iter);
if (ret) {
return true;
for (i = 0; i < video->attached_count; i++) {
- if (video->attached_array[i].bind_info == device)
+ if ((video->attached_array[i].value.int_val & 0xfff) ==
+ (device->device_id & 0xfff))
return true;
}
{ PCI_VDEVICE(INTEL, 0x8c87), board_ahci }, /* 9 Series RAID */
{ PCI_VDEVICE(INTEL, 0x8c8e), board_ahci }, /* 9 Series RAID */
{ PCI_VDEVICE(INTEL, 0x8c8f), board_ahci }, /* 9 Series RAID */
+ { PCI_VDEVICE(INTEL, 0x9d03), board_ahci }, /* Sunrise Point-LP AHCI */
+ { PCI_VDEVICE(INTEL, 0x9d05), board_ahci }, /* Sunrise Point-LP RAID */
+ { PCI_VDEVICE(INTEL, 0x9d07), board_ahci }, /* Sunrise Point-LP RAID */
{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H AHCI */
{ PCI_VDEVICE(INTEL, 0xa103), board_ahci }, /* Sunrise Point-H RAID */
{ PCI_VDEVICE(INTEL, 0xa105), board_ahci }, /* Sunrise Point-H RAID */
* enabled. https://bugzilla.kernel.org/show_bug.cgi?id=60731
*/
{ PCI_VDEVICE(SAMSUNG, 0x1600), board_ahci_nomsi },
+ { PCI_VDEVICE(SAMSUNG, 0xa800), board_ahci_nomsi },
/* Enmotus */
{ PCI_DEVICE(0x1c44, 0x8000), board_ahci },
host_priv->csr_base = csr_base;
irq = irq_of_parse_and_map(ofdev->dev.of_node, 0);
- if (irq < 0) {
+ if (!irq) {
dev_err(&ofdev->dev, "invalid irq from platform\n");
goto error_exit_with_cleanup;
}
#include <linux/clk-provider.h>
#include <linux/platform_device.h>
#include <linux/mfd/samsung/s2mps11.h>
+#include <linux/mfd/samsung/s2mps13.h>
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s5m8767.h>
#include <linux/mfd/samsung/core.h>
},
};
+static struct clk_init_data s2mps13_clks_init[S2MPS11_CLKS_NUM] = {
+ [S2MPS11_CLK_AP] = {
+ .name = "s2mps13_ap",
+ .ops = &s2mps11_clk_ops,
+ .flags = CLK_IS_ROOT,
+ },
+ [S2MPS11_CLK_CP] = {
+ .name = "s2mps13_cp",
+ .ops = &s2mps11_clk_ops,
+ .flags = CLK_IS_ROOT,
+ },
+ [S2MPS11_CLK_BT] = {
+ .name = "s2mps13_bt",
+ .ops = &s2mps11_clk_ops,
+ .flags = CLK_IS_ROOT,
+ },
+};
+
static struct clk_init_data s2mps14_clks_init[S2MPS11_CLKS_NUM] = {
[S2MPS11_CLK_AP] = {
.name = "s2mps14_ap",
s2mps11_reg = S2MPS11_REG_RTC_CTRL;
clks_init = s2mps11_clks_init;
break;
+ case S2MPS13X:
+ s2mps11_reg = S2MPS13_REG_RTCCTRL;
+ clks_init = s2mps13_clks_init;
+ break;
case S2MPS14X:
s2mps11_reg = S2MPS14_REG_RTCCTRL;
clks_init = s2mps14_clks_init;
static const struct platform_device_id s2mps11_clk_id[] = {
{ "s2mps11-clk", S2MPS11X},
+ { "s2mps13-clk", S2MPS13X},
{ "s2mps14-clk", S2MPS14X},
{ "s5m8767-clk", S5M8767X},
{ },
has been initialized.
config EDAC_MCE_INJ
- tristate "Simple MCE injection interface over /sysfs"
- depends on EDAC_DECODE_MCE
+ tristate "Simple MCE injection interface"
+ depends on EDAC_DECODE_MCE && DEBUG_FS
default n
help
- This is a simple interface to inject MCEs over /sysfs and test
- the MCE decoding code in EDAC.
+ This is a simple debugfs interface to inject MCEs and test different
+ aspects of the MCE handling code.
- This is currently AMD-only.
+ WARNING: Do not even assume this interface is staying stable!
config EDAC_MM_EDAC
tristate "Main Memory EDAC (Error Detection And Correction) reporting"
In doubt, say 'Y'.
config EDAC_AMD64
- tristate "AMD64 (Opteron, Athlon64) K8, F10h"
- depends on EDAC_MM_EDAC && AMD_NB && X86_64 && EDAC_DECODE_MCE
+ tristate "AMD64 (Opteron, Athlon64)"
+ depends on EDAC_MM_EDAC && AMD_NB && EDAC_DECODE_MCE
help
Support for error detection and correction of DRAM ECC errors on
- the AMD64 families of memory controllers (K8 and F10h)
+ the AMD64 families (>= K8) of memory controllers.
config EDAC_AMD64_ERROR_INJECTION
bool "Sysfs HW Error injection facilities"
obj-$(CONFIG_EDAC) := edac_stub.o
obj-$(CONFIG_EDAC_MM_EDAC) += edac_core.o
-edac_core-y := edac_mc.o edac_device.o edac_mc_sysfs.o edac_pci_sysfs.o
+edac_core-y := edac_mc.o edac_device.o edac_mc_sysfs.o
edac_core-y += edac_module.o edac_device_sysfs.o
ifdef CONFIG_PCI
{
edac_dbg(1, "F2x%d90 (DRAM Cfg Low): 0x%08x\n", chan, dclr);
- edac_dbg(1, " DIMM type: %sbuffered; all DIMMs support ECC: %s\n",
- (dclr & BIT(16)) ? "un" : "",
- (dclr & BIT(19)) ? "yes" : "no");
+ if (pvt->dram_type == MEM_LRDDR3) {
+ u32 dcsm = pvt->csels[chan].csmasks[0];
+ /*
+ * It's assumed all LRDIMMs in a DCT are going to be of
+ * same 'type' until proven otherwise. So, use a cs
+ * value of '0' here to get dcsm value.
+ */
+ edac_dbg(1, " LRDIMM %dx rank multiply\n", (dcsm & 0x3));
+ }
+
+ edac_dbg(1, "All DIMMs support ECC:%s\n",
+ (dclr & BIT(19)) ? "yes" : "no");
+
edac_dbg(1, " PAR/ERR parity: %s\n",
(dclr & BIT(8)) ? "enabled" : "disabled");
if (pvt->fam == 0xf && pvt->ext_model < K8_REV_F) {
pvt->csels[0].b_cnt = pvt->csels[1].b_cnt = 8;
pvt->csels[0].m_cnt = pvt->csels[1].m_cnt = 8;
- } else if (pvt->fam == 0x15 && pvt->model >= 0x30) {
+ } else if (pvt->fam == 0x15 && pvt->model == 0x30) {
pvt->csels[0].b_cnt = pvt->csels[1].b_cnt = 4;
pvt->csels[0].m_cnt = pvt->csels[1].m_cnt = 2;
} else {
}
}
-static enum mem_type determine_memory_type(struct amd64_pvt *pvt, int cs)
+static void determine_memory_type(struct amd64_pvt *pvt)
{
- enum mem_type type;
+ u32 dram_ctrl, dcsm;
- /* F15h supports only DDR3 */
- if (pvt->fam >= 0x15)
- type = (pvt->dclr0 & BIT(16)) ? MEM_DDR3 : MEM_RDDR3;
- else if (pvt->fam == 0x10 || pvt->ext_model >= K8_REV_F) {
+ switch (pvt->fam) {
+ case 0xf:
+ if (pvt->ext_model >= K8_REV_F)
+ goto ddr3;
+
+ pvt->dram_type = (pvt->dclr0 & BIT(18)) ? MEM_DDR : MEM_RDDR;
+ return;
+
+ case 0x10:
if (pvt->dchr0 & DDR3_MODE)
- type = (pvt->dclr0 & BIT(16)) ? MEM_DDR3 : MEM_RDDR3;
+ goto ddr3;
+
+ pvt->dram_type = (pvt->dclr0 & BIT(16)) ? MEM_DDR2 : MEM_RDDR2;
+ return;
+
+ case 0x15:
+ if (pvt->model < 0x60)
+ goto ddr3;
+
+ /*
+ * Model 0x60h needs special handling:
+ *
+ * We use a Chip Select value of '0' to obtain dcsm.
+ * Theoretically, it is possible to populate LRDIMMs of different
+ * 'Rank' value on a DCT. But this is not the common case. So,
+ * it's reasonable to assume all DIMMs are going to be of same
+ * 'type' until proven otherwise.
+ */
+ amd64_read_dct_pci_cfg(pvt, 0, DRAM_CONTROL, &dram_ctrl);
+ dcsm = pvt->csels[0].csmasks[0];
+
+ if (((dram_ctrl >> 8) & 0x7) == 0x2)
+ pvt->dram_type = MEM_DDR4;
+ else if (pvt->dclr0 & BIT(16))
+ pvt->dram_type = MEM_DDR3;
+ else if (dcsm & 0x3)
+ pvt->dram_type = MEM_LRDDR3;
else
- type = (pvt->dclr0 & BIT(16)) ? MEM_DDR2 : MEM_RDDR2;
- } else {
- type = (pvt->dclr0 & BIT(18)) ? MEM_DDR : MEM_RDDR;
- }
+ pvt->dram_type = MEM_RDDR3;
- amd64_info("CS%d: %s\n", cs, edac_mem_types[type]);
+ return;
- return type;
+ case 0x16:
+ goto ddr3;
+
+ default:
+ WARN(1, KERN_ERR "%s: Family??? 0x%x\n", __func__, pvt->fam);
+ pvt->dram_type = MEM_EMPTY;
+ }
+ return;
+
+ddr3:
+ pvt->dram_type = (pvt->dclr0 & BIT(16)) ? MEM_DDR3 : MEM_RDDR3;
}
/* Get the number of DCT channels the memory controller is using. */
if (WARN_ON(!nb))
return;
- pci_func = (pvt->model == 0x30) ? PCI_DEVICE_ID_AMD_15H_M30H_NB_F1
- : PCI_DEVICE_ID_AMD_15H_NB_F1;
+ if (pvt->model == 0x60)
+ pci_func = PCI_DEVICE_ID_AMD_15H_M60H_NB_F1;
+ else if (pvt->model == 0x30)
+ pci_func = PCI_DEVICE_ID_AMD_15H_M30H_NB_F1;
+ else
+ pci_func = PCI_DEVICE_ID_AMD_15H_NB_F1;
f1 = pci_get_related_function(nb->misc->vendor, pci_func, nb->misc);
if (WARN_ON(!f1))
}
static int k8_dbam_to_chip_select(struct amd64_pvt *pvt, u8 dct,
- unsigned cs_mode)
+ unsigned cs_mode, int cs_mask_nr)
{
u32 dclr = dct ? pvt->dclr1 : pvt->dclr0;
return cs_size;
}
+static int ddr3_lrdimm_cs_size(unsigned i, unsigned rank_multiply)
+{
+ unsigned shift = 0;
+ int cs_size = 0;
+
+ if (i < 4 || i == 6)
+ cs_size = -1;
+ else if (i == 12)
+ shift = 7;
+ else if (!(i & 0x1))
+ shift = i >> 1;
+ else
+ shift = (i + 1) >> 1;
+
+ if (cs_size != -1)
+ cs_size = rank_multiply * (128 << shift);
+
+ return cs_size;
+}
+
+static int ddr4_cs_size(unsigned i)
+{
+ int cs_size = 0;
+
+ if (i == 0)
+ cs_size = -1;
+ else if (i == 1)
+ cs_size = 1024;
+ else
+ /* Min cs_size = 1G */
+ cs_size = 1024 * (1 << (i >> 1));
+
+ return cs_size;
+}
+
static int f10_dbam_to_chip_select(struct amd64_pvt *pvt, u8 dct,
- unsigned cs_mode)
+ unsigned cs_mode, int cs_mask_nr)
{
u32 dclr = dct ? pvt->dclr1 : pvt->dclr0;
* F15h supports only 64bit DCT interfaces
*/
static int f15_dbam_to_chip_select(struct amd64_pvt *pvt, u8 dct,
- unsigned cs_mode)
+ unsigned cs_mode, int cs_mask_nr)
{
WARN_ON(cs_mode > 12);
return ddr3_cs_size(cs_mode, false);
}
+/* F15h M60h supports DDR4 mapping as well.. */
+static int f15_m60h_dbam_to_chip_select(struct amd64_pvt *pvt, u8 dct,
+ unsigned cs_mode, int cs_mask_nr)
+{
+ int cs_size;
+ u32 dcsm = pvt->csels[dct].csmasks[cs_mask_nr];
+
+ WARN_ON(cs_mode > 12);
+
+ if (pvt->dram_type == MEM_DDR4) {
+ if (cs_mode > 9)
+ return -1;
+
+ cs_size = ddr4_cs_size(cs_mode);
+ } else if (pvt->dram_type == MEM_LRDDR3) {
+ unsigned rank_multiply = dcsm & 0xf;
+
+ if (rank_multiply == 3)
+ rank_multiply = 4;
+ cs_size = ddr3_lrdimm_cs_size(cs_mode, rank_multiply);
+ } else {
+ /* Minimum cs size is 512mb for F15hM60h*/
+ if (cs_mode == 0x1)
+ return -1;
+
+ cs_size = ddr3_cs_size(cs_mode, false);
+ }
+
+ return cs_size;
+}
+
/*
* F16h and F15h model 30h have only limited cs_modes.
*/
static int f16_dbam_to_chip_select(struct amd64_pvt *pvt, u8 dct,
- unsigned cs_mode)
+ unsigned cs_mode, int cs_mask_nr)
{
WARN_ON(cs_mode > 12);
size0 = 0;
if (dcsb[dimm*2] & DCSB_CS_ENABLE)
+ /* For f15m60h, need multiplier for LRDIMM cs_size
+ * calculation. We pass 'dimm' value to the dbam_to_cs
+ * mapper so we can find the multiplier from the
+ * corresponding DCSM.
+ */
size0 = pvt->ops->dbam_to_cs(pvt, ctrl,
- DBAM_DIMM(dimm, dbam));
+ DBAM_DIMM(dimm, dbam),
+ dimm);
size1 = 0;
if (dcsb[dimm*2 + 1] & DCSB_CS_ENABLE)
size1 = pvt->ops->dbam_to_cs(pvt, ctrl,
- DBAM_DIMM(dimm, dbam));
+ DBAM_DIMM(dimm, dbam),
+ dimm);
amd64_info(EDAC_MC ": %d: %5dMB %d: %5dMB\n",
dimm * 2, size0,
.dbam_to_cs = f16_dbam_to_chip_select,
}
},
+ [F15_M60H_CPUS] = {
+ .ctl_name = "F15h_M60h",
+ .f1_id = PCI_DEVICE_ID_AMD_15H_M60H_NB_F1,
+ .f3_id = PCI_DEVICE_ID_AMD_15H_M60H_NB_F3,
+ .ops = {
+ .early_channel_count = f1x_early_channel_count,
+ .map_sysaddr_to_csrow = f1x_map_sysaddr_to_csrow,
+ .dbam_to_cs = f15_m60h_dbam_to_chip_select,
+ }
+ },
[F16_CPUS] = {
.ctl_name = "F16h",
.f1_id = PCI_DEVICE_ID_AMD_16H_NB_F1,
}
pvt->ecc_sym_sz = 4;
+ determine_memory_type(pvt);
+ edac_dbg(1, " DIMM type: %s\n", edac_mem_types[pvt->dram_type]);
if (pvt->fam >= 0x10) {
amd64_read_pci_cfg(pvt->F3, EXT_NB_MCA_CFG, &tmp);
*/
cs_mode = DBAM_DIMM(csrow_nr / 2, dbam);
- nr_pages = pvt->ops->dbam_to_cs(pvt, dct, cs_mode) << (20 - PAGE_SHIFT);
+ nr_pages = pvt->ops->dbam_to_cs(pvt, dct, cs_mode, (csrow_nr / 2))
+ << (20 - PAGE_SHIFT);
edac_dbg(0, "csrow: %d, channel: %d, DBAM idx: %d\n",
csrow_nr, dct, cs_mode);
struct csrow_info *csrow;
struct dimm_info *dimm;
enum edac_type edac_mode;
- enum mem_type mtype;
int i, j, empty = 1;
int nr_pages = 0;
u32 val;
nr_pages += row_dct1_pages;
}
- mtype = determine_memory_type(pvt, i);
-
edac_dbg(1, "Total csrow%d pages: %u\n", i, nr_pages);
/*
for (j = 0; j < pvt->channel_count; j++) {
dimm = csrow->channels[j]->dimm;
- dimm->mtype = mtype;
+ dimm->mtype = pvt->dram_type;
dimm->edac_mode = edac_mode;
}
}
fam_type = &family_types[F15_M30H_CPUS];
pvt->ops = &family_types[F15_M30H_CPUS].ops;
break;
+ } else if (pvt->model == 0x60) {
+ fam_type = &family_types[F15_M60H_CPUS];
+ pvt->ops = &family_types[F15_M60H_CPUS].ops;
+ break;
}
fam_type = &family_types[F15_CPUS];
* inquiry this table to see if this driver is for a given device found.
*/
static const struct pci_device_id amd64_pci_table[] = {
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_K8_NB_MEMCTL,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_10H_NB_DRAM,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_15H_NB_F2,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_15H_M30H_NB_F2,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_16H_NB_F2,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
- {
- .vendor = PCI_VENDOR_ID_AMD,
- .device = PCI_DEVICE_ID_AMD_16H_M30H_NB_F2,
- .subvendor = PCI_ANY_ID,
- .subdevice = PCI_ANY_ID,
- .class = 0,
- .class_mask = 0,
- },
-
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_K8_NB_MEMCTL) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_10H_NB_DRAM) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_15H_NB_F2) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_15H_M30H_NB_F2) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_15H_M60H_NB_F2) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_16H_NB_F2) },
+ { PCI_VDEVICE(AMD, PCI_DEVICE_ID_AMD_16H_M30H_NB_F2) },
{0, }
};
MODULE_DEVICE_TABLE(pci, amd64_pci_table);
goto err_no_instances;
setup_pci_device();
+
+#ifdef CONFIG_X86_32
+ amd64_err("%s on 32-bit is unsupported. USE AT YOUR OWN RISK!\n", EDAC_MOD_STR);
+#endif
+
return 0;
err_no_instances:
/*
* PCI-defined configuration space registers
*/
-#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F1 0x141b
-#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F2 0x141c
#define PCI_DEVICE_ID_AMD_15H_NB_F1 0x1601
#define PCI_DEVICE_ID_AMD_15H_NB_F2 0x1602
+#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F1 0x141b
+#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F2 0x141c
+#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F1 0x1571
+#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F2 0x1572
#define PCI_DEVICE_ID_AMD_16H_NB_F1 0x1531
#define PCI_DEVICE_ID_AMD_16H_NB_F2 0x1532
#define PCI_DEVICE_ID_AMD_16H_M30H_NB_F1 0x1581
#define csrow_enabled(i, dct, pvt) ((pvt)->csels[(dct)].csbases[(i)] & DCSB_CS_ENABLE)
+#define DRAM_CONTROL 0x78
+
#define DBAM0 0x80
#define DBAM1 0x180
F10_CPUS,
F15_CPUS,
F15_M30H_CPUS,
+ F15_M60H_CPUS,
F16_CPUS,
F16_M30H_CPUS,
NUM_FAMILIES,
/* place to store error injection parameters prior to issue */
struct error_injection injection;
+
+ /* cache the dram_type */
+ enum mem_type dram_type;
};
enum err_codes {
int (*early_channel_count) (struct amd64_pvt *pvt);
void (*map_sysaddr_to_csrow) (struct mem_ctl_info *mci, u64 sys_addr,
struct err_info *);
- int (*dbam_to_cs) (struct amd64_pvt *pvt, u8 dct, unsigned cs_mode);
+ int (*dbam_to_cs) (struct amd64_pvt *pvt, u8 dct,
+ unsigned cs_mode, int cs_mask_nr);
};
struct amd64_family_type {
#endif /* CONFIG_EDAC_DEBUG */
-/*
- * keep those in sync with the enum mem_type
- */
const char * const edac_mem_types[] = {
- "Empty csrow",
- "Reserved csrow type",
- "Unknown csrow type",
- "Fast page mode RAM",
- "Extended data out RAM",
- "Burst Extended data out RAM",
- "Single data rate SDRAM",
- "Registered single data rate SDRAM",
- "Double data rate SDRAM",
- "Registered Double data rate SDRAM",
- "Rambus DRAM",
- "Unbuffered DDR2 RAM",
- "Fully buffered DDR2",
- "Registered DDR2 RAM",
- "Rambus XDR",
- "Unbuffered DDR3 RAM",
- "Registered DDR3 RAM",
+ [MEM_EMPTY] = "Empty csrow",
+ [MEM_RESERVED] = "Reserved csrow type",
+ [MEM_UNKNOWN] = "Unknown csrow type",
+ [MEM_FPM] = "Fast page mode RAM",
+ [MEM_EDO] = "Extended data out RAM",
+ [MEM_BEDO] = "Burst Extended data out RAM",
+ [MEM_SDR] = "Single data rate SDRAM",
+ [MEM_RDR] = "Registered single data rate SDRAM",
+ [MEM_DDR] = "Double data rate SDRAM",
+ [MEM_RDDR] = "Registered Double data rate SDRAM",
+ [MEM_RMBS] = "Rambus DRAM",
+ [MEM_DDR2] = "Unbuffered DDR2 RAM",
+ [MEM_FB_DDR2] = "Fully buffered DDR2",
+ [MEM_RDDR2] = "Registered DDR2 RAM",
+ [MEM_XDR] = "Rambus XDR",
+ [MEM_DDR3] = "Unbuffered DDR3 RAM",
+ [MEM_RDDR3] = "Registered DDR3 RAM",
+ [MEM_LRDDR3] = "Load-Reduced DDR3 RAM",
+ [MEM_DDR4] = "Unbuffered DDR4 RAM",
+ [MEM_RDDR4] = "Registered DDR4 RAM",
};
EXPORT_SYMBOL_GPL(edac_mem_types);
#include "edac_core.h"
#include "edac_module.h"
-/* Turn off this whole feature if PCI is not configured */
-#ifdef CONFIG_PCI
-
#define EDAC_PCI_SYMLINK "device"
/* data variables exported via sysfs */
module_param(edac_pci_panic_on_pe, int, 0644);
MODULE_PARM_DESC(edac_pci_panic_on_pe,
"Panic on PCI Bus Parity error: 0=off 1=on");
-
-#endif /* CONFIG_PCI */
/* Generate the trace event */
grain_bits = fls_long(e->grain);
- sprintf(pvt->detail_location, "APEI location: %s %s",
- e->location, e->other_detail);
+ snprintf(pvt->detail_location, sizeof(pvt->detail_location),
+ "APEI location: %s %s", e->location, e->other_detail);
trace_mc_event(type, e->msg, e->label, e->error_count,
mci->mc_idx, e->top_layer, e->mid_layer, e->low_layer,
PAGES_TO_MiB(e->page_frame_number) | e->offset_in_page,
pci_unregister_driver(&i3000_driver);
fail0:
- if (mci_pdev)
- pci_dev_put(mci_pdev);
+ pci_dev_put(mci_pdev);
return pci_rc;
}
pci_unregister_driver(&i3200_driver);
fail0:
- if (mci_pdev)
- pci_dev_put(mci_pdev);
+ pci_dev_put(mci_pdev);
return pci_rc;
}
if (!i82443bxgx_registered)
i82443bxgx_edacmc_remove_one(mci_pdev);
- if (mci_pdev)
- pci_dev_put(mci_pdev);
+ pci_dev_put(mci_pdev);
}
module_init(i82443bxgx_edacmc_init);
"Retire status queue"
};
+static const char * const mc6_mce_desc[] = {
+ "Hardware Assertion",
+ "Free List",
+ "Physical Register File",
+ "Retire Queue",
+ "Scheduler table",
+ "Status Register File",
+};
+
static bool f12h_mc0_mce(u16 ec, u8 xec)
{
bool ret = false;
pr_cont(": %s error in the L2 cache tags.\n", R4_MSG(ec));
else if (xec == 0x0) {
if (TLB_ERROR(ec))
- pr_cont(": %s error in a Page Descriptor Cache or "
- "Guest TLB.\n", TT_MSG(ec));
+ pr_cont("%s error in a Page Descriptor Cache or Guest TLB.\n",
+ TT_MSG(ec));
else if (BUS_ERROR(ec))
pr_cont(": %s/ECC error in data read from NB: %s.\n",
R4_MSG(ec), PP_MSG(ec));
pr_emerg(HW_ERR "MC6 Error: ");
- switch (xec) {
- case 0x0:
- pr_cont("Hardware Assertion");
- break;
-
- case 0x1:
- pr_cont("Free List");
- break;
-
- case 0x2:
- pr_cont("Physical Register File");
- break;
-
- case 0x3:
- pr_cont("Retire Queue");
- break;
-
- case 0x4:
- pr_cont("Scheduler table");
- break;
-
- case 0x5:
- pr_cont("Status Register File");
- break;
-
- default:
+ if (xec > 0x5)
goto wrong_mc6_mce;
- break;
- }
-
- pr_cont(" parity error.\n");
+ pr_cont("%s parity error.\n", mc6_mce_desc[xec]);
return;
wrong_mc6_mce:
pr_cont("]: 0x%016llx\n", m->status);
if (m->status & MCI_STATUS_ADDRV)
- pr_emerg(HW_ERR "MC%d_ADDR: 0x%016llx\n", m->bank, m->addr);
+ pr_emerg(HW_ERR "MC%d Error Address: 0x%016llx\n", m->bank, m->addr);
if (!fam_ops)
goto err_code;
/*
- * A simple MCE injection facility for testing the MCE decoding code. This
- * driver should be built as module so that it can be loaded on production
- * kernels for testing purposes.
+ * A simple MCE injection facility for testing different aspects of the RAS
+ * code. This driver should be built as module so that it can be loaded
+ * on production kernels for testing purposes.
*
* This file may be distributed under the terms of the GNU General Public
* License version 2.
*
- * Copyright (c) 2010: Borislav Petkov <bp@alien8.de>
+ * Copyright (c) 2010-14: Borislav Petkov <bp@alien8.de>
* Advanced Micro Devices Inc.
*/
#include <linux/kobject.h>
+#include <linux/debugfs.h>
#include <linux/device.h>
-#include <linux/edac.h>
#include <linux/module.h>
+#include <linux/cpu.h>
#include <asm/mce.h>
#include "mce_amd.h"
-struct edac_mce_attr {
- struct attribute attr;
- ssize_t (*show) (struct kobject *kobj, struct edac_mce_attr *attr, char *buf);
- ssize_t (*store)(struct kobject *kobj, struct edac_mce_attr *attr,
- const char *buf, size_t count);
-};
-
-#define EDAC_MCE_ATTR(_name, _mode, _show, _store) \
-static struct edac_mce_attr mce_attr_##_name = __ATTR(_name, _mode, _show, _store)
-
-static struct kobject *mce_kobj;
-
/*
* Collect all the MCi_XXX settings
*/
static struct mce i_mce;
+static struct dentry *dfs_inj;
-#define MCE_INJECT_STORE(reg) \
-static ssize_t edac_inject_##reg##_store(struct kobject *kobj, \
- struct edac_mce_attr *attr, \
- const char *data, size_t count)\
+#define MCE_INJECT_SET(reg) \
+static int inj_##reg##_set(void *data, u64 val) \
{ \
- int ret = 0; \
- unsigned long value; \
- \
- ret = kstrtoul(data, 16, &value); \
- if (ret < 0) \
- printk(KERN_ERR "Error writing MCE " #reg " field.\n"); \
+ struct mce *m = (struct mce *)data; \
\
- i_mce.reg = value; \
- \
- return count; \
+ m->reg = val; \
+ return 0; \
}
-MCE_INJECT_STORE(status);
-MCE_INJECT_STORE(misc);
-MCE_INJECT_STORE(addr);
+MCE_INJECT_SET(status);
+MCE_INJECT_SET(misc);
+MCE_INJECT_SET(addr);
-#define MCE_INJECT_SHOW(reg) \
-static ssize_t edac_inject_##reg##_show(struct kobject *kobj, \
- struct edac_mce_attr *attr, \
- char *buf) \
+#define MCE_INJECT_GET(reg) \
+static int inj_##reg##_get(void *data, u64 *val) \
{ \
- return sprintf(buf, "0x%016llx\n", i_mce.reg); \
+ struct mce *m = (struct mce *)data; \
+ \
+ *val = m->reg; \
+ return 0; \
}
-MCE_INJECT_SHOW(status);
-MCE_INJECT_SHOW(misc);
-MCE_INJECT_SHOW(addr);
+MCE_INJECT_GET(status);
+MCE_INJECT_GET(misc);
+MCE_INJECT_GET(addr);
-EDAC_MCE_ATTR(status, 0644, edac_inject_status_show, edac_inject_status_store);
-EDAC_MCE_ATTR(misc, 0644, edac_inject_misc_show, edac_inject_misc_store);
-EDAC_MCE_ATTR(addr, 0644, edac_inject_addr_show, edac_inject_addr_store);
+DEFINE_SIMPLE_ATTRIBUTE(status_fops, inj_status_get, inj_status_set, "%llx\n");
+DEFINE_SIMPLE_ATTRIBUTE(misc_fops, inj_misc_get, inj_misc_set, "%llx\n");
+DEFINE_SIMPLE_ATTRIBUTE(addr_fops, inj_addr_get, inj_addr_set, "%llx\n");
/*
- * This denotes into which bank we're injecting and triggers
- * the injection, at the same time.
+ * Caller needs to be make sure this cpu doesn't disappear
+ * from under us, i.e.: get_cpu/put_cpu.
*/
-static ssize_t edac_inject_bank_store(struct kobject *kobj,
- struct edac_mce_attr *attr,
- const char *data, size_t count)
+static int toggle_hw_mce_inject(unsigned int cpu, bool enable)
{
- int ret = 0;
- unsigned long value;
+ u32 l, h;
+ int err;
- ret = kstrtoul(data, 10, &value);
- if (ret < 0) {
- printk(KERN_ERR "Invalid bank value!\n");
- return -EINVAL;
+ err = rdmsr_on_cpu(cpu, MSR_K7_HWCR, &l, &h);
+ if (err) {
+ pr_err("%s: error reading HWCR\n", __func__);
+ return err;
}
- if (value > 5)
- if (boot_cpu_data.x86 != 0x15 || value > 6) {
- printk(KERN_ERR "Non-existent MCE bank: %lu\n", value);
- return -EINVAL;
- }
+ enable ? (l |= BIT(18)) : (l &= ~BIT(18));
- i_mce.bank = value;
+ err = wrmsr_on_cpu(cpu, MSR_K7_HWCR, l, h);
+ if (err)
+ pr_err("%s: error writing HWCR\n", __func__);
- amd_decode_mce(NULL, 0, &i_mce);
+ return err;
+}
- return count;
+static int flags_get(void *data, u64 *val)
+{
+ struct mce *m = (struct mce *)data;
+
+ *val = m->inject_flags;
+
+ return 0;
}
-static ssize_t edac_inject_bank_show(struct kobject *kobj,
- struct edac_mce_attr *attr, char *buf)
+static int flags_set(void *data, u64 val)
{
- return sprintf(buf, "%d\n", i_mce.bank);
+ struct mce *m = (struct mce *)data;
+
+ m->inject_flags = (u8)val;
+ return 0;
}
-EDAC_MCE_ATTR(bank, 0644, edac_inject_bank_show, edac_inject_bank_store);
+DEFINE_SIMPLE_ATTRIBUTE(flags_fops, flags_get, flags_set, "%llu\n");
-static struct edac_mce_attr *sysfs_attrs[] = { &mce_attr_status, &mce_attr_misc,
- &mce_attr_addr, &mce_attr_bank
-};
+/*
+ * On which CPU to inject?
+ */
+MCE_INJECT_GET(extcpu);
-static int __init edac_init_mce_inject(void)
+static int inj_extcpu_set(void *data, u64 val)
{
- struct bus_type *edac_subsys = NULL;
- int i, err = 0;
+ struct mce *m = (struct mce *)data;
- edac_subsys = edac_get_sysfs_subsys();
- if (!edac_subsys)
+ if (val >= nr_cpu_ids || !cpu_online(val)) {
+ pr_err("%s: Invalid CPU: %llu\n", __func__, val);
return -EINVAL;
+ }
+ m->extcpu = val;
+ return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(extcpu_fops, inj_extcpu_get, inj_extcpu_set, "%llu\n");
- mce_kobj = kobject_create_and_add("mce", &edac_subsys->dev_root->kobj);
- if (!mce_kobj) {
- printk(KERN_ERR "Error creating a mce kset.\n");
- err = -ENOMEM;
- goto err_mce_kobj;
+static void trigger_mce(void *info)
+{
+ asm volatile("int $18");
+}
+
+static void do_inject(void)
+{
+ u64 mcg_status = 0;
+ unsigned int cpu = i_mce.extcpu;
+ u8 b = i_mce.bank;
+
+ if (!(i_mce.inject_flags & MCJ_EXCEPTION)) {
+ amd_decode_mce(NULL, 0, &i_mce);
+ return;
}
- for (i = 0; i < ARRAY_SIZE(sysfs_attrs); i++) {
- err = sysfs_create_file(mce_kobj, &sysfs_attrs[i]->attr);
- if (err) {
- printk(KERN_ERR "Error creating %s in sysfs.\n",
- sysfs_attrs[i]->attr.name);
- goto err_sysfs_create;
+ get_online_cpus();
+ if (!cpu_online(cpu))
+ goto err;
+
+ /* prep MCE global settings for the injection */
+ mcg_status = MCG_STATUS_MCIP | MCG_STATUS_EIPV;
+
+ if (!(i_mce.status & MCI_STATUS_PCC))
+ mcg_status |= MCG_STATUS_RIPV;
+
+ toggle_hw_mce_inject(cpu, true);
+
+ wrmsr_on_cpu(cpu, MSR_IA32_MCG_STATUS,
+ (u32)mcg_status, (u32)(mcg_status >> 32));
+
+ wrmsr_on_cpu(cpu, MSR_IA32_MCx_STATUS(b),
+ (u32)i_mce.status, (u32)(i_mce.status >> 32));
+
+ wrmsr_on_cpu(cpu, MSR_IA32_MCx_ADDR(b),
+ (u32)i_mce.addr, (u32)(i_mce.addr >> 32));
+
+ wrmsr_on_cpu(cpu, MSR_IA32_MCx_MISC(b),
+ (u32)i_mce.misc, (u32)(i_mce.misc >> 32));
+
+ toggle_hw_mce_inject(cpu, false);
+
+ smp_call_function_single(cpu, trigger_mce, NULL, 0);
+
+err:
+ put_online_cpus();
+
+}
+
+/*
+ * This denotes into which bank we're injecting and triggers
+ * the injection, at the same time.
+ */
+static int inj_bank_set(void *data, u64 val)
+{
+ struct mce *m = (struct mce *)data;
+
+ if (val > 5) {
+ if (boot_cpu_data.x86 != 0x15 || val > 6) {
+ pr_err("Non-existent MCE bank: %llu\n", val);
+ return -EINVAL;
}
}
- return 0;
-err_sysfs_create:
- while (--i >= 0)
- sysfs_remove_file(mce_kobj, &sysfs_attrs[i]->attr);
+ m->bank = val;
+ do_inject();
- kobject_del(mce_kobj);
+ return 0;
+}
-err_mce_kobj:
- edac_put_sysfs_subsys();
+static int inj_bank_get(void *data, u64 *val)
+{
+ struct mce *m = (struct mce *)data;
- return err;
+ *val = m->bank;
+ return 0;
}
-static void __exit edac_exit_mce_inject(void)
+DEFINE_SIMPLE_ATTRIBUTE(bank_fops, inj_bank_get, inj_bank_set, "%llu\n");
+
+struct dfs_node {
+ char *name;
+ struct dentry *d;
+ const struct file_operations *fops;
+} dfs_fls[] = {
+ { .name = "status", .fops = &status_fops },
+ { .name = "misc", .fops = &misc_fops },
+ { .name = "addr", .fops = &addr_fops },
+ { .name = "bank", .fops = &bank_fops },
+ { .name = "flags", .fops = &flags_fops },
+ { .name = "cpu", .fops = &extcpu_fops },
+};
+
+static int __init init_mce_inject(void)
{
int i;
- for (i = 0; i < ARRAY_SIZE(sysfs_attrs); i++)
- sysfs_remove_file(mce_kobj, &sysfs_attrs[i]->attr);
+ dfs_inj = debugfs_create_dir("mce-inject", NULL);
+ if (!dfs_inj)
+ return -EINVAL;
+
+ for (i = 0; i < ARRAY_SIZE(dfs_fls); i++) {
+ dfs_fls[i].d = debugfs_create_file(dfs_fls[i].name,
+ S_IRUSR | S_IWUSR,
+ dfs_inj,
+ &i_mce,
+ dfs_fls[i].fops);
+
+ if (!dfs_fls[i].d)
+ goto err_dfs_add;
+ }
+
+ return 0;
+
+err_dfs_add:
+ while (--i >= 0)
+ debugfs_remove(dfs_fls[i].d);
- kobject_del(mce_kobj);
+ debugfs_remove(dfs_inj);
+ dfs_inj = NULL;
- edac_put_sysfs_subsys();
+ return -ENOMEM;
}
-module_init(edac_init_mce_inject);
-module_exit(edac_exit_mce_inject);
+static void __exit exit_mce_inject(void)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(dfs_fls); i++)
+ debugfs_remove(dfs_fls[i].d);
+
+ memset(&dfs_fls, 0, sizeof(dfs_fls));
+
+ debugfs_remove(dfs_inj);
+ dfs_inj = NULL;
+}
+module_init(init_mce_inject);
+module_exit(exit_mce_inject);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Borislav Petkov <bp@alien8.de>");
MODULE_AUTHOR("AMD Inc.");
-MODULE_DESCRIPTION("MCE injection facility for testing MCE decoding");
+MODULE_DESCRIPTION("MCE injection facility for RAS testing");
res = devm_request_irq(&pdev->dev,
pdata->irq,
mv64x60_pci_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] PCI err",
pci);
if (res < 0) {
res = devm_request_irq(&pdev->dev,
pdata->irq,
mv64x60_sram_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] SRAM err",
edac_dev);
if (res < 0) {
res = devm_request_irq(&pdev->dev,
pdata->irq,
mv64x60_cpu_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] CPU err",
edac_dev);
if (res < 0) {
res = devm_request_irq(&pdev->dev,
pdata->irq,
mv64x60_mc_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] MC err",
mci);
if (res < 0) {
status = request_irq(ded_irq,
ppc4xx_edac_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] MC ECCDED",
mci);
status = request_irq(sec_irq,
ppc4xx_edac_isr,
- IRQF_DISABLED,
+ 0,
"[EDAC] MC ECCSEC",
mci);
pci_unregister_driver(&x38_driver);
fail0:
- if (mci_pdev)
- pci_dev_put(mci_pdev);
+ pci_dev_put(mci_pdev);
return pci_rc;
}
River Tech's viperboard.h for detailed meaning
of the module parameters.
+config GPIO_DLN2
+ tristate "Diolan DLN2 GPIO support"
+ depends on MFD_DLN2
+ select GPIOLIB_IRQCHIP
+
+ help
+ Select this option to enable GPIO driver for the Diolan DLN2
+ board.
+
+ This driver can also be built as a module. If so, the module
+ will be called gpio-dln2.
+
endif
obj-$(CONFIG_GPIO_DA9052) += gpio-da9052.o
obj-$(CONFIG_GPIO_DA9055) += gpio-da9055.o
obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o
+obj-$(CONFIG_GPIO_DLN2) += gpio-dln2.o
obj-$(CONFIG_GPIO_DWAPB) += gpio-dwapb.o
obj-$(CONFIG_GPIO_EM) += gpio-em.o
obj-$(CONFIG_GPIO_EP93XX) += gpio-ep93xx.o
--- /dev/null
+/*
+ * Driver for the Diolan DLN-2 USB-GPIO adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/gpio.h>
+#include <linux/gpio/driver.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_GPIO_ID 0x01
+
+#define DLN2_GPIO_GET_PIN_COUNT DLN2_CMD(0x01, DLN2_GPIO_ID)
+#define DLN2_GPIO_SET_DEBOUNCE DLN2_CMD(0x04, DLN2_GPIO_ID)
+#define DLN2_GPIO_GET_DEBOUNCE DLN2_CMD(0x05, DLN2_GPIO_ID)
+#define DLN2_GPIO_PORT_GET_VAL DLN2_CMD(0x06, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_VAL DLN2_CMD(0x0B, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_OUT_VAL DLN2_CMD(0x0C, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_OUT_VAL DLN2_CMD(0x0D, DLN2_GPIO_ID)
+#define DLN2_GPIO_CONDITION_MET_EV DLN2_CMD(0x0F, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_ENABLE DLN2_CMD(0x10, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_DISABLE DLN2_CMD(0x11, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_DIRECTION DLN2_CMD(0x13, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_DIRECTION DLN2_CMD(0x14, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_SET_EVENT_CFG DLN2_CMD(0x1E, DLN2_GPIO_ID)
+#define DLN2_GPIO_PIN_GET_EVENT_CFG DLN2_CMD(0x1F, DLN2_GPIO_ID)
+
+#define DLN2_GPIO_EVENT_NONE 0
+#define DLN2_GPIO_EVENT_CHANGE 1
+#define DLN2_GPIO_EVENT_LVL_HIGH 2
+#define DLN2_GPIO_EVENT_LVL_LOW 3
+#define DLN2_GPIO_EVENT_CHANGE_RISING 0x11
+#define DLN2_GPIO_EVENT_CHANGE_FALLING 0x21
+#define DLN2_GPIO_EVENT_MASK 0x0F
+
+#define DLN2_GPIO_MAX_PINS 32
+
+struct dln2_irq_work {
+ struct work_struct work;
+ struct dln2_gpio *dln2;
+ int pin;
+ int type;
+};
+
+struct dln2_gpio {
+ struct platform_device *pdev;
+ struct gpio_chip gpio;
+
+ /*
+ * Cache pin direction to save us one transfer, since the hardware has
+ * separate commands to read the in and out values.
+ */
+ DECLARE_BITMAP(output_enabled, DLN2_GPIO_MAX_PINS);
+
+ DECLARE_BITMAP(irqs_masked, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_enabled, DLN2_GPIO_MAX_PINS);
+ DECLARE_BITMAP(irqs_pending, DLN2_GPIO_MAX_PINS);
+ struct dln2_irq_work *irq_work;
+};
+
+struct dln2_gpio_pin {
+ __le16 pin;
+};
+
+struct dln2_gpio_pin_val {
+ __le16 pin __packed;
+ u8 value;
+};
+
+static int dln2_gpio_get_pin_count(struct platform_device *pdev)
+{
+ int ret;
+ __le16 count;
+ int len = sizeof(count);
+
+ ret = dln2_transfer_rx(pdev, DLN2_GPIO_GET_PIN_COUNT, &count, &len);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(count))
+ return -EPROTO;
+
+ return le16_to_cpu(count);
+}
+
+static int dln2_gpio_pin_cmd(struct dln2_gpio *dln2, int cmd, unsigned pin)
+{
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+
+ return dln2_transfer_tx(dln2->pdev, cmd, &req, sizeof(req));
+}
+
+static int dln2_gpio_pin_val(struct dln2_gpio *dln2, int cmd, unsigned int pin)
+{
+ int ret;
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(pin),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+
+ ret = dln2_transfer(dln2->pdev, cmd, &req, sizeof(req), &rsp, &len);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin)
+ return -EPROTO;
+
+ return rsp.value;
+}
+
+static int dln2_gpio_pin_get_in_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static int dln2_gpio_pin_get_out_val(struct dln2_gpio *dln2, unsigned int pin)
+{
+ int ret;
+
+ ret = dln2_gpio_pin_val(dln2, DLN2_GPIO_PIN_GET_OUT_VAL, pin);
+ if (ret < 0)
+ return ret;
+ return !!ret;
+}
+
+static void dln2_gpio_pin_set_out_val(struct dln2_gpio *dln2,
+ unsigned int pin, int value)
+{
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(pin),
+ .value = value,
+ };
+
+ dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_OUT_VAL, &req,
+ sizeof(req));
+}
+
+#define DLN2_GPIO_DIRECTION_IN 0
+#define DLN2_GPIO_DIRECTION_OUT 1
+
+static int dln2_gpio_request(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin req = {
+ .pin = cpu_to_le16(offset),
+ };
+ struct dln2_gpio_pin_val rsp;
+ int len = sizeof(rsp);
+ int ret;
+
+ ret = dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_ENABLE, offset);
+ if (ret < 0)
+ return ret;
+
+ /* cache the pin direction */
+ ret = dln2_transfer(dln2->pdev, DLN2_GPIO_PIN_GET_DIRECTION,
+ &req, sizeof(req), &rsp, &len);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(rsp) || req.pin != rsp.pin) {
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+ switch (rsp.value) {
+ case DLN2_GPIO_DIRECTION_IN:
+ clear_bit(offset, dln2->output_enabled);
+ return 0;
+ case DLN2_GPIO_DIRECTION_OUT:
+ set_bit(offset, dln2->output_enabled);
+ return 0;
+ default:
+ ret = -EPROTO;
+ goto out_disable;
+ }
+
+out_disable:
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+ return ret;
+}
+
+static void dln2_gpio_free(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_cmd(dln2, DLN2_GPIO_PIN_DISABLE, offset);
+}
+
+static int dln2_gpio_get_direction(struct gpio_chip *chip, unsigned offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ if (test_bit(offset, dln2->output_enabled))
+ return GPIOF_DIR_OUT;
+
+ return GPIOF_DIR_IN;
+}
+
+static int dln2_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ int dir;
+
+ dir = dln2_gpio_get_direction(chip, offset);
+ if (dir < 0)
+ return dir;
+
+ if (dir == GPIOF_DIR_IN)
+ return dln2_gpio_pin_get_in_val(dln2, offset);
+
+ return dln2_gpio_pin_get_out_val(dln2, offset);
+}
+
+static void dln2_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+
+ dln2_gpio_pin_set_out_val(dln2, offset, value);
+}
+
+static int dln2_gpio_set_direction(struct gpio_chip *chip, unsigned offset,
+ unsigned dir)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ struct dln2_gpio_pin_val req = {
+ .pin = cpu_to_le16(offset),
+ .value = dir,
+ };
+ int ret;
+
+ ret = dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_DIRECTION,
+ &req, sizeof(req));
+ if (ret < 0)
+ return ret;
+
+ if (dir == DLN2_GPIO_DIRECTION_OUT)
+ set_bit(offset, dln2->output_enabled);
+ else
+ clear_bit(offset, dln2->output_enabled);
+
+ return ret;
+}
+
+static int dln2_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_IN);
+}
+
+static int dln2_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ return dln2_gpio_set_direction(chip, offset, DLN2_GPIO_DIRECTION_OUT);
+}
+
+static int dln2_gpio_set_debounce(struct gpio_chip *chip, unsigned offset,
+ unsigned debounce)
+{
+ struct dln2_gpio *dln2 = container_of(chip, struct dln2_gpio, gpio);
+ __le32 duration = cpu_to_le32(debounce);
+
+ return dln2_transfer_tx(dln2->pdev, DLN2_GPIO_SET_DEBOUNCE,
+ &duration, sizeof(duration));
+}
+
+static int dln2_gpio_set_event_cfg(struct dln2_gpio *dln2, unsigned pin,
+ unsigned type, unsigned period)
+{
+ struct {
+ __le16 pin;
+ u8 type;
+ __le16 period;
+ } __packed req = {
+ .pin = cpu_to_le16(pin),
+ .type = type,
+ .period = cpu_to_le16(period),
+ };
+
+ return dln2_transfer_tx(dln2->pdev, DLN2_GPIO_PIN_SET_EVENT_CFG,
+ &req, sizeof(req));
+}
+
+static void dln2_irq_work(struct work_struct *w)
+{
+ struct dln2_irq_work *iw = container_of(w, struct dln2_irq_work, work);
+ struct dln2_gpio *dln2 = iw->dln2;
+ u8 type = iw->type & DLN2_GPIO_EVENT_MASK;
+
+ if (test_bit(iw->pin, dln2->irqs_enabled))
+ dln2_gpio_set_event_cfg(dln2, iw->pin, type, 0);
+ else
+ dln2_gpio_set_event_cfg(dln2, iw->pin, DLN2_GPIO_EVENT_NONE, 0);
+}
+
+static void dln2_irq_enable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_disable(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ clear_bit(pin, dln2->irqs_enabled);
+ schedule_work(&dln2->irq_work[pin].work);
+}
+
+static void dln2_irq_mask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ set_bit(pin, dln2->irqs_masked);
+}
+
+static void dln2_irq_unmask(struct irq_data *irqd)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ struct device *dev = dln2->gpio.dev;
+ int pin = irqd_to_hwirq(irqd);
+
+ if (test_and_clear_bit(pin, dln2->irqs_pending)) {
+ int irq;
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_irq_set_type(struct irq_data *irqd, unsigned type)
+{
+ struct gpio_chip *gc = irq_data_get_irq_chip_data(irqd);
+ struct dln2_gpio *dln2 = container_of(gc, struct dln2_gpio, gpio);
+ int pin = irqd_to_hwirq(irqd);
+
+ switch (type) {
+ case IRQ_TYPE_LEVEL_HIGH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_HIGH;
+ break;
+ case IRQ_TYPE_LEVEL_LOW:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_LVL_LOW;
+ break;
+ case IRQ_TYPE_EDGE_BOTH:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE;
+ break;
+ case IRQ_TYPE_EDGE_RISING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_RISING;
+ break;
+ case IRQ_TYPE_EDGE_FALLING:
+ dln2->irq_work[pin].type = DLN2_GPIO_EVENT_CHANGE_FALLING;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static struct irq_chip dln2_gpio_irqchip = {
+ .name = "dln2-irq",
+ .irq_enable = dln2_irq_enable,
+ .irq_disable = dln2_irq_disable,
+ .irq_mask = dln2_irq_mask,
+ .irq_unmask = dln2_irq_unmask,
+ .irq_set_type = dln2_irq_set_type,
+};
+
+static void dln2_gpio_event(struct platform_device *pdev, u16 echo,
+ const void *data, int len)
+{
+ int pin, irq;
+ const struct {
+ __le16 count;
+ __u8 type;
+ __le16 pin;
+ __u8 value;
+ } __packed *event = data;
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+
+ if (len < sizeof(*event)) {
+ dev_err(dln2->gpio.dev, "short event message\n");
+ return;
+ }
+
+ pin = le16_to_cpu(event->pin);
+ if (pin >= dln2->gpio.ngpio) {
+ dev_err(dln2->gpio.dev, "out of bounds pin %d\n", pin);
+ return;
+ }
+
+ irq = irq_find_mapping(dln2->gpio.irqdomain, pin);
+ if (!irq) {
+ dev_err(dln2->gpio.dev, "pin %d not mapped to IRQ\n", pin);
+ return;
+ }
+
+ if (!test_bit(pin, dln2->irqs_enabled))
+ return;
+ if (test_bit(pin, dln2->irqs_masked)) {
+ set_bit(pin, dln2->irqs_pending);
+ return;
+ }
+
+ switch (dln2->irq_work[pin].type) {
+ case DLN2_GPIO_EVENT_CHANGE_RISING:
+ if (event->value)
+ generic_handle_irq(irq);
+ break;
+ case DLN2_GPIO_EVENT_CHANGE_FALLING:
+ if (!event->value)
+ generic_handle_irq(irq);
+ break;
+ default:
+ generic_handle_irq(irq);
+ }
+}
+
+static int dln2_gpio_probe(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2;
+ struct device *dev = &pdev->dev;
+ int pins;
+ int i, ret;
+
+ pins = dln2_gpio_get_pin_count(pdev);
+ if (pins < 0) {
+ dev_err(dev, "failed to get pin count: %d\n", pins);
+ return pins;
+ }
+ if (pins > DLN2_GPIO_MAX_PINS) {
+ pins = DLN2_GPIO_MAX_PINS;
+ dev_warn(dev, "clamping pins to %d\n", DLN2_GPIO_MAX_PINS);
+ }
+
+ dln2 = devm_kzalloc(&pdev->dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->irq_work = devm_kcalloc(&pdev->dev, pins,
+ sizeof(struct dln2_irq_work), GFP_KERNEL);
+ if (!dln2->irq_work)
+ return -ENOMEM;
+ for (i = 0; i < pins; i++) {
+ INIT_WORK(&dln2->irq_work[i].work, dln2_irq_work);
+ dln2->irq_work[i].pin = i;
+ dln2->irq_work[i].dln2 = dln2;
+ }
+
+ dln2->pdev = pdev;
+
+ dln2->gpio.label = "dln2";
+ dln2->gpio.dev = dev;
+ dln2->gpio.owner = THIS_MODULE;
+ dln2->gpio.base = -1;
+ dln2->gpio.ngpio = pins;
+ dln2->gpio.exported = true;
+ dln2->gpio.can_sleep = true;
+ dln2->gpio.irq_not_threaded = true;
+ dln2->gpio.set = dln2_gpio_set;
+ dln2->gpio.get = dln2_gpio_get;
+ dln2->gpio.request = dln2_gpio_request;
+ dln2->gpio.free = dln2_gpio_free;
+ dln2->gpio.get_direction = dln2_gpio_get_direction;
+ dln2->gpio.direction_input = dln2_gpio_direction_input;
+ dln2->gpio.direction_output = dln2_gpio_direction_output;
+ dln2->gpio.set_debounce = dln2_gpio_set_debounce;
+
+ platform_set_drvdata(pdev, dln2);
+
+ ret = gpiochip_add(&dln2->gpio);
+ if (ret < 0) {
+ dev_err(dev, "failed to add gpio chip: %d\n", ret);
+ goto out;
+ }
+
+ ret = gpiochip_irqchip_add(&dln2->gpio, &dln2_gpio_irqchip, 0,
+ handle_simple_irq, IRQ_TYPE_NONE);
+ if (ret < 0) {
+ dev_err(dev, "failed to add irq chip: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ ret = dln2_register_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV,
+ dln2_gpio_event);
+ if (ret) {
+ dev_err(dev, "failed to register event cb: %d\n", ret);
+ goto out_gpiochip_remove;
+ }
+
+ return 0;
+
+out_gpiochip_remove:
+ gpiochip_remove(&dln2->gpio);
+out:
+ return ret;
+}
+
+static int dln2_gpio_remove(struct platform_device *pdev)
+{
+ struct dln2_gpio *dln2 = platform_get_drvdata(pdev);
+ int i;
+
+ dln2_unregister_event_cb(pdev, DLN2_GPIO_CONDITION_MET_EV);
+ for (i = 0; i < dln2->gpio.ngpio; i++)
+ flush_work(&dln2->irq_work[i].work);
+ gpiochip_remove(&dln2->gpio);
+
+ return 0;
+}
+
+static struct platform_driver dln2_gpio_driver = {
+ .driver.name = "dln2-gpio",
+ .probe = dln2_gpio_probe,
+ .remove = dln2_gpio_remove,
+};
+
+module_platform_driver(dln2_gpio_driver);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 GPIO interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-gpio");
tc3589x_gpio->chip = template_chip;
tc3589x_gpio->chip.ngpio = tc3589x->num_gpio;
tc3589x_gpio->chip.dev = &pdev->dev;
- tc3589x_gpio->chip.base = (pdata) ? pdata->gpio_base : -1;
+ tc3589x_gpio->chip.base = -1;
#ifdef CONFIG_OF_GPIO
tc3589x_gpio->chip.of_node = np;
ironlake_fdi_disable(crtc);
ironlake_disable_pch_transcoder(dev_priv, pipe);
- intel_set_pch_fifo_underrun_reporting(dev, pipe, true);
if (HAS_PCH_CPT(dev)) {
/* disable TRANS_DP_CTL */
if (intel_crtc->config.has_pch_encoder) {
lpt_disable_pch_transcoder(dev_priv);
- intel_set_pch_fifo_underrun_reporting(dev, TRANSCODER_A, true);
intel_ddi_fdi_disable(crtc);
}
int pipe;
u8 pin;
+ /*
+ * Unlock registers and just leave them unlocked. Do this before
+ * checking quirk lists to avoid bogus WARNINGs.
+ */
+ if (HAS_PCH_SPLIT(dev)) {
+ I915_WRITE(PCH_PP_CONTROL,
+ I915_READ(PCH_PP_CONTROL) | PANEL_UNLOCK_REGS);
+ } else {
+ I915_WRITE(PP_CONTROL,
+ I915_READ(PP_CONTROL) | PANEL_UNLOCK_REGS);
+ }
if (!intel_lvds_supported(dev))
return;
lvds_encoder->a3_power = I915_READ(lvds_encoder->reg) &
LVDS_A3_POWER_MASK;
- /*
- * Unlock registers and just
- * leave them unlocked
- */
- if (HAS_PCH_SPLIT(dev)) {
- I915_WRITE(PCH_PP_CONTROL,
- I915_READ(PCH_PP_CONTROL) | PANEL_UNLOCK_REGS);
- } else {
- I915_WRITE(PP_CONTROL,
- I915_READ(PP_CONTROL) | PANEL_UNLOCK_REGS);
- }
lvds_connector->lid_notifier.notifier_call = intel_lid_notify;
if (acpi_lid_notifier_register(&lvds_connector->lid_notifier)) {
DRM_DEBUG_KMS("lid notifier registration failed\n");
device->oclass[NVDEV_ENGINE_BSP ] = &nvc0_bsp_oclass;
device->oclass[NVDEV_ENGINE_PPP ] = &nvc0_ppp_oclass;
device->oclass[NVDEV_ENGINE_COPY0 ] = &nvc0_copy0_oclass;
- device->oclass[NVDEV_ENGINE_COPY1 ] = &nvc0_copy1_oclass;
device->oclass[NVDEV_ENGINE_DISP ] = nva3_disp_oclass;
device->oclass[NVDEV_ENGINE_PERFMON] = &nvc0_perfmon_oclass;
break;
}
if (status & 0x40000000) {
- nouveau_fifo_uevent(&priv->base);
nv_wr32(priv, 0x002100, 0x40000000);
+ nouveau_fifo_uevent(&priv->base);
status &= ~0x40000000;
}
}
u32 inte = nv_rd32(priv, 0x002628);
u32 unkn;
+ nv_wr32(priv, 0x0025a8 + (engn * 0x04), intr);
+
for (unkn = 0; unkn < 8; unkn++) {
u32 ints = (intr >> (unkn * 0x04)) & inte;
if (ints & 0x1) {
nv_mask(priv, 0x002628, ints, 0);
}
}
-
- nv_wr32(priv, 0x0025a8 + (engn * 0x04), intr);
}
static void
}
if (stat & 0x80000000) {
- nve0_fifo_intr_engine(priv);
nv_wr32(priv, 0x002100, 0x80000000);
+ nve0_fifo_intr_engine(priv);
stat &= ~0x80000000;
}
pci_save_state(pdev);
pci_disable_device(pdev);
- pci_ignore_hotplug(pdev);
pci_set_power_state(pdev, PCI_D3hot);
return 0;
}
ret = nouveau_do_suspend(drm_dev, true);
pci_save_state(pdev);
pci_disable_device(pdev);
+ pci_ignore_hotplug(pdev);
pci_set_power_state(pdev, PCI_D3cold);
drm_dev->switch_power_state = DRM_SWITCH_POWER_DYNAMIC_OFF;
return ret;
return container_of(fence->base.lock, struct nouveau_fence_chan, lock);
}
-static void
+static int
nouveau_fence_signal(struct nouveau_fence *fence)
{
+ int drop = 0;
+
fence_signal_locked(&fence->base);
list_del(&fence->head);
+ rcu_assign_pointer(fence->channel, NULL);
if (test_bit(FENCE_FLAG_USER_BITS, &fence->base.flags)) {
struct nouveau_fence_chan *fctx = nouveau_fctx(fence);
if (!--fctx->notify_ref)
- nvif_notify_put(&fctx->notify);
+ drop = 1;
}
fence_put(&fence->base);
+ return drop;
}
static struct nouveau_fence *
{
struct nouveau_fence *fence;
- nvif_notify_fini(&fctx->notify);
-
spin_lock_irq(&fctx->lock);
while (!list_empty(&fctx->pending)) {
fence = list_entry(fctx->pending.next, typeof(*fence), head);
- nouveau_fence_signal(fence);
- fence->channel = NULL;
+ if (nouveau_fence_signal(fence))
+ nvif_notify_put(&fctx->notify);
}
spin_unlock_irq(&fctx->lock);
+
+ nvif_notify_fini(&fctx->notify);
+ fctx->dead = 1;
+
+ /*
+ * Ensure that all accesses to fence->channel complete before freeing
+ * the channel.
+ */
+ synchronize_rcu();
}
static void
kref_put(&fctx->fence_ref, nouveau_fence_context_put);
}
-static void
+static int
nouveau_fence_update(struct nouveau_channel *chan, struct nouveau_fence_chan *fctx)
{
struct nouveau_fence *fence;
-
+ int drop = 0;
u32 seq = fctx->read(chan);
while (!list_empty(&fctx->pending)) {
fence = list_entry(fctx->pending.next, typeof(*fence), head);
if ((int)(seq - fence->base.seqno) < 0)
- return;
+ break;
- nouveau_fence_signal(fence);
+ drop |= nouveau_fence_signal(fence);
}
+
+ return drop;
}
static int
struct nouveau_fence_chan *fctx =
container_of(notify, typeof(*fctx), notify);
unsigned long flags;
+ int ret = NVIF_NOTIFY_KEEP;
spin_lock_irqsave(&fctx->lock, flags);
if (!list_empty(&fctx->pending)) {
struct nouveau_fence *fence;
+ struct nouveau_channel *chan;
fence = list_entry(fctx->pending.next, typeof(*fence), head);
- nouveau_fence_update(fence->channel, fctx);
+ chan = rcu_dereference_protected(fence->channel, lockdep_is_held(&fctx->lock));
+ if (nouveau_fence_update(fence->channel, fctx))
+ ret = NVIF_NOTIFY_DROP;
}
spin_unlock_irqrestore(&fctx->lock, flags);
- /* Always return keep here. NVIF refcount is handled with nouveau_fence_update */
- return NVIF_NOTIFY_KEEP;
+ return ret;
}
void
if (!ret) {
fence_get(&fence->base);
spin_lock_irq(&fctx->lock);
- nouveau_fence_update(chan, fctx);
+
+ if (nouveau_fence_update(chan, fctx))
+ nvif_notify_put(&fctx->notify);
+
list_add_tail(&fence->head, &fctx->pending);
spin_unlock_irq(&fctx->lock);
}
if (fence->base.ops == &nouveau_fence_ops_legacy ||
fence->base.ops == &nouveau_fence_ops_uevent) {
struct nouveau_fence_chan *fctx = nouveau_fctx(fence);
+ struct nouveau_channel *chan;
unsigned long flags;
if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->base.flags))
return true;
spin_lock_irqsave(&fctx->lock, flags);
- nouveau_fence_update(fence->channel, fctx);
+ chan = rcu_dereference_protected(fence->channel, lockdep_is_held(&fctx->lock));
+ if (chan && nouveau_fence_update(chan, fctx))
+ nvif_notify_put(&fctx->notify);
spin_unlock_irqrestore(&fctx->lock, flags);
}
return fence_is_signaled(&fence->base);
if (fence && (!exclusive || !fobj || !fobj->shared_count)) {
struct nouveau_channel *prev = NULL;
+ bool must_wait = true;
f = nouveau_local_fence(fence, chan->drm);
- if (f)
- prev = f->channel;
+ if (f) {
+ rcu_read_lock();
+ prev = rcu_dereference(f->channel);
+ if (prev && (prev == chan || fctx->sync(f, prev, chan) == 0))
+ must_wait = false;
+ rcu_read_unlock();
+ }
- if (!prev || (prev != chan && (ret = fctx->sync(f, prev, chan))))
+ if (must_wait)
ret = fence_wait(fence, intr);
return ret;
for (i = 0; i < fobj->shared_count && !ret; ++i) {
struct nouveau_channel *prev = NULL;
+ bool must_wait = true;
fence = rcu_dereference_protected(fobj->shared[i],
reservation_object_held(resv));
f = nouveau_local_fence(fence, chan->drm);
- if (f)
- prev = f->channel;
+ if (f) {
+ rcu_read_lock();
+ prev = rcu_dereference(f->channel);
+ if (prev && (prev == chan || fctx->sync(f, prev, chan) == 0))
+ must_wait = false;
+ rcu_read_unlock();
+ }
- if (!prev || (prev != chan && (ret = fctx->sync(f, prev, chan))))
+ if (must_wait)
ret = fence_wait(fence, intr);
-
- if (ret)
- break;
}
return ret;
struct nouveau_fence *fence = from_fence(f);
struct nouveau_fence_chan *fctx = nouveau_fctx(fence);
- return fence->channel ? fctx->name : "dead channel";
+ return !fctx->dead ? fctx->name : "dead channel";
}
/*
{
struct nouveau_fence *fence = from_fence(f);
struct nouveau_fence_chan *fctx = nouveau_fctx(fence);
- struct nouveau_channel *chan = fence->channel;
+ struct nouveau_channel *chan;
+ bool ret = false;
+
+ rcu_read_lock();
+ chan = rcu_dereference(fence->channel);
+ if (chan)
+ ret = (int)(fctx->read(chan) - fence->base.seqno) >= 0;
+ rcu_read_unlock();
- return (int)(fctx->read(chan) - fence->base.seqno) >= 0;
+ return ret;
}
static bool nouveau_fence_no_signaling(struct fence *f)
bool sysmem;
- struct nouveau_channel *channel;
+ struct nouveau_channel __rcu *channel;
unsigned long timeout;
};
char name[32];
struct nvif_notify notify;
- int notify_ref;
+ int notify_ref, dead;
};
struct nouveau_fence_priv {
static int radeon_cs_sync_rings(struct radeon_cs_parser *p)
{
- int i, r = 0;
+ struct radeon_cs_reloc *reloc;
+ int r;
- for (i = 0; i < p->nrelocs; i++) {
+ list_for_each_entry(reloc, &p->validated, tv.head) {
struct reservation_object *resv;
- if (!p->relocs[i].robj)
- continue;
-
- resv = p->relocs[i].robj->tbo.resv;
+ resv = reloc->robj->tbo.resv;
r = radeon_semaphore_sync_resv(p->rdev, p->ib.semaphore, resv,
- p->relocs[i].tv.shared);
-
+ reloc->tv.shared);
if (r)
- break;
+ return r;
}
- return r;
+ return 0;
}
/* XXX: note that this is called from the legacy UMS CS ioctl as well */
/* Get associated drm_crtc: */
drmcrtc = &rdev->mode_info.crtcs[crtc]->base;
+ if (!drmcrtc)
+ return -EINVAL;
/* Helper routine in DRM core does all the work: */
return drm_calc_vbltimestamp_from_scanoutpos(dev, crtc, max_error,
if (!(rdev->flags & RADEON_IS_PCIE))
bo->flags &= ~(RADEON_GEM_GTT_WC | RADEON_GEM_GTT_UC);
+#ifdef CONFIG_X86_32
+ /* XXX: Write-combined CPU mappings of GTT seem broken on 32-bit
+ * See https://bugs.freedesktop.org/show_bug.cgi?id=84627
+ */
+ bo->flags &= ~RADEON_GEM_GTT_WC;
+#endif
+
radeon_ttm_placement_from_domain(bo, domain);
/* Kernel allocation are uninterruptible */
down_read(&rdev->pm.mclk_lock);
ret = -ENOMEM;
goto err_stop_hw;
}
- sd->hid_sensor_hub_client_devs[
- sd->hid_sensor_client_cnt].id =
- PLATFORM_DEVID_AUTO;
sd->hid_sensor_hub_client_devs[
sd->hid_sensor_client_cnt].name = name;
sd->hid_sensor_hub_client_devs[
if (last_hsdev)
last_hsdev->end_collection_index = i;
- ret = mfd_add_devices(&hdev->dev, 0, sd->hid_sensor_hub_client_devs,
- sd->hid_sensor_client_cnt, NULL, 0, NULL);
+ ret = mfd_add_hotplug_devices(&hdev->dev,
+ sd->hid_sensor_hub_client_devs,
+ sd->hid_sensor_client_cnt);
if (ret < 0)
goto err_stop_hw;
This driver can also be built as a module. If so, the module
will be called i2c-diolan-u2c.
+config I2C_DLN2
+ tristate "Diolan DLN-2 USB I2C adapter"
+ depends on MFD_DLN2
+ help
+ If you say yes to this option, support will be included for Diolan
+ DLN2, a USB to I2C interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called i2c-dln2.
+
config I2C_PARPORT
tristate "Parallel port adapter"
depends on PARPORT
# External I2C/SMBus adapter drivers
obj-$(CONFIG_I2C_DIOLAN_U2C) += i2c-diolan-u2c.o
+obj-$(CONFIG_I2C_DLN2) += i2c-dln2.o
obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o
obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o
obj-$(CONFIG_I2C_ROBOTFUZZ_OSIF) += i2c-robotfuzz-osif.o
#define CDNS_I2C_DIVA_MAX 4
#define CDNS_I2C_DIVB_MAX 64
+#define CDNS_I2C_TIMEOUT_MAX 0xFF
+
#define cdns_i2c_readreg(offset) readl_relaxed(id->membase + offset)
#define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
goto err_clk_dis;
}
+ /*
+ * Cadence I2C controller has a bug wherein it generates
+ * invalid read transaction after HW timeout in master receiver mode.
+ * HW timeout is not used by this driver and the interrupt is disabled.
+ * But the feature itself cannot be disabled. Hence maximum value
+ * is written to this register to reduce the chances of error.
+ */
+ cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET);
+
dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n",
id->i2c_clk / 1000, (unsigned long)r_mem->start, id->irq);
if (dev->cmd_err & DAVINCI_I2C_STR_NACK) {
if (msg->flags & I2C_M_IGNORE_NAK)
return msg->len;
- if (stop) {
- w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG);
- w |= DAVINCI_I2C_MDR_STP;
- davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w);
- }
+ w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG);
+ w |= DAVINCI_I2C_MDR_STP;
+ davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w);
return -EREMOTEIO;
}
return -EIO;
}
/* Configure Tx/Rx FIFO threshold levels */
- dw_writel(dev, dev->tx_fifo_depth - 1, DW_IC_TX_TL);
+ dw_writel(dev, dev->tx_fifo_depth / 2, DW_IC_TX_TL);
dw_writel(dev, 0, DW_IC_RX_TL);
/* configure the i2c master */
--- /dev/null
+/*
+ * Driver for the Diolan DLN-2 USB-I2C adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/i2c.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/dln2.h>
+
+#define DLN2_I2C_MODULE_ID 0x03
+#define DLN2_I2C_CMD(cmd) DLN2_CMD(cmd, DLN2_I2C_MODULE_ID)
+
+/* I2C commands */
+#define DLN2_I2C_GET_PORT_COUNT DLN2_I2C_CMD(0x00)
+#define DLN2_I2C_ENABLE DLN2_I2C_CMD(0x01)
+#define DLN2_I2C_DISABLE DLN2_I2C_CMD(0x02)
+#define DLN2_I2C_IS_ENABLED DLN2_I2C_CMD(0x03)
+#define DLN2_I2C_WRITE DLN2_I2C_CMD(0x06)
+#define DLN2_I2C_READ DLN2_I2C_CMD(0x07)
+#define DLN2_I2C_SCAN_DEVICES DLN2_I2C_CMD(0x08)
+#define DLN2_I2C_PULLUP_ENABLE DLN2_I2C_CMD(0x09)
+#define DLN2_I2C_PULLUP_DISABLE DLN2_I2C_CMD(0x0A)
+#define DLN2_I2C_PULLUP_IS_ENABLED DLN2_I2C_CMD(0x0B)
+#define DLN2_I2C_TRANSFER DLN2_I2C_CMD(0x0C)
+#define DLN2_I2C_SET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0D)
+#define DLN2_I2C_GET_MAX_REPLY_COUNT DLN2_I2C_CMD(0x0E)
+
+#define DLN2_I2C_MAX_XFER_SIZE 256
+#define DLN2_I2C_BUF_SIZE (DLN2_I2C_MAX_XFER_SIZE + 16)
+
+struct dln2_i2c {
+ struct platform_device *pdev;
+ struct i2c_adapter adapter;
+ u8 port;
+ /*
+ * Buffer to hold the packet for read or write transfers. One is enough
+ * since we can't have multiple transfers in parallel on the i2c bus.
+ */
+ void *buf;
+};
+
+static int dln2_i2c_enable(struct dln2_i2c *dln2, bool enable)
+{
+ u16 cmd;
+ struct {
+ u8 port;
+ } tx;
+
+ tx.port = dln2->port;
+
+ if (enable)
+ cmd = DLN2_I2C_ENABLE;
+ else
+ cmd = DLN2_I2C_DISABLE;
+
+ return dln2_transfer_tx(dln2->pdev, cmd, &tx, sizeof(tx));
+}
+
+static int dln2_i2c_write(struct dln2_i2c *dln2, u8 addr,
+ u8 *data, u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *tx = dln2->buf;
+ unsigned len;
+
+ BUILD_BUG_ON(sizeof(*tx) > DLN2_I2C_BUF_SIZE);
+
+ tx->port = dln2->port;
+ tx->addr = addr;
+ tx->mem_addr_len = 0;
+ tx->mem_addr = 0;
+ tx->buf_len = cpu_to_le16(data_len);
+ memcpy(tx->buf, data, data_len);
+
+ len = sizeof(*tx) + data_len - DLN2_I2C_MAX_XFER_SIZE;
+ ret = dln2_transfer_tx(dln2->pdev, DLN2_I2C_WRITE, tx, len);
+ if (ret < 0)
+ return ret;
+
+ return data_len;
+}
+
+static int dln2_i2c_read(struct dln2_i2c *dln2, u16 addr, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct {
+ u8 port;
+ u8 addr;
+ u8 mem_addr_len;
+ __le32 mem_addr;
+ __le16 buf_len;
+ } __packed tx;
+ struct {
+ __le16 buf_len;
+ u8 buf[DLN2_I2C_MAX_XFER_SIZE];
+ } __packed *rx = dln2->buf;
+ unsigned rx_len = sizeof(*rx);
+
+ BUILD_BUG_ON(sizeof(*rx) > DLN2_I2C_BUF_SIZE);
+
+ tx.port = dln2->port;
+ tx.addr = addr;
+ tx.mem_addr_len = 0;
+ tx.mem_addr = 0;
+ tx.buf_len = cpu_to_le16(data_len);
+
+ ret = dln2_transfer(dln2->pdev, DLN2_I2C_READ, &tx, sizeof(tx),
+ rx, &rx_len);
+ if (ret < 0)
+ return ret;
+ if (rx_len < sizeof(rx->buf_len) + data_len)
+ return -EPROTO;
+ if (le16_to_cpu(rx->buf_len) != data_len)
+ return -EPROTO;
+
+ memcpy(data, rx->buf, data_len);
+
+ return data_len;
+}
+
+static int dln2_i2c_xfer(struct i2c_adapter *adapter,
+ struct i2c_msg *msgs, int num)
+{
+ struct dln2_i2c *dln2 = i2c_get_adapdata(adapter);
+ struct i2c_msg *pmsg;
+ struct device *dev = &dln2->adapter.dev;
+ int i;
+
+ for (i = 0; i < num; i++) {
+ int ret;
+
+ pmsg = &msgs[i];
+
+ if (pmsg->len > DLN2_I2C_MAX_XFER_SIZE) {
+ dev_warn(dev, "maximum transfer size exceeded\n");
+ return -EOPNOTSUPP;
+ }
+
+ if (pmsg->flags & I2C_M_RD) {
+ ret = dln2_i2c_read(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret < 0)
+ return ret;
+
+ pmsg->len = ret;
+ } else {
+ ret = dln2_i2c_write(dln2, pmsg->addr, pmsg->buf,
+ pmsg->len);
+ if (ret != pmsg->len)
+ return -EPROTO;
+ }
+ }
+
+ return num;
+}
+
+static u32 dln2_i2c_func(struct i2c_adapter *a)
+{
+ return I2C_FUNC_I2C | I2C_FUNC_SMBUS_BYTE | I2C_FUNC_SMBUS_BYTE_DATA |
+ I2C_FUNC_SMBUS_WORD_DATA | I2C_FUNC_SMBUS_BLOCK_PROC_CALL |
+ I2C_FUNC_SMBUS_I2C_BLOCK;
+}
+
+static const struct i2c_algorithm dln2_i2c_usb_algorithm = {
+ .master_xfer = dln2_i2c_xfer,
+ .functionality = dln2_i2c_func,
+};
+
+static int dln2_i2c_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct dln2_i2c *dln2;
+ struct device *dev = &pdev->dev;
+ struct dln2_platform_data *pdata = dev_get_platdata(&pdev->dev);
+
+ dln2 = devm_kzalloc(dev, sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->buf = devm_kmalloc(dev, DLN2_I2C_BUF_SIZE, GFP_KERNEL);
+ if (!dln2->buf)
+ return -ENOMEM;
+
+ dln2->pdev = pdev;
+ dln2->port = pdata->port;
+
+ /* setup i2c adapter description */
+ dln2->adapter.owner = THIS_MODULE;
+ dln2->adapter.class = I2C_CLASS_HWMON;
+ dln2->adapter.algo = &dln2_i2c_usb_algorithm;
+ dln2->adapter.dev.parent = dev;
+ i2c_set_adapdata(&dln2->adapter, dln2);
+ snprintf(dln2->adapter.name, sizeof(dln2->adapter.name), "%s-%s-%d",
+ "dln2-i2c", dev_name(pdev->dev.parent), dln2->port);
+
+ platform_set_drvdata(pdev, dln2);
+
+ /* initialize the i2c interface */
+ ret = dln2_i2c_enable(dln2, true);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize adapter: %d\n", ret);
+ return ret;
+ }
+
+ /* and finally attach to i2c layer */
+ ret = i2c_add_adapter(&dln2->adapter);
+ if (ret < 0) {
+ dev_err(dev, "failed to add I2C adapter: %d\n", ret);
+ goto out_disable;
+ }
+
+ return 0;
+
+out_disable:
+ dln2_i2c_enable(dln2, false);
+
+ return ret;
+}
+
+static int dln2_i2c_remove(struct platform_device *pdev)
+{
+ struct dln2_i2c *dln2 = platform_get_drvdata(pdev);
+
+ i2c_del_adapter(&dln2->adapter);
+ dln2_i2c_enable(dln2, false);
+
+ return 0;
+}
+
+static struct platform_driver dln2_i2c_driver = {
+ .driver.name = "dln2-i2c",
+ .probe = dln2_i2c_probe,
+ .remove = dln2_i2c_remove,
+};
+
+module_platform_driver(dln2_i2c_driver);
+
+MODULE_AUTHOR("Laurentiu Palcu <laurentiu.palcu@intel.com>");
+MODULE_DESCRIPTION("Driver for the Diolan DLN2 I2C master interface");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:dln2-i2c");
if (stat & OMAP_I2C_STAT_NACK) {
err |= OMAP_I2C_STAT_NACK;
omap_i2c_ack_stat(dev, OMAP_I2C_STAT_NACK);
- break;
}
if (stat & OMAP_I2C_STAT_AL) {
dev_err(dev->dev, "Arbitration lost\n");
err |= OMAP_I2C_STAT_AL;
omap_i2c_ack_stat(dev, OMAP_I2C_STAT_AL);
- break;
}
/*
if (dev->fifo_size)
num_bytes = dev->buf_len;
- omap_i2c_receive_data(dev, num_bytes, true);
-
- if (dev->errata & I2C_OMAP_ERRATA_I207)
+ if (dev->errata & I2C_OMAP_ERRATA_I207) {
i2c_omap_errata_i207(dev, stat);
+ num_bytes = (omap_i2c_read_reg(dev,
+ OMAP_I2C_BUFSTAT_REG) >> 8) & 0x3F;
+ }
+ omap_i2c_receive_data(dev, num_bytes, true);
omap_i2c_ack_stat(dev, OMAP_I2C_STAT_RDR);
continue;
}
help
Say yes here to build support for Atmel AT91 ADC.
+config AXP288_ADC
+ tristate "X-Powers AXP288 ADC driver"
+ depends on MFD_AXP20X
+ help
+ Say yes here to have support for X-Powers power management IC (PMIC) ADC
+ device. Depending on platform configuration, this general purpose ADC can
+ be used for sampling sensors such as thermal resistors.
+
config EXYNOS_ADC
tristate "Exynos ADC driver support"
depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
obj-$(CONFIG_AD7887) += ad7887.o
obj-$(CONFIG_AD799X) += ad799x.o
obj-$(CONFIG_AT91_ADC) += at91_adc.o
+obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
obj-$(CONFIG_LP8788_ADC) += lp8788_adc.o
obj-$(CONFIG_MAX1027) += max1027.o
--- /dev/null
+/*
+ * axp288_adc.c - X-Powers AXP288 PMIC ADC Driver
+ *
+ * Copyright (C) 2014 Intel Corporation
+ *
+ * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/platform_device.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/machine.h>
+#include <linux/iio/driver.h>
+
+#define AXP288_ADC_EN_MASK 0xF1
+#define AXP288_ADC_TS_PIN_GPADC 0xF2
+#define AXP288_ADC_TS_PIN_ON 0xF3
+
+enum axp288_adc_id {
+ AXP288_ADC_TS,
+ AXP288_ADC_PMIC,
+ AXP288_ADC_GP,
+ AXP288_ADC_BATT_CHRG_I,
+ AXP288_ADC_BATT_DISCHRG_I,
+ AXP288_ADC_BATT_V,
+ AXP288_ADC_NR_CHAN,
+};
+
+struct axp288_adc_info {
+ int irq;
+ struct regmap *regmap;
+};
+
+static const struct iio_chan_spec const axp288_adc_channels[] = {
+ {
+ .indexed = 1,
+ .type = IIO_TEMP,
+ .channel = 0,
+ .address = AXP288_TS_ADC_H,
+ .datasheet_name = "TS_PIN",
+ }, {
+ .indexed = 1,
+ .type = IIO_TEMP,
+ .channel = 1,
+ .address = AXP288_PMIC_ADC_H,
+ .datasheet_name = "PMIC_TEMP",
+ }, {
+ .indexed = 1,
+ .type = IIO_TEMP,
+ .channel = 2,
+ .address = AXP288_GP_ADC_H,
+ .datasheet_name = "GPADC",
+ }, {
+ .indexed = 1,
+ .type = IIO_CURRENT,
+ .channel = 3,
+ .address = AXP20X_BATT_CHRG_I_H,
+ .datasheet_name = "BATT_CHG_I",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ }, {
+ .indexed = 1,
+ .type = IIO_CURRENT,
+ .channel = 4,
+ .address = AXP20X_BATT_DISCHRG_I_H,
+ .datasheet_name = "BATT_DISCHRG_I",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ }, {
+ .indexed = 1,
+ .type = IIO_VOLTAGE,
+ .channel = 5,
+ .address = AXP20X_BATT_V_H,
+ .datasheet_name = "BATT_V",
+ .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED),
+ },
+};
+
+#define AXP288_ADC_MAP(_adc_channel_label, _consumer_dev_name, \
+ _consumer_channel) \
+ { \
+ .adc_channel_label = _adc_channel_label, \
+ .consumer_dev_name = _consumer_dev_name, \
+ .consumer_channel = _consumer_channel, \
+ }
+
+/* for consumer drivers */
+static struct iio_map axp288_adc_default_maps[] = {
+ AXP288_ADC_MAP("TS_PIN", "axp288-batt", "axp288-batt-temp"),
+ AXP288_ADC_MAP("PMIC_TEMP", "axp288-pmic", "axp288-pmic-temp"),
+ AXP288_ADC_MAP("GPADC", "axp288-gpadc", "axp288-system-temp"),
+ AXP288_ADC_MAP("BATT_CHG_I", "axp288-chrg", "axp288-chrg-curr"),
+ AXP288_ADC_MAP("BATT_DISCHRG_I", "axp288-chrg", "axp288-chrg-d-curr"),
+ AXP288_ADC_MAP("BATT_V", "axp288-batt", "axp288-batt-volt"),
+ {},
+};
+
+static int axp288_adc_read_channel(int *val, unsigned long address,
+ struct regmap *regmap)
+{
+ u8 buf[2];
+
+ if (regmap_bulk_read(regmap, address, buf, 2))
+ return -EIO;
+ *val = (buf[0] << 4) + ((buf[1] >> 4) & 0x0F);
+
+ return IIO_VAL_INT;
+}
+
+static int axp288_adc_set_ts(struct regmap *regmap, unsigned int mode,
+ unsigned long address)
+{
+ /* channels other than GPADC do not need to switch TS pin */
+ if (address != AXP288_GP_ADC_H)
+ return 0;
+
+ return regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, mode);
+}
+
+static int axp288_adc_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ int ret;
+ struct axp288_adc_info *info = iio_priv(indio_dev);
+
+ mutex_lock(&indio_dev->mlock);
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_GPADC,
+ chan->address)) {
+ dev_err(&indio_dev->dev, "GPADC mode\n");
+ ret = -EINVAL;
+ break;
+ }
+ ret = axp288_adc_read_channel(val, chan->address, info->regmap);
+ if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_ON,
+ chan->address))
+ dev_err(&indio_dev->dev, "TS pin restore\n");
+ break;
+ case IIO_CHAN_INFO_PROCESSED:
+ ret = axp288_adc_read_channel(val, chan->address, info->regmap);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+ mutex_unlock(&indio_dev->mlock);
+
+ return ret;
+}
+
+static int axp288_adc_set_state(struct regmap *regmap)
+{
+ /* ADC should be always enabled for internal FG to function */
+ if (regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, AXP288_ADC_TS_PIN_ON))
+ return -EIO;
+
+ return regmap_write(regmap, AXP20X_ADC_EN1, AXP288_ADC_EN_MASK);
+}
+
+static const struct iio_info axp288_adc_iio_info = {
+ .read_raw = &axp288_adc_read_raw,
+ .driver_module = THIS_MODULE,
+};
+
+static int axp288_adc_probe(struct platform_device *pdev)
+{
+ int ret;
+ struct axp288_adc_info *info;
+ struct iio_dev *indio_dev;
+ struct axp20x_dev *axp20x = dev_get_drvdata(pdev->dev.parent);
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*info));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ info = iio_priv(indio_dev);
+ info->irq = platform_get_irq(pdev, 0);
+ if (info->irq < 0) {
+ dev_err(&pdev->dev, "no irq resource?\n");
+ return info->irq;
+ }
+ platform_set_drvdata(pdev, indio_dev);
+ info->regmap = axp20x->regmap;
+ /*
+ * Set ADC to enabled state at all time, including system suspend.
+ * otherwise internal fuel gauge functionality may be affected.
+ */
+ ret = axp288_adc_set_state(axp20x->regmap);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to enable ADC device\n");
+ return ret;
+ }
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->name = pdev->name;
+ indio_dev->channels = axp288_adc_channels;
+ indio_dev->num_channels = ARRAY_SIZE(axp288_adc_channels);
+ indio_dev->info = &axp288_adc_iio_info;
+ indio_dev->modes = INDIO_DIRECT_MODE;
+ ret = iio_map_array_register(indio_dev, axp288_adc_default_maps);
+ if (ret < 0)
+ return ret;
+
+ ret = iio_device_register(indio_dev);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "unable to register iio device\n");
+ goto err_array_unregister;
+ }
+ return 0;
+
+err_array_unregister:
+ iio_map_array_unregister(indio_dev);
+
+ return ret;
+}
+
+static int axp288_adc_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+
+ iio_device_unregister(indio_dev);
+ iio_map_array_unregister(indio_dev);
+
+ return 0;
+}
+
+static struct platform_device_id axp288_adc_id_table[] = {
+ { .name = "axp288_adc" },
+ {},
+};
+
+static struct platform_driver axp288_adc_driver = {
+ .probe = axp288_adc_probe,
+ .remove = axp288_adc_remove,
+ .id_table = axp288_adc_id_table,
+ .driver = {
+ .name = "axp288_adc",
+ },
+};
+
+MODULE_DEVICE_TABLE(platform, axp288_adc_id_table);
+
+module_platform_driver(axp288_adc_driver);
+
+MODULE_AUTHOR("Jacob Pan <jacob.jun.pan@linux.intel.com>");
+MODULE_DESCRIPTION("X-Powers AXP288 ADC Driver");
+MODULE_LICENSE("GPL");
err_free_client:
evdev_detach_client(evdev, client);
- kfree(client);
+ kvfree(client);
return error;
}
ret = smiapp_set_compose(subdev, fh, sel);
break;
default:
- BUG();
+ ret = -EINVAL;
}
mutex_unlock(&sensor->mutex);
for (line = 0; line < lines; line++) {
while (offset && offset >= sg_dma_len(sg)) {
offset -= sg_dma_len(sg);
- sg++;
+ sg = sg_next(sg);
}
if (lpi && line > 0 && !(line % lpi))
*(rp++) = cpu_to_le32(0); /* bits 63-32 */
todo -= (sg_dma_len(sg)-offset);
offset = 0;
- sg++;
+ sg = sg_next(sg);
while (todo > sg_dma_len(sg)) {
*(rp++) = cpu_to_le32(RISC_WRITE|
sg_dma_len(sg));
*(rp++) = cpu_to_le32(sg_dma_address(sg));
*(rp++) = cpu_to_le32(0); /* bits 63-32 */
todo -= sg_dma_len(sg);
- sg++;
+ sg = sg_next(sg);
}
*(rp++) = cpu_to_le32(RISC_WRITE|RISC_EOL|todo);
*(rp++) = cpu_to_le32(sg_dma_address(sg));
if (!status)
return IRQ_NONE;
- if (status & ~solo_dev->irq_mask) {
- solo_reg_write(solo_dev, SOLO_IRQ_STAT,
- status & ~solo_dev->irq_mask);
- status &= solo_dev->irq_mask;
- }
+ /* Acknowledge all interrupts immediately */
+ solo_reg_write(solo_dev, SOLO_IRQ_STAT, status);
if (status & SOLO_IRQ_PCI_ERR)
solo_p2m_error_isr(solo_dev);
if (status & SOLO_IRQ_G723)
solo_g723_isr(solo_dev);
- /* Clear all interrupts handled */
- solo_reg_write(solo_dev, SOLO_IRQ_STAT, status);
-
return IRQ_HANDLED;
}
case 32:
if ((scancode & RC6_6A_LCC_MASK) == RC6_6A_MCE_CC) {
protocol = RC_TYPE_RC6_MCE;
- scancode &= ~RC6_6A_MCE_TOGGLE_MASK;
toggle = !!(scancode & RC6_6A_MCE_TOGGLE_MASK);
+ scancode &= ~RC6_6A_MCE_TOGGLE_MASK;
} else {
protocol = RC_BIT_RC6_6A_32;
toggle = 0;
break;
case V4L2_PIX_FMT_JPEG:
case V4L2_PIX_FMT_MJPEG:
- buf->vb.v4l2_buf.length = jpgsize;
+ vb2_set_plane_payload(&buf->vb, 0, jpgsize);
memcpy(vbuf, tmpbuf, jpgsize);
break;
case V4L2_PIX_FMT_YUV422P:
additional drivers must be enabled in order to use the
functionality of the device.
+config MFD_ATMEL_HLCDC
+ tristate "Atmel HLCDC (High-end LCD Controller)"
+ select MFD_CORE
+ select REGMAP_MMIO
+ depends on OF
+ help
+ If you say yes here you get support for the HLCDC block.
+ This driver provides common support for accessing the device,
+ additional drivers must be enabled in order to use the
+ functionality of the device.
+
config MFD_BCM590XX
tristate "Broadcom BCM590xx PMUs"
select MFD_CORE
select REGMAP_IRQ
depends on I2C=y
help
- If you say Y here you get support for the X-Powers AXP202 and AXP209.
+ If you say Y here you get support for the X-Powers AXP202, AXP209 and
+ AXP288 power management IC (PMIC).
This driver include only the core APIs. You have to select individual
components like regulators or the PEK (Power Enable Key) under the
corresponding menus.
Additional drivers must be enabled in order to use the functionality
of the device.
+config MFD_DLN2
+ tristate "Diolan DLN2 support"
+ select MFD_CORE
+ depends on USB
+ help
+ This adds support for Diolan USB-I2C/SPI/GPIO Master Adapter
+ DLN-2. Additional drivers such as I2C_DLN2, GPIO_DLN2,
+ etc. must be enabled in order to use the functionality of
+ the device.
+
config MFD_MC13XXX
tristate
depends on (SPI_MASTER || I2C)
select MFD_CORE
select REGMAP_I2C
select REGMAP_IRQ
- select REGULATOR
help
Support for the Samsung Electronics MFD series.
This driver provides common support for accessing the device,
obj-$(CONFIG_MFD_CROS_EC_I2C) += cros_ec_i2c.o
obj-$(CONFIG_MFD_CROS_EC_SPI) += cros_ec_spi.o
-rtsx_pci-objs := rtsx_pcr.o rts5209.o rts5229.o rtl8411.o rts5227.o rts5249.o
+rtsx_pci-objs := rtsx_pcr.o rtsx_gops.o rts5209.o rts5229.o rtl8411.o rts5227.o rts5249.o
obj-$(CONFIG_MFD_RTSX_PCI) += rtsx_pci.o
obj-$(CONFIG_MFD_RTSX_USB) += rtsx_usb.o
obj-$(CONFIG_TPS65911_COMPARATOR) += tps65911-comparator.o
obj-$(CONFIG_MFD_TPS65090) += tps65090.o
obj-$(CONFIG_MFD_AAT2870_CORE) += aat2870-core.o
+obj-$(CONFIG_MFD_ATMEL_HLCDC) += atmel-hlcdc.o
obj-$(CONFIG_MFD_INTEL_MSIC) += intel_msic.o
obj-$(CONFIG_MFD_PALMAS) += palmas.o
obj-$(CONFIG_MFD_VIPERBOARD) += viperboard.o
obj-$(CONFIG_MFD_IPAQ_MICRO) += ipaq-micro.o
obj-$(CONFIG_MFD_MENF21BMC) += menf21bmc.o
obj-$(CONFIG_MFD_HI6421_PMIC) += hi6421-pmic-core.o
+obj-$(CONFIG_MFD_DLN2) += dln2.o
intel-soc-pmic-objs := intel_soc_pmic_core.o intel_soc_pmic_crc.o
obj-$(CONFIG_INTEL_SOC_PMIC) += intel-soc-pmic.o
}
}
-/*
- * Use the AB WD to reset the platform. It will perform a hard
- * reset instead of a soft reset. Write the reset reason to
- * the AB before reset, which can be read upon restart.
- */
-void ab8500_restart(char mode, const char *cmd)
-{
- struct ab8500_platform_data *plat;
- struct ab8500_sysctrl_platform_data *pdata;
- u16 reason = 0;
- u8 val;
-
- if (sysctrl_dev == NULL) {
- pr_err("%s: sysctrl not initialized\n", __func__);
- return;
- }
-
- plat = dev_get_platdata(sysctrl_dev->parent);
- pdata = plat->sysctrl;
- if (pdata && pdata->reboot_reason_code)
- reason = pdata->reboot_reason_code(cmd);
- else
- pr_warn("[%s] No reboot reason set. Default reason %d\n",
- __func__, reason);
-
- /*
- * Disable RTC alarm, just a precaution so that no alarm
- * is running when WD reset is executed.
- */
- abx500_get_register_interruptible(sysctrl_dev, AB8500_RTC,
- RTC_CTRL , &val);
- abx500_set_register_interruptible(sysctrl_dev, AB8500_RTC,
- RTC_CTRL , (val & ~RTC_ALARM_ENABLE));
-
- /*
- * Android is not using the RTC alarm registers during reboot
- * so we borrow them for writing the reason of reset
- */
-
- /* reason[8 LSB] */
- val = reason & 0xFF;
- abx500_set_register_interruptible(sysctrl_dev, AB8500_RTC,
- AB8500_ALARM_MIN_LOW , val);
-
- /* reason[8 MSB] */
- val = (reason>>8) & 0xFF;
- abx500_set_register_interruptible(sysctrl_dev, AB8500_RTC,
- AB8500_ALARM_MIN_MID , val);
-
- /* Setting WD timeout to 0 */
- ab8500_sysctrl_write(AB8500_MAINWDOGTIMER, 0xFF, 0x0);
-
- /* Setting the parameters to AB8500 WD*/
- ab8500_sysctrl_write(AB8500_MAINWDOGCTRL, 0xFF, (AB8500_ENABLE_WD |
- AB8500_WD_RESTART_ON_EXPIRE | AB8500_KICK_WD));
-}
-
static inline bool valid_bank(u8 bank)
{
return ((bank == AB8500_SYS_CTRL1_BLOCK) ||
static int arizona_spi_remove(struct spi_device *spi)
{
struct arizona *arizona = spi_get_drvdata(spi);
+
arizona_dev_exit(arizona);
+
return 0;
}
--- /dev/null
+/*
+ * Copyright (C) 2014 Free Electrons
+ * Copyright (C) 2014 Atmel
+ *
+ * Author: Boris BREZILLON <boris.brezillon@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/atmel-hlcdc.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define ATMEL_HLCDC_REG_MAX (0x4000 - 0x4)
+
+static const struct mfd_cell atmel_hlcdc_cells[] = {
+ {
+ .name = "atmel-hlcdc-pwm",
+ .of_compatible = "atmel,hlcdc-pwm",
+ },
+ {
+ .name = "atmel-hlcdc-dc",
+ .of_compatible = "atmel,hlcdc-display-controller",
+ },
+};
+
+static const struct regmap_config atmel_hlcdc_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = ATMEL_HLCDC_REG_MAX,
+};
+
+static int atmel_hlcdc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct atmel_hlcdc *hlcdc;
+ struct resource *res;
+ void __iomem *regs;
+
+ hlcdc = devm_kzalloc(dev, sizeof(*hlcdc), GFP_KERNEL);
+ if (!hlcdc)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(regs))
+ return PTR_ERR(regs);
+
+ hlcdc->irq = platform_get_irq(pdev, 0);
+ if (hlcdc->irq < 0)
+ return hlcdc->irq;
+
+ hlcdc->periph_clk = devm_clk_get(dev, "periph_clk");
+ if (IS_ERR(hlcdc->periph_clk)) {
+ dev_err(dev, "failed to get peripheral clock\n");
+ return PTR_ERR(hlcdc->periph_clk);
+ }
+
+ hlcdc->sys_clk = devm_clk_get(dev, "sys_clk");
+ if (IS_ERR(hlcdc->sys_clk)) {
+ dev_err(dev, "failed to get system clock\n");
+ return PTR_ERR(hlcdc->sys_clk);
+ }
+
+ hlcdc->slow_clk = devm_clk_get(dev, "slow_clk");
+ if (IS_ERR(hlcdc->slow_clk)) {
+ dev_err(dev, "failed to get slow clock\n");
+ return PTR_ERR(hlcdc->slow_clk);
+ }
+
+ hlcdc->regmap = devm_regmap_init_mmio(dev, regs,
+ &atmel_hlcdc_regmap_config);
+ if (IS_ERR(hlcdc->regmap))
+ return PTR_ERR(hlcdc->regmap);
+
+ dev_set_drvdata(dev, hlcdc);
+
+ return mfd_add_devices(dev, -1, atmel_hlcdc_cells,
+ ARRAY_SIZE(atmel_hlcdc_cells),
+ NULL, 0, NULL);
+}
+
+static int atmel_hlcdc_remove(struct platform_device *pdev)
+{
+ mfd_remove_devices(&pdev->dev);
+
+ return 0;
+}
+
+static const struct of_device_id atmel_hlcdc_match[] = {
+ { .compatible = "atmel,sama5d3-hlcdc" },
+ { /* sentinel */ },
+};
+
+static struct platform_driver atmel_hlcdc_driver = {
+ .probe = atmel_hlcdc_probe,
+ .remove = atmel_hlcdc_remove,
+ .driver = {
+ .name = "atmel-hlcdc",
+ .of_match_table = atmel_hlcdc_match,
+ },
+};
+module_platform_driver(atmel_hlcdc_driver);
+
+MODULE_ALIAS("platform:atmel-hlcdc");
+MODULE_AUTHOR("Boris Brezillon <boris.brezillon@free-electrons.com>");
+MODULE_DESCRIPTION("Atmel HLCDC driver");
+MODULE_LICENSE("GPL v2");
/*
- * axp20x.c - MFD core driver for the X-Powers AXP202 and AXP209
+ * axp20x.c - MFD core driver for the X-Powers' Power Management ICs
*
- * AXP20x comprises an adaptive USB-Compatible PWM charger, 2 BUCK DC-DC
- * converters, 5 LDOs, multiple 12-bit ADCs of voltage, current and temperature
- * as well as 4 configurable GPIOs.
+ * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC
+ * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature
+ * as well as configurable GPIOs.
*
* Author: Carlo Caione <carlo@caione.org>
*
#include <linux/mfd/core.h>
#include <linux/of_device.h>
#include <linux/of_irq.h>
+#include <linux/acpi.h>
#define AXP20X_OFF 0x80
+static const char const *axp20x_model_names[] = {
+ "AXP202",
+ "AXP209",
+ "AXP288",
+};
+
static const struct regmap_range axp20x_writeable_ranges[] = {
regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ5_STATE),
regmap_reg_range(AXP20X_DCDC_MODE, AXP20X_FG_RES),
.n_yes_ranges = ARRAY_SIZE(axp20x_volatile_ranges),
};
+static const struct regmap_range axp288_writeable_ranges[] = {
+ regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_IRQ6_STATE),
+ regmap_reg_range(AXP20X_DCDC_MODE, AXP288_FG_TUNE5),
+};
+
+static const struct regmap_range axp288_volatile_ranges[] = {
+ regmap_reg_range(AXP20X_IRQ1_EN, AXP20X_IPSOUT_V_HIGH_L),
+};
+
+static const struct regmap_access_table axp288_writeable_table = {
+ .yes_ranges = axp288_writeable_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp288_writeable_ranges),
+};
+
+static const struct regmap_access_table axp288_volatile_table = {
+ .yes_ranges = axp288_volatile_ranges,
+ .n_yes_ranges = ARRAY_SIZE(axp288_volatile_ranges),
+};
+
static struct resource axp20x_pek_resources[] = {
{
.name = "PEK_DBR",
},
};
+static struct resource axp288_battery_resources[] = {
+ {
+ .start = AXP288_IRQ_QWBTU,
+ .end = AXP288_IRQ_QWBTU,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_WBTU,
+ .end = AXP288_IRQ_WBTU,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_QWBTO,
+ .end = AXP288_IRQ_QWBTO,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_WBTO,
+ .end = AXP288_IRQ_WBTO,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_WL2,
+ .end = AXP288_IRQ_WL2,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_WL1,
+ .end = AXP288_IRQ_WL1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
static const struct regmap_config axp20x_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
.cache_type = REGCACHE_RBTREE,
};
-#define AXP20X_IRQ(_irq, _off, _mask) \
- [AXP20X_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
+static const struct regmap_config axp288_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .wr_table = &axp288_writeable_table,
+ .volatile_table = &axp288_volatile_table,
+ .max_register = AXP288_FG_TUNE5,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+#define INIT_REGMAP_IRQ(_variant, _irq, _off, _mask) \
+ [_variant##_IRQ_##_irq] = { .reg_offset = (_off), .mask = BIT(_mask) }
static const struct regmap_irq axp20x_regmap_irqs[] = {
- AXP20X_IRQ(ACIN_OVER_V, 0, 7),
- AXP20X_IRQ(ACIN_PLUGIN, 0, 6),
- AXP20X_IRQ(ACIN_REMOVAL, 0, 5),
- AXP20X_IRQ(VBUS_OVER_V, 0, 4),
- AXP20X_IRQ(VBUS_PLUGIN, 0, 3),
- AXP20X_IRQ(VBUS_REMOVAL, 0, 2),
- AXP20X_IRQ(VBUS_V_LOW, 0, 1),
- AXP20X_IRQ(BATT_PLUGIN, 1, 7),
- AXP20X_IRQ(BATT_REMOVAL, 1, 6),
- AXP20X_IRQ(BATT_ENT_ACT_MODE, 1, 5),
- AXP20X_IRQ(BATT_EXIT_ACT_MODE, 1, 4),
- AXP20X_IRQ(CHARG, 1, 3),
- AXP20X_IRQ(CHARG_DONE, 1, 2),
- AXP20X_IRQ(BATT_TEMP_HIGH, 1, 1),
- AXP20X_IRQ(BATT_TEMP_LOW, 1, 0),
- AXP20X_IRQ(DIE_TEMP_HIGH, 2, 7),
- AXP20X_IRQ(CHARG_I_LOW, 2, 6),
- AXP20X_IRQ(DCDC1_V_LONG, 2, 5),
- AXP20X_IRQ(DCDC2_V_LONG, 2, 4),
- AXP20X_IRQ(DCDC3_V_LONG, 2, 3),
- AXP20X_IRQ(PEK_SHORT, 2, 1),
- AXP20X_IRQ(PEK_LONG, 2, 0),
- AXP20X_IRQ(N_OE_PWR_ON, 3, 7),
- AXP20X_IRQ(N_OE_PWR_OFF, 3, 6),
- AXP20X_IRQ(VBUS_VALID, 3, 5),
- AXP20X_IRQ(VBUS_NOT_VALID, 3, 4),
- AXP20X_IRQ(VBUS_SESS_VALID, 3, 3),
- AXP20X_IRQ(VBUS_SESS_END, 3, 2),
- AXP20X_IRQ(LOW_PWR_LVL1, 3, 1),
- AXP20X_IRQ(LOW_PWR_LVL2, 3, 0),
- AXP20X_IRQ(TIMER, 4, 7),
- AXP20X_IRQ(PEK_RIS_EDGE, 4, 6),
- AXP20X_IRQ(PEK_FAL_EDGE, 4, 5),
- AXP20X_IRQ(GPIO3_INPUT, 4, 3),
- AXP20X_IRQ(GPIO2_INPUT, 4, 2),
- AXP20X_IRQ(GPIO1_INPUT, 4, 1),
- AXP20X_IRQ(GPIO0_INPUT, 4, 0),
+ INIT_REGMAP_IRQ(AXP20X, ACIN_OVER_V, 0, 7),
+ INIT_REGMAP_IRQ(AXP20X, ACIN_PLUGIN, 0, 6),
+ INIT_REGMAP_IRQ(AXP20X, ACIN_REMOVAL, 0, 5),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_OVER_V, 0, 4),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_PLUGIN, 0, 3),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_REMOVAL, 0, 2),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_V_LOW, 0, 1),
+ INIT_REGMAP_IRQ(AXP20X, BATT_PLUGIN, 1, 7),
+ INIT_REGMAP_IRQ(AXP20X, BATT_REMOVAL, 1, 6),
+ INIT_REGMAP_IRQ(AXP20X, BATT_ENT_ACT_MODE, 1, 5),
+ INIT_REGMAP_IRQ(AXP20X, BATT_EXIT_ACT_MODE, 1, 4),
+ INIT_REGMAP_IRQ(AXP20X, CHARG, 1, 3),
+ INIT_REGMAP_IRQ(AXP20X, CHARG_DONE, 1, 2),
+ INIT_REGMAP_IRQ(AXP20X, BATT_TEMP_HIGH, 1, 1),
+ INIT_REGMAP_IRQ(AXP20X, BATT_TEMP_LOW, 1, 0),
+ INIT_REGMAP_IRQ(AXP20X, DIE_TEMP_HIGH, 2, 7),
+ INIT_REGMAP_IRQ(AXP20X, CHARG_I_LOW, 2, 6),
+ INIT_REGMAP_IRQ(AXP20X, DCDC1_V_LONG, 2, 5),
+ INIT_REGMAP_IRQ(AXP20X, DCDC2_V_LONG, 2, 4),
+ INIT_REGMAP_IRQ(AXP20X, DCDC3_V_LONG, 2, 3),
+ INIT_REGMAP_IRQ(AXP20X, PEK_SHORT, 2, 1),
+ INIT_REGMAP_IRQ(AXP20X, PEK_LONG, 2, 0),
+ INIT_REGMAP_IRQ(AXP20X, N_OE_PWR_ON, 3, 7),
+ INIT_REGMAP_IRQ(AXP20X, N_OE_PWR_OFF, 3, 6),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_VALID, 3, 5),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_NOT_VALID, 3, 4),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_SESS_VALID, 3, 3),
+ INIT_REGMAP_IRQ(AXP20X, VBUS_SESS_END, 3, 2),
+ INIT_REGMAP_IRQ(AXP20X, LOW_PWR_LVL1, 3, 1),
+ INIT_REGMAP_IRQ(AXP20X, LOW_PWR_LVL2, 3, 0),
+ INIT_REGMAP_IRQ(AXP20X, TIMER, 4, 7),
+ INIT_REGMAP_IRQ(AXP20X, PEK_RIS_EDGE, 4, 6),
+ INIT_REGMAP_IRQ(AXP20X, PEK_FAL_EDGE, 4, 5),
+ INIT_REGMAP_IRQ(AXP20X, GPIO3_INPUT, 4, 3),
+ INIT_REGMAP_IRQ(AXP20X, GPIO2_INPUT, 4, 2),
+ INIT_REGMAP_IRQ(AXP20X, GPIO1_INPUT, 4, 1),
+ INIT_REGMAP_IRQ(AXP20X, GPIO0_INPUT, 4, 0),
+};
+
+/* some IRQs are compatible with axp20x models */
+static const struct regmap_irq axp288_regmap_irqs[] = {
+ INIT_REGMAP_IRQ(AXP288, VBUS_FALL, 0, 2),
+ INIT_REGMAP_IRQ(AXP288, VBUS_RISE, 0, 3),
+ INIT_REGMAP_IRQ(AXP288, OV, 0, 4),
+
+ INIT_REGMAP_IRQ(AXP288, DONE, 1, 2),
+ INIT_REGMAP_IRQ(AXP288, CHARGING, 1, 3),
+ INIT_REGMAP_IRQ(AXP288, SAFE_QUIT, 1, 4),
+ INIT_REGMAP_IRQ(AXP288, SAFE_ENTER, 1, 5),
+ INIT_REGMAP_IRQ(AXP288, ABSENT, 1, 6),
+ INIT_REGMAP_IRQ(AXP288, APPEND, 1, 7),
+
+ INIT_REGMAP_IRQ(AXP288, QWBTU, 2, 0),
+ INIT_REGMAP_IRQ(AXP288, WBTU, 2, 1),
+ INIT_REGMAP_IRQ(AXP288, QWBTO, 2, 2),
+ INIT_REGMAP_IRQ(AXP288, WBTO, 2, 3),
+ INIT_REGMAP_IRQ(AXP288, QCBTU, 2, 4),
+ INIT_REGMAP_IRQ(AXP288, CBTU, 2, 5),
+ INIT_REGMAP_IRQ(AXP288, QCBTO, 2, 6),
+ INIT_REGMAP_IRQ(AXP288, CBTO, 2, 7),
+
+ INIT_REGMAP_IRQ(AXP288, WL2, 3, 0),
+ INIT_REGMAP_IRQ(AXP288, WL1, 3, 1),
+ INIT_REGMAP_IRQ(AXP288, GPADC, 3, 2),
+ INIT_REGMAP_IRQ(AXP288, OT, 3, 7),
+
+ INIT_REGMAP_IRQ(AXP288, GPIO0, 4, 0),
+ INIT_REGMAP_IRQ(AXP288, GPIO1, 4, 1),
+ INIT_REGMAP_IRQ(AXP288, POKO, 4, 2),
+ INIT_REGMAP_IRQ(AXP288, POKL, 4, 3),
+ INIT_REGMAP_IRQ(AXP288, POKS, 4, 4),
+ INIT_REGMAP_IRQ(AXP288, POKN, 4, 5),
+ INIT_REGMAP_IRQ(AXP288, POKP, 4, 6),
+ INIT_REGMAP_IRQ(AXP288, TIMER, 4, 7),
+
+ INIT_REGMAP_IRQ(AXP288, MV_CHNG, 5, 0),
+ INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
};
static const struct of_device_id axp20x_of_match[] = {
};
MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id);
+static const struct acpi_device_id axp20x_acpi_match[] = {
+ {
+ .id = "INT33F4",
+ .driver_data = AXP288_ID,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(acpi, axp20x_acpi_match);
+
static const struct regmap_irq_chip axp20x_regmap_irq_chip = {
.name = "axp20x_irq_chip",
.status_base = AXP20X_IRQ1_STATE,
.ack_base = AXP20X_IRQ1_STATE,
.mask_base = AXP20X_IRQ1_EN,
- .num_regs = 5,
+ .mask_invert = true,
+ .init_ack_masked = true,
.irqs = axp20x_regmap_irqs,
.num_irqs = ARRAY_SIZE(axp20x_regmap_irqs),
+ .num_regs = 5,
+
+};
+
+static const struct regmap_irq_chip axp288_regmap_irq_chip = {
+ .name = "axp288_irq_chip",
+ .status_base = AXP20X_IRQ1_STATE,
+ .ack_base = AXP20X_IRQ1_STATE,
+ .mask_base = AXP20X_IRQ1_EN,
.mask_invert = true,
.init_ack_masked = true,
+ .irqs = axp288_regmap_irqs,
+ .num_irqs = ARRAY_SIZE(axp288_regmap_irqs),
+ .num_regs = 6,
+
};
static struct mfd_cell axp20x_cells[] = {
},
};
+static struct resource axp288_adc_resources[] = {
+ {
+ .name = "GPADC",
+ .start = AXP288_IRQ_GPADC,
+ .end = AXP288_IRQ_GPADC,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct resource axp288_charger_resources[] = {
+ {
+ .start = AXP288_IRQ_OV,
+ .end = AXP288_IRQ_OV,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_DONE,
+ .end = AXP288_IRQ_DONE,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_CHARGING,
+ .end = AXP288_IRQ_CHARGING,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_SAFE_QUIT,
+ .end = AXP288_IRQ_SAFE_QUIT,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_SAFE_ENTER,
+ .end = AXP288_IRQ_SAFE_ENTER,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_QCBTU,
+ .end = AXP288_IRQ_QCBTU,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_CBTU,
+ .end = AXP288_IRQ_CBTU,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_QCBTO,
+ .end = AXP288_IRQ_QCBTO,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = AXP288_IRQ_CBTO,
+ .end = AXP288_IRQ_CBTO,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct mfd_cell axp288_cells[] = {
+ {
+ .name = "axp288_adc",
+ .num_resources = ARRAY_SIZE(axp288_adc_resources),
+ .resources = axp288_adc_resources,
+ },
+ {
+ .name = "axp288_charger",
+ .num_resources = ARRAY_SIZE(axp288_charger_resources),
+ .resources = axp288_charger_resources,
+ },
+ {
+ .name = "axp288_battery",
+ .num_resources = ARRAY_SIZE(axp288_battery_resources),
+ .resources = axp288_battery_resources,
+ },
+};
+
static struct axp20x_dev *axp20x_pm_power_off;
static void axp20x_power_off(void)
{
+ if (axp20x_pm_power_off->variant == AXP288_ID)
+ return;
+
regmap_write(axp20x_pm_power_off->regmap, AXP20X_OFF_CTRL,
AXP20X_OFF);
}
+static int axp20x_match_device(struct axp20x_dev *axp20x, struct device *dev)
+{
+ const struct acpi_device_id *acpi_id;
+ const struct of_device_id *of_id;
+
+ if (dev->of_node) {
+ of_id = of_match_device(axp20x_of_match, dev);
+ if (!of_id) {
+ dev_err(dev, "Unable to match OF ID\n");
+ return -ENODEV;
+ }
+ axp20x->variant = (long) of_id->data;
+ } else {
+ acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev);
+ if (!acpi_id || !acpi_id->driver_data) {
+ dev_err(dev, "Unable to match ACPI ID and data\n");
+ return -ENODEV;
+ }
+ axp20x->variant = (long) acpi_id->driver_data;
+ }
+
+ switch (axp20x->variant) {
+ case AXP202_ID:
+ case AXP209_ID:
+ axp20x->nr_cells = ARRAY_SIZE(axp20x_cells);
+ axp20x->cells = axp20x_cells;
+ axp20x->regmap_cfg = &axp20x_regmap_config;
+ axp20x->regmap_irq_chip = &axp20x_regmap_irq_chip;
+ break;
+ case AXP288_ID:
+ axp20x->cells = axp288_cells;
+ axp20x->nr_cells = ARRAY_SIZE(axp288_cells);
+ axp20x->regmap_cfg = &axp288_regmap_config;
+ axp20x->regmap_irq_chip = &axp288_regmap_irq_chip;
+ break;
+ default:
+ dev_err(dev, "unsupported AXP20X ID %lu\n", axp20x->variant);
+ return -EINVAL;
+ }
+ dev_info(dev, "AXP20x variant %s found\n",
+ axp20x_model_names[axp20x->variant]);
+
+ return 0;
+}
+
static int axp20x_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
struct axp20x_dev *axp20x;
- const struct of_device_id *of_id;
int ret;
axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL);
if (!axp20x)
return -ENOMEM;
- of_id = of_match_device(axp20x_of_match, &i2c->dev);
- if (!of_id) {
- dev_err(&i2c->dev, "Unable to setup AXP20X data\n");
- return -ENODEV;
- }
- axp20x->variant = (long) of_id->data;
+ ret = axp20x_match_device(axp20x, &i2c->dev);
+ if (ret)
+ return ret;
axp20x->i2c_client = i2c;
axp20x->dev = &i2c->dev;
dev_set_drvdata(axp20x->dev, axp20x);
- axp20x->regmap = devm_regmap_init_i2c(i2c, &axp20x_regmap_config);
+ axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg);
if (IS_ERR(axp20x->regmap)) {
ret = PTR_ERR(axp20x->regmap);
dev_err(&i2c->dev, "regmap init failed: %d\n", ret);
ret = regmap_add_irq_chip(axp20x->regmap, i2c->irq,
IRQF_ONESHOT | IRQF_SHARED, -1,
- &axp20x_regmap_irq_chip,
+ axp20x->regmap_irq_chip,
&axp20x->regmap_irqc);
if (ret) {
dev_err(&i2c->dev, "failed to add irq chip: %d\n", ret);
return ret;
}
- ret = mfd_add_devices(axp20x->dev, -1, axp20x_cells,
- ARRAY_SIZE(axp20x_cells), NULL, 0, NULL);
+ ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
+ axp20x->nr_cells, NULL, 0, NULL);
if (ret) {
dev_err(&i2c->dev, "failed to add MFD devices: %d\n", ret);
.name = "axp20x",
.owner = THIS_MODULE,
.of_match_table = of_match_ptr(axp20x_of_match),
+ .acpi_match_table = ACPI_PTR(axp20x_acpi_match),
},
.probe = axp20x_i2c_probe,
.remove = axp20x_i2c_remove,
da9063->irq_base = pdata->irq_base;
} else {
da9063->flags = 0;
- da9063->irq_base = 0;
+ da9063->irq_base = -1;
}
da9063->chip_irq = irq;
return ret;
}
+ da9063->irq_base = regmap_irq_chip_get_base(da9063->regmap_irq);
+
ret = mfd_add_devices(da9063->dev, -1, da9063_devs,
ARRAY_SIZE(da9063_devs), NULL, da9063->irq_base,
NULL);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu");
if (!res) {
dev_err(&pdev->dev, "no prcmu memory region provided\n");
- return -ENOENT;
+ return -EINVAL;
}
prcmu_base = devm_ioremap(&pdev->dev, res->start, resource_size(res));
if (!prcmu_base) {
dev_err(&pdev->dev,
"failed to ioremap prcmu register memory\n");
- return -ENOENT;
+ return -ENOMEM;
}
init_prcm_registers();
dbx500_fw_version_init(pdev, pdata->version_offset);
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "prcmu-tcdm");
if (!res) {
dev_err(&pdev->dev, "no prcmu tcdm region provided\n");
- return -ENOENT;
+ return -EINVAL;
}
tcdm_base = devm_ioremap(&pdev->dev, res->start,
resource_size(res));
+ if (!tcdm_base) {
+ dev_err(&pdev->dev,
+ "failed to ioremap prcmu-tcdm register memory\n");
+ return -ENOMEM;
+ }
/* Clean up the mailbox interrupts after pre-kernel code. */
writel(ALL_MBOX_BITS, PRCM_ARM_IT1_CLR);
irq = platform_get_irq(pdev, 0);
if (irq <= 0) {
dev_err(&pdev->dev, "no prcmu irq provided\n");
- return -ENOENT;
+ return irq;
}
err = request_threaded_irq(irq, prcmu_irq_handler,
prcmu_irq_thread_fn, IRQF_NO_SUSPEND, "prcmu", NULL);
if (err < 0) {
pr_err("prcmu: Failed to allocate IRQ_DB8500_PRCMU1.\n");
- err = -EBUSY;
- goto no_irq_return;
+ return err;
}
db8500_irq_init(np);
if (err) {
mfd_remove_devices(&pdev->dev);
pr_err("prcmu: Failed to add subdevices\n");
- goto no_irq_return;
+ return err;
}
}
if (err) {
mfd_remove_devices(&pdev->dev);
pr_err("prcmu: Failed to add ab8500 subdevice\n");
- goto no_irq_return;
+ return err;
}
pr_info("DB8500 PRCMU initialized\n");
-
-no_irq_return:
return err;
}
static const struct of_device_id db8500_prcmu_match[] = {
--- /dev/null
+/*
+ * Driver for the Diolan DLN-2 USB adapter
+ *
+ * Copyright (c) 2014 Intel Corporation
+ *
+ * Derived from:
+ * i2c-diolan-u2c.c
+ * Copyright (c) 2010-2011 Ericsson AB
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/usb.h>
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/dln2.h>
+#include <linux/rculist.h>
+
+struct dln2_header {
+ __le16 size;
+ __le16 id;
+ __le16 echo;
+ __le16 handle;
+};
+
+struct dln2_response {
+ struct dln2_header hdr;
+ __le16 result;
+};
+
+#define DLN2_GENERIC_MODULE_ID 0x00
+#define DLN2_GENERIC_CMD(cmd) DLN2_CMD(cmd, DLN2_GENERIC_MODULE_ID)
+#define CMD_GET_DEVICE_VER DLN2_GENERIC_CMD(0x30)
+#define CMD_GET_DEVICE_SN DLN2_GENERIC_CMD(0x31)
+
+#define DLN2_HW_ID 0x200
+#define DLN2_USB_TIMEOUT 200 /* in ms */
+#define DLN2_MAX_RX_SLOTS 16
+#define DLN2_MAX_URBS 16
+#define DLN2_RX_BUF_SIZE 512
+
+enum dln2_handle {
+ DLN2_HANDLE_EVENT = 0, /* don't change, hardware defined */
+ DLN2_HANDLE_CTRL,
+ DLN2_HANDLE_GPIO,
+ DLN2_HANDLE_I2C,
+ DLN2_HANDLE_SPI,
+ DLN2_HANDLES
+};
+
+/*
+ * Receive context used between the receive demultiplexer and the transfer
+ * routine. While sending a request the transfer routine will look for a free
+ * receive context and use it to wait for a response and to receive the URB and
+ * thus the response data.
+ */
+struct dln2_rx_context {
+ /* completion used to wait for a response */
+ struct completion done;
+
+ /* if non-NULL the URB contains the response */
+ struct urb *urb;
+
+ /* if true then this context is used to wait for a response */
+ bool in_use;
+};
+
+/*
+ * Receive contexts for a particular DLN2 module (i2c, gpio, etc.). We use the
+ * handle header field to identify the module in dln2_dev.mod_rx_slots and then
+ * the echo header field to index the slots field and find the receive context
+ * for a particular request.
+ */
+struct dln2_mod_rx_slots {
+ /* RX slots bitmap */
+ DECLARE_BITMAP(bmap, DLN2_MAX_RX_SLOTS);
+
+ /* used to wait for a free RX slot */
+ wait_queue_head_t wq;
+
+ /* used to wait for an RX operation to complete */
+ struct dln2_rx_context slots[DLN2_MAX_RX_SLOTS];
+
+ /* avoid races between alloc/free_rx_slot and dln2_rx_transfer */
+ spinlock_t lock;
+};
+
+struct dln2_dev {
+ struct usb_device *usb_dev;
+ struct usb_interface *interface;
+ u8 ep_in;
+ u8 ep_out;
+
+ struct urb *rx_urb[DLN2_MAX_URBS];
+ void *rx_buf[DLN2_MAX_URBS];
+
+ struct dln2_mod_rx_slots mod_rx_slots[DLN2_HANDLES];
+
+ struct list_head event_cb_list;
+ spinlock_t event_cb_lock;
+
+ bool disconnect;
+ int active_transfers;
+ wait_queue_head_t disconnect_wq;
+ spinlock_t disconnect_lock;
+};
+
+struct dln2_event_cb_entry {
+ struct list_head list;
+ u16 id;
+ struct platform_device *pdev;
+ dln2_event_cb_t callback;
+};
+
+int dln2_register_event_cb(struct platform_device *pdev, u16 id,
+ dln2_event_cb_t event_cb)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i, *entry;
+ unsigned long flags;
+ int ret = 0;
+
+ entry = kzalloc(sizeof(*entry), GFP_KERNEL);
+ if (!entry)
+ return -ENOMEM;
+
+ entry->id = id;
+ entry->callback = event_cb;
+ entry->pdev = pdev;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ ret = -EBUSY;
+ break;
+ }
+ }
+
+ if (!ret)
+ list_add_rcu(&entry->list, &dln2->event_cb_list);
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (ret)
+ kfree(entry);
+
+ return ret;
+}
+EXPORT_SYMBOL(dln2_register_event_cb);
+
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 id)
+{
+ struct dln2_dev *dln2 = dev_get_drvdata(pdev->dev.parent);
+ struct dln2_event_cb_entry *i;
+ unsigned long flags;
+ bool found = false;
+
+ spin_lock_irqsave(&dln2->event_cb_lock, flags);
+
+ list_for_each_entry(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ list_del_rcu(&i->list);
+ found = true;
+ break;
+ }
+ }
+
+ spin_unlock_irqrestore(&dln2->event_cb_lock, flags);
+
+ if (found) {
+ synchronize_rcu();
+ kfree(i);
+ }
+}
+EXPORT_SYMBOL(dln2_unregister_event_cb);
+
+/*
+ * Returns true if a valid transfer slot is found. In this case the URB must not
+ * be resubmitted immediately in dln2_rx as we need the data when dln2_transfer
+ * is woke up. It will be resubmitted there.
+ */
+static bool dln2_transfer_complete(struct dln2_dev *dln2, struct urb *urb,
+ u16 handle, u16 rx_slot)
+{
+ struct device *dev = &dln2->interface->dev;
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+ struct dln2_rx_context *rxc;
+ bool valid_slot = false;
+
+ if (rx_slot >= DLN2_MAX_RX_SLOTS)
+ goto out;
+
+ rxc = &rxs->slots[rx_slot];
+
+ /*
+ * No need to disable interrupts as this lock is not taken in interrupt
+ * context elsewhere in this driver. This function (or its callers) are
+ * also not exported to other modules.
+ */
+ spin_lock(&rxs->lock);
+ if (rxc->in_use && !rxc->urb) {
+ rxc->urb = urb;
+ complete(&rxc->done);
+ valid_slot = true;
+ }
+ spin_unlock(&rxs->lock);
+
+out:
+ if (!valid_slot)
+ dev_warn(dev, "bad/late response %d/%d\n", handle, rx_slot);
+
+ return valid_slot;
+}
+
+static void dln2_run_event_callbacks(struct dln2_dev *dln2, u16 id, u16 echo,
+ void *data, int len)
+{
+ struct dln2_event_cb_entry *i;
+
+ rcu_read_lock();
+
+ list_for_each_entry_rcu(i, &dln2->event_cb_list, list) {
+ if (i->id == id) {
+ i->callback(i->pdev, echo, data, len);
+ break;
+ }
+ }
+
+ rcu_read_unlock();
+}
+
+static void dln2_rx(struct urb *urb)
+{
+ struct dln2_dev *dln2 = urb->context;
+ struct dln2_header *hdr = urb->transfer_buffer;
+ struct device *dev = &dln2->interface->dev;
+ u16 id, echo, handle, size;
+ u8 *data;
+ int len;
+ int err;
+
+ switch (urb->status) {
+ case 0:
+ /* success */
+ break;
+ case -ECONNRESET:
+ case -ENOENT:
+ case -ESHUTDOWN:
+ case -EPIPE:
+ /* this urb is terminated, clean up */
+ dev_dbg(dev, "urb shutting down with status %d\n", urb->status);
+ return;
+ default:
+ dev_dbg(dev, "nonzero urb status received %d\n", urb->status);
+ goto out;
+ }
+
+ if (urb->actual_length < sizeof(struct dln2_header)) {
+ dev_err(dev, "short response: %d\n", urb->actual_length);
+ goto out;
+ }
+
+ handle = le16_to_cpu(hdr->handle);
+ id = le16_to_cpu(hdr->id);
+ echo = le16_to_cpu(hdr->echo);
+ size = le16_to_cpu(hdr->size);
+
+ if (size != urb->actual_length) {
+ dev_err(dev, "size mismatch: handle %x cmd %x echo %x size %d actual %d\n",
+ handle, id, echo, size, urb->actual_length);
+ goto out;
+ }
+
+ if (handle >= DLN2_HANDLES) {
+ dev_warn(dev, "invalid handle %d\n", handle);
+ goto out;
+ }
+
+ data = urb->transfer_buffer + sizeof(struct dln2_header);
+ len = urb->actual_length - sizeof(struct dln2_header);
+
+ if (handle == DLN2_HANDLE_EVENT) {
+ dln2_run_event_callbacks(dln2, id, echo, data, len);
+ } else {
+ /* URB will be re-submitted in _dln2_transfer (free_rx_slot) */
+ if (dln2_transfer_complete(dln2, urb, handle, echo))
+ return;
+ }
+
+out:
+ err = usb_submit_urb(urb, GFP_ATOMIC);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+}
+
+static void *dln2_prep_buf(u16 handle, u16 cmd, u16 echo, const void *obuf,
+ int *obuf_len, gfp_t gfp)
+{
+ int len;
+ void *buf;
+ struct dln2_header *hdr;
+
+ len = *obuf_len + sizeof(*hdr);
+ buf = kmalloc(len, gfp);
+ if (!buf)
+ return NULL;
+
+ hdr = (struct dln2_header *)buf;
+ hdr->id = cpu_to_le16(cmd);
+ hdr->size = cpu_to_le16(len);
+ hdr->echo = cpu_to_le16(echo);
+ hdr->handle = cpu_to_le16(handle);
+
+ memcpy(buf + sizeof(*hdr), obuf, *obuf_len);
+
+ *obuf_len = len;
+
+ return buf;
+}
+
+static int dln2_send_wait(struct dln2_dev *dln2, u16 handle, u16 cmd, u16 echo,
+ const void *obuf, int obuf_len)
+{
+ int ret = 0;
+ int len = obuf_len;
+ void *buf;
+ int actual;
+
+ buf = dln2_prep_buf(handle, cmd, echo, obuf, &len, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = usb_bulk_msg(dln2->usb_dev,
+ usb_sndbulkpipe(dln2->usb_dev, dln2->ep_out),
+ buf, len, &actual, DLN2_USB_TIMEOUT);
+
+ kfree(buf);
+
+ return ret;
+}
+
+static bool find_free_slot(struct dln2_dev *dln2, u16 handle, int *slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ unsigned long flags;
+
+ if (dln2->disconnect) {
+ *slot = -ENODEV;
+ return true;
+ }
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ *slot = find_first_zero_bit(rxs->bmap, DLN2_MAX_RX_SLOTS);
+
+ if (*slot < DLN2_MAX_RX_SLOTS) {
+ struct dln2_rx_context *rxc = &rxs->slots[*slot];
+
+ set_bit(*slot, rxs->bmap);
+ rxc->in_use = true;
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ return *slot < DLN2_MAX_RX_SLOTS;
+}
+
+static int alloc_rx_slot(struct dln2_dev *dln2, u16 handle)
+{
+ int ret;
+ int slot;
+
+ /*
+ * No need to timeout here, the wait is bounded by the timeout in
+ * _dln2_transfer.
+ */
+ ret = wait_event_interruptible(dln2->mod_rx_slots[handle].wq,
+ find_free_slot(dln2, handle, &slot));
+ if (ret < 0)
+ return ret;
+
+ return slot;
+}
+
+static void free_rx_slot(struct dln2_dev *dln2, u16 handle, int slot)
+{
+ struct dln2_mod_rx_slots *rxs;
+ struct urb *urb = NULL;
+ unsigned long flags;
+ struct dln2_rx_context *rxc;
+
+ rxs = &dln2->mod_rx_slots[handle];
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ clear_bit(slot, rxs->bmap);
+
+ rxc = &rxs->slots[slot];
+ rxc->in_use = false;
+ urb = rxc->urb;
+ rxc->urb = NULL;
+ reinit_completion(&rxc->done);
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+
+ if (urb) {
+ int err;
+ struct device *dev = &dln2->interface->dev;
+
+ err = usb_submit_urb(urb, GFP_KERNEL);
+ if (err < 0)
+ dev_err(dev, "failed to resubmit RX URB: %d\n", err);
+ }
+
+ wake_up_interruptible(&rxs->wq);
+}
+
+static int _dln2_transfer(struct dln2_dev *dln2, u16 handle, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len)
+{
+ int ret = 0;
+ int rx_slot;
+ struct dln2_response *rsp;
+ struct dln2_rx_context *rxc;
+ struct device *dev = &dln2->interface->dev;
+ const unsigned long timeout = DLN2_USB_TIMEOUT * HZ / 1000;
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[handle];
+ int size;
+
+ spin_lock(&dln2->disconnect_lock);
+ if (!dln2->disconnect)
+ dln2->active_transfers++;
+ else
+ ret = -ENODEV;
+ spin_unlock(&dln2->disconnect_lock);
+
+ if (ret)
+ return ret;
+
+ rx_slot = alloc_rx_slot(dln2, handle);
+ if (rx_slot < 0) {
+ ret = rx_slot;
+ goto out_decr;
+ }
+
+ ret = dln2_send_wait(dln2, handle, cmd, rx_slot, obuf, obuf_len);
+ if (ret < 0) {
+ dev_err(dev, "USB write failed: %d\n", ret);
+ goto out_free_rx_slot;
+ }
+
+ rxc = &rxs->slots[rx_slot];
+
+ ret = wait_for_completion_interruptible_timeout(&rxc->done, timeout);
+ if (ret <= 0) {
+ if (!ret)
+ ret = -ETIMEDOUT;
+ goto out_free_rx_slot;
+ } else {
+ ret = 0;
+ }
+
+ if (dln2->disconnect) {
+ ret = -ENODEV;
+ goto out_free_rx_slot;
+ }
+
+ /* if we got here we know that the response header has been checked */
+ rsp = rxc->urb->transfer_buffer;
+ size = le16_to_cpu(rsp->hdr.size);
+
+ if (size < sizeof(*rsp)) {
+ ret = -EPROTO;
+ goto out_free_rx_slot;
+ }
+
+ if (le16_to_cpu(rsp->result) > 0x80) {
+ dev_dbg(dev, "%d received response with error %d\n",
+ handle, le16_to_cpu(rsp->result));
+ ret = -EREMOTEIO;
+ goto out_free_rx_slot;
+ }
+
+ if (!ibuf)
+ goto out_free_rx_slot;
+
+ if (*ibuf_len > size - sizeof(*rsp))
+ *ibuf_len = size - sizeof(*rsp);
+
+ memcpy(ibuf, rsp + 1, *ibuf_len);
+
+out_free_rx_slot:
+ free_rx_slot(dln2, handle, rx_slot);
+out_decr:
+ spin_lock(&dln2->disconnect_lock);
+ dln2->active_transfers--;
+ spin_unlock(&dln2->disconnect_lock);
+ if (dln2->disconnect)
+ wake_up(&dln2->disconnect_wq);
+
+ return ret;
+}
+
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len)
+{
+ struct dln2_platform_data *dln2_pdata;
+ struct dln2_dev *dln2;
+ u16 handle;
+
+ dln2 = dev_get_drvdata(pdev->dev.parent);
+ dln2_pdata = dev_get_platdata(&pdev->dev);
+ handle = dln2_pdata->handle;
+
+ return _dln2_transfer(dln2, handle, cmd, obuf, obuf_len, ibuf,
+ ibuf_len);
+}
+EXPORT_SYMBOL(dln2_transfer);
+
+static int dln2_check_hw(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 hw_type;
+ int len = sizeof(hw_type);
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_VER,
+ NULL, 0, &hw_type, &len);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(hw_type))
+ return -EREMOTEIO;
+
+ if (le32_to_cpu(hw_type) != DLN2_HW_ID) {
+ dev_err(&dln2->interface->dev, "Device ID 0x%x not supported\n",
+ le32_to_cpu(hw_type));
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int dln2_print_serialno(struct dln2_dev *dln2)
+{
+ int ret;
+ __le32 serial_no;
+ int len = sizeof(serial_no);
+ struct device *dev = &dln2->interface->dev;
+
+ ret = _dln2_transfer(dln2, DLN2_HANDLE_CTRL, CMD_GET_DEVICE_SN, NULL, 0,
+ &serial_no, &len);
+ if (ret < 0)
+ return ret;
+ if (len < sizeof(serial_no))
+ return -EREMOTEIO;
+
+ dev_info(dev, "Diolan DLN2 serial %u\n", le32_to_cpu(serial_no));
+
+ return 0;
+}
+
+static int dln2_hw_init(struct dln2_dev *dln2)
+{
+ int ret;
+
+ ret = dln2_check_hw(dln2);
+ if (ret < 0)
+ return ret;
+
+ return dln2_print_serialno(dln2);
+}
+
+static void dln2_free_rx_urbs(struct dln2_dev *dln2)
+{
+ int i;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ usb_kill_urb(dln2->rx_urb[i]);
+ usb_free_urb(dln2->rx_urb[i]);
+ kfree(dln2->rx_buf[i]);
+ }
+}
+
+static void dln2_free(struct dln2_dev *dln2)
+{
+ dln2_free_rx_urbs(dln2);
+ usb_put_dev(dln2->usb_dev);
+ kfree(dln2);
+}
+
+static int dln2_setup_rx_urbs(struct dln2_dev *dln2,
+ struct usb_host_interface *hostif)
+{
+ int i;
+ int ret;
+ const int rx_max_size = DLN2_RX_BUF_SIZE;
+ struct device *dev = &dln2->interface->dev;
+
+ for (i = 0; i < DLN2_MAX_URBS; i++) {
+ dln2->rx_buf[i] = kmalloc(rx_max_size, GFP_KERNEL);
+ if (!dln2->rx_buf[i])
+ return -ENOMEM;
+
+ dln2->rx_urb[i] = usb_alloc_urb(0, GFP_KERNEL);
+ if (!dln2->rx_urb[i])
+ return -ENOMEM;
+
+ usb_fill_bulk_urb(dln2->rx_urb[i], dln2->usb_dev,
+ usb_rcvbulkpipe(dln2->usb_dev, dln2->ep_in),
+ dln2->rx_buf[i], rx_max_size, dln2_rx, dln2);
+
+ ret = usb_submit_urb(dln2->rx_urb[i], GFP_KERNEL);
+ if (ret < 0) {
+ dev_err(dev, "failed to submit RX URB: %d\n", ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static struct dln2_platform_data dln2_pdata_gpio = {
+ .handle = DLN2_HANDLE_GPIO,
+};
+
+/* Only one I2C port seems to be supported on current hardware */
+static struct dln2_platform_data dln2_pdata_i2c = {
+ .handle = DLN2_HANDLE_I2C,
+ .port = 0,
+};
+
+/* Only one SPI port supported */
+static struct dln2_platform_data dln2_pdata_spi = {
+ .handle = DLN2_HANDLE_SPI,
+ .port = 0,
+};
+
+static const struct mfd_cell dln2_devs[] = {
+ {
+ .name = "dln2-gpio",
+ .platform_data = &dln2_pdata_gpio,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+ {
+ .name = "dln2-i2c",
+ .platform_data = &dln2_pdata_i2c,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+ {
+ .name = "dln2-spi",
+ .platform_data = &dln2_pdata_spi,
+ .pdata_size = sizeof(struct dln2_platform_data),
+ },
+};
+
+static void dln2_disconnect(struct usb_interface *interface)
+{
+ struct dln2_dev *dln2 = usb_get_intfdata(interface);
+ int i, j;
+
+ /* don't allow starting new transfers */
+ spin_lock(&dln2->disconnect_lock);
+ dln2->disconnect = true;
+ spin_unlock(&dln2->disconnect_lock);
+
+ /* cancel in progress transfers */
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ struct dln2_mod_rx_slots *rxs = &dln2->mod_rx_slots[i];
+ unsigned long flags;
+
+ spin_lock_irqsave(&rxs->lock, flags);
+
+ /* cancel all response waiters */
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++) {
+ struct dln2_rx_context *rxc = &rxs->slots[j];
+
+ if (rxc->in_use)
+ complete(&rxc->done);
+ }
+
+ spin_unlock_irqrestore(&rxs->lock, flags);
+ }
+
+ /* wait for transfers to end */
+ wait_event(dln2->disconnect_wq, !dln2->active_transfers);
+
+ mfd_remove_devices(&interface->dev);
+
+ dln2_free(dln2);
+}
+
+static int dln2_probe(struct usb_interface *interface,
+ const struct usb_device_id *usb_id)
+{
+ struct usb_host_interface *hostif = interface->cur_altsetting;
+ struct device *dev = &interface->dev;
+ struct dln2_dev *dln2;
+ int ret;
+ int i, j;
+
+ if (hostif->desc.bInterfaceNumber != 0 ||
+ hostif->desc.bNumEndpoints < 2)
+ return -ENODEV;
+
+ dln2 = kzalloc(sizeof(*dln2), GFP_KERNEL);
+ if (!dln2)
+ return -ENOMEM;
+
+ dln2->ep_out = hostif->endpoint[0].desc.bEndpointAddress;
+ dln2->ep_in = hostif->endpoint[1].desc.bEndpointAddress;
+ dln2->usb_dev = usb_get_dev(interface_to_usbdev(interface));
+ dln2->interface = interface;
+ usb_set_intfdata(interface, dln2);
+ init_waitqueue_head(&dln2->disconnect_wq);
+
+ for (i = 0; i < DLN2_HANDLES; i++) {
+ init_waitqueue_head(&dln2->mod_rx_slots[i].wq);
+ spin_lock_init(&dln2->mod_rx_slots[i].lock);
+ for (j = 0; j < DLN2_MAX_RX_SLOTS; j++)
+ init_completion(&dln2->mod_rx_slots[i].slots[j].done);
+ }
+
+ spin_lock_init(&dln2->event_cb_lock);
+ spin_lock_init(&dln2->disconnect_lock);
+ INIT_LIST_HEAD(&dln2->event_cb_list);
+
+ ret = dln2_setup_rx_urbs(dln2, hostif);
+ if (ret)
+ goto out_cleanup;
+
+ ret = dln2_hw_init(dln2);
+ if (ret < 0) {
+ dev_err(dev, "failed to initialize hardware\n");
+ goto out_cleanup;
+ }
+
+ ret = mfd_add_hotplug_devices(dev, dln2_devs, ARRAY_SIZE(dln2_devs));
+ if (ret != 0) {
+ dev_err(dev, "failed to add mfd devices to core\n");
+ goto out_cleanup;
+ }
+
+ return 0;
+
+out_cleanup:
+ dln2_free(dln2);
+
+ return ret;
+}
+
+static const struct usb_device_id dln2_table[] = {
+ { USB_DEVICE(0xa257, 0x2013) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(usb, dln2_table);
+
+static struct usb_driver dln2_driver = {
+ .name = "dln2",
+ .probe = dln2_probe,
+ .disconnect = dln2_disconnect,
+ .id_table = dln2_table,
+};
+
+module_usb_driver(dln2_driver);
+
+MODULE_AUTHOR("Octavian Purdila <octavian.purdila@intel.com>");
+MODULE_DESCRIPTION("Core driver for the Diolan DLN2 interface adapter");
+MODULE_LICENSE("GPL v2");
return -ENODEV;
}
- ret = mfd_add_devices(&dev->dev, 0, lpc_sch_cells, cells, NULL, 0, NULL);
- if (ret)
- mfd_remove_devices(&dev->dev);
-
- return ret;
+ return mfd_add_devices(&dev->dev, 0, lpc_sch_cells, cells, NULL, 0, NULL);
}
static void lpc_sch_remove(struct pci_dev *dev)
/*
* max14577.c - mfd core driver for the Maxim 14577/77836
*
- * Copyright (C) 2014 Samsung Electrnoics
+ * Copyright (C) 2014 Samsung Electronics
* Chanwoo Choi <cw00.choi@samsung.com>
* Krzysztof Kozlowski <k.kozlowski@samsung.com>
*
static const struct mfd_cell max77693_devs[] = {
{ .name = "max77693-pmic", },
- { .name = "max77693-charger", },
+ {
+ .name = "max77693-charger",
+ .of_compatible = "maxim,max77693-charger",
+ },
{ .name = "max77693-muic", },
- { .name = "max77693-haptic", },
+ {
+ .name = "max77693-haptic",
+ .of_compatible = "maxim,max77693-haptic",
+ },
{
.name = "max77693-flash",
.of_compatible = "maxim,max77693-flash",
.num_irqs = ARRAY_SIZE(max77693_muic_irqs),
};
+static const struct regmap_config max77693_regmap_haptic_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX77693_HAPTIC_REG_END,
+};
+
static int max77693_i2c_probe(struct i2c_client *i2c,
const struct i2c_device_id *id)
{
}
i2c_set_clientdata(max77693->haptic, max77693);
+ max77693->regmap_haptic = devm_regmap_init_i2c(max77693->haptic,
+ &max77693_regmap_haptic_config);
+ if (IS_ERR(max77693->regmap_haptic)) {
+ ret = PTR_ERR(max77693->regmap_haptic);
+ dev_err(max77693->dev,
+ "failed to initialize haptic register map: %d\n", ret);
+ goto err_regmap;
+ }
+
/*
* Initialize register map for MUIC device because use regmap-muic
* instance of MUIC device when irq of max77693 is initialized
ret = PTR_ERR(max77693->regmap_muic);
dev_err(max77693->dev,
"failed to allocate register map: %d\n", ret);
- goto err_regmap_muic;
+ goto err_regmap;
}
ret = regmap_add_irq_chip(max77693->regmap, max77693->irq,
&max77693->irq_data_led);
if (ret) {
dev_err(max77693->dev, "failed to add irq chip: %d\n", ret);
- goto err_regmap_muic;
+ goto err_regmap;
}
ret = regmap_add_irq_chip(max77693->regmap, max77693->irq,
regmap_del_irq_chip(max77693->irq, max77693->irq_data_topsys);
err_irq_topsys:
regmap_del_irq_chip(max77693->irq, max77693->irq_data_led);
-err_regmap_muic:
+err_regmap:
i2c_unregister_device(max77693->haptic);
err_i2c_haptic:
i2c_unregister_device(max77693->muic);
struct platform_device *pdev;
struct device_node *np = NULL;
int ret = -ENOMEM;
+ int platform_id;
int r;
- pdev = platform_device_alloc(cell->name, id + cell->id);
+ if (id < 0)
+ platform_id = id;
+ else
+ platform_id = id + cell->id;
+
+ pdev = platform_device_alloc(cell->name, platform_id);
if (!pdev)
goto fail_alloc;
static int rts5227_optimize_phy(struct rtsx_pcr *pcr)
{
+ int err;
+
+ err = rtsx_gops_pm_reset(pcr);
+ if (err < 0)
+ return err;
+
/* Optimize RX sensitivity */
return rtsx_pci_write_phy_register(pcr, 0x00, 0xBA42);
}
{
int err;
+ err = rtsx_gops_pm_reset(pcr);
+ if (err < 0)
+ return err;
+
err = rtsx_pci_write_phy_register(pcr, PHY_REG_REV,
PHY_REG_REV_RESV | PHY_REG_REV_RXIDLE_LATCHED |
PHY_REG_REV_P1_EN | PHY_REG_REV_RXIDLE_EN |
--- /dev/null
+/* Driver for Realtek PCI-Express card reader
+ *
+ * Copyright(c) 2009-2013 Realtek Semiconductor Corp. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2, or (at your option) any
+ * later version.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, see <http://www.gnu.org/licenses/>.
+ *
+ * Author:
+ * Micky Ching <micky_ching@realsil.com.cn>
+ */
+
+#include <linux/mfd/rtsx_pci.h>
+#include "rtsx_pcr.h"
+
+int rtsx_gops_pm_reset(struct rtsx_pcr *pcr)
+{
+ int err;
+
+ /* init aspm */
+ rtsx_pci_write_register(pcr, ASPM_FORCE_CTL, 0xFF, 0x00);
+ err = rtsx_pci_update_cfg_byte(pcr, LCTLR, ~LCTLR_ASPM_CTL_MASK, 0x00);
+ if (err < 0)
+ return err;
+
+ /* reset PM_CTRL3 before send buffer cmd */
+ return rtsx_pci_write_register(pcr, PM_CTRL3, D3_DELINK_MODE_EN, 0x00);
+}
pcr->ms_pull_ctl_disable_tbl = __device##_ms_pull_ctl_disable_tbl; \
} while (0)
+/* generic operations */
+int rtsx_gops_pm_reset(struct rtsx_pcr *pcr);
+
#endif
/* initialize USB SG transfer timer */
setup_timer(&ucr->sg_timer, rtsx_usb_sg_timed_out, (unsigned long) ucr);
- ret = mfd_add_devices(&intf->dev, usb_dev->devnum, rtsx_usb_cells,
- ARRAY_SIZE(rtsx_usb_cells), NULL, 0, NULL);
+ ret = mfd_add_hotplug_devices(&intf->dev, rtsx_usb_cells,
+ ARRAY_SIZE(rtsx_usb_cells));
if (ret)
goto out_init_fail;
#include <linux/mfd/samsung/irq.h>
#include <linux/mfd/samsung/s2mpa01.h>
#include <linux/mfd/samsung/s2mps11.h>
+#include <linux/mfd/samsung/s2mps13.h>
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mpu02.h>
#include <linux/mfd/samsung/s5m8763.h>
#include <linux/mfd/samsung/s5m8767.h>
-#include <linux/regulator/machine.h>
#include <linux/regmap.h>
static const struct mfd_cell s5m8751_devs[] = {
}
};
+static const struct mfd_cell s2mps13_devs[] = {
+ { .name = "s2mps13-pmic", },
+ { .name = "s2mps13-rtc", },
+ {
+ .name = "s2mps13-clk",
+ .of_compatible = "samsung,s2mps13-clk",
+ },
+};
+
static const struct mfd_cell s2mps14_devs[] = {
{
.name = "s2mps14-pmic",
}, {
.compatible = "samsung,s2mps11-pmic",
.data = (void *)S2MPS11X,
+ }, {
+ .compatible = "samsung,s2mps13-pmic",
+ .data = (void *)S2MPS13X,
}, {
.compatible = "samsung,s2mps14-pmic",
.data = (void *)S2MPS14X,
.cache_type = REGCACHE_FLAT,
};
+static const struct regmap_config s2mps13_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = S2MPS13_REG_LDODSCH5,
+ .volatile_reg = s2mps11_volatile,
+ .cache_type = REGCACHE_FLAT,
+};
+
static const struct regmap_config s2mps14_regmap_config = {
.reg_bits = 8,
.val_bits = 8,
case S2MPS11X:
regmap = &s2mps11_regmap_config;
break;
+ case S2MPS13X:
+ regmap = &s2mps13_regmap_config;
+ break;
case S2MPS14X:
regmap = &s2mps14_regmap_config;
break;
sec_devs = s2mps11_devs;
num_sec_devs = ARRAY_SIZE(s2mps11_devs);
break;
+ case S2MPS13X:
+ sec_devs = s2mps13_devs;
+ num_sec_devs = ARRAY_SIZE(s2mps13_devs);
+ break;
case S2MPS14X:
sec_devs = s2mps14_devs;
num_sec_devs = ARRAY_SIZE(s2mps14_devs);
*/
disable_irq(sec_pmic->irq);
- switch (sec_pmic->device_type) {
- case S2MPS14X:
- case S2MPU02:
- regulator_suspend_prepare(PM_SUSPEND_MEM);
- break;
- default:
- break;
- }
-
return 0;
}
.ack_base = S2MPS11_REG_INT1,
};
+#define S2MPS1X_IRQ_CHIP_COMMON_DATA \
+ .irqs = s2mps14_irqs, \
+ .num_irqs = ARRAY_SIZE(s2mps14_irqs), \
+ .num_regs = 3, \
+ .status_base = S2MPS14_REG_INT1, \
+ .mask_base = S2MPS14_REG_INT1M, \
+ .ack_base = S2MPS14_REG_INT1 \
+
+static const struct regmap_irq_chip s2mps13_irq_chip = {
+ .name = "s2mps13",
+ S2MPS1X_IRQ_CHIP_COMMON_DATA,
+};
+
static const struct regmap_irq_chip s2mps14_irq_chip = {
.name = "s2mps14",
- .irqs = s2mps14_irqs,
- .num_irqs = ARRAY_SIZE(s2mps14_irqs),
- .num_regs = 3,
- .status_base = S2MPS14_REG_INT1,
- .mask_base = S2MPS14_REG_INT1M,
- .ack_base = S2MPS14_REG_INT1,
+ S2MPS1X_IRQ_CHIP_COMMON_DATA,
};
static const struct regmap_irq_chip s2mpu02_irq_chip = {
case S2MPS11X:
sec_irq_chip = &s2mps11_irq_chip;
break;
+ case S2MPS13X:
+ sec_irq_chip = &s2mps13_irq_chip;
+ break;
case S2MPS14X:
sec_irq_chip = &s2mps14_irq_chip;
break;
#include <linux/err.h>
#include <linux/io.h>
#include <linux/module.h>
+#include <linux/list.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_platform.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
#include <linux/mfd/syscon.h>
+#include <linux/slab.h>
static struct platform_driver syscon_driver;
+static DEFINE_SPINLOCK(syscon_list_slock);
+static LIST_HEAD(syscon_list);
+
struct syscon {
+ struct device_node *np;
struct regmap *regmap;
+ struct list_head list;
+};
+
+static struct regmap_config syscon_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
};
-static int syscon_match_node(struct device *dev, void *data)
+static struct syscon *of_syscon_register(struct device_node *np)
{
- struct device_node *dn = data;
+ struct syscon *syscon;
+ struct regmap *regmap;
+ void __iomem *base;
+ int ret;
+ struct regmap_config syscon_config = syscon_regmap_config;
+
+ if (!of_device_is_compatible(np, "syscon"))
+ return ERR_PTR(-EINVAL);
+
+ syscon = kzalloc(sizeof(*syscon), GFP_KERNEL);
+ if (!syscon)
+ return ERR_PTR(-ENOMEM);
+
+ base = of_iomap(np, 0);
+ if (!base) {
+ ret = -ENOMEM;
+ goto err_map;
+ }
+
+ /* Parse the device's DT node for an endianness specification */
+ if (of_property_read_bool(np, "big-endian"))
+ syscon_config.val_format_endian = REGMAP_ENDIAN_BIG;
+ else if (of_property_read_bool(np, "little-endian"))
+ syscon_config.val_format_endian = REGMAP_ENDIAN_LITTLE;
+
+ regmap = regmap_init_mmio(NULL, base, &syscon_config);
+ if (IS_ERR(regmap)) {
+ pr_err("regmap init failed\n");
+ ret = PTR_ERR(regmap);
+ goto err_regmap;
+ }
+
+ syscon->regmap = regmap;
+ syscon->np = np;
+
+ spin_lock(&syscon_list_slock);
+ list_add_tail(&syscon->list, &syscon_list);
+ spin_unlock(&syscon_list_slock);
- return (dev->of_node == dn) ? 1 : 0;
+ return syscon;
+
+err_regmap:
+ iounmap(base);
+err_map:
+ kfree(syscon);
+ return ERR_PTR(ret);
}
struct regmap *syscon_node_to_regmap(struct device_node *np)
{
- struct syscon *syscon;
- struct device *dev;
+ struct syscon *entry, *syscon = NULL;
- dev = driver_find_device(&syscon_driver.driver, NULL, np,
- syscon_match_node);
- if (!dev)
- return ERR_PTR(-EPROBE_DEFER);
+ spin_lock(&syscon_list_slock);
- syscon = dev_get_drvdata(dev);
+ list_for_each_entry(entry, &syscon_list, list)
+ if (entry->np == np) {
+ syscon = entry;
+ break;
+ }
+
+ spin_unlock(&syscon_list_slock);
+
+ if (!syscon)
+ syscon = of_syscon_register(np);
+
+ if (IS_ERR(syscon))
+ return ERR_CAST(syscon);
return syscon->regmap;
}
}
EXPORT_SYMBOL_GPL(syscon_regmap_lookup_by_phandle);
-static const struct of_device_id of_syscon_match[] = {
- { .compatible = "syscon", },
- { },
-};
-
-static struct regmap_config syscon_regmap_config = {
- .reg_bits = 32,
- .val_bits = 32,
- .reg_stride = 4,
-};
-
static int syscon_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
.driver = {
.name = "syscon",
.owner = THIS_MODULE,
- .of_match_table = of_syscon_match,
},
.probe = syscon_probe,
.id_table = syscon_ids,
unsigned long flags;
u8 dev_ctl;
- clk_enable(t7l66xb->clk32k);
+ clk_prepare_enable(t7l66xb->clk32k);
spin_lock_irqsave(&t7l66xb->lock, flags);
spin_unlock_irqrestore(&t7l66xb->lock, flags);
- clk_disable(t7l66xb->clk32k);
+ clk_disable_unprepare(t7l66xb->clk32k);
return 0;
}
if (pdata && pdata->suspend)
pdata->suspend(dev);
- clk_disable(t7l66xb->clk48m);
+ clk_disable_unprepare(t7l66xb->clk48m);
return 0;
}
struct t7l66xb *t7l66xb = platform_get_drvdata(dev);
struct t7l66xb_platform_data *pdata = dev_get_platdata(&dev->dev);
- clk_enable(t7l66xb->clk48m);
+ clk_prepare_enable(t7l66xb->clk48m);
if (pdata && pdata->resume)
pdata->resume(dev);
goto err_ioremap;
}
- clk_enable(t7l66xb->clk48m);
+ clk_prepare_enable(t7l66xb->clk48m);
if (pdata && pdata->enable)
pdata->enable(dev);
int ret;
ret = pdata->disable(dev);
- clk_disable(t7l66xb->clk48m);
+ clk_disable_unprepare(t7l66xb->clk48m);
clk_put(t7l66xb->clk48m);
- clk_disable(t7l66xb->clk32k);
+ clk_disable_unprepare(t7l66xb->clk32k);
clk_put(t7l66xb->clk32k);
t7l66xb_detach_irq(dev);
iounmap(t7l66xb->scr);
static int tc3589x_irq_init(struct tc3589x *tc3589x, struct device_node *np)
{
- int base = tc3589x->irq_base;
-
tc3589x->domain = irq_domain_add_simple(
- np, TC3589x_NR_INTERNAL_IRQS, base,
+ np, TC3589x_NR_INTERNAL_IRQS, 0,
&tc3589x_irq_ops, tc3589x);
if (!tc3589x->domain) {
if (blocks & TC3589x_BLOCK_GPIO) {
ret = mfd_add_devices(tc3589x->dev, -1, tc3589x_dev_gpio,
ARRAY_SIZE(tc3589x_dev_gpio), NULL,
- tc3589x->irq_base, tc3589x->domain);
+ 0, tc3589x->domain);
if (ret) {
dev_err(tc3589x->dev, "failed to add gpio child\n");
return ret;
if (blocks & TC3589x_BLOCK_KEYPAD) {
ret = mfd_add_devices(tc3589x->dev, -1, tc3589x_dev_keypad,
ARRAY_SIZE(tc3589x_dev_keypad), NULL,
- tc3589x->irq_base, tc3589x->domain);
+ 0, tc3589x->domain);
if (ret) {
dev_err(tc3589x->dev, "failed to keypad child\n");
return ret;
tc3589x->dev = &i2c->dev;
tc3589x->i2c = i2c;
tc3589x->pdata = pdata;
- tc3589x->irq_base = pdata->irq_base;
switch (version) {
case TC3589X_TC35893:
if (pdata && pdata->suspend)
pdata->suspend(dev);
- clk_disable(tc6387xb->clk32k);
+ clk_disable_unprepare(tc6387xb->clk32k);
return 0;
}
struct tc6387xb *tc6387xb = platform_get_drvdata(dev);
struct tc6387xb_platform_data *pdata = dev_get_platdata(&dev->dev);
- clk_enable(tc6387xb->clk32k);
+ clk_prepare_enable(tc6387xb->clk32k);
if (pdata && pdata->resume)
pdata->resume(dev);
struct platform_device *dev = to_platform_device(mmc->dev.parent);
struct tc6387xb *tc6387xb = platform_get_drvdata(dev);
- clk_enable(tc6387xb->clk32k);
+ clk_prepare_enable(tc6387xb->clk32k);
tmio_core_mmc_enable(tc6387xb->scr + 0x200, 0,
tc6387xb_mmc_resources[0].start & 0xfffe);
struct platform_device *dev = to_platform_device(mmc->dev.parent);
struct tc6387xb *tc6387xb = platform_get_drvdata(dev);
- clk_disable(tc6387xb->clk32k);
+ clk_disable_unprepare(tc6387xb->clk32k);
return 0;
}
mfd_remove_devices(&dev->dev);
iounmap(tc6387xb->scr);
release_resource(&tc6387xb->rscr);
- clk_disable(tc6387xb->clk32k);
+ clk_disable_unprepare(tc6387xb->clk32k);
clk_put(tc6387xb->clk32k);
kfree(tc6387xb);
return 0;
}
+static int tc6393xb_ohci_suspend(struct platform_device *dev)
+{
+ struct tc6393xb_platform_data *tcpd = dev_get_platdata(dev->dev.parent);
+
+ /* We can't properly store/restore OHCI state, so fail here */
+ if (tcpd->resume_restore)
+ return -EBUSY;
+
+ return tc6393xb_ohci_disable(dev);
+}
+
static int tc6393xb_fb_enable(struct platform_device *dev)
{
struct tc6393xb *tc6393xb = dev_get_drvdata(dev->dev.parent);
.num_resources = ARRAY_SIZE(tc6393xb_ohci_resources),
.resources = tc6393xb_ohci_resources,
.enable = tc6393xb_ohci_enable,
- .suspend = tc6393xb_ohci_disable,
+ .suspend = tc6393xb_ohci_suspend,
.resume = tc6393xb_ohci_enable,
.disable = tc6393xb_ohci_disable,
},
goto err_ioremap;
}
- ret = clk_enable(tc6393xb->clk);
+ ret = clk_prepare_enable(tc6393xb->clk);
if (ret)
goto err_clk_enable;
gpiochip_remove(&tc6393xb->gpio);
tcpd->disable(dev);
err_enable:
- clk_disable(tc6393xb->clk);
+ clk_disable_unprepare(tc6393xb->clk);
err_clk_enable:
iounmap(tc6393xb->scr);
err_ioremap:
gpiochip_remove(&tc6393xb->gpio);
ret = tcpd->disable(dev);
- clk_disable(tc6393xb->clk);
+ clk_disable_unprepare(tc6393xb->clk);
iounmap(tc6393xb->scr);
release_resource(&tc6393xb->rscr);
clk_put(tc6393xb->clk);
ioread8(tc6393xb->scr + SCR_GPI_BCR(i));
}
ret = tcpd->suspend(dev);
- clk_disable(tc6393xb->clk);
+ clk_disable_unprepare(tc6393xb->clk);
return ret;
}
int ret;
int i;
- clk_enable(tc6393xb->clk);
+ clk_prepare_enable(tc6393xb->clk);
ret = tcpd->resume(dev);
if (ret)
static const struct regmap_irq tps65090_irqs[] = {
/* INT1 IRQs*/
[TPS65090_IRQ_VAC_STATUS_CHANGE] = {
- .mask = TPS65090_INT1_MASK_VAC_STATUS_CHANGE,
+ .mask = TPS65090_INT1_MASK_VAC_STATUS_CHANGE,
},
[TPS65090_IRQ_VSYS_STATUS_CHANGE] = {
- .mask = TPS65090_INT1_MASK_VSYS_STATUS_CHANGE,
+ .mask = TPS65090_INT1_MASK_VSYS_STATUS_CHANGE,
},
[TPS65090_IRQ_BAT_STATUS_CHANGE] = {
- .mask = TPS65090_INT1_MASK_BAT_STATUS_CHANGE,
+ .mask = TPS65090_INT1_MASK_BAT_STATUS_CHANGE,
},
[TPS65090_IRQ_CHARGING_STATUS_CHANGE] = {
- .mask = TPS65090_INT1_MASK_CHARGING_STATUS_CHANGE,
+ .mask = TPS65090_INT1_MASK_CHARGING_STATUS_CHANGE,
},
[TPS65090_IRQ_CHARGING_COMPLETE] = {
- .mask = TPS65090_INT1_MASK_CHARGING_COMPLETE,
+ .mask = TPS65090_INT1_MASK_CHARGING_COMPLETE,
},
[TPS65090_IRQ_OVERLOAD_DCDC1] = {
- .mask = TPS65090_INT1_MASK_OVERLOAD_DCDC1,
+ .mask = TPS65090_INT1_MASK_OVERLOAD_DCDC1,
},
[TPS65090_IRQ_OVERLOAD_DCDC2] = {
- .mask = TPS65090_INT1_MASK_OVERLOAD_DCDC2,
+ .mask = TPS65090_INT1_MASK_OVERLOAD_DCDC2,
},
/* INT2 IRQs*/
[TPS65090_IRQ_OVERLOAD_DCDC3] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_DCDC3,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_DCDC3,
},
[TPS65090_IRQ_OVERLOAD_FET1] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET1,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET1,
},
[TPS65090_IRQ_OVERLOAD_FET2] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET2,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET2,
},
[TPS65090_IRQ_OVERLOAD_FET3] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET3,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET3,
},
[TPS65090_IRQ_OVERLOAD_FET4] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET4,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET4,
},
[TPS65090_IRQ_OVERLOAD_FET5] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET5,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET5,
},
[TPS65090_IRQ_OVERLOAD_FET6] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET6,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET6,
},
[TPS65090_IRQ_OVERLOAD_FET7] = {
- .reg_offset = 1,
- .mask = TPS65090_INT2_MASK_OVERLOAD_FET7,
+ .reg_offset = 1,
+ .mask = TPS65090_INT2_MASK_OVERLOAD_FET7,
},
};
#endif
static int tps65090_i2c_probe(struct i2c_client *client,
- const struct i2c_device_id *id)
+ const struct i2c_device_id *id)
{
struct tps65090_platform_data *pdata = dev_get_platdata(&client->dev);
int irq_base = 0;
if (client->irq) {
ret = regmap_add_irq_chip(tps65090->rmap, client->irq,
- IRQF_ONESHOT | IRQF_TRIGGER_LOW, irq_base,
- &tps65090_irq_chip, &tps65090->irq_data);
- if (ret) {
- dev_err(&client->dev,
- "IRQ init failed with err: %d\n", ret);
+ IRQF_ONESHOT | IRQF_TRIGGER_LOW, irq_base,
+ &tps65090_irq_chip, &tps65090->irq_data);
+ if (ret) {
+ dev_err(&client->dev,
+ "IRQ init failed with err: %d\n", ret);
return ret;
}
} else {
}
ret = mfd_add_devices(tps65090->dev, -1, tps65090s,
- ARRAY_SIZE(tps65090s), NULL,
- 0, regmap_irq_get_domain(tps65090->irq_data));
+ ARRAY_SIZE(tps65090s), NULL,
+ 0, regmap_irq_get_domain(tps65090->irq_data));
if (ret) {
dev_err(&client->dev, "add mfd devices failed with err: %d\n",
ret);
static const struct mfd_cell tps65217s[] = {
{
.name = "tps65217-pmic",
+ .of_compatible = "ti,tps65217-pmic",
},
{
.name = "tps65217-bl",
+ .of_compatible = "ti,tps65217-bl",
},
};
};
static struct of_device_id twl4030_power_of_match[] = {
+ {
+ .compatible = "ti,twl4030-power",
+ },
{
.compatible = "ti,twl4030-power-reset",
.data = &omap3_reset,
version >> 8, version & 0xff,
vb->usb_dev->bus->busnum, vb->usb_dev->devnum);
- ret = mfd_add_devices(&interface->dev, PLATFORM_DEVID_AUTO,
- vprbrd_devs, ARRAY_SIZE(vprbrd_devs), NULL, 0,
- NULL);
+ ret = mfd_add_hotplug_devices(&interface->dev, vprbrd_devs,
+ ARRAY_SIZE(vprbrd_devs));
if (ret != 0) {
dev_err(&interface->dev, "Failed to add mfd devices to core.");
goto error;
{ 0x00000218, 0x01A6 }, /* R536 - Mic Bias Ctrl 1 */
{ 0x00000219, 0x01A6 }, /* R537 - Mic Bias Ctrl 2 */
{ 0x0000021A, 0x01A6 }, /* R538 - Mic Bias Ctrl 3 */
- { 0x00000225, 0x0400 }, /* R549 - HP Ctrl 1L */
- { 0x00000226, 0x0400 }, /* R550 - HP Ctrl 1R */
{ 0x00000293, 0x0000 }, /* R659 - Accessory Detect Mode 1 */
{ 0x0000029B, 0x0020 }, /* R667 - Headphone Detect 1 */
{ 0x0000029C, 0x0000 }, /* R668 - Headphone Detect 2 */
case ARIZONA_MIC_BIAS_CTRL_1:
case ARIZONA_MIC_BIAS_CTRL_2:
case ARIZONA_MIC_BIAS_CTRL_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_ACCESSORY_DETECT_MODE_1:
case ARIZONA_HEADPHONE_DETECT_1:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_DSP1_SCRATCH_1:
case ARIZONA_DSP1_SCRATCH_2:
case ARIZONA_DSP1_SCRATCH_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_HP_DACVAL:
case ARIZONA_MIC_DETECT_3:
{ 0x00000548, 0x1818 }, /* R1352 - AIF2 Frame Ctrl 2 */
{ 0x00000549, 0x0000 }, /* R1353 - AIF2 Frame Ctrl 3 */
{ 0x0000054A, 0x0001 }, /* R1354 - AIF2 Frame Ctrl 4 */
+ { 0x0000054B, 0x0002 }, /* R1355 - AIF2 Frame Ctrl 5 */
+ { 0x0000054C, 0x0003 }, /* R1356 - AIF2 Frame Ctrl 6 */
+ { 0x0000054D, 0x0004 }, /* R1357 - AIF2 Frame Ctrl 7 */
+ { 0x0000054E, 0x0005 }, /* R1358 - AIF2 Frame Ctrl 8 */
{ 0x00000551, 0x0000 }, /* R1361 - AIF2 Frame Ctrl 11 */
{ 0x00000552, 0x0001 }, /* R1362 - AIF2 Frame Ctrl 12 */
+ { 0x00000553, 0x0002 }, /* R1363 - AIF2 Frame Ctrl 13 */
+ { 0x00000554, 0x0003 }, /* R1364 - AIF2 Frame Ctrl 14 */
+ { 0x00000555, 0x0004 }, /* R1365 - AIF2 Frame Ctrl 15 */
+ { 0x00000556, 0x0005 }, /* R1366 - AIF2 Frame Ctrl 16 */
{ 0x00000559, 0x0000 }, /* R1369 - AIF2 Tx Enables */
{ 0x0000055A, 0x0000 }, /* R1370 - AIF2 Rx Enables */
{ 0x00000580, 0x000C }, /* R1408 - AIF3 BCLK Ctrl */
case ARIZONA_MIC_BIAS_CTRL_1:
case ARIZONA_MIC_BIAS_CTRL_2:
case ARIZONA_MIC_BIAS_CTRL_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_ACCESSORY_DETECT_MODE_1:
case ARIZONA_HEADPHONE_DETECT_1:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_AIF2_FRAME_CTRL_2:
case ARIZONA_AIF2_FRAME_CTRL_3:
case ARIZONA_AIF2_FRAME_CTRL_4:
+ case ARIZONA_AIF2_FRAME_CTRL_5:
+ case ARIZONA_AIF2_FRAME_CTRL_6:
+ case ARIZONA_AIF2_FRAME_CTRL_7:
+ case ARIZONA_AIF2_FRAME_CTRL_8:
case ARIZONA_AIF2_FRAME_CTRL_11:
case ARIZONA_AIF2_FRAME_CTRL_12:
+ case ARIZONA_AIF2_FRAME_CTRL_13:
+ case ARIZONA_AIF2_FRAME_CTRL_14:
+ case ARIZONA_AIF2_FRAME_CTRL_15:
+ case ARIZONA_AIF2_FRAME_CTRL_16:
case ARIZONA_AIF2_TX_ENABLES:
case ARIZONA_AIF2_RX_ENABLES:
case ARIZONA_AIF3_BCLK_CTRL:
case ARIZONA_ASYNC_SAMPLE_RATE_1_STATUS:
case ARIZONA_ASYNC_SAMPLE_RATE_2_STATUS:
case ARIZONA_MIC_DETECT_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_INPUT_ENABLES_STATUS:
case ARIZONA_OUTPUT_STATUS_1:
goto err;
}
- mode = id2 & WM8350_CONF_STS_MASK >> 10;
+ mode = (id2 & WM8350_CONF_STS_MASK) >> 10;
cust_id = id2 & WM8350_CUST_ID_MASK;
chip_rev = (id2 & WM8350_CHIP_REV_MASK) >> 12;
dev_info(wm8350->dev,
{ 0x00000C23, 0x0000 }, /* R3107 - Misc Pad Ctrl 4 */
{ 0x00000C24, 0x0000 }, /* R3108 - Misc Pad Ctrl 5 */
{ 0x00000D08, 0xFFFF }, /* R3336 - Interrupt Status 1 Mask */
+ { 0x00000D09, 0xFFFF }, /* R3337 - Interrupt Status 2 Mask */
{ 0x00000D0A, 0xFFFF }, /* R3338 - Interrupt Status 3 Mask */
{ 0x00000D0B, 0xFFFF }, /* R3339 - Interrupt Status 4 Mask */
{ 0x00000D0C, 0xFEFF }, /* R3340 - Interrupt Status 5 Mask */
case ARIZONA_MIC_BIAS_CTRL_1:
case ARIZONA_MIC_BIAS_CTRL_2:
case ARIZONA_MIC_BIAS_CTRL_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_ACCESSORY_DETECT_MODE_1:
case ARIZONA_HEADPHONE_DETECT_1:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_INTERRUPT_STATUS_4:
case ARIZONA_INTERRUPT_STATUS_5:
case ARIZONA_INTERRUPT_STATUS_1_MASK:
+ case ARIZONA_INTERRUPT_STATUS_2_MASK:
case ARIZONA_INTERRUPT_STATUS_3_MASK:
case ARIZONA_INTERRUPT_STATUS_4_MASK:
case ARIZONA_INTERRUPT_STATUS_5_MASK:
case ARIZONA_SAMPLE_RATE_3_STATUS:
case ARIZONA_ASYNC_SAMPLE_RATE_1_STATUS:
case ARIZONA_MIC_DETECT_3:
+ case ARIZONA_HP_CTRL_1L:
+ case ARIZONA_HP_CTRL_1R:
case ARIZONA_HEADPHONE_DETECT_2:
case ARIZONA_INPUT_ENABLES_STATUS:
case ARIZONA_OUTPUT_STATUS_1:
/*
* We've only got one major, so number of mmcblk devices is
- * limited to 256 / number of minors per device.
+ * limited to (1 << 20) / number of minors per device. It is also
+ * currently limited by the size of the static bitmaps below.
*/
static int max_devices;
-/* 256 minors, so at most 256 separate devices */
-static DECLARE_BITMAP(dev_use, 256);
-static DECLARE_BITMAP(name_use, 256);
+#define MAX_DEVICES 256
+
+/* TODO: Replace these with struct ida */
+static DECLARE_BITMAP(dev_use, MAX_DEVICES);
+static DECLARE_BITMAP(name_use, MAX_DEVICES);
/*
* There is one mmc_blk_data per slot.
/*
* Only set in main mmc_blk_data associated
- * with mmc_card with mmc_set_drvdata, and keeps
+ * with mmc_card with dev_set_drvdata, and keeps
* track of the current selected device partition.
*/
unsigned int part_curr;
int ret;
struct mmc_blk_data *md = mmc_blk_get(dev_to_disk(dev));
- ret = snprintf(buf, PAGE_SIZE, "%d",
+ ret = snprintf(buf, PAGE_SIZE, "%d\n",
get_disk_ro(dev_to_disk(dev)) ^
md->read_only);
mmc_blk_put(md);
struct mmc_blk_data *md)
{
int ret;
- struct mmc_blk_data *main_md = mmc_get_drvdata(card);
+ struct mmc_blk_data *main_md = dev_get_drvdata(&card->dev);
if (main_md->part_curr == md->part_type)
return 0;
err = mmc_hw_reset(host);
/* Ensure we switch back to the correct partition */
if (err != -EOPNOTSUPP) {
- struct mmc_blk_data *main_md = mmc_get_drvdata(host->card);
+ struct mmc_blk_data *main_md =
+ dev_get_drvdata(&host->card->dev);
int part_err;
main_md->part_curr = main_md->part_type;
}
if (status & R1_EXCEPTION_EVENT) {
- ext_csd = kzalloc(512, GFP_KERNEL);
- if (!ext_csd) {
- pr_err("%s: unable to allocate buffer for ext_csd\n",
- req->rq_disk->disk_name);
- return -ENOMEM;
- }
-
- err = mmc_send_ext_csd(card, ext_csd);
+ err = mmc_get_ext_csd(card, &ext_csd);
if (err) {
pr_err("%s: error %d sending ext_csd\n",
req->rq_disk->disk_name, err);
- check = MMC_BLK_ABORT;
- goto free;
+ return MMC_BLK_ABORT;
}
if ((ext_csd[EXT_CSD_EXP_EVENTS_STATUS] &
req->rq_disk->disk_name, packed->nr_entries,
packed->blocks, packed->idx_failure);
}
-free:
kfree(ext_csd);
}
/*
* !subname implies we are creating main mmc_blk_data that will be
- * associated with mmc_card with mmc_set_drvdata. Due to device
+ * associated with mmc_card with dev_set_drvdata. Due to device
* partitions, devidx will not coincide with a per-physical card
* index anymore so we keep track of a name index.
*/
END_FIXUP
};
-static int mmc_blk_probe(struct mmc_card *card)
+static int mmc_blk_probe(struct device *dev)
{
+ struct mmc_card *card = mmc_dev_to_card(dev);
struct mmc_blk_data *md, *part_md;
char cap_str[10];
if (mmc_blk_alloc_parts(card, md))
goto out;
- mmc_set_drvdata(card, md);
+ dev_set_drvdata(dev, md);
if (mmc_add_disk(md))
goto out;
return 0;
}
-static void mmc_blk_remove(struct mmc_card *card)
+static int mmc_blk_remove(struct device *dev)
{
- struct mmc_blk_data *md = mmc_get_drvdata(card);
+ struct mmc_card *card = mmc_dev_to_card(dev);
+ struct mmc_blk_data *md = dev_get_drvdata(dev);
mmc_blk_remove_parts(card, md);
pm_runtime_get_sync(&card->dev);
pm_runtime_disable(&card->dev);
pm_runtime_put_noidle(&card->dev);
mmc_blk_remove_req(md);
- mmc_set_drvdata(card, NULL);
+ dev_set_drvdata(dev, NULL);
+
+ return 0;
}
-static int _mmc_blk_suspend(struct mmc_card *card)
+static int _mmc_blk_suspend(struct device *dev)
{
struct mmc_blk_data *part_md;
- struct mmc_blk_data *md = mmc_get_drvdata(card);
+ struct mmc_blk_data *md = dev_get_drvdata(dev);
if (md) {
mmc_queue_suspend(&md->queue);
return 0;
}
-static void mmc_blk_shutdown(struct mmc_card *card)
+static void mmc_blk_shutdown(struct device *dev)
{
- _mmc_blk_suspend(card);
+ _mmc_blk_suspend(dev);
}
-#ifdef CONFIG_PM
-static int mmc_blk_suspend(struct mmc_card *card)
+#ifdef CONFIG_PM_SLEEP
+static int mmc_blk_suspend(struct device *dev)
{
- return _mmc_blk_suspend(card);
+ return _mmc_blk_suspend(dev);
}
-static int mmc_blk_resume(struct mmc_card *card)
+static int mmc_blk_resume(struct device *dev)
{
struct mmc_blk_data *part_md;
- struct mmc_blk_data *md = mmc_get_drvdata(card);
+ struct mmc_blk_data *md = dev_get_drvdata(dev);
if (md) {
/*
}
return 0;
}
-#else
-#define mmc_blk_suspend NULL
-#define mmc_blk_resume NULL
#endif
-static struct mmc_driver mmc_driver = {
- .drv = {
- .name = "mmcblk",
- },
+static SIMPLE_DEV_PM_OPS(mmc_blk_pm_ops, mmc_blk_suspend, mmc_blk_resume);
+
+static struct device_driver mmc_driver = {
+ .name = "mmcblk",
+ .pm = &mmc_blk_pm_ops,
.probe = mmc_blk_probe,
.remove = mmc_blk_remove,
- .suspend = mmc_blk_suspend,
- .resume = mmc_blk_resume,
.shutdown = mmc_blk_shutdown,
};
if (perdev_minors != CONFIG_MMC_BLOCK_MINORS)
pr_info("mmcblk: using %d minors per device\n", perdev_minors);
- max_devices = 256 / perdev_minors;
+ max_devices = min(MAX_DEVICES, (1 << MINORBITS) / perdev_minors);
res = register_blkdev(MMC_BLOCK_MAJOR, "mmc");
if (res)
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include <linux/slab.h>
+#include <linux/device.h>
#include <linux/scatterlist.h>
#include <linux/swap.h> /* For nr_free_buffer_pages() */
#define BUFFER_ORDER 2
#define BUFFER_SIZE (PAGE_SIZE << BUFFER_ORDER)
+#define TEST_ALIGN_END 8
+
/*
* Limit the test area size to the maximum MMC HC erase group size. Note that
* the maximum SD allocation unit size is just 4MiB.
int ret, i;
struct scatterlist sg;
- for (i = 1;i < 4;i++) {
+ for (i = 1; i < TEST_ALIGN_END; i++) {
sg_init_one(&sg, test->buffer + i, 512);
ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 1);
if (ret)
int ret, i;
struct scatterlist sg;
- for (i = 1;i < 4;i++) {
+ for (i = 1; i < TEST_ALIGN_END; i++) {
sg_init_one(&sg, test->buffer + i, 512);
ret = mmc_test_transfer(test, &sg, 1, 0, 1, 512, 0);
if (ret)
if (size < 1024)
return RESULT_UNSUP_HOST;
- for (i = 1;i < 4;i++) {
+ for (i = 1; i < TEST_ALIGN_END; i++) {
sg_init_one(&sg, test->buffer + i, size);
ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 1);
if (ret)
if (size < 1024)
return RESULT_UNSUP_HOST;
- for (i = 1;i < 4;i++) {
+ for (i = 1; i < TEST_ALIGN_END; i++) {
sg_init_one(&sg, test->buffer + i, size);
ret = mmc_test_transfer(test, &sg, 1, 0, size/512, 512, 0);
if (ret)
return ret;
}
-static int mmc_test_probe(struct mmc_card *card)
+static int mmc_test_probe(struct device *dev)
{
+ struct mmc_card *card = mmc_dev_to_card(dev);
int ret;
if (!mmc_card_mmc(card) && !mmc_card_sd(card))
return 0;
}
-static void mmc_test_remove(struct mmc_card *card)
+static int mmc_test_remove(struct device *dev)
{
+ struct mmc_card *card = mmc_dev_to_card(dev);
+
mmc_test_free_result(card);
mmc_test_free_dbgfs_file(card);
+
+ return 0;
}
-static void mmc_test_shutdown(struct mmc_card *card)
+static void mmc_test_shutdown(struct device *dev)
{
}
-static struct mmc_driver mmc_driver = {
- .drv = {
- .name = "mmc_test",
- },
+static struct device_driver mmc_driver = {
+ .name = "mmc_test",
.probe = mmc_test_probe,
.remove = mmc_test_remove,
.shutdown = mmc_test_shutdown,
if (!mqrq_cur->bounce_buf) {
pr_warn("%s: unable to allocate bounce cur buffer\n",
mmc_card_name(card));
- }
- mqrq_prev->bounce_buf = kmalloc(bouncesz, GFP_KERNEL);
- if (!mqrq_prev->bounce_buf) {
- pr_warn("%s: unable to allocate bounce prev buffer\n",
- mmc_card_name(card));
- kfree(mqrq_cur->bounce_buf);
- mqrq_cur->bounce_buf = NULL;
+ } else {
+ mqrq_prev->bounce_buf =
+ kmalloc(bouncesz, GFP_KERNEL);
+ if (!mqrq_prev->bounce_buf) {
+ pr_warn("%s: unable to allocate bounce prev buffer\n",
+ mmc_card_name(card));
+ kfree(mqrq_cur->bounce_buf);
+ mqrq_cur->bounce_buf = NULL;
+ }
}
}
#include "sdio_cis.h"
#include "bus.h"
-#define to_mmc_driver(d) container_of(d, struct mmc_driver, drv)
-
static ssize_t type_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
return retval;
}
-static int mmc_bus_probe(struct device *dev)
-{
- struct mmc_driver *drv = to_mmc_driver(dev->driver);
- struct mmc_card *card = mmc_dev_to_card(dev);
-
- return drv->probe(card);
-}
-
-static int mmc_bus_remove(struct device *dev)
-{
- struct mmc_driver *drv = to_mmc_driver(dev->driver);
- struct mmc_card *card = mmc_dev_to_card(dev);
-
- drv->remove(card);
-
- return 0;
-}
-
static void mmc_bus_shutdown(struct device *dev)
{
- struct mmc_driver *drv = to_mmc_driver(dev->driver);
struct mmc_card *card = mmc_dev_to_card(dev);
struct mmc_host *host = card->host;
int ret;
- if (dev->driver && drv->shutdown)
- drv->shutdown(card);
+ if (dev->driver && dev->driver->shutdown)
+ dev->driver->shutdown(dev);
if (host->bus_ops->shutdown) {
ret = host->bus_ops->shutdown(host);
#ifdef CONFIG_PM_SLEEP
static int mmc_bus_suspend(struct device *dev)
{
- struct mmc_driver *drv = to_mmc_driver(dev->driver);
struct mmc_card *card = mmc_dev_to_card(dev);
struct mmc_host *host = card->host;
int ret;
- if (dev->driver && drv->suspend) {
- ret = drv->suspend(card);
- if (ret)
- return ret;
- }
+ ret = pm_generic_suspend(dev);
+ if (ret)
+ return ret;
ret = host->bus_ops->suspend(host);
return ret;
static int mmc_bus_resume(struct device *dev)
{
- struct mmc_driver *drv = to_mmc_driver(dev->driver);
struct mmc_card *card = mmc_dev_to_card(dev);
struct mmc_host *host = card->host;
int ret;
pr_warn("%s: error %d during resume (card was removed?)\n",
mmc_hostname(host), ret);
- if (dev->driver && drv->resume)
- ret = drv->resume(card);
-
+ ret = pm_generic_resume(dev);
return ret;
}
#endif
.dev_groups = mmc_dev_groups,
.match = mmc_bus_match,
.uevent = mmc_bus_uevent,
- .probe = mmc_bus_probe,
- .remove = mmc_bus_remove,
.shutdown = mmc_bus_shutdown,
.pm = &mmc_bus_pm_ops,
};
* mmc_register_driver - register a media driver
* @drv: MMC media driver
*/
-int mmc_register_driver(struct mmc_driver *drv)
+int mmc_register_driver(struct device_driver *drv)
{
- drv->drv.bus = &mmc_bus_type;
- return driver_register(&drv->drv);
+ drv->bus = &mmc_bus_type;
+ return driver_register(drv);
}
-
EXPORT_SYMBOL(mmc_register_driver);
/**
* mmc_unregister_driver - unregister a media driver
* @drv: MMC media driver
*/
-void mmc_unregister_driver(struct mmc_driver *drv)
+void mmc_unregister_driver(struct device_driver *drv)
{
- drv->drv.bus = &mmc_bus_type;
- driver_unregister(&drv->drv);
+ drv->bus = &mmc_bus_type;
+ driver_unregister(drv);
}
-
EXPORT_SYMBOL(mmc_unregister_driver);
static void mmc_release_card(struct device *dev)
led_trigger_event(host->led, LED_OFF);
+ if (mrq->sbc) {
+ pr_debug("%s: req done <CMD%u>: %d: %08x %08x %08x %08x\n",
+ mmc_hostname(host), mrq->sbc->opcode,
+ mrq->sbc->error,
+ mrq->sbc->resp[0], mrq->sbc->resp[1],
+ mrq->sbc->resp[2], mrq->sbc->resp[3]);
+ }
+
pr_debug("%s: req done (CMD%u): %d: %08x %08x %08x %08x\n",
mmc_hostname(host), cmd->opcode, err,
cmd->resp[0], cmd->resp[1],
mrq->cmd->error = 0;
mrq->cmd->mrq = mrq;
+ if (mrq->sbc) {
+ mrq->sbc->error = 0;
+ mrq->sbc->mrq = mrq;
+ }
if (mrq->data) {
BUG_ON(mrq->data->blksz > host->max_blk_size);
BUG_ON(mrq->data->blocks > host->max_blk_count);
if (host->card && mmc_card_mmc(host->card) &&
((mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1) ||
(mmc_resp_type(host->areq->mrq->cmd) == MMC_RSP_R1B)) &&
- (host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT))
+ (host->areq->mrq->cmd->resp[0] & R1_EXCEPTION_EVENT)) {
+
+ /* Cancel the prepared request */
+ if (areq)
+ mmc_post_req(host, areq->mrq, -EINVAL);
+
mmc_start_bkops(host->card, true);
+
+ /* prepare the request again */
+ if (areq)
+ mmc_pre_req(host, areq->mrq, !host->areq);
+ }
}
if (!err && areq)
int err;
u8 *ext_csd;
- /*
- * In future work, we should consider storing the entire ext_csd.
- */
- ext_csd = kmalloc(512, GFP_KERNEL);
- if (!ext_csd) {
- pr_err("%s: could not allocate buffer to receive the ext_csd.\n",
- mmc_hostname(card->host));
- return -ENOMEM;
- }
-
mmc_claim_host(card->host);
- err = mmc_send_ext_csd(card, ext_csd);
+ err = mmc_get_ext_csd(card, &ext_csd);
mmc_release_host(card->host);
if (err)
- goto out;
+ return err;
card->ext_csd.raw_bkops_status = ext_csd[EXT_CSD_BKOPS_STATUS];
card->ext_csd.raw_exception_status = ext_csd[EXT_CSD_EXP_EVENTS_STATUS];
-out:
kfree(ext_csd);
- return err;
+ return 0;
}
EXPORT_SYMBOL(mmc_read_bkops_status);
mmc_host_clk_release(host);
}
+/*
+ * Set initial state after a power cycle or a hw_reset.
+ */
+void mmc_set_initial_state(struct mmc_host *host)
+{
+ if (mmc_host_is_spi(host))
+ host->ios.chip_select = MMC_CS_HIGH;
+ else
+ host->ios.chip_select = MMC_CS_DONTCARE;
+ host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
+ host->ios.bus_width = MMC_BUS_WIDTH_1;
+ host->ios.timing = MMC_TIMING_LEGACY;
+
+ mmc_set_ios(host);
+}
+
/**
* mmc_vdd_to_ocrbitnum - Convert a voltage to the OCR bit number
* @vdd: voltage (mV)
pr_warn("%s: cannot verify signal voltage switch\n",
mmc_hostname(host));
+ mmc_host_clk_hold(host);
+
cmd.opcode = SD_SWITCH_VOLTAGE;
cmd.arg = 0;
cmd.flags = MMC_RSP_R1 | MMC_CMD_AC;
err = mmc_wait_for_cmd(host, &cmd, 0);
if (err)
- return err;
+ goto err_command;
- if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR))
- return -EIO;
-
- mmc_host_clk_hold(host);
+ if (!mmc_host_is_spi(host) && (cmd.resp[0] & R1_ERROR)) {
+ err = -EIO;
+ goto err_command;
+ }
/*
* The card should drive cmd and dat[0:3] low immediately
* after the response of cmd11, but wait 1 ms to be sure
mmc_power_cycle(host, ocr);
}
+err_command:
mmc_host_clk_release(host);
return err;
mmc_host_clk_hold(host);
host->ios.vdd = fls(ocr) - 1;
- if (mmc_host_is_spi(host))
- host->ios.chip_select = MMC_CS_HIGH;
- else
- host->ios.chip_select = MMC_CS_DONTCARE;
- host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
host->ios.power_mode = MMC_POWER_UP;
- host->ios.bus_width = MMC_BUS_WIDTH_1;
- host->ios.timing = MMC_TIMING_LEGACY;
- mmc_set_ios(host);
+ /* Set initial state and call mmc_set_ios */
+ mmc_set_initial_state(host);
/* Try to set signal voltage to 3.3V but fall back to 1.8v or 1.2v */
if (__mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330) == 0)
host->ios.clock = 0;
host->ios.vdd = 0;
- if (!mmc_host_is_spi(host)) {
- host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
- host->ios.chip_select = MMC_CS_DONTCARE;
- }
host->ios.power_mode = MMC_POWER_OFF;
- host->ios.bus_width = MMC_BUS_WIDTH_1;
- host->ios.timing = MMC_TIMING_LEGACY;
- mmc_set_ios(host);
+ /* Set initial state and call mmc_set_ios */
+ mmc_set_initial_state(host);
/*
* Some configurations, such as the 802.11 SDIO card in the OLPC
/* If the reset has happened, then a status command will fail */
if (check) {
- struct mmc_command cmd = {0};
- int err;
+ u32 status;
- cmd.opcode = MMC_SEND_STATUS;
- if (!mmc_host_is_spi(card->host))
- cmd.arg = card->rca << 16;
- cmd.flags = MMC_RSP_SPI_R2 | MMC_RSP_R1 | MMC_CMD_AC;
- err = mmc_wait_for_cmd(card->host, &cmd, 0);
- if (!err) {
+ if (!mmc_send_status(card, &status)) {
mmc_host_clk_release(host);
return -ENOSYS;
}
}
- if (mmc_host_is_spi(host)) {
- host->ios.chip_select = MMC_CS_HIGH;
- host->ios.bus_mode = MMC_BUSMODE_PUSHPULL;
- } else {
- host->ios.chip_select = MMC_CS_DONTCARE;
- host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
- }
- host->ios.bus_width = MMC_BUS_WIDTH_1;
- host->ios.timing = MMC_TIMING_LEGACY;
- mmc_set_ios(host);
+ /* Set initial state and call mmc_set_ios */
+ mmc_set_initial_state(host);
mmc_host_clk_release(host);
void mmc_power_up(struct mmc_host *host, u32 ocr);
void mmc_power_off(struct mmc_host *host);
void mmc_power_cycle(struct mmc_host *host, u32 ocr);
+void mmc_set_initial_state(struct mmc_host *host);
static inline void mmc_delay(unsigned int ms)
{
if (!buf)
return -ENOMEM;
- ext_csd = kmalloc(512, GFP_KERNEL);
- if (!ext_csd) {
- err = -ENOMEM;
- goto out_free;
- }
-
mmc_get_card(card);
- err = mmc_send_ext_csd(card, ext_csd);
+ err = mmc_get_ext_csd(card, &ext_csd);
mmc_put_card(card);
if (err)
goto out_free;
out_free:
kfree(buf);
- kfree(ext_csd);
return err;
}
return 0;
}
-/*
- * Read extended CSD.
- */
-static int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
-{
- int err;
- u8 *ext_csd;
-
- BUG_ON(!card);
- BUG_ON(!new_ext_csd);
-
- *new_ext_csd = NULL;
-
- if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
- return 0;
-
- /*
- * As the ext_csd is so large and mostly unused, we don't store the
- * raw block in mmc_card.
- */
- ext_csd = kmalloc(512, GFP_KERNEL);
- if (!ext_csd) {
- pr_err("%s: could not allocate a buffer to "
- "receive the ext_csd.\n", mmc_hostname(card->host));
- return -ENOMEM;
- }
-
- err = mmc_send_ext_csd(card, ext_csd);
- if (err) {
- kfree(ext_csd);
- *new_ext_csd = NULL;
-
- /* If the host or the card can't do the switch,
- * fail more gracefully. */
- if ((err != -EINVAL)
- && (err != -ENOSYS)
- && (err != -EFAULT))
- return err;
-
- /*
- * High capacity cards should have this "magic" size
- * stored in their CSD.
- */
- if (card->csd.capacity == (4096 * 512)) {
- pr_err("%s: unable to read EXT_CSD "
- "on a possible high capacity card. "
- "Card will be ignored.\n",
- mmc_hostname(card->host));
- } else {
- pr_warn("%s: unable to read EXT_CSD, performance might suffer\n",
- mmc_hostname(card->host));
- err = 0;
- }
- } else
- *new_ext_csd = ext_csd;
-
- return err;
-}
-
static void mmc_select_card_type(struct mmc_card *card)
{
struct mmc_host *host = card->host;
/*
* Decode extended CSD.
*/
-static int mmc_read_ext_csd(struct mmc_card *card, u8 *ext_csd)
+static int mmc_decode_ext_csd(struct mmc_card *card, u8 *ext_csd)
{
int err = 0, idx;
unsigned int part_size;
- BUG_ON(!card);
-
- if (!ext_csd)
- return 0;
-
/* Version is coded in the CSD_STRUCTURE byte in the EXT_CSD register */
card->ext_csd.raw_ext_csd_structure = ext_csd[EXT_CSD_STRUCTURE];
if (card->csd.structure == 3) {
card->ext_csd.data_sector_size = 512;
}
+ /* eMMC v5 or later */
+ if (card->ext_csd.rev >= 7) {
+ memcpy(card->ext_csd.fwrev, &ext_csd[EXT_CSD_FIRMWARE_VERSION],
+ MMC_FIRMWARE_LEN);
+ card->ext_csd.ffu_capable =
+ (ext_csd[EXT_CSD_SUPPORTED_MODE] & 0x1) &&
+ !(ext_csd[EXT_CSD_FW_CONFIG] & 0x1);
+ }
out:
return err;
}
-static inline void mmc_free_ext_csd(u8 *ext_csd)
+static int mmc_read_ext_csd(struct mmc_card *card)
{
+ u8 *ext_csd;
+ int err;
+
+ if (!mmc_can_ext_csd(card))
+ return 0;
+
+ err = mmc_get_ext_csd(card, &ext_csd);
+ if (err) {
+ /* If the host or the card can't do the switch,
+ * fail more gracefully. */
+ if ((err != -EINVAL)
+ && (err != -ENOSYS)
+ && (err != -EFAULT))
+ return err;
+
+ /*
+ * High capacity cards should have this "magic" size
+ * stored in their CSD.
+ */
+ if (card->csd.capacity == (4096 * 512)) {
+ pr_err("%s: unable to read EXT_CSD on a possible high capacity card. Card will be ignored.\n",
+ mmc_hostname(card->host));
+ } else {
+ pr_warn("%s: unable to read EXT_CSD, performance might suffer\n",
+ mmc_hostname(card->host));
+ err = 0;
+ }
+
+ return err;
+ }
+
+ err = mmc_decode_ext_csd(card, ext_csd);
kfree(ext_csd);
+ return err;
}
-
static int mmc_compare_ext_csds(struct mmc_card *card, unsigned bus_width)
{
u8 *bw_ext_csd;
return 0;
err = mmc_get_ext_csd(card, &bw_ext_csd);
-
- if (err || bw_ext_csd == NULL) {
- err = -EINVAL;
- goto out;
- }
+ if (err)
+ return err;
/* only compare read only fields */
err = !((card->ext_csd.raw_partition_support ==
if (err)
err = -EINVAL;
-out:
- mmc_free_ext_csd(bw_ext_csd);
+ kfree(bw_ext_csd);
return err;
}
MMC_DEV_ATTR(date, "%02d/%04d\n", card->cid.month, card->cid.year);
MMC_DEV_ATTR(erase_size, "%u\n", card->erase_size << 9);
MMC_DEV_ATTR(preferred_erase_size, "%u\n", card->pref_erase << 9);
-MMC_DEV_ATTR(fwrev, "0x%x\n", card->cid.fwrev);
+MMC_DEV_ATTR(ffu_capable, "%d\n", card->ext_csd.ffu_capable);
MMC_DEV_ATTR(hwrev, "0x%x\n", card->cid.hwrev);
MMC_DEV_ATTR(manfid, "0x%06x\n", card->cid.manfid);
MMC_DEV_ATTR(name, "%s\n", card->cid.prod_name);
MMC_DEV_ATTR(raw_rpmb_size_mult, "%#x\n", card->ext_csd.raw_rpmb_size_mult);
MMC_DEV_ATTR(rel_sectors, "%#x\n", card->ext_csd.rel_sectors);
+static ssize_t mmc_fwrev_show(struct device *dev,
+ struct device_attribute *attr,
+ char *buf)
+{
+ struct mmc_card *card = mmc_dev_to_card(dev);
+
+ if (card->ext_csd.rev < 7) {
+ return sprintf(buf, "0x%x\n", card->cid.fwrev);
+ } else {
+ return sprintf(buf, "0x%*phN\n", MMC_FIRMWARE_LEN,
+ card->ext_csd.fwrev);
+ }
+}
+
+static DEVICE_ATTR(fwrev, S_IRUGO, mmc_fwrev_show, NULL);
+
static struct attribute *mmc_std_attrs[] = {
&dev_attr_cid.attr,
&dev_attr_csd.attr,
&dev_attr_erase_size.attr,
&dev_attr_preferred_erase_size.attr,
&dev_attr_fwrev.attr,
+ &dev_attr_ffu_capable.attr,
&dev_attr_hwrev.attr,
&dev_attr_manfid.attr,
&dev_attr_name.attr,
unsigned int pwrclass_val = 0;
int err = 0;
- /* Power class selection is supported for versions >= 4.0 */
- if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
- return 0;
-
- /* Power class values are defined only for 4/8 bit bus */
- if (bus_width == EXT_CSD_BUS_WIDTH_1)
- return 0;
-
switch (1 << host->ios.vdd) {
case MMC_VDD_165_195:
if (host->ios.clock <= MMC_HIGH_26_MAX_DTR)
int err, ddr;
/* Power class selection is supported for versions >= 4.0 */
- if (card->csd.mmca_vsn < CSD_SPEC_VER_4)
+ if (!mmc_can_ext_csd(card))
return 0;
bus_width = host->ios.bus_width;
unsigned idx, bus_width = 0;
int err = 0;
- if ((card->csd.mmca_vsn < CSD_SPEC_VER_4) &&
+ if (!mmc_can_ext_csd(card) &&
!(host->caps & (MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA)))
return 0;
ext_csd_bits,
card->ext_csd.generic_cmd6_time);
if (err) {
- pr_warn("%s: switch to bus width %d ddr failed\n",
+ pr_err("%s: switch to bus width %d ddr failed\n",
mmc_hostname(host), 1 << bus_width);
return err;
}
card->ext_csd.generic_cmd6_time,
true, true, true);
if (err) {
- pr_warn("%s: switch to high-speed from hs200 failed, err:%d\n",
+ pr_err("%s: switch to high-speed from hs200 failed, err:%d\n",
mmc_hostname(host), err);
return err;
}
EXT_CSD_DDR_BUS_WIDTH_8,
card->ext_csd.generic_cmd6_time);
if (err) {
- pr_warn("%s: switch to bus width for hs400 failed, err:%d\n",
+ pr_err("%s: switch to bus width for hs400 failed, err:%d\n",
mmc_hostname(host), err);
return err;
}
card->ext_csd.generic_cmd6_time,
true, true, true);
if (err) {
- pr_warn("%s: switch to hs400 failed, err:%d\n",
+ pr_err("%s: switch to hs400 failed, err:%d\n",
mmc_hostname(host), err);
return err;
}
{
int err = 0;
- if ((card->csd.mmca_vsn < CSD_SPEC_VER_4 &&
- card->ext_csd.hs_max_dtr == 0))
+ if (!mmc_can_ext_csd(card))
goto bus_speed;
if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200)
mmc_host_clk_release(host);
if (err)
- pr_warn("%s: tuning execution failed\n",
+ pr_err("%s: tuning execution failed\n",
mmc_hostname(host));
}
int err;
u32 cid[4];
u32 rocr;
- u8 *ext_csd = NULL;
BUG_ON(!host);
WARN_ON(!host->claimed);
}
if (!oldcard) {
- /*
- * Fetch and process extended CSD.
- */
-
- err = mmc_get_ext_csd(card, &ext_csd);
- if (err)
- goto free_card;
- err = mmc_read_ext_csd(card, ext_csd);
+ /* Read extended CSD. */
+ err = mmc_read_ext_csd(card);
if (err)
goto free_card;
if (mmc_card_hs200(card)) {
err = mmc_hs200_tuning(card);
if (err)
- goto err;
+ goto free_card;
err = mmc_select_hs400(card);
if (err)
- goto err;
+ goto free_card;
} else if (mmc_card_hs(card)) {
/* Select the desired bus width optionally */
err = mmc_select_bus_width(card);
if (!IS_ERR_VALUE(err)) {
err = mmc_select_hs_ddr(card);
if (err)
- goto err;
+ goto free_card;
}
}
if (!oldcard)
host->card = card;
- mmc_free_ext_csd(ext_csd);
return 0;
free_card:
if (!oldcard)
mmc_remove_card(card);
err:
- mmc_free_ext_csd(ext_csd);
-
return err;
}
struct mmc_command cmd = {0};
struct mmc_data data = {0};
struct scatterlist sg;
- void *data_buf;
- int is_on_stack;
-
- is_on_stack = object_is_on_stack(buf);
- if (is_on_stack) {
- /*
- * dma onto stack is unsafe/nonportable, but callers to this
- * routine normally provide temporary on-stack buffers ...
- */
- data_buf = kmalloc(len, GFP_KERNEL);
- if (!data_buf)
- return -ENOMEM;
- } else
- data_buf = buf;
mrq.cmd = &cmd;
mrq.data = &data;
data.sg = &sg;
data.sg_len = 1;
- sg_init_one(&sg, data_buf, len);
+ sg_init_one(&sg, buf, len);
if (opcode == MMC_SEND_CSD || opcode == MMC_SEND_CID) {
/*
mmc_wait_for_req(host, &mrq);
- if (is_on_stack) {
- memcpy(buf, data_buf, len);
- kfree(data_buf);
- }
-
if (cmd.error)
return cmd.error;
if (data.error)
return mmc_send_cxd_native(card->host, card->rca << 16,
csd, MMC_SEND_CSD);
- csd_tmp = kmalloc(16, GFP_KERNEL);
+ csd_tmp = kzalloc(16, GFP_KERNEL);
if (!csd_tmp)
return -ENOMEM;
cid, MMC_SEND_CID);
}
- cid_tmp = kmalloc(16, GFP_KERNEL);
+ cid_tmp = kzalloc(16, GFP_KERNEL);
if (!cid_tmp)
return -ENOMEM;
return ret;
}
-int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd)
+int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd)
{
- return mmc_send_cxd_data(card, card->host, MMC_SEND_EXT_CSD,
- ext_csd, 512);
+ int err;
+ u8 *ext_csd;
+
+ if (!card || !new_ext_csd)
+ return -EINVAL;
+
+ if (!mmc_can_ext_csd(card))
+ return -EOPNOTSUPP;
+
+ /*
+ * As the ext_csd is so large and mostly unused, we don't store the
+ * raw block in mmc_card.
+ */
+ ext_csd = kzalloc(512, GFP_KERNEL);
+ if (!ext_csd)
+ return -ENOMEM;
+
+ err = mmc_send_cxd_data(card, card->host, MMC_SEND_EXT_CSD, ext_csd,
+ 512);
+ if (err)
+ kfree(ext_csd);
+ else
+ *new_ext_csd = ext_csd;
+
+ return err;
}
-EXPORT_SYMBOL_GPL(mmc_send_ext_csd);
+EXPORT_SYMBOL_GPL(mmc_get_ext_csd);
int mmc_spi_read_ocr(struct mmc_host *host, int highcap, u32 *ocrp)
{
}
EXPORT_SYMBOL_GPL(mmc_switch);
+int mmc_send_tuning(struct mmc_host *host)
+{
+ struct mmc_request mrq = {NULL};
+ struct mmc_command cmd = {0};
+ struct mmc_data data = {0};
+ struct scatterlist sg;
+ struct mmc_ios *ios = &host->ios;
+ const u8 *tuning_block_pattern;
+ int size, err = 0;
+ u8 *data_buf;
+ u32 opcode;
+
+ if (ios->bus_width == MMC_BUS_WIDTH_8) {
+ tuning_block_pattern = tuning_blk_pattern_8bit;
+ size = sizeof(tuning_blk_pattern_8bit);
+ opcode = MMC_SEND_TUNING_BLOCK_HS200;
+ } else if (ios->bus_width == MMC_BUS_WIDTH_4) {
+ tuning_block_pattern = tuning_blk_pattern_4bit;
+ size = sizeof(tuning_blk_pattern_4bit);
+ opcode = MMC_SEND_TUNING_BLOCK;
+ } else
+ return -EINVAL;
+
+ data_buf = kzalloc(size, GFP_KERNEL);
+ if (!data_buf)
+ return -ENOMEM;
+
+ mrq.cmd = &cmd;
+ mrq.data = &data;
+
+ cmd.opcode = opcode;
+ cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
+
+ data.blksz = size;
+ data.blocks = 1;
+ data.flags = MMC_DATA_READ;
+
+ /*
+ * According to the tuning specs, Tuning process
+ * is normally shorter 40 executions of CMD19,
+ * and timeout value should be shorter than 150 ms
+ */
+ data.timeout_ns = 150 * NSEC_PER_MSEC;
+
+ data.sg = &sg;
+ data.sg_len = 1;
+ sg_init_one(&sg, data_buf, size);
+
+ mmc_wait_for_req(host, &mrq);
+
+ if (cmd.error) {
+ err = cmd.error;
+ goto out;
+ }
+
+ if (data.error) {
+ err = data.error;
+ goto out;
+ }
+
+ if (memcmp(data_buf, tuning_block_pattern, size))
+ err = -EIO;
+
+out:
+ kfree(data_buf);
+ return err;
+}
+EXPORT_SYMBOL_GPL(mmc_send_tuning);
+
static int
mmc_send_bus_test(struct mmc_card *card, struct mmc_host *host, u8 opcode,
u8 len)
return 0;
}
+
+int mmc_can_ext_csd(struct mmc_card *card)
+{
+ return (card && card->csd.mmca_vsn > CSD_SPEC_VER_3);
+}
int mmc_all_send_cid(struct mmc_host *host, u32 *cid);
int mmc_set_relative_addr(struct mmc_card *card);
int mmc_send_csd(struct mmc_card *card, u32 *csd);
-int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd);
int mmc_send_status(struct mmc_card *card, u32 *status);
int mmc_send_cid(struct mmc_host *host, u32 *cid);
int mmc_spi_read_ocr(struct mmc_host *host, int highcap, u32 *ocrp);
int mmc_spi_set_crc(struct mmc_host *host, int use_crc);
int mmc_bus_test(struct mmc_card *card, u8 bus_width);
int mmc_send_hpi_cmd(struct mmc_card *card, u32 *status);
+int mmc_can_ext_csd(struct mmc_card *card);
#endif
if (mmc_card_is_removable(host) || !mmc_card_keep_power(host)) {
sdio_reset(host);
mmc_go_idle(host);
- err = mmc_sdio_init_card(host, host->card->ocr, host->card,
- mmc_card_keep_power(host));
+ mmc_send_if_cond(host, host->card->ocr);
+ err = mmc_send_io_op_cond(host, 0, NULL);
+ if (!err)
+ err = mmc_sdio_init_card(host, host->card->ocr,
+ host->card,
+ mmc_card_keep_power(host));
} else if (mmc_card_keep_power(host) && mmc_card_wake_sdio_irq(host)) {
/* We may have switched to 1-bit mode during suspend */
err = sdio_enable_4bit_bus(host->card);
sdio_reset(host);
mmc_go_idle(host);
- mmc_send_if_cond(host, host->ocr_avail);
+ mmc_send_if_cond(host, host->card->ocr);
ret = mmc_send_io_op_cond(host, 0, NULL);
if (ret)
#include "sdio_cis.h"
#include "sdio_bus.h"
+#define to_sdio_driver(d) container_of(d, struct sdio_driver, drv)
+
/* show configuration fields */
#define sdio_config_attr(field, format_string) \
static ssize_t \
return ret;
}
-#ifdef CONFIG_PM
-
static const struct dev_pm_ops sdio_bus_pm_ops = {
SET_SYSTEM_SLEEP_PM_OPS(pm_generic_suspend, pm_generic_resume)
SET_RUNTIME_PM_OPS(
)
};
-#define SDIO_PM_OPS_PTR (&sdio_bus_pm_ops)
-
-#else /* !CONFIG_PM */
-
-#define SDIO_PM_OPS_PTR NULL
-
-#endif /* !CONFIG_PM */
-
static struct bus_type sdio_bus_type = {
.name = "sdio",
.dev_groups = sdio_dev_groups,
.uevent = sdio_bus_uevent,
.probe = sdio_bus_probe,
.remove = sdio_bus_remove,
- .pm = SDIO_PM_OPS_PTR,
+ .pm = &sdio_bus_pm_ops,
};
int sdio_register_bus(void)
static void sdio_acpi_set_handle(struct sdio_func *func)
{
struct mmc_host *host = func->card->host;
- u64 addr = (host->slotno << 16) | func->num;
+ u64 addr = ((u64)host->slotno << 16) | func->num;
acpi_preset_companion(&func->dev, ACPI_COMPANION(host->parent), addr);
}
config MMC_DW
tristate "Synopsys DesignWare Memory Card Interface"
depends on HAS_DMA
- depends on ARC || ARM || MIPS || COMPILE_TEST
+ depends on ARC || ARM || ARM64 || MIPS || COMPILE_TEST
help
This selects support for the Synopsys DesignWare Mobile Storage IP
block, this provides host support for SD and MMC interfaces, in both
help
This selects support for the SD/MMC Host Controller on
Allwinner sunxi SoCs.
+
+config MMC_TOSHIBA_PCI
+ tristate "Toshiba Type A SD/MMC Card Interface Driver"
+ depends on PCI
+ help
obj-$(CONFIG_MMC_MOXART) += moxart-mmc.o
obj-$(CONFIG_MMC_SUNXI) += sunxi-mmc.o
obj-$(CONFIG_MMC_USDHI6ROL0) += usdhi6rol0.o
+obj-$(CONFIG_MMC_TOSHIBA_PCI) += toshsd.o
obj-$(CONFIG_MMC_REALTEK_PCI) += rtsx_pci_sdmmc.o
obj-$(CONFIG_MMC_REALTEK_USB) += rtsx_usb_sdmmc.o
#include <linux/stat.h>
#include <linux/types.h>
#include <linux/platform_data/atmel.h>
+#include <linux/platform_data/mmc-atmel-mci.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sdio.h>
-#include <mach/atmel-mci.h>
#include <linux/atmel-mci.h>
#include <linux/atmel_pdc.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/pinctrl/consumer.h>
#include <asm/cacheflush.h>
#include <asm/io.h>
#include "atmel-mci-regs.h"
+#define AUTOSUSPEND_DELAY 50
+
#define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
#define ATMCI_DMA_THRESHOLD 16
if (!buf)
return -ENOMEM;
+ pm_runtime_get_sync(&host->pdev->dev);
+
/*
* Grab a more or less consistent snapshot. Note that we're
* not disabling interrupts, so IMR and SR may not be
* consistent.
*/
- ret = clk_prepare_enable(host->mck);
- if (ret)
- goto out;
-
spin_lock_bh(&host->lock);
memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
spin_unlock_bh(&host->lock);
- clk_disable_unprepare(host->mck);
+ pm_runtime_mark_last_busy(&host->pdev->dev);
+ pm_runtime_put_autosuspend(&host->pdev->dev);
seq_printf(s, "MR:\t0x%08x%s%s ",
buf[ATMCI_MR / 4],
val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
}
-out:
kfree(buf);
return ret;
pdata->slot[slot_id].detect_is_active_high =
of_property_read_bool(cnp, "cd-inverted");
+ pdata->slot[slot_id].non_removable =
+ of_property_read_bool(cnp, "non-removable");
+
pdata->slot[slot_id].wp_pin =
of_get_named_gpio(cnp, "wp-gpios", 0);
}
WARN_ON(slot->mrq);
dev_dbg(&host->pdev->dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
+ pm_runtime_get_sync(&host->pdev->dev);
+
/*
* We may "know" the card is gone even though there's still an
* electrical connection. If so, we really need to communicate
struct atmel_mci_slot *slot = mmc_priv(mmc);
struct atmel_mci *host = slot->host;
unsigned int i;
- bool unprepare_clk;
+
+ pm_runtime_get_sync(&host->pdev->dev);
slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
switch (ios->bus_width) {
unsigned int clock_min = ~0U;
u32 clkdiv;
- clk_prepare(host->mck);
- unprepare_clk = true;
-
spin_lock_bh(&host->lock);
if (!host->mode_reg) {
- clk_enable(host->mck);
- unprepare_clk = false;
atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
if (host->caps.has_cfg_reg)
} else {
bool any_slot_active = false;
- unprepare_clk = false;
-
spin_lock_bh(&host->lock);
slot->clock = 0;
for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
if (host->mode_reg) {
atmci_readl(host, ATMCI_MR);
- clk_disable(host->mck);
- unprepare_clk = true;
}
host->mode_reg = 0;
}
spin_unlock_bh(&host->lock);
}
- if (unprepare_clk)
- clk_unprepare(host->mck);
-
switch (ios->power_mode) {
case MMC_POWER_OFF:
if (!IS_ERR(mmc->supply.vmmc))
*/
break;
}
+
+ pm_runtime_mark_last_busy(&host->pdev->dev);
+ pm_runtime_put_autosuspend(&host->pdev->dev);
}
static int atmci_get_ro(struct mmc_host *mmc)
spin_unlock(&host->lock);
mmc_request_done(prev_mmc, mrq);
spin_lock(&host->lock);
+
+ pm_runtime_mark_last_busy(&host->pdev->dev);
+ pm_runtime_put_autosuspend(&host->pdev->dev);
}
static void atmci_command_complete(struct atmel_mci *host,
return IRQ_HANDLED;
}
-static int __init atmci_init_slot(struct atmel_mci *host,
+static int atmci_init_slot(struct atmel_mci *host,
struct mci_slot_pdata *slot_data, unsigned int id,
u32 sdc_reg, u32 sdio_irq)
{
}
}
- if (!gpio_is_valid(slot->detect_pin))
- mmc->caps |= MMC_CAP_NEEDS_POLL;
+ if (!gpio_is_valid(slot->detect_pin)) {
+ if (slot_data->non_removable)
+ mmc->caps |= MMC_CAP_NONREMOVABLE;
+ else
+ mmc->caps |= MMC_CAP_NEEDS_POLL;
+ }
if (gpio_is_valid(slot->wp_pin)) {
if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
mmc_free_host(slot->mmc);
}
-static bool atmci_filter(struct dma_chan *chan, void *pdata)
+static int atmci_configure_dma(struct atmel_mci *host)
{
- struct mci_platform_data *sl_pdata = pdata;
- struct mci_dma_data *sl;
-
- if (!sl_pdata)
- return false;
+ host->dma.chan = dma_request_slave_channel_reason(&host->pdev->dev,
+ "rxtx");
+ if (IS_ERR(host->dma.chan))
+ return PTR_ERR(host->dma.chan);
+
+ dev_info(&host->pdev->dev, "using %s for DMA transfers\n",
+ dma_chan_name(host->dma.chan));
+
+ host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
+ host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ host->dma_conf.src_maxburst = 1;
+ host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
+ host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+ host->dma_conf.dst_maxburst = 1;
+ host->dma_conf.device_fc = false;
- sl = sl_pdata->dma_slave;
- if (sl && find_slave_dev(sl) == chan->device->dev) {
- chan->private = slave_data_ptr(sl);
- return true;
- } else {
- return false;
- }
-}
-
-static bool atmci_configure_dma(struct atmel_mci *host)
-{
- struct mci_platform_data *pdata;
- dma_cap_mask_t mask;
-
- if (host == NULL)
- return false;
-
- pdata = host->pdev->dev.platform_data;
-
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
-
- host->dma.chan = dma_request_slave_channel_compat(mask, atmci_filter, pdata,
- &host->pdev->dev, "rxtx");
- if (!host->dma.chan) {
- dev_warn(&host->pdev->dev, "no DMA channel available\n");
- return false;
- } else {
- dev_info(&host->pdev->dev,
- "using %s for DMA transfers\n",
- dma_chan_name(host->dma.chan));
-
- host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
- host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- host->dma_conf.src_maxburst = 1;
- host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
- host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
- host->dma_conf.dst_maxburst = 1;
- host->dma_conf.device_fc = false;
- return true;
- }
+ return 0;
}
/*
* HSMCI provides DMA support and a new config register but no more supports
* PDC.
*/
-static void __init atmci_get_cap(struct atmel_mci *host)
+static void atmci_get_cap(struct atmel_mci *host)
{
unsigned int version;
}
}
-static int __init atmci_probe(struct platform_device *pdev)
+static int atmci_probe(struct platform_device *pdev)
{
struct mci_platform_data *pdata;
struct atmel_mci *host;
atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
host->bus_hz = clk_get_rate(host->mck);
- clk_disable_unprepare(host->mck);
host->mapbase = regs->start;
tasklet_init(&host->tasklet, atmci_tasklet_func, (unsigned long)host);
ret = request_irq(irq, atmci_interrupt, 0, dev_name(&pdev->dev), host);
- if (ret)
+ if (ret) {
+ clk_disable_unprepare(host->mck);
return ret;
+ }
/* Get MCI capabilities and set operations according to it */
atmci_get_cap(host);
- if (atmci_configure_dma(host)) {
+ ret = atmci_configure_dma(host);
+ if (ret == -EPROBE_DEFER)
+ goto err_dma_probe_defer;
+ if (ret == 0) {
host->prepare_data = &atmci_prepare_data_dma;
host->submit_data = &atmci_submit_data_dma;
host->stop_transfer = &atmci_stop_transfer_dma;
setup_timer(&host->timer, atmci_timeout_timer, (unsigned long)host);
+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_DELAY);
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
/* We need at least one slot to succeed */
nr_slots = 0;
ret = -ENODEV;
"Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
host->mapbase, irq, nr_slots);
+ pm_runtime_mark_last_busy(&host->pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
return 0;
err_dma_alloc:
atmci_cleanup_slot(host->slot[i], i);
}
err_init_slot:
+ clk_disable_unprepare(host->mck);
+
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
del_timer_sync(&host->timer);
- if (host->dma.chan)
+ if (!IS_ERR(host->dma.chan))
dma_release_channel(host->dma.chan);
+err_dma_probe_defer:
free_irq(irq, host);
return ret;
}
-static int __exit atmci_remove(struct platform_device *pdev)
+static int atmci_remove(struct platform_device *pdev)
{
struct atmel_mci *host = platform_get_drvdata(pdev);
unsigned int i;
+ pm_runtime_get_sync(&pdev->dev);
+
if (host->buffer)
dma_free_coherent(&pdev->dev, host->buf_size,
host->buffer, host->buf_phys_addr);
atmci_cleanup_slot(host->slot[i], i);
}
- clk_prepare_enable(host->mck);
atmci_writel(host, ATMCI_IDR, ~0UL);
atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
atmci_readl(host, ATMCI_SR);
- clk_disable_unprepare(host->mck);
del_timer_sync(&host->timer);
- if (host->dma.chan)
+ if (!IS_ERR(host->dma.chan))
dma_release_channel(host->dma.chan);
free_irq(platform_get_irq(pdev, 0), host);
+ clk_disable_unprepare(host->mck);
+
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+
return 0;
}
-static struct platform_driver atmci_driver = {
- .remove = __exit_p(atmci_remove),
- .driver = {
- .name = "atmel_mci",
- .of_match_table = of_match_ptr(atmci_dt_ids),
- },
-};
-
-static int __init atmci_init(void)
+#ifdef CONFIG_PM
+static int atmci_runtime_suspend(struct device *dev)
{
- return platform_driver_probe(&atmci_driver, atmci_probe);
+ struct atmel_mci *host = dev_get_drvdata(dev);
+
+ clk_disable_unprepare(host->mck);
+
+ pinctrl_pm_select_sleep_state(dev);
+
+ return 0;
}
-static void __exit atmci_exit(void)
+static int atmci_runtime_resume(struct device *dev)
{
- platform_driver_unregister(&atmci_driver);
+ struct atmel_mci *host = dev_get_drvdata(dev);
+
+ pinctrl_pm_select_default_state(dev);
+
+ return clk_prepare_enable(host->mck);
}
+#endif
-late_initcall(atmci_init); /* try to load after dma driver when built-in */
-module_exit(atmci_exit);
+static const struct dev_pm_ops atmci_dev_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
+ pm_runtime_force_resume)
+ SET_PM_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
+};
+
+static struct platform_driver atmci_driver = {
+ .probe = atmci_probe,
+ .remove = atmci_remove,
+ .driver = {
+ .name = "atmel_mci",
+ .of_match_table = of_match_ptr(atmci_dt_ids),
+ .pm = &atmci_dev_pm_ops,
+ },
+};
+module_platform_driver(atmci_driver);
MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
#define NUM_PINS(x) (x + 2)
#define SDMMC_CLKSEL 0x09C
+#define SDMMC_CLKSEL64 0x0A8
#define SDMMC_CLKSEL_CCLK_SAMPLE(x) (((x) & 7) << 0)
#define SDMMC_CLKSEL_CCLK_DRIVE(x) (((x) & 7) << 16)
#define SDMMC_CLKSEL_CCLK_DIVIDER(x) (((x) & 7) << 24)
DW_MCI_TYPE_EXYNOS5250,
DW_MCI_TYPE_EXYNOS5420,
DW_MCI_TYPE_EXYNOS5420_SMU,
+ DW_MCI_TYPE_EXYNOS7,
+ DW_MCI_TYPE_EXYNOS7_SMU,
};
/* Exynos implementation specific driver private data */
}, {
.compatible = "samsung,exynos5420-dw-mshc-smu",
.ctrl_type = DW_MCI_TYPE_EXYNOS5420_SMU,
+ }, {
+ .compatible = "samsung,exynos7-dw-mshc",
+ .ctrl_type = DW_MCI_TYPE_EXYNOS7,
+ }, {
+ .compatible = "samsung,exynos7-dw-mshc-smu",
+ .ctrl_type = DW_MCI_TYPE_EXYNOS7_SMU,
},
};
{
struct dw_mci_exynos_priv_data *priv = host->priv;
- if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS5420_SMU) {
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS5420_SMU ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU) {
mci_writel(host, MPSBEGIN0, 0);
mci_writel(host, MPSEND0, DWMCI_BLOCK_NUM);
mci_writel(host, MPSCTRL0, DWMCI_MPSCTRL_SECURE_WRITE_BIT |
static int dw_mci_exynos_resume_noirq(struct device *dev)
{
struct dw_mci *host = dev_get_drvdata(dev);
+ struct dw_mci_exynos_priv_data *priv = host->priv;
u32 clksel;
- clksel = mci_readl(host, CLKSEL);
- if (clksel & SDMMC_CLKSEL_WAKEUP_INT)
- mci_writel(host, CLKSEL, clksel);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ clksel = mci_readl(host, CLKSEL64);
+ else
+ clksel = mci_readl(host, CLKSEL);
+
+ if (clksel & SDMMC_CLKSEL_WAKEUP_INT) {
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ mci_writel(host, CLKSEL64, clksel);
+ else
+ mci_writel(host, CLKSEL, clksel);
+ }
return 0;
}
static void dw_mci_exynos_prepare_command(struct dw_mci *host, u32 *cmdr)
{
+ struct dw_mci_exynos_priv_data *priv = host->priv;
/*
* Exynos4412 and Exynos5250 extends the use of CMD register with the
* use of bit 29 (which is reserved on standard MSHC controllers) for
* HOLD register should be bypassed in case there is no phase shift
* applied on CMD/DATA that is sent to the card.
*/
- if (SDMMC_CLKSEL_GET_DRV_WD3(mci_readl(host, CLKSEL)))
- *cmdr |= SDMMC_CMD_USE_HOLD_REG;
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU) {
+ if (SDMMC_CLKSEL_GET_DRV_WD3(mci_readl(host, CLKSEL64)))
+ *cmdr |= SDMMC_CMD_USE_HOLD_REG;
+ } else {
+ if (SDMMC_CLKSEL_GET_DRV_WD3(mci_readl(host, CLKSEL)))
+ *cmdr |= SDMMC_CMD_USE_HOLD_REG;
+ }
}
static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
u8 div = priv->ciu_div + 1;
if (ios->timing == MMC_TIMING_MMC_DDR52) {
- mci_writel(host, CLKSEL, priv->ddr_timing);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ mci_writel(host, CLKSEL64, priv->ddr_timing);
+ else
+ mci_writel(host, CLKSEL, priv->ddr_timing);
/* Should be double rate for DDR mode */
if (ios->bus_width == MMC_BUS_WIDTH_8)
wanted <<= 1;
} else {
- mci_writel(host, CLKSEL, priv->sdr_timing);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ mci_writel(host, CLKSEL64, priv->sdr_timing);
+ else
+ mci_writel(host, CLKSEL, priv->sdr_timing);
}
/* Don't care if wanted clock is zero */
static inline u8 dw_mci_exynos_get_clksmpl(struct dw_mci *host)
{
- return SDMMC_CLKSEL_CCLK_SAMPLE(mci_readl(host, CLKSEL));
+ struct dw_mci_exynos_priv_data *priv = host->priv;
+
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ return SDMMC_CLKSEL_CCLK_SAMPLE(mci_readl(host, CLKSEL64));
+ else
+ return SDMMC_CLKSEL_CCLK_SAMPLE(mci_readl(host, CLKSEL));
}
static inline void dw_mci_exynos_set_clksmpl(struct dw_mci *host, u8 sample)
{
u32 clksel;
- clksel = mci_readl(host, CLKSEL);
+ struct dw_mci_exynos_priv_data *priv = host->priv;
+
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ clksel = mci_readl(host, CLKSEL64);
+ else
+ clksel = mci_readl(host, CLKSEL);
clksel = (clksel & ~0x7) | SDMMC_CLKSEL_CCLK_SAMPLE(sample);
- mci_writel(host, CLKSEL, clksel);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ mci_writel(host, CLKSEL64, clksel);
+ else
+ mci_writel(host, CLKSEL, clksel);
}
static inline u8 dw_mci_exynos_move_next_clksmpl(struct dw_mci *host)
{
+ struct dw_mci_exynos_priv_data *priv = host->priv;
u32 clksel;
u8 sample;
- clksel = mci_readl(host, CLKSEL);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ clksel = mci_readl(host, CLKSEL64);
+ else
+ clksel = mci_readl(host, CLKSEL);
sample = (clksel + 1) & 0x7;
clksel = (clksel & ~0x7) | sample;
- mci_writel(host, CLKSEL, clksel);
+ if (priv->ctrl_type == DW_MCI_TYPE_EXYNOS7 ||
+ priv->ctrl_type == DW_MCI_TYPE_EXYNOS7_SMU)
+ mci_writel(host, CLKSEL64, clksel);
+ else
+ mci_writel(host, CLKSEL, clksel);
return sample;
}
.data = &exynos_drv_data, },
{ .compatible = "samsung,exynos5420-dw-mshc-smu",
.data = &exynos_drv_data, },
+ { .compatible = "samsung,exynos7-dw-mshc",
+ .data = &exynos_drv_data, },
+ { .compatible = "samsung,exynos7-dw-mshc-smu",
+ .data = &exynos_drv_data, },
{},
};
MODULE_DEVICE_TABLE(of, dw_mci_exynos_match);
.prepare_command = dw_mci_pltfm_prepare_command,
};
+static const struct dw_mci_drv_data pistachio_drv_data = {
+ .prepare_command = dw_mci_pltfm_prepare_command,
+};
+
int dw_mci_pltfm_register(struct platform_device *pdev,
const struct dw_mci_drv_data *drv_data)
{
{ .compatible = "snps,dw-mshc", },
{ .compatible = "altr,socfpga-dw-mshc",
.data = &socfpga_drv_data },
+ { .compatible = "img,pistachio-dw-mshc",
+ .data = &pistachio_drv_data },
{},
};
MODULE_DEVICE_TABLE(of, dw_mci_pltfm_match);
unsigned int cclkin;
u32 bus_hz;
+ if (ios->clock == 0)
+ return;
+
/*
* cclkin: source clock of mmc controller
* bus_hz: card interface clock generated by CLKGEN
}
}
+static int dw_mci_rockchip_init(struct dw_mci *host)
+{
+ /* It is slot 8 on Rockchip SoCs */
+ host->sdio_id0 = 8;
+
+ return 0;
+}
+
static const struct dw_mci_drv_data rk2928_drv_data = {
.prepare_command = dw_mci_rockchip_prepare_command,
+ .init = dw_mci_rockchip_init,
};
static const struct dw_mci_drv_data rk3288_drv_data = {
.prepare_command = dw_mci_rockchip_prepare_command,
.set_ios = dw_mci_rk3288_set_ios,
.setup_clock = dw_mci_rk3288_setup_clock,
+ .init = dw_mci_rockchip_init,
};
static const struct of_device_id dw_mci_rockchip_match[] = {
#include <linux/mmc/dw_mmc.h>
#include <linux/bitops.h>
#include <linux/regulator/consumer.h>
-#include <linux/workqueue.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/mmc/slot-gpio.h>
SDMMC_IDMAC_INT_FBE | SDMMC_IDMAC_INT_RI | \
SDMMC_IDMAC_INT_TI)
+struct idmac_desc_64addr {
+ u32 des0; /* Control Descriptor */
+
+ u32 des1; /* Reserved */
+
+ u32 des2; /*Buffer sizes */
+#define IDMAC_64ADDR_SET_BUFFER1_SIZE(d, s) \
+ ((d)->des2 = ((d)->des2 & 0x03ffe000) | ((s) & 0x1fff))
+
+ u32 des3; /* Reserved */
+
+ u32 des4; /* Lower 32-bits of Buffer Address Pointer 1*/
+ u32 des5; /* Upper 32-bits of Buffer Address Pointer 1*/
+
+ u32 des6; /* Lower 32-bits of Next Descriptor Address */
+ u32 des7; /* Upper 32-bits of Next Descriptor Address */
+};
+
struct idmac_desc {
u32 des0; /* Control Descriptor */
#define IDMAC_DES0_DIC BIT(1)
#endif /* CONFIG_MMC_DW_IDMAC */
static bool dw_mci_reset(struct dw_mci *host);
+static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
#if defined(CONFIG_DEBUG_FS)
static int dw_mci_req_show(struct seq_file *s, void *v)
unsigned int sg_len)
{
int i;
- struct idmac_desc *desc = host->sg_cpu;
+ if (host->dma_64bit_address == 1) {
+ struct idmac_desc_64addr *desc = host->sg_cpu;
- for (i = 0; i < sg_len; i++, desc++) {
- unsigned int length = sg_dma_len(&data->sg[i]);
- u32 mem_addr = sg_dma_address(&data->sg[i]);
+ for (i = 0; i < sg_len; i++, desc++) {
+ unsigned int length = sg_dma_len(&data->sg[i]);
+ u64 mem_addr = sg_dma_address(&data->sg[i]);
- /* Set the OWN bit and disable interrupts for this descriptor */
- desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC | IDMAC_DES0_CH;
+ /*
+ * Set the OWN bit and disable interrupts for this
+ * descriptor
+ */
+ desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
+ IDMAC_DES0_CH;
+ /* Buffer length */
+ IDMAC_64ADDR_SET_BUFFER1_SIZE(desc, length);
+
+ /* Physical address to DMA to/from */
+ desc->des4 = mem_addr & 0xffffffff;
+ desc->des5 = mem_addr >> 32;
+ }
- /* Buffer length */
- IDMAC_SET_BUFFER1_SIZE(desc, length);
+ /* Set first descriptor */
+ desc = host->sg_cpu;
+ desc->des0 |= IDMAC_DES0_FD;
- /* Physical address to DMA to/from */
- desc->des2 = mem_addr;
- }
+ /* Set last descriptor */
+ desc = host->sg_cpu + (i - 1) *
+ sizeof(struct idmac_desc_64addr);
+ desc->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
+ desc->des0 |= IDMAC_DES0_LD;
- /* Set first descriptor */
- desc = host->sg_cpu;
- desc->des0 |= IDMAC_DES0_FD;
+ } else {
+ struct idmac_desc *desc = host->sg_cpu;
+
+ for (i = 0; i < sg_len; i++, desc++) {
+ unsigned int length = sg_dma_len(&data->sg[i]);
+ u32 mem_addr = sg_dma_address(&data->sg[i]);
+
+ /*
+ * Set the OWN bit and disable interrupts for this
+ * descriptor
+ */
+ desc->des0 = IDMAC_DES0_OWN | IDMAC_DES0_DIC |
+ IDMAC_DES0_CH;
+ /* Buffer length */
+ IDMAC_SET_BUFFER1_SIZE(desc, length);
- /* Set last descriptor */
- desc = host->sg_cpu + (i - 1) * sizeof(struct idmac_desc);
- desc->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
- desc->des0 |= IDMAC_DES0_LD;
+ /* Physical address to DMA to/from */
+ desc->des2 = mem_addr;
+ }
+
+ /* Set first descriptor */
+ desc = host->sg_cpu;
+ desc->des0 |= IDMAC_DES0_FD;
+
+ /* Set last descriptor */
+ desc = host->sg_cpu + (i - 1) * sizeof(struct idmac_desc);
+ desc->des0 &= ~(IDMAC_DES0_CH | IDMAC_DES0_DIC);
+ desc->des0 |= IDMAC_DES0_LD;
+ }
wmb();
}
dw_mci_translate_sglist(host, host->data, sg_len);
+ /* Make sure to reset DMA in case we did PIO before this */
+ dw_mci_ctrl_reset(host, SDMMC_CTRL_DMA_RESET);
+ dw_mci_idmac_reset(host);
+
/* Select IDMAC interface */
temp = mci_readl(host, CTRL);
temp |= SDMMC_CTRL_USE_IDMAC;
static int dw_mci_idmac_init(struct dw_mci *host)
{
- struct idmac_desc *p;
int i;
- /* Number of descriptors in the ring buffer */
- host->ring_size = PAGE_SIZE / sizeof(struct idmac_desc);
+ if (host->dma_64bit_address == 1) {
+ struct idmac_desc_64addr *p;
+ /* Number of descriptors in the ring buffer */
+ host->ring_size = PAGE_SIZE / sizeof(struct idmac_desc_64addr);
+
+ /* Forward link the descriptor list */
+ for (i = 0, p = host->sg_cpu; i < host->ring_size - 1;
+ i++, p++) {
+ p->des6 = (host->sg_dma +
+ (sizeof(struct idmac_desc_64addr) *
+ (i + 1))) & 0xffffffff;
+
+ p->des7 = (u64)(host->sg_dma +
+ (sizeof(struct idmac_desc_64addr) *
+ (i + 1))) >> 32;
+ /* Initialize reserved and buffer size fields to "0" */
+ p->des1 = 0;
+ p->des2 = 0;
+ p->des3 = 0;
+ }
+
+ /* Set the last descriptor as the end-of-ring descriptor */
+ p->des6 = host->sg_dma & 0xffffffff;
+ p->des7 = (u64)host->sg_dma >> 32;
+ p->des0 = IDMAC_DES0_ER;
+
+ } else {
+ struct idmac_desc *p;
+ /* Number of descriptors in the ring buffer */
+ host->ring_size = PAGE_SIZE / sizeof(struct idmac_desc);
- /* Forward link the descriptor list */
- for (i = 0, p = host->sg_cpu; i < host->ring_size - 1; i++, p++)
- p->des3 = host->sg_dma + (sizeof(struct idmac_desc) * (i + 1));
+ /* Forward link the descriptor list */
+ for (i = 0, p = host->sg_cpu; i < host->ring_size - 1; i++, p++)
+ p->des3 = host->sg_dma + (sizeof(struct idmac_desc) *
+ (i + 1));
- /* Set the last descriptor as the end-of-ring descriptor */
- p->des3 = host->sg_dma;
- p->des0 = IDMAC_DES0_ER;
+ /* Set the last descriptor as the end-of-ring descriptor */
+ p->des3 = host->sg_dma;
+ p->des0 = IDMAC_DES0_ER;
+ }
dw_mci_idmac_reset(host);
- /* Mask out interrupts - get Tx & Rx complete only */
- mci_writel(host, IDSTS, IDMAC_INT_CLR);
- mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI | SDMMC_IDMAC_INT_RI |
- SDMMC_IDMAC_INT_TI);
+ if (host->dma_64bit_address == 1) {
+ /* Mask out interrupts - get Tx & Rx complete only */
+ mci_writel(host, IDSTS64, IDMAC_INT_CLR);
+ mci_writel(host, IDINTEN64, SDMMC_IDMAC_INT_NI |
+ SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
+
+ /* Set the descriptor base address */
+ mci_writel(host, DBADDRL, host->sg_dma & 0xffffffff);
+ mci_writel(host, DBADDRU, (u64)host->sg_dma >> 32);
+
+ } else {
+ /* Mask out interrupts - get Tx & Rx complete only */
+ mci_writel(host, IDSTS, IDMAC_INT_CLR);
+ mci_writel(host, IDINTEN, SDMMC_IDMAC_INT_NI |
+ SDMMC_IDMAC_INT_RI | SDMMC_IDMAC_INT_TI);
+
+ /* Set the descriptor base address */
+ mci_writel(host, DBADDR, host->sg_dma);
+ }
- /* Set the descriptor base address */
- mci_writel(host, DBADDR, host->sg_dma);
return 0;
}
WARN_ON(!(data->flags & MMC_DATA_READ));
+ /*
+ * CDTHRCTL doesn't exist prior to 240A (in fact that register offset is
+ * in the FIFO region, so we really shouldn't access it).
+ */
+ if (host->verid < DW_MMC_240A)
+ return;
+
if (host->timing != MMC_TIMING_MMC_HS200 &&
host->timing != MMC_TIMING_UHS_SDR104)
goto disable;
/* enable clock; only low power if no SDIO */
clk_en_a = SDMMC_CLKEN_ENABLE << slot->id;
- if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->id)))
+ if (!(mci_readl(host, INTMASK) & SDMMC_INT_SDIO(slot->sdio_id)))
clk_en_a |= SDMMC_CLKEN_LOW_PWR << slot->id;
mci_writel(host, CLKENA, clk_en_a);
ret = regulator_set_voltage(mmc->supply.vqmmc, min_uv, max_uv);
if (ret) {
- dev_err(&mmc->class_dev,
+ dev_dbg(&mmc->class_dev,
"Regulator set error %d: %d - %d\n",
ret, min_uv, max_uv);
return ret;
dw_mci_disable_low_power(slot);
mci_writel(host, INTMASK,
- (int_mask | SDMMC_INT_SDIO(slot->id)));
+ (int_mask | SDMMC_INT_SDIO(slot->sdio_id)));
} else {
mci_writel(host, INTMASK,
- (int_mask & ~SDMMC_INT_SDIO(slot->id)));
+ (int_mask & ~SDMMC_INT_SDIO(slot->sdio_id)));
}
}
tasklet_schedule(&host->tasklet);
}
+static void dw_mci_handle_cd(struct dw_mci *host)
+{
+ int i;
+
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+
+ if (!slot)
+ continue;
+
+ if (slot->mmc->ops->card_event)
+ slot->mmc->ops->card_event(slot->mmc);
+ mmc_detect_change(slot->mmc,
+ msecs_to_jiffies(host->pdata->detect_delay_ms));
+ }
+}
+
static irqreturn_t dw_mci_interrupt(int irq, void *dev_id)
{
struct dw_mci *host = dev_id;
if (pending & SDMMC_INT_CD) {
mci_writel(host, RINTSTS, SDMMC_INT_CD);
- queue_work(host->card_workqueue, &host->card_work);
+ dw_mci_handle_cd(host);
}
/* Handle SDIO Interrupts */
for (i = 0; i < host->num_slots; i++) {
struct dw_mci_slot *slot = host->slot[i];
- if (pending & SDMMC_INT_SDIO(i)) {
- mci_writel(host, RINTSTS, SDMMC_INT_SDIO(i));
+ if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
+ mci_writel(host, RINTSTS,
+ SDMMC_INT_SDIO(slot->sdio_id));
mmc_signal_sdio_irq(slot->mmc);
}
}
#ifdef CONFIG_MMC_DW_IDMAC
/* Handle DMA interrupts */
- pending = mci_readl(host, IDSTS);
- if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
- mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI);
- mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
- host->dma_ops->complete(host);
+ if (host->dma_64bit_address == 1) {
+ pending = mci_readl(host, IDSTS64);
+ if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
+ mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_TI |
+ SDMMC_IDMAC_INT_RI);
+ mci_writel(host, IDSTS64, SDMMC_IDMAC_INT_NI);
+ host->dma_ops->complete(host);
+ }
+ } else {
+ pending = mci_readl(host, IDSTS);
+ if (pending & (SDMMC_IDMAC_INT_TI | SDMMC_IDMAC_INT_RI)) {
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_TI |
+ SDMMC_IDMAC_INT_RI);
+ mci_writel(host, IDSTS, SDMMC_IDMAC_INT_NI);
+ host->dma_ops->complete(host);
+ }
}
#endif
return IRQ_HANDLED;
}
-static void dw_mci_work_routine_card(struct work_struct *work)
-{
- struct dw_mci *host = container_of(work, struct dw_mci, card_work);
- int i;
-
- for (i = 0; i < host->num_slots; i++) {
- struct dw_mci_slot *slot = host->slot[i];
- struct mmc_host *mmc = slot->mmc;
- struct mmc_request *mrq;
- int present;
-
- present = dw_mci_get_cd(mmc);
- while (present != slot->last_detect_state) {
- dev_dbg(&slot->mmc->class_dev, "card %s\n",
- present ? "inserted" : "removed");
-
- spin_lock_bh(&host->lock);
-
- /* Card change detected */
- slot->last_detect_state = present;
-
- /* Clean up queue if present */
- mrq = slot->mrq;
- if (mrq) {
- if (mrq == host->mrq) {
- host->data = NULL;
- host->cmd = NULL;
-
- switch (host->state) {
- case STATE_IDLE:
- case STATE_WAITING_CMD11_DONE:
- break;
- case STATE_SENDING_CMD11:
- case STATE_SENDING_CMD:
- mrq->cmd->error = -ENOMEDIUM;
- if (!mrq->data)
- break;
- /* fall through */
- case STATE_SENDING_DATA:
- mrq->data->error = -ENOMEDIUM;
- dw_mci_stop_dma(host);
- break;
- case STATE_DATA_BUSY:
- case STATE_DATA_ERROR:
- if (mrq->data->error == -EINPROGRESS)
- mrq->data->error = -ENOMEDIUM;
- /* fall through */
- case STATE_SENDING_STOP:
- if (mrq->stop)
- mrq->stop->error = -ENOMEDIUM;
- break;
- }
-
- dw_mci_request_end(host, mrq);
- } else {
- list_del(&slot->queue_node);
- mrq->cmd->error = -ENOMEDIUM;
- if (mrq->data)
- mrq->data->error = -ENOMEDIUM;
- if (mrq->stop)
- mrq->stop->error = -ENOMEDIUM;
-
- spin_unlock(&host->lock);
- mmc_request_done(slot->mmc, mrq);
- spin_lock(&host->lock);
- }
- }
-
- /* Power down slot */
- if (present == 0)
- dw_mci_reset(host);
-
- spin_unlock_bh(&host->lock);
-
- present = dw_mci_get_cd(mmc);
- }
-
- mmc_detect_change(slot->mmc,
- msecs_to_jiffies(host->pdata->detect_delay_ms));
- }
-}
-
#ifdef CONFIG_OF
/* given a slot id, find out the device node representing that slot */
static struct device_node *dw_mci_of_find_slot_node(struct device *dev, u8 slot)
slot = mmc_priv(mmc);
slot->id = id;
+ slot->sdio_id = host->sdio_id0 + id;
slot->mmc = mmc;
slot->host = host;
host->slot[id] = slot;
dw_mci_init_debugfs(slot);
#endif
- /* Card initially undetected */
- slot->last_detect_state = 0;
-
return 0;
err_host_allocated:
static void dw_mci_init_dma(struct dw_mci *host)
{
+ int addr_config;
+ /* Check ADDR_CONFIG bit in HCON to find IDMAC address bus width */
+ addr_config = (mci_readl(host, HCON) >> 27) & 0x01;
+
+ if (addr_config == 1) {
+ /* host supports IDMAC in 64-bit address mode */
+ host->dma_64bit_address = 1;
+ dev_info(host->dev, "IDMAC supports 64-bit address mode.\n");
+ if (!dma_set_mask(host->dev, DMA_BIT_MASK(64)))
+ dma_set_coherent_mask(host->dev, DMA_BIT_MASK(64));
+ } else {
+ /* host supports IDMAC in 32-bit address mode */
+ host->dma_64bit_address = 0;
+ dev_info(host->dev, "IDMAC supports 32-bit address mode.\n");
+ }
+
/* Alloc memory for sg translation */
host->sg_cpu = dmam_alloc_coherent(host->dev, PAGE_SIZE,
&host->sg_dma, GFP_KERNEL);
host->data_offset = DATA_240A_OFFSET;
tasklet_init(&host->tasklet, dw_mci_tasklet_func, (unsigned long)host);
- host->card_workqueue = alloc_workqueue("dw-mci-card",
- WQ_MEM_RECLAIM, 1);
- if (!host->card_workqueue) {
- ret = -ENOMEM;
- goto err_dmaunmap;
- }
- INIT_WORK(&host->card_work, dw_mci_work_routine_card);
ret = devm_request_irq(host->dev, host->irq, dw_mci_interrupt,
host->irq_flags, "dw-mci", host);
if (ret)
- goto err_workqueue;
+ goto err_dmaunmap;
if (host->pdata->num_slots)
host->num_slots = host->pdata->num_slots;
} else {
dev_dbg(host->dev, "attempted to initialize %d slots, "
"but failed on all\n", host->num_slots);
- goto err_workqueue;
+ goto err_dmaunmap;
}
if (host->quirks & DW_MCI_QUIRK_IDMAC_DTO)
return 0;
-err_workqueue:
- destroy_workqueue(host->card_workqueue);
-
err_dmaunmap:
if (host->use_dma && host->dma_ops->exit)
host->dma_ops->exit(host);
mci_writel(host, CLKENA, 0);
mci_writel(host, CLKSRC, 0);
- destroy_workqueue(host->card_workqueue);
-
if (host->use_dma && host->dma_ops->exit)
host->dma_ops->exit(host);
#define SDMMC_BUFADDR 0x098
#define SDMMC_CDTHRCTL 0x100
#define SDMMC_DATA(x) (x)
+/*
+* Registers to support idmac 64-bit address mode
+*/
+#define SDMMC_DBADDRL 0x088
+#define SDMMC_DBADDRU 0x08c
+#define SDMMC_IDSTS64 0x090
+#define SDMMC_IDINTEN64 0x094
+#define SDMMC_DSCADDRL 0x098
+#define SDMMC_DSCADDRU 0x09c
+#define SDMMC_BUFADDRL 0x0A0
+#define SDMMC_BUFADDRU 0x0A4
/*
* Data offset is difference according to Version
* with CONFIG_MMC_CLKGATE.
* @flags: Random state bits associated with the slot.
* @id: Number of this slot.
- * @last_detect_state: Most recently observed card detect state.
+ * @sdio_id: Number of this slot in the SDIO interrupt registers.
*/
struct dw_mci_slot {
struct mmc_host *mmc;
#define DW_MMC_CARD_PRESENT 0
#define DW_MMC_CARD_NEED_INIT 1
int id;
- int last_detect_state;
+ int sdio_id;
};
struct dw_mci_tuning_data {
chan = host->dma_tx_channel;
dmaengine_terminate_all(chan);
+ if (host->dma_desc_current == next->dma_desc)
+ host->dma_desc_current = NULL;
+
+ if (host->dma_current == next->dma_chan)
+ host->dma_current = NULL;
+
next->dma_desc = NULL;
next->dma_chan = NULL;
+ data->host_cookie = 0;
}
}
if (ret)
goto cmd_irq_free;
- mmc_set_drvdata(pdev, mmc);
+ platform_set_drvdata(pdev, mmc);
mmc_add_host(mmc);
pr_info("%s: Qualcomm MSM SDCC at 0x%016llx irq %d,%d dma %d\n",
static int
msmsdcc_suspend(struct platform_device *dev, pm_message_t state)
{
- struct mmc_host *mmc = mmc_get_drvdata(dev);
+ struct mmc_host *mmc = platform_get_drvdata(dev);
if (mmc) {
struct msmsdcc_host *host = mmc_priv(mmc);
static int
msmsdcc_resume(struct platform_device *dev)
{
- struct mmc_host *mmc = mmc_get_drvdata(dev);
+ struct mmc_host *mmc = platform_get_drvdata(dev);
if (mmc) {
struct msmsdcc_host *host = mmc_priv(mmc);
mvsd_write(MVSD_BLK_COUNT, data->blocks);
mvsd_write(MVSD_BLK_SIZE, data->blksz);
- if (nodma || (data->blksz | data->sg->offset) & 3) {
+ if (nodma || (data->blksz | data->sg->offset) & 3 ||
+ ((!(data->flags & MMC_DATA_READ) && data->sg->offset & 0x3f))) {
/*
* We cannot do DMA on a buffer which offset or size
* is not aligned on a 4-byte boundary.
+ *
+ * It also appears the host to card DMA can corrupt
+ * data when the buffer is not aligned on a 64 byte
+ * boundary.
*/
host->pio_size = data->blocks * data->blksz;
host->pio_ptr = sg_virt(data->sg);
del_timer(&host->watchdog);
stat = mxcmci_readl(host, MMC_REG_STATUS);
- mxcmci_writel(host, stat & ~STATUS_DATA_TRANS_DONE, MMC_REG_STATUS);
dev_dbg(mmc_dev(host->mmc), "%s: 0x%08x\n", __func__, stat);
- if (stat & STATUS_READ_OP_DONE)
- mxcmci_writel(host, STATUS_READ_OP_DONE, MMC_REG_STATUS);
-
mxcmci_data_done(host, stat);
}
sdio_irq = (stat & STATUS_SDIO_INT_ACTIVE) && host->use_sdio;
spin_unlock_irqrestore(&host->lock, flags);
- if (mxcmci_use_dma(host) &&
- (stat & (STATUS_READ_OP_DONE | STATUS_WRITE_OP_DONE)))
- mxcmci_writel(host, STATUS_READ_OP_DONE | STATUS_WRITE_OP_DONE,
- MMC_REG_STATUS);
+ if (mxcmci_use_dma(host) && (stat & (STATUS_WRITE_OP_DONE)))
+ mxcmci_writel(host, STATUS_WRITE_OP_DONE, MMC_REG_STATUS);
if (sdio_irq) {
mxcmci_writel(host, STATUS_SDIO_INT_ACTIVE, MMC_REG_STATUS);
if (stat & STATUS_END_CMD_RESP)
mxcmci_cmd_done(host, stat);
- if (mxcmci_use_dma(host) &&
- (stat & (STATUS_DATA_TRANS_DONE | STATUS_WRITE_OP_DONE))) {
+ if (mxcmci_use_dma(host) && (stat & STATUS_WRITE_OP_DONE)) {
del_timer(&host->watchdog);
mxcmci_data_done(host, stat);
}
dat3_card_detect = true;
ret = mmc_regulator_get_supply(mmc);
- if (ret) {
- if (pdata && ret != -EPROBE_DEFER)
- mmc->ocr_avail = pdata->ocr_avail ? :
- MMC_VDD_32_33 | MMC_VDD_33_34;
+ if (ret == -EPROBE_DEFER)
+ goto out_free;
+
+ if (!mmc->ocr_avail) {
+ if (pdata && pdata->ocr_avail)
+ mmc->ocr_avail = pdata->ocr_avail;
else
- goto out_free;
+ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
}
if (dat3_card_detect)
struct regulator *reg_vmmc;
struct mxs_ssp *ssp;
- iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq_err = platform_get_irq(pdev, 0);
- if (!iores || irq_err < 0)
- return -EINVAL;
+ if (irq_err < 0)
+ return irq_err;
mmc = mmc_alloc_host(sizeof(struct mxs_mmc_host), &pdev->dev);
if (!mmc)
host = mmc_priv(mmc);
ssp = &host->ssp;
ssp->dev = &pdev->dev;
+ iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
ssp->base = devm_ioremap_resource(&pdev->dev, iores);
if (IS_ERR(ssp->base)) {
ret = PTR_ERR(ssp->base);
ret = PTR_ERR(ssp->clk);
goto out_mmc_free;
}
- clk_prepare_enable(ssp->clk);
+ ret = clk_prepare_enable(ssp->clk);
+ if (ret)
+ goto out_mmc_free;
ret = mxs_mmc_reset(host);
if (ret) {
platform_set_drvdata(pdev, mmc);
ret = devm_request_irq(&pdev->dev, irq_err, mxs_mmc_irq_handler, 0,
- DRIVER_NAME, host);
+ dev_name(&pdev->dev), host);
if (ret)
goto out_free_dma;
return 0;
}
-#ifdef CONFIG_PM
+#ifdef CONFIG_PM_SLEEP
static int mxs_mmc_suspend(struct device *dev)
{
struct mmc_host *mmc = dev_get_drvdata(dev);
struct mxs_mmc_host *host = mmc_priv(mmc);
struct mxs_ssp *ssp = &host->ssp;
- clk_prepare_enable(ssp->clk);
- return 0;
+ return clk_prepare_enable(ssp->clk);
}
-
-static const struct dev_pm_ops mxs_mmc_pm_ops = {
- .suspend = mxs_mmc_suspend,
- .resume = mxs_mmc_resume,
-};
#endif
+static SIMPLE_DEV_PM_OPS(mxs_mmc_pm_ops, mxs_mmc_suspend, mxs_mmc_resume);
+
static struct platform_driver mxs_mmc_driver = {
.probe = mxs_mmc_probe,
.remove = mxs_mmc_remove,
.id_table = mxs_ssp_ids,
.driver = {
.name = DRIVER_NAME,
-#ifdef CONFIG_PM
.pm = &mxs_mmc_pm_ops,
-#endif
.of_match_table = mxs_mmc_dt_ids,
},
};
#include <linux/regulator/consumer.h>
#include <linux/pinctrl/consumer.h>
#include <linux/pm_runtime.h>
-#include <linux/platform_data/mmc-omap.h>
+#include <linux/platform_data/hsmmc-omap.h>
/* OMAP HSMMC Host Controller Registers */
#define OMAP_HSMMC_SYSSTATUS 0x0014
* omap.c controller driver. Luckily this is not currently done on any known
* omap_hsmmc.c device.
*/
-#define mmc_slot(host) (host->pdata->slots[host->slot_id])
+#define mmc_pdata(host) host->pdata
/*
* MMC Host controller read/write API's
int use_dma, dma_ch;
struct dma_chan *tx_chan;
struct dma_chan *rx_chan;
- int slot_id;
int response_busy;
int context_loss;
int protect_card;
#define HSMMC_SDIO_IRQ_ENABLED (1 << 1) /* SDIO irq enabled */
#define HSMMC_WAKE_IRQ_ENABLED (1 << 2)
struct omap_hsmmc_next next_data;
- struct omap_mmc_platform_data *pdata;
+ struct omap_hsmmc_platform_data *pdata;
+
+ /* To handle board related suspend/resume functionality for MMC */
+ int (*suspend)(struct device *dev);
+ int (*resume)(struct device *dev);
+
+ /* return MMC cover switch state, can be NULL if not supported.
+ *
+ * possible return values:
+ * 0 - closed
+ * 1 - open
+ */
+ int (*get_cover_state)(struct device *dev);
+
+ /* Card detection IRQs */
+ int card_detect_irq;
+
+ int (*card_detect)(struct device *dev);
+ int (*get_ro)(struct device *dev);
+
};
struct omap_mmc_of_data {
static void omap_hsmmc_start_dma_transfer(struct omap_hsmmc_host *host);
-static int omap_hsmmc_card_detect(struct device *dev, int slot)
+static int omap_hsmmc_card_detect(struct device *dev)
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- struct omap_mmc_platform_data *mmc = host->pdata;
+ struct omap_hsmmc_platform_data *mmc = host->pdata;
/* NOTE: assumes card detect signal is active-low */
- return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
+ return !gpio_get_value_cansleep(mmc->switch_pin);
}
-static int omap_hsmmc_get_wp(struct device *dev, int slot)
+static int omap_hsmmc_get_wp(struct device *dev)
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- struct omap_mmc_platform_data *mmc = host->pdata;
+ struct omap_hsmmc_platform_data *mmc = host->pdata;
/* NOTE: assumes write protect signal is active-high */
- return gpio_get_value_cansleep(mmc->slots[0].gpio_wp);
+ return gpio_get_value_cansleep(mmc->gpio_wp);
}
-static int omap_hsmmc_get_cover_state(struct device *dev, int slot)
+static int omap_hsmmc_get_cover_state(struct device *dev)
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- struct omap_mmc_platform_data *mmc = host->pdata;
+ struct omap_hsmmc_platform_data *mmc = host->pdata;
/* NOTE: assumes card detect signal is active-low */
- return !gpio_get_value_cansleep(mmc->slots[0].switch_pin);
+ return !gpio_get_value_cansleep(mmc->switch_pin);
}
#ifdef CONFIG_PM
-static int omap_hsmmc_suspend_cdirq(struct device *dev, int slot)
+static int omap_hsmmc_suspend_cdirq(struct device *dev)
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- struct omap_mmc_platform_data *mmc = host->pdata;
- disable_irq(mmc->slots[0].card_detect_irq);
+ disable_irq(host->card_detect_irq);
return 0;
}
-static int omap_hsmmc_resume_cdirq(struct device *dev, int slot)
+static int omap_hsmmc_resume_cdirq(struct device *dev)
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- struct omap_mmc_platform_data *mmc = host->pdata;
- enable_irq(mmc->slots[0].card_detect_irq);
+ enable_irq(host->card_detect_irq);
return 0;
}
#ifdef CONFIG_REGULATOR
-static int omap_hsmmc_set_power(struct device *dev, int slot, int power_on,
- int vdd)
+static int omap_hsmmc_set_power(struct device *dev, int power_on, int vdd)
{
struct omap_hsmmc_host *host =
platform_get_drvdata(to_platform_device(dev));
if (!host->vcc)
return 0;
- if (mmc_slot(host).before_set_reg)
- mmc_slot(host).before_set_reg(dev, slot, power_on, vdd);
+ if (mmc_pdata(host)->before_set_reg)
+ mmc_pdata(host)->before_set_reg(dev, power_on, vdd);
if (host->pbias) {
if (host->pbias_enabled == 1) {
}
}
- if (mmc_slot(host).after_set_reg)
- mmc_slot(host).after_set_reg(dev, slot, power_on, vdd);
+ if (mmc_pdata(host)->after_set_reg)
+ mmc_pdata(host)->after_set_reg(dev, power_on, vdd);
error_set_power:
return ret;
} else {
host->vcc = reg;
ocr_value = mmc_regulator_get_ocrmask(reg);
- if (!mmc_slot(host).ocr_mask) {
- mmc_slot(host).ocr_mask = ocr_value;
+ if (!mmc_pdata(host)->ocr_mask) {
+ mmc_pdata(host)->ocr_mask = ocr_value;
} else {
- if (!(mmc_slot(host).ocr_mask & ocr_value)) {
+ if (!(mmc_pdata(host)->ocr_mask & ocr_value)) {
dev_err(host->dev, "ocrmask %x is not supported\n",
- mmc_slot(host).ocr_mask);
- mmc_slot(host).ocr_mask = 0;
+ mmc_pdata(host)->ocr_mask);
+ mmc_pdata(host)->ocr_mask = 0;
return -EINVAL;
}
}
}
- mmc_slot(host).set_power = omap_hsmmc_set_power;
+ mmc_pdata(host)->set_power = omap_hsmmc_set_power;
/* Allow an aux regulator */
reg = devm_regulator_get_optional(host->dev, "vmmc_aux");
host->pbias = IS_ERR(reg) ? NULL : reg;
/* For eMMC do not power off when not in sleep state */
- if (mmc_slot(host).no_regulator_off_init)
+ if (mmc_pdata(host)->no_regulator_off_init)
return 0;
/*
* To disable boot_on regulator, enable regulator
*/
if ((host->vcc && regulator_is_enabled(host->vcc) > 0) ||
(host->vcc_aux && regulator_is_enabled(host->vcc_aux))) {
- int vdd = ffs(mmc_slot(host).ocr_mask) - 1;
+ int vdd = ffs(mmc_pdata(host)->ocr_mask) - 1;
- mmc_slot(host).set_power(host->dev, host->slot_id, 1, vdd);
- mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+ mmc_pdata(host)->set_power(host->dev, 1, vdd);
+ mmc_pdata(host)->set_power(host->dev, 0, 0);
}
return 0;
static void omap_hsmmc_reg_put(struct omap_hsmmc_host *host)
{
- mmc_slot(host).set_power = NULL;
+ mmc_pdata(host)->set_power = NULL;
}
static inline int omap_hsmmc_have_reg(void)
#endif
-static int omap_hsmmc_gpio_init(struct omap_mmc_platform_data *pdata)
+static int omap_hsmmc_gpio_init(struct omap_hsmmc_host *host,
+ struct omap_hsmmc_platform_data *pdata)
{
int ret;
- if (gpio_is_valid(pdata->slots[0].switch_pin)) {
- if (pdata->slots[0].cover)
- pdata->slots[0].get_cover_state =
- omap_hsmmc_get_cover_state;
+ if (gpio_is_valid(pdata->switch_pin)) {
+ if (pdata->cover)
+ host->get_cover_state =
+ omap_hsmmc_get_cover_state;
else
- pdata->slots[0].card_detect = omap_hsmmc_card_detect;
- pdata->slots[0].card_detect_irq =
- gpio_to_irq(pdata->slots[0].switch_pin);
- ret = gpio_request(pdata->slots[0].switch_pin, "mmc_cd");
+ host->card_detect = omap_hsmmc_card_detect;
+ host->card_detect_irq =
+ gpio_to_irq(pdata->switch_pin);
+ ret = gpio_request(pdata->switch_pin, "mmc_cd");
if (ret)
return ret;
- ret = gpio_direction_input(pdata->slots[0].switch_pin);
+ ret = gpio_direction_input(pdata->switch_pin);
if (ret)
goto err_free_sp;
- } else
- pdata->slots[0].switch_pin = -EINVAL;
+ } else {
+ pdata->switch_pin = -EINVAL;
+ }
- if (gpio_is_valid(pdata->slots[0].gpio_wp)) {
- pdata->slots[0].get_ro = omap_hsmmc_get_wp;
- ret = gpio_request(pdata->slots[0].gpio_wp, "mmc_wp");
+ if (gpio_is_valid(pdata->gpio_wp)) {
+ host->get_ro = omap_hsmmc_get_wp;
+ ret = gpio_request(pdata->gpio_wp, "mmc_wp");
if (ret)
goto err_free_cd;
- ret = gpio_direction_input(pdata->slots[0].gpio_wp);
+ ret = gpio_direction_input(pdata->gpio_wp);
if (ret)
goto err_free_wp;
- } else
- pdata->slots[0].gpio_wp = -EINVAL;
+ } else {
+ pdata->gpio_wp = -EINVAL;
+ }
return 0;
err_free_wp:
- gpio_free(pdata->slots[0].gpio_wp);
+ gpio_free(pdata->gpio_wp);
err_free_cd:
- if (gpio_is_valid(pdata->slots[0].switch_pin))
+ if (gpio_is_valid(pdata->switch_pin))
err_free_sp:
- gpio_free(pdata->slots[0].switch_pin);
+ gpio_free(pdata->switch_pin);
return ret;
}
-static void omap_hsmmc_gpio_free(struct omap_mmc_platform_data *pdata)
+static void omap_hsmmc_gpio_free(struct omap_hsmmc_host *host,
+ struct omap_hsmmc_platform_data *pdata)
{
- if (gpio_is_valid(pdata->slots[0].gpio_wp))
- gpio_free(pdata->slots[0].gpio_wp);
- if (gpio_is_valid(pdata->slots[0].switch_pin))
- gpio_free(pdata->slots[0].switch_pin);
+ if (gpio_is_valid(pdata->gpio_wp))
+ gpio_free(pdata->gpio_wp);
+ if (gpio_is_valid(pdata->switch_pin))
+ gpio_free(pdata->switch_pin);
}
/*
* in capabilities register
* - MMC/SD clock coming out of controller > 25MHz
*/
- if ((mmc_slot(host).features & HSMMC_HAS_HSPE_SUPPORT) &&
+ if ((mmc_pdata(host)->features & HSMMC_HAS_HSPE_SUPPORT) &&
(ios->timing != MMC_TIMING_MMC_DDR52) &&
+ (ios->timing != MMC_TIMING_UHS_DDR50) &&
((OMAP_HSMMC_READ(host->base, CAPA) & HSS) == HSS)) {
regval = OMAP_HSMMC_READ(host->base, HCTL);
if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000)
u32 con;
con = OMAP_HSMMC_READ(host->base, CON);
- if (ios->timing == MMC_TIMING_MMC_DDR52)
+ if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_UHS_DDR50)
con |= DDR; /* configure in DDR mode */
else
con &= ~DDR;
{
int r = 1;
- if (mmc_slot(host).get_cover_state)
- r = mmc_slot(host).get_cover_state(host->dev, host->slot_id);
+ if (host->get_cover_state)
+ r = host->get_cover_state(host->dev);
return r;
}
struct mmc_host *mmc = container_of(dev, struct mmc_host, class_dev);
struct omap_hsmmc_host *host = mmc_priv(mmc);
- return sprintf(buf, "%s\n", mmc_slot(host).name);
+ return sprintf(buf, "%s\n", mmc_pdata(host)->name);
}
static DEVICE_ATTR(slot_name, S_IRUGO, omap_hsmmc_show_slot_name, NULL);
* OMAP4 ES2 and greater has an updated reset logic.
* Monitor a 0->1 transition first
*/
- if (mmc_slot(host).features & HSMMC_HAS_UPDATED_RESET) {
+ if (mmc_pdata(host)->features & HSMMC_HAS_UPDATED_RESET) {
while ((!(OMAP_HSMMC_READ(host->base, SYSCTL) & bit))
&& (i++ < limit))
udelay(1);
clk_disable_unprepare(host->dbclk);
/* Turn the power off */
- ret = mmc_slot(host).set_power(host->dev, host->slot_id, 0, 0);
+ ret = mmc_pdata(host)->set_power(host->dev, 0, 0);
/* Turn the power ON with given VDD 1.8 or 3.0v */
if (!ret)
- ret = mmc_slot(host).set_power(host->dev, host->slot_id, 1,
- vdd);
+ ret = mmc_pdata(host)->set_power(host->dev, 1, vdd);
pm_runtime_get_sync(host->dev);
if (host->dbclk)
clk_prepare_enable(host->dbclk);
/* Protect the card while the cover is open */
static void omap_hsmmc_protect_card(struct omap_hsmmc_host *host)
{
- if (!mmc_slot(host).get_cover_state)
+ if (!host->get_cover_state)
return;
host->reqs_blocked = 0;
- if (mmc_slot(host).get_cover_state(host->dev, host->slot_id)) {
+ if (host->get_cover_state(host->dev)) {
if (host->protect_card) {
dev_info(host->dev, "%s: cover is closed, "
"card is now accessible\n",
static irqreturn_t omap_hsmmc_detect(int irq, void *dev_id)
{
struct omap_hsmmc_host *host = dev_id;
- struct omap_mmc_slot_data *slot = &mmc_slot(host);
int carddetect;
sysfs_notify(&host->mmc->class_dev.kobj, NULL, "cover_switch");
- if (slot->card_detect)
- carddetect = slot->card_detect(host->dev, host->slot_id);
+ if (host->card_detect)
+ carddetect = host->card_detect(host->dev);
else {
omap_hsmmc_protect_card(host);
carddetect = -ENOSYS;
if (ios->power_mode != host->power_mode) {
switch (ios->power_mode) {
case MMC_POWER_OFF:
- mmc_slot(host).set_power(host->dev, host->slot_id,
- 0, 0);
+ mmc_pdata(host)->set_power(host->dev, 0, 0);
break;
case MMC_POWER_UP:
- mmc_slot(host).set_power(host->dev, host->slot_id,
- 1, ios->vdd);
+ mmc_pdata(host)->set_power(host->dev, 1, ios->vdd);
break;
case MMC_POWER_ON:
do_send_init_stream = 1;
{
struct omap_hsmmc_host *host = mmc_priv(mmc);
- if (!mmc_slot(host).card_detect)
+ if (!host->card_detect)
return -ENOSYS;
- return mmc_slot(host).card_detect(host->dev, host->slot_id);
+ return host->card_detect(host->dev);
}
static int omap_hsmmc_get_ro(struct mmc_host *mmc)
{
struct omap_hsmmc_host *host = mmc_priv(mmc);
- if (!mmc_slot(host).get_ro)
+ if (!host->get_ro)
return -ENOSYS;
- return mmc_slot(host).get_ro(host->dev, 0);
+ return host->get_ro(host->dev);
}
static void omap_hsmmc_init_card(struct mmc_host *mmc, struct mmc_card *card)
{
struct omap_hsmmc_host *host = mmc_priv(mmc);
- if (mmc_slot(host).init_card)
- mmc_slot(host).init_card(card);
+ if (mmc_pdata(host)->init_card)
+ mmc_pdata(host)->init_card(card);
}
static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
};
MODULE_DEVICE_TABLE(of, omap_mmc_of_match);
-static struct omap_mmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
+static struct omap_hsmmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
{
- struct omap_mmc_platform_data *pdata;
+ struct omap_hsmmc_platform_data *pdata;
struct device_node *np = dev->of_node;
u32 bus_width, max_freq;
int cd_gpio, wp_gpio;
if (of_find_property(np, "ti,dual-volt", NULL))
pdata->controller_flags |= OMAP_HSMMC_SUPPORTS_DUAL_VOLT;
- /* This driver only supports 1 slot */
- pdata->nr_slots = 1;
- pdata->slots[0].switch_pin = cd_gpio;
- pdata->slots[0].gpio_wp = wp_gpio;
+ pdata->switch_pin = cd_gpio;
+ pdata->gpio_wp = wp_gpio;
if (of_find_property(np, "ti,non-removable", NULL)) {
- pdata->slots[0].nonremovable = true;
- pdata->slots[0].no_regulator_off_init = true;
+ pdata->nonremovable = true;
+ pdata->no_regulator_off_init = true;
}
of_property_read_u32(np, "bus-width", &bus_width);
if (bus_width == 4)
- pdata->slots[0].caps |= MMC_CAP_4_BIT_DATA;
+ pdata->caps |= MMC_CAP_4_BIT_DATA;
else if (bus_width == 8)
- pdata->slots[0].caps |= MMC_CAP_8_BIT_DATA;
+ pdata->caps |= MMC_CAP_8_BIT_DATA;
if (of_find_property(np, "ti,needs-special-reset", NULL))
- pdata->slots[0].features |= HSMMC_HAS_UPDATED_RESET;
+ pdata->features |= HSMMC_HAS_UPDATED_RESET;
if (!of_property_read_u32(np, "max-frequency", &max_freq))
pdata->max_freq = max_freq;
if (of_find_property(np, "ti,needs-special-hs-handling", NULL))
- pdata->slots[0].features |= HSMMC_HAS_HSPE_SUPPORT;
+ pdata->features |= HSMMC_HAS_HSPE_SUPPORT;
if (of_find_property(np, "keep-power-in-suspend", NULL))
- pdata->slots[0].pm_caps |= MMC_PM_KEEP_POWER;
+ pdata->pm_caps |= MMC_PM_KEEP_POWER;
if (of_find_property(np, "enable-sdio-wakeup", NULL))
- pdata->slots[0].pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
+ pdata->pm_caps |= MMC_PM_WAKE_SDIO_IRQ;
return pdata;
}
#else
-static inline struct omap_mmc_platform_data
+static inline struct omap_hsmmc_platform_data
*of_get_hsmmc_pdata(struct device *dev)
{
return ERR_PTR(-EINVAL);
static int omap_hsmmc_probe(struct platform_device *pdev)
{
- struct omap_mmc_platform_data *pdata = pdev->dev.platform_data;
+ struct omap_hsmmc_platform_data *pdata = pdev->dev.platform_data;
struct mmc_host *mmc;
struct omap_hsmmc_host *host = NULL;
struct resource *res;
return -ENXIO;
}
- if (pdata->nr_slots == 0) {
- dev_err(&pdev->dev, "No Slots\n");
- return -ENXIO;
- }
-
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_irq(pdev, 0);
if (res == NULL || irq < 0)
if (IS_ERR(base))
return PTR_ERR(base);
- ret = omap_hsmmc_gpio_init(pdata);
- if (ret)
- goto err;
-
mmc = mmc_alloc_host(sizeof(struct omap_hsmmc_host), &pdev->dev);
if (!mmc) {
ret = -ENOMEM;
- goto err_alloc;
+ goto err;
}
host = mmc_priv(mmc);
host->use_dma = 1;
host->dma_ch = -1;
host->irq = irq;
- host->slot_id = 0;
host->mapbase = res->start + pdata->reg_offset;
host->base = base + pdata->reg_offset;
host->power_mode = MMC_POWER_OFF;
host->next_data.cookie = 1;
host->pbias_enabled = 0;
+ ret = omap_hsmmc_gpio_init(host, pdata);
+ if (ret)
+ goto err_gpio;
+
platform_set_drvdata(pdev, host);
if (pdev->dev.of_node)
mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_ERASE;
- mmc->caps |= mmc_slot(host).caps;
+ mmc->caps |= mmc_pdata(host)->caps;
if (mmc->caps & MMC_CAP_8_BIT_DATA)
mmc->caps |= MMC_CAP_4_BIT_DATA;
- if (mmc_slot(host).nonremovable)
+ if (mmc_pdata(host)->nonremovable)
mmc->caps |= MMC_CAP_NONREMOVABLE;
- mmc->pm_caps = mmc_slot(host).pm_caps;
+ mmc->pm_caps = mmc_pdata(host)->pm_caps;
omap_hsmmc_conf_bus_power(host);
goto err_irq;
}
- if (pdata->init != NULL) {
- if (pdata->init(&pdev->dev) != 0) {
- dev_err(mmc_dev(host->mmc),
- "Unable to configure MMC IRQs\n");
- goto err_irq;
- }
- }
-
- if (omap_hsmmc_have_reg() && !mmc_slot(host).set_power) {
+ if (omap_hsmmc_have_reg() && !mmc_pdata(host)->set_power) {
ret = omap_hsmmc_reg_get(host);
if (ret)
- goto err_reg;
+ goto err_irq;
host->use_reg = 1;
}
- mmc->ocr_avail = mmc_slot(host).ocr_mask;
+ mmc->ocr_avail = mmc_pdata(host)->ocr_mask;
/* Request IRQ for card detect */
- if ((mmc_slot(host).card_detect_irq)) {
+ if (host->card_detect_irq) {
ret = devm_request_threaded_irq(&pdev->dev,
- mmc_slot(host).card_detect_irq,
+ host->card_detect_irq,
NULL, omap_hsmmc_detect,
IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
mmc_hostname(mmc), host);
"Unable to grab MMC CD IRQ\n");
goto err_irq_cd;
}
- pdata->suspend = omap_hsmmc_suspend_cdirq;
- pdata->resume = omap_hsmmc_resume_cdirq;
+ host->suspend = omap_hsmmc_suspend_cdirq;
+ host->resume = omap_hsmmc_resume_cdirq;
}
omap_hsmmc_disable_irq(host);
mmc_add_host(mmc);
- if (mmc_slot(host).name != NULL) {
+ if (mmc_pdata(host)->name != NULL) {
ret = device_create_file(&mmc->class_dev, &dev_attr_slot_name);
if (ret < 0)
goto err_slot_name;
}
- if (mmc_slot(host).card_detect_irq && mmc_slot(host).get_cover_state) {
+ if (host->card_detect_irq && host->get_cover_state) {
ret = device_create_file(&mmc->class_dev,
&dev_attr_cover_switch);
if (ret < 0)
err_irq_cd:
if (host->use_reg)
omap_hsmmc_reg_put(host);
-err_reg:
- if (host->pdata->cleanup)
- host->pdata->cleanup(&pdev->dev);
err_irq:
if (host->tx_chan)
dma_release_channel(host->tx_chan);
if (host->dbclk)
clk_disable_unprepare(host->dbclk);
err1:
+ omap_hsmmc_gpio_free(host, pdata);
+err_gpio:
mmc_free_host(mmc);
-err_alloc:
- omap_hsmmc_gpio_free(pdata);
err:
return ret;
}
mmc_remove_host(host->mmc);
if (host->use_reg)
omap_hsmmc_reg_put(host);
- if (host->pdata->cleanup)
- host->pdata->cleanup(&pdev->dev);
if (host->tx_chan)
dma_release_channel(host->tx_chan);
if (host->dbclk)
clk_disable_unprepare(host->dbclk);
- omap_hsmmc_gpio_free(host->pdata);
+ omap_hsmmc_gpio_free(host, host->pdata);
mmc_free_host(host->mmc);
return 0;
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- if (host->pdata->suspend)
- return host->pdata->suspend(dev, host->slot_id);
+ if (host->suspend)
+ return host->suspend(dev);
return 0;
}
{
struct omap_hsmmc_host *host = dev_get_drvdata(dev);
- if (host->pdata->resume)
- host->pdata->resume(dev, host->slot_id);
+ if (host->resume)
+ host->resume(dev);
}
const struct sdhci_acpi_slot *slot;
struct platform_device *pdev;
bool use_runtime_pm;
+ bool dma_setup;
};
static inline bool sdhci_acpi_flag(struct sdhci_acpi_host *c, unsigned int flag)
static int sdhci_acpi_enable_dma(struct sdhci_host *host)
{
- return 0;
+ struct sdhci_acpi_host *c = sdhci_priv(host);
+ struct device *dev = &c->pdev->dev;
+ int err = -1;
+
+ if (c->dma_setup)
+ return 0;
+
+ if (host->flags & SDHCI_USE_64_BIT_DMA) {
+ if (host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA) {
+ host->flags &= ~SDHCI_USE_64_BIT_DMA;
+ } else {
+ err = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
+ if (err)
+ dev_warn(dev, "Failed to set 64-bit DMA mask\n");
+ }
+ }
+
+ if (err)
+ err = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
+
+ c->dma_setup = !err;
+
+ return err;
}
static void sdhci_acpi_int_hw_reset(struct sdhci_host *host)
static const struct sdhci_acpi_slot sdhci_acpi_slot_int_emmc = {
.chip = &sdhci_acpi_chip_int,
.caps = MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE |
- MMC_CAP_HW_RESET | MMC_CAP_1_8V_DDR,
+ MMC_CAP_HW_RESET | MMC_CAP_1_8V_DDR |
+ MMC_CAP_BUS_WIDTH_TEST | MMC_CAP_WAIT_WHILE_BUSY,
.caps2 = MMC_CAP2_HC_ERASE_SZ,
.flags = SDHCI_ACPI_RUNTIME_PM,
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN | SDHCI_QUIRK2_STOP_WITH_TC,
.probe_slot = sdhci_acpi_emmc_probe_slot,
};
static const struct sdhci_acpi_slot sdhci_acpi_slot_int_sdio = {
- .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION,
+ .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+ SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_HOST_OFF_CARD_ON,
- .caps = MMC_CAP_NONREMOVABLE | MMC_CAP_POWER_OFF_CARD,
+ .caps = MMC_CAP_NONREMOVABLE | MMC_CAP_POWER_OFF_CARD |
+ MMC_CAP_BUS_WIDTH_TEST | MMC_CAP_WAIT_WHILE_BUSY,
.flags = SDHCI_ACPI_RUNTIME_PM,
.pm_caps = MMC_PM_KEEP_POWER,
.probe_slot = sdhci_acpi_sdio_probe_slot,
static const struct sdhci_acpi_slot sdhci_acpi_slot_int_sd = {
.flags = SDHCI_ACPI_SD_CD | SDHCI_ACPI_SD_CD_OVERRIDE_LEVEL |
SDHCI_ACPI_RUNTIME_PM,
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON |
SDHCI_QUIRK2_STOP_WITH_TC,
+ .caps = MMC_CAP_BUS_WIDTH_TEST | MMC_CAP_WAIT_WHILE_BUSY,
.probe_slot = sdhci_acpi_sd_probe_slot,
};
goto err_free;
}
- if (!dev->dma_mask) {
- u64 dma_mask;
-
- if (sdhci_readl(host, SDHCI_CAPABILITIES) & SDHCI_CAN_64BIT) {
- /* 64-bit DMA is not supported at present */
- dma_mask = DMA_BIT_MASK(32);
- } else {
- dma_mask = DMA_BIT_MASK(32);
- }
-
- err = dma_coerce_mask_and_coherent(dev, dma_mask);
- if (err)
- goto err_free;
- }
-
if (c->slot) {
if (c->slot->probe_slot) {
err = c->slot->probe_slot(pdev, hid, uid);
/* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
#define ESDHC_TUNING_START_TAP 0x1
-#define ESDHC_TUNING_BLOCK_PATTERN_LEN 64
-
/* pinctrl state */
#define ESDHC_PINCTRL_STATE_100MHZ "state_100mhz"
#define ESDHC_PINCTRL_STATE_200MHZ "state_200mhz"
/* FIXME: delay a bit for card to be ready for next tuning due to errors */
mdelay(1);
- /* This is balanced by the runtime put in sdhci_tasklet_finish */
- pm_runtime_get_sync(host->mmc->parent);
reg = readl(host->ioaddr + ESDHC_MIX_CTRL);
reg |= ESDHC_MIX_CTRL_EXE_TUNE | ESDHC_MIX_CTRL_SMPCLK_SEL |
ESDHC_MIX_CTRL_FBCLK_SEL;
val, readl(host->ioaddr + ESDHC_TUNE_CTRL_STATUS));
}
-static void esdhc_request_done(struct mmc_request *mrq)
-{
- complete(&mrq->completion);
-}
-
-static int esdhc_send_tuning_cmd(struct sdhci_host *host, u32 opcode,
- struct scatterlist *sg)
-{
- struct mmc_command cmd = {0};
- struct mmc_request mrq = {NULL};
- struct mmc_data data = {0};
-
- cmd.opcode = opcode;
- cmd.arg = 0;
- cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
-
- data.blksz = ESDHC_TUNING_BLOCK_PATTERN_LEN;
- data.blocks = 1;
- data.flags = MMC_DATA_READ;
- data.sg = sg;
- data.sg_len = 1;
-
- mrq.cmd = &cmd;
- mrq.cmd->mrq = &mrq;
- mrq.data = &data;
- mrq.data->mrq = &mrq;
- mrq.cmd->data = mrq.data;
-
- mrq.done = esdhc_request_done;
- init_completion(&(mrq.completion));
-
- spin_lock_irq(&host->lock);
- host->mrq = &mrq;
-
- sdhci_send_command(host, mrq.cmd);
-
- spin_unlock_irq(&host->lock);
-
- wait_for_completion(&mrq.completion);
-
- if (cmd.error)
- return cmd.error;
- if (data.error)
- return data.error;
-
- return 0;
-}
-
static void esdhc_post_tuning(struct sdhci_host *host)
{
u32 reg;
static int esdhc_executing_tuning(struct sdhci_host *host, u32 opcode)
{
- struct scatterlist sg;
- char *tuning_pattern;
int min, max, avg, ret;
- tuning_pattern = kmalloc(ESDHC_TUNING_BLOCK_PATTERN_LEN, GFP_KERNEL);
- if (!tuning_pattern)
- return -ENOMEM;
-
- sg_init_one(&sg, tuning_pattern, ESDHC_TUNING_BLOCK_PATTERN_LEN);
-
/* find the mininum delay first which can pass tuning */
min = ESDHC_TUNE_CTRL_MIN;
while (min < ESDHC_TUNE_CTRL_MAX) {
esdhc_prepare_tuning(host, min);
- if (!esdhc_send_tuning_cmd(host, opcode, &sg))
+ if (!mmc_send_tuning(host->mmc))
break;
min += ESDHC_TUNE_CTRL_STEP;
}
max = min + ESDHC_TUNE_CTRL_STEP;
while (max < ESDHC_TUNE_CTRL_MAX) {
esdhc_prepare_tuning(host, max);
- if (esdhc_send_tuning_cmd(host, opcode, &sg)) {
+ if (mmc_send_tuning(host->mmc)) {
max -= ESDHC_TUNE_CTRL_STEP;
break;
}
/* use average delay to get the best timing */
avg = (min + max) / 2;
esdhc_prepare_tuning(host, avg);
- ret = esdhc_send_tuning_cmd(host, opcode, &sg);
+ ret = mmc_send_tuning(host->mmc);
esdhc_post_tuning(host);
- kfree(tuning_pattern);
-
dev_dbg(mmc_dev(host->mmc), "tunning %s at 0x%x ret %d\n",
ret ? "failed" : "passed", avg, ret);
imx_data->pins_default = pinctrl_lookup_state(imx_data->pinctrl,
PINCTRL_STATE_DEFAULT);
- if (IS_ERR(imx_data->pins_default)) {
- err = PTR_ERR(imx_data->pins_default);
- dev_err(mmc_dev(host->mmc), "could not get default state\n");
- goto disable_clk;
- }
+ if (IS_ERR(imx_data->pins_default))
+ dev_warn(mmc_dev(host->mmc), "could not get default state\n");
host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;
}
/* sdr50 and sdr104 needs work on 1.8v signal voltage */
- if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data)) {
+ if ((boarddata->support_vsel) && esdhc_is_usdhc(imx_data) &&
+ !IS_ERR(imx_data->pins_default)) {
imx_data->pins_100mhz = pinctrl_lookup_state(imx_data->pinctrl,
ESDHC_PINCTRL_STATE_100MHZ);
imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
static int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode)
{
int tuning_seq_cnt = 3;
- u8 phase, *data_buf, tuned_phases[16], tuned_phase_cnt = 0;
- const u8 *tuning_block_pattern = tuning_blk_pattern_4bit;
- int size = sizeof(tuning_blk_pattern_4bit);
+ u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
int rc;
struct mmc_host *mmc = host->mmc;
struct mmc_ios ios = host->mmc->ios;
(ios.timing == MMC_TIMING_UHS_SDR104)))
return 0;
- if ((opcode == MMC_SEND_TUNING_BLOCK_HS200) &&
- (mmc->ios.bus_width == MMC_BUS_WIDTH_8)) {
- tuning_block_pattern = tuning_blk_pattern_8bit;
- size = sizeof(tuning_blk_pattern_8bit);
- }
-
- data_buf = kmalloc(size, GFP_KERNEL);
- if (!data_buf)
- return -ENOMEM;
-
retry:
/* First of all reset the tuning block */
rc = msm_init_cm_dll(host);
if (rc)
- goto out;
+ return rc;
phase = 0;
do {
- struct mmc_command cmd = { 0 };
- struct mmc_data data = { 0 };
- struct mmc_request mrq = {
- .cmd = &cmd,
- .data = &data
- };
- struct scatterlist sg;
-
/* Set the phase in delay line hw block */
rc = msm_config_cm_dll_phase(host, phase);
if (rc)
- goto out;
+ return rc;
- cmd.opcode = opcode;
- cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
-
- data.blksz = size;
- data.blocks = 1;
- data.flags = MMC_DATA_READ;
- data.timeout_ns = NSEC_PER_SEC; /* 1 second */
-
- data.sg = &sg;
- data.sg_len = 1;
- sg_init_one(&sg, data_buf, size);
- memset(data_buf, 0, size);
- mmc_wait_for_req(mmc, &mrq);
-
- if (!cmd.error && !data.error &&
- !memcmp(data_buf, tuning_block_pattern, size)) {
+ rc = mmc_send_tuning(mmc);
+ if (!rc) {
/* Tuning is successful at this tuning point */
tuned_phases[tuned_phase_cnt++] = phase;
dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
rc = msm_find_most_appropriate_phase(host, tuned_phases,
tuned_phase_cnt);
if (rc < 0)
- goto out;
+ return rc;
else
phase = rc;
*/
rc = msm_config_cm_dll_phase(host, phase);
if (rc)
- goto out;
+ return rc;
dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
mmc_hostname(mmc), phase);
} else {
rc = -EIO;
}
-out:
- kfree(data_buf);
return rc;
}
host = sdhci_pltfm_init(pdev, &sdhci_arasan_pdata, 0);
if (IS_ERR(host)) {
ret = PTR_ERR(host);
- dev_err(&pdev->dev, "platform init failed (%u)\n", ret);
goto clk_disable_all;
}
pltfm_host->clk = clk_xin;
ret = sdhci_add_host(host);
- if (ret) {
- dev_err(&pdev->dev, "platform register failed (%u)\n", ret);
+ if (ret)
goto err_pltfm_free;
- }
return 0;
return;
scratch_32 &= ~((1 << 21) | (1 << 30));
- /* Set RTD3 function disabled */
- scratch_32 |= ((1 << 29) | (1 << 28));
pci_write_config_dword(chip->pdev, O2_SD_FUNC_REG3, scratch_32);
/* Set L1 Entrance Timer */
static int byt_emmc_probe_slot(struct sdhci_pci_slot *slot)
{
slot->host->mmc->caps |= MMC_CAP_8_BIT_DATA | MMC_CAP_NONREMOVABLE |
- MMC_CAP_HW_RESET | MMC_CAP_1_8V_DDR;
+ MMC_CAP_HW_RESET | MMC_CAP_1_8V_DDR |
+ MMC_CAP_BUS_WIDTH_TEST |
+ MMC_CAP_WAIT_WHILE_BUSY;
slot->host->mmc->caps2 |= MMC_CAP2_HC_ERASE_SZ;
slot->hw_reset = sdhci_pci_int_hw_reset;
if (slot->chip->pdev->device == PCI_DEVICE_ID_INTEL_BSW_EMMC)
static int byt_sdio_probe_slot(struct sdhci_pci_slot *slot)
{
- slot->host->mmc->caps |= MMC_CAP_POWER_OFF_CARD | MMC_CAP_NONREMOVABLE;
+ slot->host->mmc->caps |= MMC_CAP_POWER_OFF_CARD | MMC_CAP_NONREMOVABLE |
+ MMC_CAP_BUS_WIDTH_TEST |
+ MMC_CAP_WAIT_WHILE_BUSY;
return 0;
}
static int byt_sd_probe_slot(struct sdhci_pci_slot *slot)
{
+ slot->host->mmc->caps |= MMC_CAP_BUS_WIDTH_TEST |
+ MMC_CAP_WAIT_WHILE_BUSY;
slot->cd_con_id = NULL;
slot->cd_idx = 0;
slot->cd_override_level = true;
static const struct sdhci_pci_fixes sdhci_intel_byt_emmc = {
.allow_runtime_pm = true,
.probe_slot = byt_emmc_probe_slot,
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
SDHCI_QUIRK2_STOP_WITH_TC,
};
static const struct sdhci_pci_fixes sdhci_intel_byt_sdio = {
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_HOST_OFF_CARD_ON |
SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
.allow_runtime_pm = true,
};
static const struct sdhci_pci_fixes sdhci_intel_byt_sd = {
+ .quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
.quirks2 = SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON |
SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
SDHCI_QUIRK2_STOP_WITH_TC,
.probe_slot = rtsx_probe_slot,
};
+static int amd_probe(struct sdhci_pci_chip *chip)
+{
+ struct pci_dev *smbus_dev;
+
+ smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
+ PCI_DEVICE_ID_AMD_HUDSON2_SMBUS, NULL);
+
+ if (smbus_dev && (smbus_dev->revision < 0x51)) {
+ chip->quirks2 |= SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD;
+ chip->quirks2 |= SDHCI_QUIRK2_BROKEN_HS200;
+ }
+
+ return 0;
+}
+
+static const struct sdhci_pci_fixes sdhci_amd = {
+ .probe = amd_probe,
+};
+
static const struct pci_device_id pci_ids[] = {
{
.vendor = PCI_VENDOR_ID_RICOH,
.subdevice = PCI_ANY_ID,
.driver_data = (kernel_ulong_t)&sdhci_o2,
},
-
+ {
+ .vendor = PCI_VENDOR_ID_AMD,
+ .device = PCI_ANY_ID,
+ .class = PCI_CLASS_SYSTEM_SDHCI << 8,
+ .class_mask = 0xFFFF00,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .driver_data = (kernel_ulong_t)&sdhci_amd,
+ },
{ /* Generic SD host controller */
PCI_DEVICE_CLASS((PCI_CLASS_SYSTEM_SDHCI << 8), 0xFFFF00)
},
{
struct sdhci_pci_slot *slot;
struct pci_dev *pdev;
- int ret;
+ int ret = -1;
slot = sdhci_priv(host);
pdev = slot->chip->pdev;
"doesn't fully claim to support it.\n");
}
- ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
+ if (host->flags & SDHCI_USE_64_BIT_DMA) {
+ if (host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA) {
+ host->flags &= ~SDHCI_USE_64_BIT_DMA;
+ } else {
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
+ if (ret)
+ dev_warn(&pdev->dev, "Failed to set 64-bit DMA mask\n");
+ }
+ }
+ if (ret)
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (ret)
return ret;
struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data;
struct device *dev = &pdev->dev;
struct sdhci_host *host = NULL;
- struct sdhci_pxa *pxa = NULL;
const struct of_device_id *match;
int ret;
struct clk *clk;
- pxa = kzalloc(sizeof(struct sdhci_pxa), GFP_KERNEL);
- if (!pxa)
- return -ENOMEM;
-
host = sdhci_pltfm_init(pdev, NULL, 0);
- if (IS_ERR(host)) {
- kfree(pxa);
+ if (IS_ERR(host))
return PTR_ERR(host);
- }
+
pltfm_host = sdhci_priv(host);
- pltfm_host->priv = pxa;
+ pltfm_host->priv = NULL;
clk = clk_get(dev, "PXA-SDHCLK");
if (IS_ERR(clk)) {
clk_put(clk);
err_clk_get:
sdhci_pltfm_free(pdev);
- kfree(pxa);
return ret;
}
{
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
- struct sdhci_pxa *pxa = pltfm_host->priv;
sdhci_remove_host(host, 1);
clk_disable_unprepare(pltfm_host->clk);
clk_put(pltfm_host->clk);
sdhci_pltfm_free(pdev);
- kfree(pxa);
return 0;
}
#define SDCE_MISC_INT (1<<2)
#define SDCE_MISC_INT_EN (1<<1)
+struct sdhci_pxa {
+ struct clk *clk_core;
+ struct clk *clk_io;
+ u8 power_mode;
+};
+
/*
* These registers are relative to the second register region, for the
* MBus bridge.
case MMC_TIMING_UHS_SDR104:
ctrl_2 |= SDHCI_CTRL_UHS_SDR104 | SDHCI_CTRL_VDD_180;
break;
+ case MMC_TIMING_MMC_DDR52:
case MMC_TIMING_UHS_DDR50:
ctrl_2 |= SDHCI_CTRL_UHS_DDR50 | SDHCI_CTRL_VDD_180;
break;
struct sdhci_host *host = NULL;
struct sdhci_pxa *pxa = NULL;
const struct of_device_id *match;
-
int ret;
- struct clk *clk;
pxa = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_pxa), GFP_KERNEL);
if (!pxa)
pltfm_host = sdhci_priv(host);
pltfm_host->priv = pxa;
- clk = devm_clk_get(dev, NULL);
- if (IS_ERR(clk)) {
+ pxa->clk_io = devm_clk_get(dev, "io");
+ if (IS_ERR(pxa->clk_io))
+ pxa->clk_io = devm_clk_get(dev, NULL);
+ if (IS_ERR(pxa->clk_io)) {
dev_err(dev, "failed to get io clock\n");
- ret = PTR_ERR(clk);
+ ret = PTR_ERR(pxa->clk_io);
goto err_clk_get;
}
- pltfm_host->clk = clk;
- clk_prepare_enable(clk);
+ pltfm_host->clk = pxa->clk_io;
+ clk_prepare_enable(pxa->clk_io);
+
+ pxa->clk_core = devm_clk_get(dev, "core");
+ if (!IS_ERR(pxa->clk_core))
+ clk_prepare_enable(pxa->clk_core);
/* enable 1/8V DDR capable */
host->mmc->caps |= MMC_CAP_1_8V_DDR;
pm_runtime_disable(&pdev->dev);
err_of_parse:
err_cd_req:
- clk_disable_unprepare(clk);
+ clk_disable_unprepare(pxa->clk_io);
+ if (!IS_ERR(pxa->clk_core))
+ clk_disable_unprepare(pxa->clk_core);
err_clk_get:
err_mbus_win:
sdhci_pltfm_free(pdev);
{
struct sdhci_host *host = platform_get_drvdata(pdev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
pm_runtime_get_sync(&pdev->dev);
sdhci_remove_host(host, 1);
pm_runtime_disable(&pdev->dev);
- clk_disable_unprepare(pltfm_host->clk);
+ clk_disable_unprepare(pxa->clk_io);
+ if (!IS_ERR(pxa->clk_core))
+ clk_disable_unprepare(pxa->clk_core);
sdhci_pltfm_free(pdev);
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
unsigned long flags;
- if (pltfm_host->clk) {
- spin_lock_irqsave(&host->lock, flags);
- host->runtime_suspended = true;
- spin_unlock_irqrestore(&host->lock, flags);
+ spin_lock_irqsave(&host->lock, flags);
+ host->runtime_suspended = true;
+ spin_unlock_irqrestore(&host->lock, flags);
- clk_disable_unprepare(pltfm_host->clk);
- }
+ clk_disable_unprepare(pxa->clk_io);
+ if (!IS_ERR(pxa->clk_core))
+ clk_disable_unprepare(pxa->clk_core);
return 0;
}
{
struct sdhci_host *host = dev_get_drvdata(dev);
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_pxa *pxa = pltfm_host->priv;
unsigned long flags;
- if (pltfm_host->clk) {
- clk_prepare_enable(pltfm_host->clk);
+ clk_prepare_enable(pxa->clk_io);
+ if (!IS_ERR(pxa->clk_core))
+ clk_prepare_enable(pxa->clk_core);
- spin_lock_irqsave(&host->lock, flags);
- host->runtime_suspended = false;
- spin_unlock_irqrestore(&host->lock, flags);
- }
+ spin_lock_irqsave(&host->lock, flags);
+ host->runtime_suspended = false;
+ spin_unlock_irqrestore(&host->lock, flags);
return 0;
}
struct device *dev = &ourhost->pdev->dev;
unsigned long timeout;
u16 clk = 0;
+ int ret;
host->mmc->actual_clock = 0;
sdhci_s3c_set_clock(host, clock);
- clk_set_rate(ourhost->clk_bus[ourhost->cur_clk], clock);
+ ret = clk_set_rate(ourhost->clk_bus[ourhost->cur_clk], clock);
+ if (ret != 0) {
+ dev_err(dev, "%s: failed to set clock rate %uHz\n",
+ mmc_hostname(host->mmc), clock);
+ return;
+ }
clk = SDHCI_CLOCK_INT_EN;
sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
#define MAX_TUNING_LOOP 40
-#define ADMA_SIZE ((128 * 2 + 1) * 4)
-
static unsigned int debug_quirks = 0;
static unsigned int debug_quirks2;
pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n",
sdhci_readw(host, SDHCI_HOST_CONTROL2));
- if (host->flags & SDHCI_USE_ADMA)
- pr_debug(DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
- readl(host->ioaddr + SDHCI_ADMA_ERROR),
- readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
+ if (host->flags & SDHCI_USE_ADMA) {
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ pr_debug(DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x%08x\n",
+ readl(host->ioaddr + SDHCI_ADMA_ERROR),
+ readl(host->ioaddr + SDHCI_ADMA_ADDRESS_HI),
+ readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
+ else
+ pr_debug(DRIVER_NAME ": ADMA Err: 0x%08x | ADMA Ptr: 0x%08x\n",
+ readl(host->ioaddr + SDHCI_ADMA_ERROR),
+ readl(host->ioaddr + SDHCI_ADMA_ADDRESS));
+ }
pr_debug(DRIVER_NAME ": ===========================================\n");
}
local_irq_restore(*flags);
}
-static void sdhci_set_adma_desc(u8 *desc, u32 addr, int len, unsigned cmd)
+static void sdhci_adma_write_desc(struct sdhci_host *host, void *desc,
+ dma_addr_t addr, int len, unsigned cmd)
{
- __le32 *dataddr = (__le32 __force *)(desc + 4);
- __le16 *cmdlen = (__le16 __force *)desc;
+ struct sdhci_adma2_64_desc *dma_desc = desc;
+
+ /* 32-bit and 64-bit descriptors have these members in same position */
+ dma_desc->cmd = cpu_to_le16(cmd);
+ dma_desc->len = cpu_to_le16(len);
+ dma_desc->addr_lo = cpu_to_le32((u32)addr);
- /* SDHCI specification says ADMA descriptors should be 4 byte
- * aligned, so using 16 or 32bit operations should be safe. */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ dma_desc->addr_hi = cpu_to_le32((u64)addr >> 32);
+}
- cmdlen[0] = cpu_to_le16(cmd);
- cmdlen[1] = cpu_to_le16(len);
+static void sdhci_adma_mark_end(void *desc)
+{
+ struct sdhci_adma2_64_desc *dma_desc = desc;
- dataddr[0] = cpu_to_le32(addr);
+ /* 32-bit and 64-bit descriptors have 'cmd' in same position */
+ dma_desc->cmd |= cpu_to_le16(ADMA2_END);
}
static int sdhci_adma_table_pre(struct sdhci_host *host,
{
int direction;
- u8 *desc;
- u8 *align;
+ void *desc;
+ void *align;
dma_addr_t addr;
dma_addr_t align_addr;
int len, offset;
direction = DMA_TO_DEVICE;
host->align_addr = dma_map_single(mmc_dev(host->mmc),
- host->align_buffer, 128 * 4, direction);
+ host->align_buffer, host->align_buffer_sz, direction);
if (dma_mapping_error(mmc_dev(host->mmc), host->align_addr))
goto fail;
- BUG_ON(host->align_addr & 0x3);
+ BUG_ON(host->align_addr & host->align_mask);
host->sg_count = dma_map_sg(mmc_dev(host->mmc),
data->sg, data->sg_len, direction);
if (host->sg_count == 0)
goto unmap_align;
- desc = host->adma_desc;
+ desc = host->adma_table;
align = host->align_buffer;
align_addr = host->align_addr;
* the (up to three) bytes that screw up the
* alignment.
*/
- offset = (4 - (addr & 0x3)) & 0x3;
+ offset = (host->align_sz - (addr & host->align_mask)) &
+ host->align_mask;
if (offset) {
if (data->flags & MMC_DATA_WRITE) {
buffer = sdhci_kmap_atomic(sg, &flags);
- WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
+ WARN_ON(((long)buffer & (PAGE_SIZE - 1)) >
+ (PAGE_SIZE - offset));
memcpy(align, buffer, offset);
sdhci_kunmap_atomic(buffer, &flags);
}
/* tran, valid */
- sdhci_set_adma_desc(desc, align_addr, offset, 0x21);
+ sdhci_adma_write_desc(host, desc, align_addr, offset,
+ ADMA2_TRAN_VALID);
BUG_ON(offset > 65536);
- align += 4;
- align_addr += 4;
+ align += host->align_sz;
+ align_addr += host->align_sz;
- desc += 8;
+ desc += host->desc_sz;
addr += offset;
len -= offset;
BUG_ON(len > 65536);
/* tran, valid */
- sdhci_set_adma_desc(desc, addr, len, 0x21);
- desc += 8;
+ sdhci_adma_write_desc(host, desc, addr, len, ADMA2_TRAN_VALID);
+ desc += host->desc_sz;
/*
* If this triggers then we have a calculation bug
* somewhere. :/
*/
- WARN_ON((desc - host->adma_desc) > ADMA_SIZE);
+ WARN_ON((desc - host->adma_table) >= host->adma_table_sz);
}
if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
/*
* Mark the last descriptor as the terminating descriptor
*/
- if (desc != host->adma_desc) {
- desc -= 8;
- desc[0] |= 0x2; /* end */
+ if (desc != host->adma_table) {
+ desc -= host->desc_sz;
+ sdhci_adma_mark_end(desc);
}
} else {
/*
*/
/* nop, end, valid */
- sdhci_set_adma_desc(desc, 0, 0, 0x3);
+ sdhci_adma_write_desc(host, desc, 0, 0, ADMA2_NOP_END_VALID);
}
/*
*/
if (data->flags & MMC_DATA_WRITE) {
dma_sync_single_for_device(mmc_dev(host->mmc),
- host->align_addr, 128 * 4, direction);
+ host->align_addr, host->align_buffer_sz, direction);
}
return 0;
unmap_align:
dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
- 128 * 4, direction);
+ host->align_buffer_sz, direction);
fail:
return -EINVAL;
}
struct scatterlist *sg;
int i, size;
- u8 *align;
+ void *align;
char *buffer;
unsigned long flags;
bool has_unaligned;
direction = DMA_TO_DEVICE;
dma_unmap_single(mmc_dev(host->mmc), host->align_addr,
- 128 * 4, direction);
+ host->align_buffer_sz, direction);
/* Do a quick scan of the SG list for any unaligned mappings */
has_unaligned = false;
for_each_sg(data->sg, sg, host->sg_count, i)
- if (sg_dma_address(sg) & 3) {
+ if (sg_dma_address(sg) & host->align_mask) {
has_unaligned = true;
break;
}
align = host->align_buffer;
for_each_sg(data->sg, sg, host->sg_count, i) {
- if (sg_dma_address(sg) & 0x3) {
- size = 4 - (sg_dma_address(sg) & 0x3);
+ if (sg_dma_address(sg) & host->align_mask) {
+ size = host->align_sz -
+ (sg_dma_address(sg) & host->align_mask);
buffer = sdhci_kmap_atomic(sg, &flags);
- WARN_ON(((long)buffer & PAGE_MASK) > (PAGE_SIZE - 3));
+ WARN_ON(((long)buffer & (PAGE_SIZE - 1)) >
+ (PAGE_SIZE - size));
memcpy(buffer, align, size);
sdhci_kunmap_atomic(buffer, &flags);
- align += 4;
+ align += host->align_sz;
}
}
}
} else {
sdhci_writel(host, host->adma_addr,
SDHCI_ADMA_ADDRESS);
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ sdhci_writel(host,
+ (u64)host->adma_addr >> 32,
+ SDHCI_ADMA_ADDRESS_HI);
}
} else {
int sg_cnt;
ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
ctrl &= ~SDHCI_CTRL_DMA_MASK;
if ((host->flags & SDHCI_REQ_USE_DMA) &&
- (host->flags & SDHCI_USE_ADMA))
- ctrl |= SDHCI_CTRL_ADMA32;
- else
+ (host->flags & SDHCI_USE_ADMA)) {
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ ctrl |= SDHCI_CTRL_ADMA64;
+ else
+ ctrl |= SDHCI_CTRL_ADMA32;
+ } else {
ctrl |= SDHCI_CTRL_SDMA;
+ }
sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
}
struct mmc_data *data = cmd->data;
if (data == NULL) {
+ if (host->quirks2 &
+ SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
+ sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
+ } else {
/* clear Auto CMD settings for no data CMDs */
- mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
- sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
+ mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
+ sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
+ }
return;
}
case MMC_TIMING_UHS_DDR50:
preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
break;
+ case MMC_TIMING_MMC_HS400:
+ preset = sdhci_readw(host, SDHCI_PRESET_FOR_HS400);
+ break;
default:
pr_warn("%s: Invalid UHS-I mode selected\n",
mmc_hostname(host->mmc));
else if ((timing == MMC_TIMING_UHS_DDR50) ||
(timing == MMC_TIMING_MMC_DDR52))
ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
+ else if (timing == MMC_TIMING_MMC_HS400)
+ ctrl_2 |= SDHCI_CTRL_HS400; /* Non-standard */
sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
}
EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
u16 clk, ctrl_2;
/* In case of UHS-I modes, set High Speed Enable */
- if ((ios->timing == MMC_TIMING_MMC_HS200) ||
+ if ((ios->timing == MMC_TIMING_MMC_HS400) ||
+ (ios->timing == MMC_TIMING_MMC_HS200) ||
(ios->timing == MMC_TIMING_MMC_DDR52) ||
(ios->timing == MMC_TIMING_UHS_SDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR104) ||
* tuning function has to be executed.
*/
switch (host->timing) {
+ case MMC_TIMING_MMC_HS400:
case MMC_TIMING_MMC_HS200:
case MMC_TIMING_UHS_SDR104:
break;
*/
if (!(host->flags & SDHCI_DEVICE_DEAD) &&
((mrq->cmd && mrq->cmd->error) ||
- (mrq->data && (mrq->data->error ||
- (mrq->data->stop && mrq->data->stop->error))) ||
- (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
+ (mrq->sbc && mrq->sbc->error) ||
+ (mrq->data && ((mrq->data->error && !mrq->data->stop) ||
+ (mrq->data->stop && mrq->data->stop->error))) ||
+ (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST))) {
/* Some controllers need this kick or reset won't work here */
if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
}
#ifdef CONFIG_MMC_DEBUG
-static void sdhci_show_adma_error(struct sdhci_host *host)
+static void sdhci_adma_show_error(struct sdhci_host *host)
{
const char *name = mmc_hostname(host->mmc);
- u8 *desc = host->adma_desc;
- __le32 *dma;
- __le16 *len;
- u8 attr;
+ void *desc = host->adma_table;
sdhci_dumpregs(host);
while (true) {
- dma = (__le32 *)(desc + 4);
- len = (__le16 *)(desc + 2);
- attr = *desc;
-
- DBG("%s: %p: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
- name, desc, le32_to_cpu(*dma), le16_to_cpu(*len), attr);
+ struct sdhci_adma2_64_desc *dma_desc = desc;
+
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ DBG("%s: %p: DMA 0x%08x%08x, LEN 0x%04x, Attr=0x%02x\n",
+ name, desc, le32_to_cpu(dma_desc->addr_hi),
+ le32_to_cpu(dma_desc->addr_lo),
+ le16_to_cpu(dma_desc->len),
+ le16_to_cpu(dma_desc->cmd));
+ else
+ DBG("%s: %p: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
+ name, desc, le32_to_cpu(dma_desc->addr_lo),
+ le16_to_cpu(dma_desc->len),
+ le16_to_cpu(dma_desc->cmd));
- desc += 8;
+ desc += host->desc_sz;
- if (attr & 2)
+ if (dma_desc->cmd & cpu_to_le16(ADMA2_END))
break;
}
}
#else
-static void sdhci_show_adma_error(struct sdhci_host *host) { }
+static void sdhci_adma_show_error(struct sdhci_host *host) { }
#endif
static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
host->data->error = -EILSEQ;
else if (intmask & SDHCI_INT_ADMA_ERROR) {
pr_err("%s: ADMA error\n", mmc_hostname(host->mmc));
- sdhci_show_adma_error(host);
+ sdhci_adma_show_error(host);
host->data->error = -EIO;
if (host->ops->adma_workaround)
host->ops->adma_workaround(host, intmask);
host->flags &= ~SDHCI_USE_ADMA;
}
+ /*
+ * It is assumed that a 64-bit capable device has set a 64-bit DMA mask
+ * and *must* do 64-bit DMA. A driver has the opportunity to change
+ * that during the first call to ->enable_dma(). Similarly
+ * SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
+ * implement.
+ */
+ if (sdhci_readl(host, SDHCI_CAPABILITIES) & SDHCI_CAN_64BIT)
+ host->flags |= SDHCI_USE_64_BIT_DMA;
+
if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
if (host->ops->enable_dma) {
if (host->ops->enable_dma(host)) {
}
}
+ /* SDMA does not support 64-bit DMA */
+ if (host->flags & SDHCI_USE_64_BIT_DMA)
+ host->flags &= ~SDHCI_USE_SDMA;
+
if (host->flags & SDHCI_USE_ADMA) {
/*
- * We need to allocate descriptors for all sg entries
- * (128) and potentially one alignment transfer for
- * each of those entries.
+ * The DMA descriptor table size is calculated as the maximum
+ * number of segments times 2, to allow for an alignment
+ * descriptor for each segment, plus 1 for a nop end descriptor,
+ * all multipled by the descriptor size.
*/
- host->adma_desc = dma_alloc_coherent(mmc_dev(mmc),
- ADMA_SIZE, &host->adma_addr,
- GFP_KERNEL);
- host->align_buffer = kmalloc(128 * 4, GFP_KERNEL);
- if (!host->adma_desc || !host->align_buffer) {
- dma_free_coherent(mmc_dev(mmc), ADMA_SIZE,
- host->adma_desc, host->adma_addr);
+ if (host->flags & SDHCI_USE_64_BIT_DMA) {
+ host->adma_table_sz = (SDHCI_MAX_SEGS * 2 + 1) *
+ SDHCI_ADMA2_64_DESC_SZ;
+ host->align_buffer_sz = SDHCI_MAX_SEGS *
+ SDHCI_ADMA2_64_ALIGN;
+ host->desc_sz = SDHCI_ADMA2_64_DESC_SZ;
+ host->align_sz = SDHCI_ADMA2_64_ALIGN;
+ host->align_mask = SDHCI_ADMA2_64_ALIGN - 1;
+ } else {
+ host->adma_table_sz = (SDHCI_MAX_SEGS * 2 + 1) *
+ SDHCI_ADMA2_32_DESC_SZ;
+ host->align_buffer_sz = SDHCI_MAX_SEGS *
+ SDHCI_ADMA2_32_ALIGN;
+ host->desc_sz = SDHCI_ADMA2_32_DESC_SZ;
+ host->align_sz = SDHCI_ADMA2_32_ALIGN;
+ host->align_mask = SDHCI_ADMA2_32_ALIGN - 1;
+ }
+ host->adma_table = dma_alloc_coherent(mmc_dev(mmc),
+ host->adma_table_sz,
+ &host->adma_addr,
+ GFP_KERNEL);
+ host->align_buffer = kmalloc(host->align_buffer_sz, GFP_KERNEL);
+ if (!host->adma_table || !host->align_buffer) {
+ dma_free_coherent(mmc_dev(mmc), host->adma_table_sz,
+ host->adma_table, host->adma_addr);
kfree(host->align_buffer);
pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
mmc_hostname(mmc));
host->flags &= ~SDHCI_USE_ADMA;
- host->adma_desc = NULL;
+ host->adma_table = NULL;
host->align_buffer = NULL;
- } else if (host->adma_addr & 3) {
+ } else if (host->adma_addr & host->align_mask) {
pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
mmc_hostname(mmc));
host->flags &= ~SDHCI_USE_ADMA;
- dma_free_coherent(mmc_dev(mmc), ADMA_SIZE,
- host->adma_desc, host->adma_addr);
+ dma_free_coherent(mmc_dev(mmc), host->adma_table_sz,
+ host->adma_table, host->adma_addr);
kfree(host->align_buffer);
- host->adma_desc = NULL;
+ host->adma_table = NULL;
host->align_buffer = NULL;
}
}
if (ret) {
pr_warn("%s: Failed to enable vqmmc regulator: %d\n",
mmc_hostname(mmc), ret);
- mmc->supply.vqmmc = NULL;
+ mmc->supply.vqmmc = ERR_PTR(-EINVAL);
}
}
/* SD3.0: SDR104 is supported so (for eMMC) the caps2
* field can be promoted to support HS200.
*/
- if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200)) {
+ if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
mmc->caps2 |= MMC_CAP2_HS200;
- if (IS_ERR(mmc->supply.vqmmc) ||
- !regulator_is_supported_voltage
- (mmc->supply.vqmmc, 1100000, 1300000))
- mmc->caps2 &= ~MMC_CAP2_HS200_1_2V_SDR;
- }
} else if (caps[1] & SDHCI_SUPPORT_SDR50)
mmc->caps |= MMC_CAP_UHS_SDR50;
+ if (host->quirks2 & SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 &&
+ (caps[1] & SDHCI_SUPPORT_HS400))
+ mmc->caps2 |= MMC_CAP2_HS400;
+
+ if ((mmc->caps2 & MMC_CAP2_HSX00_1_2V) &&
+ (IS_ERR(mmc->supply.vqmmc) ||
+ !regulator_is_supported_voltage(mmc->supply.vqmmc, 1100000,
+ 1300000)))
+ mmc->caps2 &= ~MMC_CAP2_HSX00_1_2V;
+
if ((caps[1] & SDHCI_SUPPORT_DDR50) &&
!(host->quirks2 & SDHCI_QUIRK2_BROKEN_DDR50))
mmc->caps |= MMC_CAP_UHS_DDR50;
* can do scatter/gather or not.
*/
if (host->flags & SDHCI_USE_ADMA)
- mmc->max_segs = 128;
+ mmc->max_segs = SDHCI_MAX_SEGS;
else if (host->flags & SDHCI_USE_SDMA)
mmc->max_segs = 1;
else /* PIO */
- mmc->max_segs = 128;
+ mmc->max_segs = SDHCI_MAX_SEGS;
/*
* Maximum number of sectors in one transfer. Limited by DMA boundary
pr_info("%s: SDHCI controller on %s [%s] using %s\n",
mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
- (host->flags & SDHCI_USE_ADMA) ? "ADMA" :
+ (host->flags & SDHCI_USE_ADMA) ?
+ (host->flags & SDHCI_USE_64_BIT_DMA) ? "ADMA 64-bit" : "ADMA" :
(host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
sdhci_enable_card_detection(host);
tasklet_kill(&host->finish_tasklet);
- if (!IS_ERR(mmc->supply.vmmc))
- regulator_disable(mmc->supply.vmmc);
-
if (!IS_ERR(mmc->supply.vqmmc))
regulator_disable(mmc->supply.vqmmc);
- if (host->adma_desc)
- dma_free_coherent(mmc_dev(mmc), ADMA_SIZE,
- host->adma_desc, host->adma_addr);
+ if (host->adma_table)
+ dma_free_coherent(mmc_dev(mmc), host->adma_table_sz,
+ host->adma_table, host->adma_addr);
kfree(host->align_buffer);
- host->adma_desc = NULL;
+ host->adma_table = NULL;
host->align_buffer = NULL;
}
#define SDHCI_CTRL_UHS_SDR50 0x0002
#define SDHCI_CTRL_UHS_SDR104 0x0003
#define SDHCI_CTRL_UHS_DDR50 0x0004
-#define SDHCI_CTRL_HS_SDR200 0x0005 /* reserved value in SDIO spec */
+#define SDHCI_CTRL_HS400 0x0005 /* Non-standard */
#define SDHCI_CTRL_VDD_180 0x0008
#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
#define SDHCI_CTRL_DRV_TYPE_B 0x0000
#define SDHCI_RETUNING_MODE_SHIFT 14
#define SDHCI_CLOCK_MUL_MASK 0x00FF0000
#define SDHCI_CLOCK_MUL_SHIFT 16
+#define SDHCI_SUPPORT_HS400 0x80000000 /* Non-standard */
#define SDHCI_CAPABILITIES_1 0x44
/* 55-57 reserved */
#define SDHCI_ADMA_ADDRESS 0x58
+#define SDHCI_ADMA_ADDRESS_HI 0x5C
/* 60-FB reserved */
#define SDHCI_PRESET_FOR_SDR50 0x6A
#define SDHCI_PRESET_FOR_SDR104 0x6C
#define SDHCI_PRESET_FOR_DDR50 0x6E
+#define SDHCI_PRESET_FOR_HS400 0x74 /* Non-standard */
#define SDHCI_PRESET_DRV_MASK 0xC000
#define SDHCI_PRESET_DRV_SHIFT 14
#define SDHCI_PRESET_CLKGEN_SEL_MASK 0x400
#define SDHCI_DEFAULT_BOUNDARY_SIZE (512 * 1024)
#define SDHCI_DEFAULT_BOUNDARY_ARG (ilog2(SDHCI_DEFAULT_BOUNDARY_SIZE) - 12)
+/* ADMA2 32-bit DMA descriptor size */
+#define SDHCI_ADMA2_32_DESC_SZ 8
+
+/* ADMA2 32-bit DMA alignment */
+#define SDHCI_ADMA2_32_ALIGN 4
+
+/* ADMA2 32-bit descriptor */
+struct sdhci_adma2_32_desc {
+ __le16 cmd;
+ __le16 len;
+ __le32 addr;
+} __packed __aligned(SDHCI_ADMA2_32_ALIGN);
+
+/* ADMA2 64-bit DMA descriptor size */
+#define SDHCI_ADMA2_64_DESC_SZ 12
+
+/* ADMA2 64-bit DMA alignment */
+#define SDHCI_ADMA2_64_ALIGN 8
+
+/*
+ * ADMA2 64-bit descriptor. Note 12-byte descriptor can't always be 8-byte
+ * aligned.
+ */
+struct sdhci_adma2_64_desc {
+ __le16 cmd;
+ __le16 len;
+ __le32 addr_lo;
+ __le32 addr_hi;
+} __packed __aligned(4);
+
+#define ADMA2_TRAN_VALID 0x21
+#define ADMA2_NOP_END_VALID 0x3
+#define ADMA2_END 0x2
+
+/*
+ * Maximum segments assuming a 512KiB maximum requisition size and a minimum
+ * 4KiB page size.
+ */
+#define SDHCI_MAX_SEGS 128
+
struct sdhci_ops {
#ifdef CONFIG_MMC_SDHCI_IO_ACCESSORS
u32 (*read_l)(struct sdhci_host *host, int reg);
#include <linux/err.h>
#include <linux/clk.h>
-#include <linux/clk-private.h>
#include <linux/clk/sunxi.h>
#include <linux/gpio.h>
--- /dev/null
+/*
+ * Toshiba PCI Secure Digital Host Controller Interface driver
+ *
+ * Copyright (C) 2014 Ondrej Zary
+ * Copyright (C) 2007 Richard Betts, All Rights Reserved.
+ *
+ * Based on asic3_mmc.c, copyright (c) 2005 SDG Systems, LLC and,
+ * sdhci.c, copyright (C) 2005-2006 Pierre Ossman
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/scatterlist.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <linux/mmc/host.h>
+#include <linux/mmc/mmc.h>
+
+#include "toshsd.h"
+
+#define DRIVER_NAME "toshsd"
+
+static const struct pci_device_id pci_ids[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_TOSHIBA, 0x0805) },
+ { /* end: all zeroes */ },
+};
+
+MODULE_DEVICE_TABLE(pci, pci_ids);
+
+static void toshsd_init(struct toshsd_host *host)
+{
+ /* enable clock */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP,
+ SD_PCICFG_CLKSTOP_ENABLE_ALL);
+ pci_write_config_byte(host->pdev, SD_PCICFG_CARDDETECT, 2);
+
+ /* reset */
+ iowrite16(0, host->ioaddr + SD_SOFTWARERESET); /* assert */
+ mdelay(2);
+ iowrite16(1, host->ioaddr + SD_SOFTWARERESET); /* deassert */
+ mdelay(2);
+
+ /* Clear card registers */
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+ iowrite32(0, host->ioaddr + SD_CARDSTATUS);
+ iowrite32(0, host->ioaddr + SD_ERRORSTATUS0);
+ iowrite16(0, host->ioaddr + SD_STOPINTERNAL);
+
+ /* SDIO clock? */
+ iowrite16(0x100, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL);
+
+ /* enable LED */
+ pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE1,
+ SD_PCICFG_LED_ENABLE1_START);
+ pci_write_config_byte(host->pdev, SD_PCICFG_SDLED_ENABLE2,
+ SD_PCICFG_LED_ENABLE2_START);
+
+ /* set interrupt masks */
+ iowrite32(~(u32)(SD_CARD_RESP_END | SD_CARD_RW_END
+ | SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0
+ | SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE
+ | SD_BUF_CMD_TIMEOUT),
+ host->ioaddr + SD_INTMASKCARD);
+
+ iowrite16(0x1000, host->ioaddr + SD_TRANSACTIONCTRL);
+}
+
+/* Set MMC clock / power.
+ * Note: This controller uses a simple divider scheme therefore it cannot run
+ * SD/MMC cards at full speed (24/20MHz). HCLK (=33MHz PCI clock?) is too high
+ * and the next slowest is 16MHz (div=2).
+ */
+static void __toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ if (ios->clock) {
+ u16 clk;
+ int div = 1;
+
+ while (ios->clock < HCLK / div)
+ div *= 2;
+
+ clk = div >> 2;
+
+ if (div == 1) { /* disable the divider */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE,
+ SD_PCICFG_CLKMODE_DIV_DISABLE);
+ clk |= SD_CARDCLK_DIV_DISABLE;
+ } else
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKMODE, 0);
+
+ clk |= SD_CARDCLK_ENABLE_CLOCK;
+ iowrite16(clk, host->ioaddr + SD_CARDCLOCKCTRL);
+
+ mdelay(10);
+ } else
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+
+ switch (ios->power_mode) {
+ case MMC_POWER_OFF:
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1,
+ SD_PCICFG_PWR1_OFF);
+ mdelay(1);
+ break;
+ case MMC_POWER_UP:
+ break;
+ case MMC_POWER_ON:
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1,
+ SD_PCICFG_PWR1_33V);
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER2,
+ SD_PCICFG_PWR2_AUTO);
+ mdelay(20);
+ break;
+ }
+
+ switch (ios->bus_width) {
+ case MMC_BUS_WIDTH_1:
+ iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14)
+ | SD_CARDOPT_C2_MODULE_ABSENT
+ | SD_CARDOPT_DATA_XFR_WIDTH_1,
+ host->ioaddr + SD_CARDOPTIONSETUP);
+ break;
+ case MMC_BUS_WIDTH_4:
+ iowrite16(SD_CARDOPT_REQUIRED | SD_CARDOPT_DATA_RESP_TIMEOUT(14)
+ | SD_CARDOPT_C2_MODULE_ABSENT
+ | SD_CARDOPT_DATA_XFR_WIDTH_4,
+ host->ioaddr + SD_CARDOPTIONSETUP);
+ break;
+ }
+}
+
+static void toshsd_set_led(struct toshsd_host *host, unsigned char state)
+{
+ iowrite16(state, host->ioaddr + SDIO_BASE + SDIO_LEDCTRL);
+}
+
+static void toshsd_finish_request(struct toshsd_host *host)
+{
+ struct mmc_request *mrq = host->mrq;
+
+ /* Write something to end the command */
+ host->mrq = NULL;
+ host->cmd = NULL;
+ host->data = NULL;
+
+ toshsd_set_led(host, 0);
+ mmc_request_done(host->mmc, mrq);
+}
+
+static irqreturn_t toshsd_thread_irq(int irq, void *dev_id)
+{
+ struct toshsd_host *host = dev_id;
+ struct mmc_data *data = host->data;
+ struct sg_mapping_iter *sg_miter = &host->sg_miter;
+ unsigned short *buf;
+ int count;
+ unsigned long flags;
+
+ if (!data) {
+ dev_warn(&host->pdev->dev, "Spurious Data IRQ\n");
+ if (host->cmd) {
+ host->cmd->error = -EIO;
+ toshsd_finish_request(host);
+ }
+ return IRQ_NONE;
+ }
+ spin_lock_irqsave(&host->lock, flags);
+
+ if (!sg_miter_next(sg_miter))
+ return IRQ_HANDLED;
+ buf = sg_miter->addr;
+
+ /* Ensure we dont read more than one block. The chip will interrupt us
+ * When the next block is available.
+ */
+ count = sg_miter->length;
+ if (count > data->blksz)
+ count = data->blksz;
+
+ dev_dbg(&host->pdev->dev, "count: %08x, flags %08x\n", count,
+ data->flags);
+
+ /* Transfer the data */
+ if (data->flags & MMC_DATA_READ)
+ ioread32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2);
+ else
+ iowrite32_rep(host->ioaddr + SD_DATAPORT, buf, count >> 2);
+
+ sg_miter->consumed = count;
+ sg_miter_stop(sg_miter);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+
+ return IRQ_HANDLED;
+}
+
+static void toshsd_cmd_irq(struct toshsd_host *host)
+{
+ struct mmc_command *cmd = host->cmd;
+ u8 *buf;
+ u16 data;
+
+ if (!host->cmd) {
+ dev_warn(&host->pdev->dev, "Spurious CMD irq\n");
+ return;
+ }
+ buf = (u8 *)cmd->resp;
+ host->cmd = NULL;
+
+ if (cmd->flags & MMC_RSP_PRESENT && cmd->flags & MMC_RSP_136) {
+ /* R2 */
+ buf[12] = 0xff;
+ data = ioread16(host->ioaddr + SD_RESPONSE0);
+ buf[13] = data & 0xff;
+ buf[14] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE1);
+ buf[15] = data & 0xff;
+ buf[8] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE2);
+ buf[9] = data & 0xff;
+ buf[10] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE3);
+ buf[11] = data & 0xff;
+ buf[4] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE4);
+ buf[5] = data & 0xff;
+ buf[6] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE5);
+ buf[7] = data & 0xff;
+ buf[0] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE6);
+ buf[1] = data & 0xff;
+ buf[2] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE7);
+ buf[3] = data & 0xff;
+ } else if (cmd->flags & MMC_RSP_PRESENT) {
+ /* R1, R1B, R3, R6, R7 */
+ data = ioread16(host->ioaddr + SD_RESPONSE0);
+ buf[0] = data & 0xff;
+ buf[1] = data >> 8;
+ data = ioread16(host->ioaddr + SD_RESPONSE1);
+ buf[2] = data & 0xff;
+ buf[3] = data >> 8;
+ }
+
+ dev_dbg(&host->pdev->dev, "Command IRQ complete %d %d %x\n",
+ cmd->opcode, cmd->error, cmd->flags);
+
+ /* If there is data to handle we will
+ * finish the request in the mmc_data_end_irq handler.*/
+ if (host->data)
+ return;
+
+ toshsd_finish_request(host);
+}
+
+static void toshsd_data_end_irq(struct toshsd_host *host)
+{
+ struct mmc_data *data = host->data;
+
+ host->data = NULL;
+
+ if (!data) {
+ dev_warn(&host->pdev->dev, "Spurious data end IRQ\n");
+ return;
+ }
+
+ if (data->error == 0)
+ data->bytes_xfered = data->blocks * data->blksz;
+ else
+ data->bytes_xfered = 0;
+
+ dev_dbg(&host->pdev->dev, "Completed data request xfr=%d\n",
+ data->bytes_xfered);
+
+ iowrite16(0, host->ioaddr + SD_STOPINTERNAL);
+
+ toshsd_finish_request(host);
+}
+
+static irqreturn_t toshsd_irq(int irq, void *dev_id)
+{
+ struct toshsd_host *host = dev_id;
+ u32 int_reg, int_mask, int_status, detail;
+ int error = 0, ret = IRQ_HANDLED;
+
+ spin_lock(&host->lock);
+ int_status = ioread32(host->ioaddr + SD_CARDSTATUS);
+ int_mask = ioread32(host->ioaddr + SD_INTMASKCARD);
+ int_reg = int_status & ~int_mask & ~IRQ_DONT_CARE_BITS;
+
+ dev_dbg(&host->pdev->dev, "IRQ status:%x mask:%x\n",
+ int_status, int_mask);
+
+ /* nothing to do: it's not our IRQ */
+ if (!int_reg) {
+ ret = IRQ_NONE;
+ goto irq_end;
+ }
+
+ if (int_reg & SD_BUF_CMD_TIMEOUT) {
+ error = -ETIMEDOUT;
+ dev_dbg(&host->pdev->dev, "Timeout\n");
+ } else if (int_reg & SD_BUF_CRC_ERR) {
+ error = -EILSEQ;
+ dev_err(&host->pdev->dev, "BadCRC\n");
+ } else if (int_reg & (SD_BUF_ILLEGAL_ACCESS
+ | SD_BUF_CMD_INDEX_ERR
+ | SD_BUF_STOP_BIT_END_ERR
+ | SD_BUF_OVERFLOW
+ | SD_BUF_UNDERFLOW
+ | SD_BUF_DATA_TIMEOUT)) {
+ dev_err(&host->pdev->dev, "Buffer status error: { %s%s%s%s%s%s}\n",
+ int_reg & SD_BUF_ILLEGAL_ACCESS ? "ILLEGAL_ACC " : "",
+ int_reg & SD_BUF_CMD_INDEX_ERR ? "CMD_INDEX " : "",
+ int_reg & SD_BUF_STOP_BIT_END_ERR ? "STOPBIT_END " : "",
+ int_reg & SD_BUF_OVERFLOW ? "OVERFLOW " : "",
+ int_reg & SD_BUF_UNDERFLOW ? "UNDERFLOW " : "",
+ int_reg & SD_BUF_DATA_TIMEOUT ? "DATA_TIMEOUT " : "");
+
+ detail = ioread32(host->ioaddr + SD_ERRORSTATUS0);
+ dev_err(&host->pdev->dev, "detail error status { %s%s%s%s%s%s%s%s%s%s%s%s%s}\n",
+ detail & SD_ERR0_RESP_CMD_ERR ? "RESP_CMD " : "",
+ detail & SD_ERR0_RESP_NON_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "",
+ detail & SD_ERR0_RESP_CMD12_END_BIT_ERR ? "RESP_END_BIT " : "",
+ detail & SD_ERR0_READ_DATA_END_BIT_ERR ? "READ_DATA_END_BIT " : "",
+ detail & SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR ? "WRITE_CMD_END_BIT " : "",
+ detail & SD_ERR0_RESP_NON_CMD12_CRC_ERR ? "RESP_CRC " : "",
+ detail & SD_ERR0_RESP_CMD12_CRC_ERR ? "RESP_CRC " : "",
+ detail & SD_ERR0_READ_DATA_CRC_ERR ? "READ_DATA_CRC " : "",
+ detail & SD_ERR0_WRITE_CMD_CRC_ERR ? "WRITE_CMD_CRC " : "",
+ detail & SD_ERR1_NO_CMD_RESP ? "NO_CMD_RESP " : "",
+ detail & SD_ERR1_TIMEOUT_READ_DATA ? "READ_DATA_TIMEOUT " : "",
+ detail & SD_ERR1_TIMEOUT_CRS_STATUS ? "CRS_STATUS_TIMEOUT " : "",
+ detail & SD_ERR1_TIMEOUT_CRC_BUSY ? "CRC_BUSY_TIMEOUT " : "");
+ error = -EIO;
+ }
+
+ if (error) {
+ if (host->cmd)
+ host->cmd->error = error;
+
+ if (error == -ETIMEDOUT) {
+ iowrite32(int_status &
+ ~(SD_BUF_CMD_TIMEOUT | SD_CARD_RESP_END),
+ host->ioaddr + SD_CARDSTATUS);
+ } else {
+ toshsd_init(host);
+ __toshsd_set_ios(host->mmc, &host->mmc->ios);
+ goto irq_end;
+ }
+ }
+
+ /* Card insert/remove. The mmc controlling code is stateless. */
+ if (int_reg & (SD_CARD_CARD_INSERTED_0 | SD_CARD_CARD_REMOVED_0)) {
+ iowrite32(int_status &
+ ~(SD_CARD_CARD_REMOVED_0 | SD_CARD_CARD_INSERTED_0),
+ host->ioaddr + SD_CARDSTATUS);
+
+ if (int_reg & SD_CARD_CARD_INSERTED_0)
+ toshsd_init(host);
+
+ mmc_detect_change(host->mmc, 1);
+ }
+
+ /* Data transfer */
+ if (int_reg & (SD_BUF_READ_ENABLE | SD_BUF_WRITE_ENABLE)) {
+ iowrite32(int_status &
+ ~(SD_BUF_WRITE_ENABLE | SD_BUF_READ_ENABLE),
+ host->ioaddr + SD_CARDSTATUS);
+
+ ret = IRQ_WAKE_THREAD;
+ goto irq_end;
+ }
+
+ /* Command completion */
+ if (int_reg & SD_CARD_RESP_END) {
+ iowrite32(int_status & ~(SD_CARD_RESP_END),
+ host->ioaddr + SD_CARDSTATUS);
+ toshsd_cmd_irq(host);
+ }
+
+ /* Data transfer completion */
+ if (int_reg & SD_CARD_RW_END) {
+ iowrite32(int_status & ~(SD_CARD_RW_END),
+ host->ioaddr + SD_CARDSTATUS);
+ toshsd_data_end_irq(host);
+ }
+irq_end:
+ spin_unlock(&host->lock);
+ return ret;
+}
+
+static void toshsd_start_cmd(struct toshsd_host *host, struct mmc_command *cmd)
+{
+ struct mmc_data *data = host->data;
+ int c = cmd->opcode;
+
+ dev_dbg(&host->pdev->dev, "Command opcode: %d\n", cmd->opcode);
+
+ if (cmd->opcode == MMC_STOP_TRANSMISSION) {
+ iowrite16(SD_STOPINT_ISSUE_CMD12,
+ host->ioaddr + SD_STOPINTERNAL);
+
+ cmd->resp[0] = cmd->opcode;
+ cmd->resp[1] = 0;
+ cmd->resp[2] = 0;
+ cmd->resp[3] = 0;
+
+ toshsd_finish_request(host);
+ return;
+ }
+
+ switch (mmc_resp_type(cmd)) {
+ case MMC_RSP_NONE:
+ c |= SD_CMD_RESP_TYPE_NONE;
+ break;
+
+ case MMC_RSP_R1:
+ c |= SD_CMD_RESP_TYPE_EXT_R1;
+ break;
+ case MMC_RSP_R1B:
+ c |= SD_CMD_RESP_TYPE_EXT_R1B;
+ break;
+ case MMC_RSP_R2:
+ c |= SD_CMD_RESP_TYPE_EXT_R2;
+ break;
+ case MMC_RSP_R3:
+ c |= SD_CMD_RESP_TYPE_EXT_R3;
+ break;
+
+ default:
+ dev_err(&host->pdev->dev, "Unknown response type %d\n",
+ mmc_resp_type(cmd));
+ break;
+ }
+
+ host->cmd = cmd;
+
+ if (cmd->opcode == MMC_APP_CMD)
+ c |= SD_CMD_TYPE_ACMD;
+
+ if (cmd->opcode == MMC_GO_IDLE_STATE)
+ c |= (3 << 8); /* removed from ipaq-asic3.h for some reason */
+
+ if (data) {
+ c |= SD_CMD_DATA_PRESENT;
+
+ if (data->blocks > 1) {
+ iowrite16(SD_STOPINT_AUTO_ISSUE_CMD12,
+ host->ioaddr + SD_STOPINTERNAL);
+ c |= SD_CMD_MULTI_BLOCK;
+ }
+
+ if (data->flags & MMC_DATA_READ)
+ c |= SD_CMD_TRANSFER_READ;
+
+ /* MMC_DATA_WRITE does not require a bit to be set */
+ }
+
+ /* Send the command */
+ iowrite32(cmd->arg, host->ioaddr + SD_ARG0);
+ iowrite16(c, host->ioaddr + SD_CMD);
+}
+
+static void toshsd_start_data(struct toshsd_host *host, struct mmc_data *data)
+{
+ unsigned int flags = SG_MITER_ATOMIC;
+
+ dev_dbg(&host->pdev->dev, "setup data transfer: blocksize %08x nr_blocks %d, offset: %08x\n",
+ data->blksz, data->blocks, data->sg->offset);
+
+ host->data = data;
+
+ if (data->flags & MMC_DATA_READ)
+ flags |= SG_MITER_TO_SG;
+ else
+ flags |= SG_MITER_FROM_SG;
+
+ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
+
+ /* Set transfer length and blocksize */
+ iowrite16(data->blocks, host->ioaddr + SD_BLOCKCOUNT);
+ iowrite16(data->blksz, host->ioaddr + SD_CARDXFERDATALEN);
+}
+
+/* Process requests from the MMC layer */
+static void toshsd_request(struct mmc_host *mmc, struct mmc_request *mrq)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ /* abort if card not present */
+ if (!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0)) {
+ mrq->cmd->error = -ENOMEDIUM;
+ mmc_request_done(mmc, mrq);
+ return;
+ }
+
+ spin_lock_irqsave(&host->lock, flags);
+
+ WARN_ON(host->mrq != NULL);
+
+ host->mrq = mrq;
+
+ if (mrq->data)
+ toshsd_start_data(host, mrq->data);
+
+ toshsd_set_led(host, 1);
+
+ toshsd_start_cmd(host, mrq->cmd);
+
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static void toshsd_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+ unsigned long flags;
+
+ spin_lock_irqsave(&host->lock, flags);
+ __toshsd_set_ios(mmc, ios);
+ spin_unlock_irqrestore(&host->lock, flags);
+}
+
+static int toshsd_get_ro(struct mmc_host *mmc)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ /* active low */
+ return !(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_WRITE_PROTECT);
+}
+
+static int toshsd_get_cd(struct mmc_host *mmc)
+{
+ struct toshsd_host *host = mmc_priv(mmc);
+
+ return !!(ioread16(host->ioaddr + SD_CARDSTATUS) & SD_CARD_PRESENT_0);
+}
+
+static struct mmc_host_ops toshsd_ops = {
+ .request = toshsd_request,
+ .set_ios = toshsd_set_ios,
+ .get_ro = toshsd_get_ro,
+ .get_cd = toshsd_get_cd,
+};
+
+
+static void toshsd_powerdown(struct toshsd_host *host)
+{
+ /* mask all interrupts */
+ iowrite32(0xffffffff, host->ioaddr + SD_INTMASKCARD);
+ /* disable card clock */
+ iowrite16(0x000, host->ioaddr + SDIO_BASE + SDIO_CLOCKNWAITCTRL);
+ iowrite16(0, host->ioaddr + SD_CARDCLOCKCTRL);
+ /* power down card */
+ pci_write_config_byte(host->pdev, SD_PCICFG_POWER1, SD_PCICFG_PWR1_OFF);
+ /* disable clock */
+ pci_write_config_byte(host->pdev, SD_PCICFG_CLKSTOP, 0);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int toshsd_pm_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+
+ toshsd_powerdown(host);
+
+ pci_save_state(pdev);
+ pci_enable_wake(pdev, PCI_D3hot, 0);
+ pci_disable_device(pdev);
+ pci_set_power_state(pdev, PCI_D3hot);
+
+ return 0;
+}
+
+static int toshsd_pm_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+ int ret;
+
+ pci_set_power_state(pdev, PCI_D0);
+ pci_restore_state(pdev);
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ toshsd_init(host);
+
+ return 0;
+}
+#endif /* CONFIG_PM_SLEEP */
+
+static int toshsd_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ int ret;
+ struct toshsd_host *host;
+ struct mmc_host *mmc;
+ resource_size_t base;
+
+ ret = pci_enable_device(pdev);
+ if (ret)
+ return ret;
+
+ mmc = mmc_alloc_host(sizeof(struct toshsd_host), &pdev->dev);
+ if (!mmc) {
+ ret = -ENOMEM;
+ goto err;
+ }
+
+ host = mmc_priv(mmc);
+ host->mmc = mmc;
+
+ host->pdev = pdev;
+ pci_set_drvdata(pdev, host);
+
+ ret = pci_request_regions(pdev, DRIVER_NAME);
+ if (ret)
+ goto free;
+
+ host->ioaddr = pci_iomap(pdev, 0, 0);
+ if (!host->ioaddr) {
+ ret = -ENOMEM;
+ goto release;
+ }
+
+ /* Set MMC host parameters */
+ mmc->ops = &toshsd_ops;
+ mmc->caps = MMC_CAP_4_BIT_DATA;
+ mmc->ocr_avail = MMC_VDD_32_33;
+
+ mmc->f_min = HCLK / 512;
+ mmc->f_max = HCLK;
+
+ spin_lock_init(&host->lock);
+
+ toshsd_init(host);
+
+ ret = request_threaded_irq(pdev->irq, toshsd_irq, toshsd_thread_irq,
+ IRQF_SHARED, DRIVER_NAME, host);
+ if (ret)
+ goto unmap;
+
+ mmc_add_host(mmc);
+
+ base = pci_resource_start(pdev, 0);
+ dev_dbg(&pdev->dev, "MMIO %pa, IRQ %d\n", &base, pdev->irq);
+
+ pm_suspend_ignore_children(&pdev->dev, 1);
+
+ return 0;
+
+unmap:
+ pci_iounmap(pdev, host->ioaddr);
+release:
+ pci_release_regions(pdev);
+free:
+ mmc_free_host(mmc);
+ pci_set_drvdata(pdev, NULL);
+err:
+ pci_disable_device(pdev);
+ return ret;
+}
+
+static void toshsd_remove(struct pci_dev *pdev)
+{
+ struct toshsd_host *host = pci_get_drvdata(pdev);
+
+ mmc_remove_host(host->mmc);
+ toshsd_powerdown(host);
+ free_irq(pdev->irq, host);
+ pci_iounmap(pdev, host->ioaddr);
+ pci_release_regions(pdev);
+ mmc_free_host(host->mmc);
+ pci_set_drvdata(pdev, NULL);
+ pci_disable_device(pdev);
+}
+
+static const struct dev_pm_ops toshsd_pm_ops = {
+ SET_SYSTEM_SLEEP_PM_OPS(toshsd_pm_suspend, toshsd_pm_resume)
+};
+
+static struct pci_driver toshsd_driver = {
+ .name = DRIVER_NAME,
+ .id_table = pci_ids,
+ .probe = toshsd_probe,
+ .remove = toshsd_remove,
+ .driver.pm = &toshsd_pm_ops,
+};
+
+static int __init toshsd_drv_init(void)
+{
+ return pci_register_driver(&toshsd_driver);
+}
+
+static void __exit toshsd_drv_exit(void)
+{
+ pci_unregister_driver(&toshsd_driver);
+}
+
+module_init(toshsd_drv_init);
+module_exit(toshsd_drv_exit);
+
+MODULE_AUTHOR("Ondrej Zary, Richard Betts");
+MODULE_DESCRIPTION("Toshiba PCI Secure Digital Host Controller Interface driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Toshiba PCI Secure Digital Host Controller Interface driver
+ *
+ * Copyright (C) 2014 Ondrej Zary
+ * Copyright (C) 2007 Richard Betts, All Rights Reserved.
+ *
+ * Based on asic3_mmc.c Copyright (c) 2005 SDG Systems, LLC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or (at
+ * your option) any later version.
+ */
+
+#define HCLK 33000000 /* 33 MHz (PCI clock) */
+
+#define SD_PCICFG_CLKSTOP 0x40 /* 0x1f = clock controller, 0 = stop */
+#define SD_PCICFG_GATEDCLK 0x41 /* Gated clock */
+#define SD_PCICFG_CLKMODE 0x42 /* Control clock of SD controller */
+#define SD_PCICFG_PINSTATUS 0x44 /* R/O: read status of SD pins */
+#define SD_PCICFG_POWER1 0x48
+#define SD_PCICFG_POWER2 0x49
+#define SD_PCICFG_POWER3 0x4a
+#define SD_PCICFG_CARDDETECT 0x4c
+#define SD_PCICFG_SLOTS 0x50 /* R/O: define support slot number */
+#define SD_PCICFG_EXTGATECLK1 0xf0 /* Could be used for gated clock */
+#define SD_PCICFG_EXTGATECLK2 0xf1 /* Could be used for gated clock */
+#define SD_PCICFG_EXTGATECLK3 0xf9 /* Bit 1: double buffer/single buffer */
+#define SD_PCICFG_SDLED_ENABLE1 0xfa
+#define SD_PCICFG_SDLED_ENABLE2 0xfe
+
+#define SD_PCICFG_CLKMODE_DIV_DISABLE BIT(0)
+#define SD_PCICFG_CLKSTOP_ENABLE_ALL 0x1f
+#define SD_PCICFG_LED_ENABLE1_START 0x12
+#define SD_PCICFG_LED_ENABLE2_START 0x80
+
+#define SD_PCICFG_PWR1_33V 0x08 /* Set for 3.3 volts */
+#define SD_PCICFG_PWR1_OFF 0x00 /* Turn off power */
+#define SD_PCICFG_PWR2_AUTO 0x02
+
+#define SD_CMD 0x00 /* also for SDIO */
+#define SD_ARG0 0x04 /* also for SDIO */
+#define SD_ARG1 0x06 /* also for SDIO */
+#define SD_STOPINTERNAL 0x08
+#define SD_BLOCKCOUNT 0x0a /* also for SDIO */
+#define SD_RESPONSE0 0x0c /* also for SDIO */
+#define SD_RESPONSE1 0x0e /* also for SDIO */
+#define SD_RESPONSE2 0x10 /* also for SDIO */
+#define SD_RESPONSE3 0x12 /* also for SDIO */
+#define SD_RESPONSE4 0x14 /* also for SDIO */
+#define SD_RESPONSE5 0x16 /* also for SDIO */
+#define SD_RESPONSE6 0x18 /* also for SDIO */
+#define SD_RESPONSE7 0x1a /* also for SDIO */
+#define SD_CARDSTATUS 0x1c /* also for SDIO */
+#define SD_BUFFERCTRL 0x1e /* also for SDIO */
+#define SD_INTMASKCARD 0x20 /* also for SDIO */
+#define SD_INTMASKBUFFER 0x22 /* also for SDIO */
+#define SD_CARDCLOCKCTRL 0x24
+#define SD_CARDXFERDATALEN 0x26 /* also for SDIO */
+#define SD_CARDOPTIONSETUP 0x28 /* also for SDIO */
+#define SD_ERRORSTATUS0 0x2c /* also for SDIO */
+#define SD_ERRORSTATUS1 0x2e /* also for SDIO */
+#define SD_DATAPORT 0x30 /* also for SDIO */
+#define SD_TRANSACTIONCTRL 0x34 /* also for SDIO */
+#define SD_SOFTWARERESET 0xe0 /* also for SDIO */
+
+/* registers above marked "also for SDIO" and all SDIO registers below can be
+ * accessed at SDIO_BASE + reg address */
+#define SDIO_BASE 0x100
+
+#define SDIO_CARDPORTSEL 0x02
+#define SDIO_CARDINTCTRL 0x36
+#define SDIO_CLOCKNWAITCTRL 0x38
+#define SDIO_HOSTINFORMATION 0x3a
+#define SDIO_ERRORCTRL 0x3c
+#define SDIO_LEDCTRL 0x3e
+
+#define SD_TRANSCTL_SET BIT(8)
+
+#define SD_CARDCLK_DIV_DISABLE BIT(15)
+#define SD_CARDCLK_ENABLE_CLOCK BIT(8)
+#define SD_CARDCLK_CLK_DIV_512 BIT(7)
+#define SD_CARDCLK_CLK_DIV_256 BIT(6)
+#define SD_CARDCLK_CLK_DIV_128 BIT(5)
+#define SD_CARDCLK_CLK_DIV_64 BIT(4)
+#define SD_CARDCLK_CLK_DIV_32 BIT(3)
+#define SD_CARDCLK_CLK_DIV_16 BIT(2)
+#define SD_CARDCLK_CLK_DIV_8 BIT(1)
+#define SD_CARDCLK_CLK_DIV_4 BIT(0)
+#define SD_CARDCLK_CLK_DIV_2 0
+
+#define SD_CARDOPT_REQUIRED 0x000e
+#define SD_CARDOPT_DATA_RESP_TIMEOUT(x) (((x) & 0x0f) << 4) /* 4 bits */
+#define SD_CARDOPT_C2_MODULE_ABSENT BIT(14)
+#define SD_CARDOPT_DATA_XFR_WIDTH_1 (1 << 15)
+#define SD_CARDOPT_DATA_XFR_WIDTH_4 (0 << 15)
+
+#define SD_CMD_TYPE_CMD (0 << 6)
+#define SD_CMD_TYPE_ACMD (1 << 6)
+#define SD_CMD_TYPE_AUTHEN (2 << 6)
+#define SD_CMD_RESP_TYPE_NONE (3 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R1 (4 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R1B (5 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R2 (6 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R3 (7 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R6 (4 << 8)
+#define SD_CMD_RESP_TYPE_EXT_R7 (4 << 8)
+#define SD_CMD_DATA_PRESENT BIT(11)
+#define SD_CMD_TRANSFER_READ BIT(12)
+#define SD_CMD_MULTI_BLOCK BIT(13)
+#define SD_CMD_SECURITY_CMD BIT(14)
+
+#define SD_STOPINT_ISSUE_CMD12 BIT(0)
+#define SD_STOPINT_AUTO_ISSUE_CMD12 BIT(8)
+
+#define SD_CARD_RESP_END BIT(0)
+#define SD_CARD_RW_END BIT(2)
+#define SD_CARD_CARD_REMOVED_0 BIT(3)
+#define SD_CARD_CARD_INSERTED_0 BIT(4)
+#define SD_CARD_PRESENT_0 BIT(5)
+#define SD_CARD_UNK6 BIT(6)
+#define SD_CARD_WRITE_PROTECT BIT(7)
+#define SD_CARD_CARD_REMOVED_3 BIT(8)
+#define SD_CARD_CARD_INSERTED_3 BIT(9)
+#define SD_CARD_PRESENT_3 BIT(10)
+
+#define SD_BUF_CMD_INDEX_ERR BIT(16)
+#define SD_BUF_CRC_ERR BIT(17)
+#define SD_BUF_STOP_BIT_END_ERR BIT(18)
+#define SD_BUF_DATA_TIMEOUT BIT(19)
+#define SD_BUF_OVERFLOW BIT(20)
+#define SD_BUF_UNDERFLOW BIT(21)
+#define SD_BUF_CMD_TIMEOUT BIT(22)
+#define SD_BUF_UNK7 BIT(23)
+#define SD_BUF_READ_ENABLE BIT(24)
+#define SD_BUF_WRITE_ENABLE BIT(25)
+#define SD_BUF_ILLEGAL_FUNCTION BIT(29)
+#define SD_BUF_CMD_BUSY BIT(30)
+#define SD_BUF_ILLEGAL_ACCESS BIT(31)
+
+#define SD_ERR0_RESP_CMD_ERR BIT(0)
+#define SD_ERR0_RESP_NON_CMD12_END_BIT_ERR BIT(2)
+#define SD_ERR0_RESP_CMD12_END_BIT_ERR BIT(3)
+#define SD_ERR0_READ_DATA_END_BIT_ERR BIT(4)
+#define SD_ERR0_WRITE_CRC_STATUS_END_BIT_ERR BIT(5)
+#define SD_ERR0_RESP_NON_CMD12_CRC_ERR BIT(8)
+#define SD_ERR0_RESP_CMD12_CRC_ERR BIT(9)
+#define SD_ERR0_READ_DATA_CRC_ERR BIT(10)
+#define SD_ERR0_WRITE_CMD_CRC_ERR BIT(11)
+
+#define SD_ERR1_NO_CMD_RESP BIT(16)
+#define SD_ERR1_TIMEOUT_READ_DATA BIT(20)
+#define SD_ERR1_TIMEOUT_CRS_STATUS BIT(21)
+#define SD_ERR1_TIMEOUT_CRC_BUSY BIT(22)
+
+#define IRQ_DONT_CARE_BITS (SD_CARD_PRESENT_3 \
+ | SD_CARD_WRITE_PROTECT \
+ | SD_CARD_UNK6 \
+ | SD_CARD_PRESENT_0 \
+ | SD_BUF_UNK7 \
+ | SD_BUF_CMD_BUSY)
+
+struct toshsd_host {
+ struct pci_dev *pdev;
+ struct mmc_host *mmc;
+
+ spinlock_t lock;
+
+ struct mmc_request *mrq;/* Current request */
+ struct mmc_command *cmd;/* Current command */
+ struct mmc_data *data; /* Current data request */
+
+ struct sg_mapping_iter sg_miter; /* for PIO */
+
+ void __iomem *ioaddr; /* mapped address */
+};
bond_option_arp_ip_targets_clear(bond);
nla_for_each_nested(attr, data[IFLA_BOND_ARP_IP_TARGET], rem) {
- __be32 target = nla_get_be32(attr);
+ __be32 target;
+
+ if (nla_len(attr) < sizeof(target))
+ return -EINVAL;
+
+ target = nla_get_be32(attr);
bond_opt_initval(&newval, (__force u64)target);
err = __bond_opt_set(bond, BOND_OPT_ARP_TARGETS,
SUPPORTED_10000baseKR_Full | SUPPORTED_1000baseKX_Full |
SUPPORTED_10000baseKX4_Full;
else if (type == FW_PORT_TYPE_FIBER_XFI ||
- type == FW_PORT_TYPE_FIBER_XAUI || type == FW_PORT_TYPE_SFP)
+ type == FW_PORT_TYPE_FIBER_XAUI || type == FW_PORT_TYPE_SFP) {
v |= SUPPORTED_FIBRE;
- else if (type == FW_PORT_TYPE_BP40_BA)
+ if (caps & FW_PORT_CAP_SPEED_1G)
+ v |= SUPPORTED_1000baseT_Full;
+ if (caps & FW_PORT_CAP_SPEED_10G)
+ v |= SUPPORTED_10000baseT_Full;
+ } else if (type == FW_PORT_TYPE_BP40_BA)
v |= SUPPORTED_40000baseSR4_Full;
if (caps & FW_PORT_CAP_ANEG)
return ret;
}
-#if defined(CONFIG_CPU_SH4) || defined(CONFIG_ARCH_SHMOBILE)
static void sh_eth_set_receive_align(struct sk_buff *skb)
{
- int reserve;
+ uintptr_t reserve = (uintptr_t)skb->data & (SH_ETH_RX_ALIGN - 1);
- reserve = SH4_SKB_RX_ALIGN - ((u32)skb->data & (SH4_SKB_RX_ALIGN - 1));
if (reserve)
- skb_reserve(skb, reserve);
+ skb_reserve(skb, SH_ETH_RX_ALIGN - reserve);
}
-#else
-static void sh_eth_set_receive_align(struct sk_buff *skb)
-{
- skb_reserve(skb, SH2_SH3_SKB_RX_ALIGN);
-}
-#endif
/* CPU <-> EDMAC endian convert */
struct sh_eth_txdesc *txdesc = NULL;
int rx_ringsize = sizeof(*rxdesc) * mdp->num_rx_ring;
int tx_ringsize = sizeof(*txdesc) * mdp->num_tx_ring;
+ int skbuff_size = mdp->rx_buf_sz + SH_ETH_RX_ALIGN - 1;
mdp->cur_rx = 0;
mdp->cur_tx = 0;
for (i = 0; i < mdp->num_rx_ring; i++) {
/* skb */
mdp->rx_skbuff[i] = NULL;
- skb = netdev_alloc_skb(ndev, mdp->rx_buf_sz);
+ skb = netdev_alloc_skb(ndev, skbuff_size);
mdp->rx_skbuff[i] = skb;
if (skb == NULL)
break;
- dma_map_single(&ndev->dev, skb->data, mdp->rx_buf_sz,
- DMA_FROM_DEVICE);
sh_eth_set_receive_align(skb);
/* RX descriptor */
rxdesc = &mdp->rx_ring[i];
+ /* The size of the buffer is a multiple of 16 bytes. */
+ rxdesc->buffer_length = ALIGN(mdp->rx_buf_sz, 16);
+ dma_map_single(&ndev->dev, skb->data, rxdesc->buffer_length,
+ DMA_FROM_DEVICE);
rxdesc->addr = virt_to_phys(PTR_ALIGN(skb->data, 4));
rxdesc->status = cpu_to_edmac(mdp, RD_RACT | RD_RFP);
- /* The size of the buffer is 16 byte boundary. */
- rxdesc->buffer_length = ALIGN(mdp->rx_buf_sz, 16);
/* Rx descriptor address set */
if (i == 0) {
sh_eth_write(ndev, mdp->rx_desc_dma, RDLAR);
struct sk_buff *skb;
u16 pkt_len = 0;
u32 desc_status;
+ int skbuff_size = mdp->rx_buf_sz + SH_ETH_RX_ALIGN - 1;
rxdesc = &mdp->rx_ring[entry];
while (!(rxdesc->status & cpu_to_edmac(mdp, RD_RACT))) {
if (mdp->cd->rpadir)
skb_reserve(skb, NET_IP_ALIGN);
dma_sync_single_for_cpu(&ndev->dev, rxdesc->addr,
- mdp->rx_buf_sz,
+ ALIGN(mdp->rx_buf_sz, 16),
DMA_FROM_DEVICE);
skb_put(skb, pkt_len);
skb->protocol = eth_type_trans(skb, ndev);
rxdesc->buffer_length = ALIGN(mdp->rx_buf_sz, 16);
if (mdp->rx_skbuff[entry] == NULL) {
- skb = netdev_alloc_skb(ndev, mdp->rx_buf_sz);
+ skb = netdev_alloc_skb(ndev, skbuff_size);
mdp->rx_skbuff[entry] = skb;
if (skb == NULL)
break; /* Better luck next round. */
- dma_map_single(&ndev->dev, skb->data, mdp->rx_buf_sz,
- DMA_FROM_DEVICE);
sh_eth_set_receive_align(skb);
+ dma_map_single(&ndev->dev, skb->data,
+ rxdesc->buffer_length, DMA_FROM_DEVICE);
skb_checksum_none_assert(skb);
rxdesc->addr = virt_to_phys(PTR_ALIGN(skb->data, 4));
if (ret)
goto out_free_irq;
+ mdp->is_opened = 1;
+
return ret;
out_free_irq:
return NETDEV_TX_OK;
}
+static struct net_device_stats *sh_eth_get_stats(struct net_device *ndev)
+{
+ struct sh_eth_private *mdp = netdev_priv(ndev);
+
+ if (sh_eth_is_rz_fast_ether(mdp))
+ return &ndev->stats;
+
+ if (!mdp->is_opened)
+ return &ndev->stats;
+
+ ndev->stats.tx_dropped += sh_eth_read(ndev, TROCR);
+ sh_eth_write(ndev, 0, TROCR); /* (write clear) */
+ ndev->stats.collisions += sh_eth_read(ndev, CDCR);
+ sh_eth_write(ndev, 0, CDCR); /* (write clear) */
+ ndev->stats.tx_carrier_errors += sh_eth_read(ndev, LCCR);
+ sh_eth_write(ndev, 0, LCCR); /* (write clear) */
+
+ if (sh_eth_is_gether(mdp)) {
+ ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CERCR);
+ sh_eth_write(ndev, 0, CERCR); /* (write clear) */
+ ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CEECR);
+ sh_eth_write(ndev, 0, CEECR); /* (write clear) */
+ } else {
+ ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CNDCR);
+ sh_eth_write(ndev, 0, CNDCR); /* (write clear) */
+ }
+
+ return &ndev->stats;
+}
+
/* device close function */
static int sh_eth_close(struct net_device *ndev)
{
sh_eth_write(ndev, 0, EDTRR);
sh_eth_write(ndev, 0, EDRRR);
+ sh_eth_get_stats(ndev);
/* PHY Disconnect */
if (mdp->phydev) {
phy_stop(mdp->phydev);
pm_runtime_put_sync(&mdp->pdev->dev);
- return 0;
-}
-
-static struct net_device_stats *sh_eth_get_stats(struct net_device *ndev)
-{
- struct sh_eth_private *mdp = netdev_priv(ndev);
-
- if (sh_eth_is_rz_fast_ether(mdp))
- return &ndev->stats;
+ mdp->is_opened = 0;
- pm_runtime_get_sync(&mdp->pdev->dev);
-
- ndev->stats.tx_dropped += sh_eth_read(ndev, TROCR);
- sh_eth_write(ndev, 0, TROCR); /* (write clear) */
- ndev->stats.collisions += sh_eth_read(ndev, CDCR);
- sh_eth_write(ndev, 0, CDCR); /* (write clear) */
- ndev->stats.tx_carrier_errors += sh_eth_read(ndev, LCCR);
- sh_eth_write(ndev, 0, LCCR); /* (write clear) */
- if (sh_eth_is_gether(mdp)) {
- ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CERCR);
- sh_eth_write(ndev, 0, CERCR); /* (write clear) */
- ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CEECR);
- sh_eth_write(ndev, 0, CEECR); /* (write clear) */
- } else {
- ndev->stats.tx_carrier_errors += sh_eth_read(ndev, CNDCR);
- sh_eth_write(ndev, 0, CNDCR); /* (write clear) */
- }
- pm_runtime_put_sync(&mdp->pdev->dev);
-
- return &ndev->stats;
+ return 0;
}
/* ioctl to device function */
/* Driver's parameters */
#if defined(CONFIG_CPU_SH4) || defined(CONFIG_ARCH_SHMOBILE)
-#define SH4_SKB_RX_ALIGN 32
+#define SH_ETH_RX_ALIGN 32
#else
-#define SH2_SH3_SKB_RX_ALIGN 2
+#define SH_ETH_RX_ALIGN 2
#endif
/* Register's bits
unsigned no_ether_link:1;
unsigned ether_link_active_low:1;
+ unsigned is_opened:1;
};
static inline void sh_eth_soft_swap(char *src, int len)
plat_dat = dev_get_platdata(&pdev->dev);
+ if (!plat_dat)
+ plat_dat = devm_kzalloc(&pdev->dev,
+ sizeof(struct plat_stmmacenet_data),
+ GFP_KERNEL);
+ if (!plat_dat) {
+ pr_err("%s: ERROR: no memory", __func__);
+ return -ENOMEM;
+ }
+
/* Set default value for multicast hash bins */
plat_dat->multicast_filter_bins = HASH_TABLE_SIZE;
plat_dat->unicast_filter_entries = 1;
if (pdev->dev.of_node) {
- if (!plat_dat)
- plat_dat = devm_kzalloc(&pdev->dev,
- sizeof(struct plat_stmmacenet_data),
- GFP_KERNEL);
- if (!plat_dat) {
- pr_err("%s: ERROR: no memory", __func__);
- return -ENOMEM;
- }
-
ret = stmmac_probe_config_dt(pdev, plat_dat, &mac);
if (ret) {
pr_err("%s: main dt probe failed", __func__);
len = skb_frag_size(frag);
offset = frag->page_offset;
- /* Data must not cross a page boundary. */
- BUG_ON(len + offset > PAGE_SIZE<<compound_order(page));
-
/* Skip unused frames from start of page */
page += offset >> PAGE_SHIFT;
offset &= ~PAGE_MASK;
while (len > 0) {
unsigned long bytes;
- BUG_ON(offset >= PAGE_SIZE);
-
bytes = PAGE_SIZE - offset;
if (bytes > len)
bytes = len;
int __init __weak early_init_dt_reserve_memory_arch(phys_addr_t base,
phys_addr_t size, bool nomap)
{
- if (memblock_is_region_reserved(base, size))
- return -EBUSY;
if (nomap)
return memblock_remove(base, size);
return memblock_reserve(base, size);
struct resource all;
struct resource io;
+ struct resource pio;
struct resource mem;
struct resource prefetch;
struct resource busn;
{
struct tegra_pcie *pcie = sys_to_pcie(sys);
int err;
- phys_addr_t io_start;
err = devm_request_resource(pcie->dev, &pcie->all, &pcie->mem);
if (err < 0)
if (err)
return err;
- io_start = pci_pio_to_address(pcie->io.start);
-
pci_add_resource_offset(&sys->resources, &pcie->mem, sys->mem_offset);
pci_add_resource_offset(&sys->resources, &pcie->prefetch,
sys->mem_offset);
pci_add_resource(&sys->resources, &pcie->busn);
- pci_ioremap_io(nr * SZ_64K, io_start);
+ pci_ioremap_io(pcie->pio.start, pcie->io.start);
return 1;
}
static void tegra_pcie_setup_translations(struct tegra_pcie *pcie)
{
u32 fpci_bar, size, axi_address;
- phys_addr_t io_start = pci_pio_to_address(pcie->io.start);
/* Bar 0: type 1 extended configuration space */
fpci_bar = 0xfe100000;
/* Bar 1: downstream IO bar */
fpci_bar = 0xfdfc0000;
size = resource_size(&pcie->io);
- axi_address = io_start;
+ axi_address = pcie->io.start;
afi_writel(pcie, axi_address, AFI_AXI_BAR1_START);
afi_writel(pcie, size >> 12, AFI_AXI_BAR1_SZ);
afi_writel(pcie, fpci_bar, AFI_FPCI_BAR1);
switch (res.flags & IORESOURCE_TYPE_BITS) {
case IORESOURCE_IO:
- memcpy(&pcie->io, &res, sizeof(res));
- pcie->io.name = np->full_name;
+ memcpy(&pcie->pio, &res, sizeof(res));
+ pcie->pio.name = np->full_name;
+
+ /*
+ * The Tegra PCIe host bridge uses this to program the
+ * mapping of the I/O space to the physical address,
+ * so we override the .start and .end fields here that
+ * of_pci_range_to_resource() converted to I/O space.
+ * We also set the IORESOURCE_MEM type to clarify that
+ * the resource is in the physical memory space.
+ */
+ pcie->io.start = range.cpu_addr;
+ pcie->io.end = range.cpu_addr + range.size - 1;
+ pcie->io.flags = IORESOURCE_MEM;
+ pcie->io.name = "I/O";
+
+ memcpy(&res, &pcie->io, sizeof(res));
break;
case IORESOURCE_MEM:
via I2C bus. S2MPA01 has 10 Bucks and 26 LDO outputs.
config REGULATOR_S2MPS11
- tristate "Samsung S2MPS11/S2MPS14/S2MPU02 voltage regulator"
+ tristate "Samsung S2MPS11/S2MPS13/S2MPS14/S2MPU02 voltage regulator"
depends on MFD_SEC_CORE
help
- This driver supports a Samsung S2MPS11/S2MPS14/S2MPU02 voltage output
- regulator via I2C bus. The chip is comprised of high efficient Buck
- converters including Dual-Phase Buck converter, Buck-Boost converter,
- various LDOs.
+ This driver supports a Samsung S2MPS11/S2MPS13/S2MPS14/S2MPU02 voltage
+ output regulator via I2C bus. The chip is comprised of high efficient
+ Buck converters including Dual-Phase Buck converter, Buck-Boost
+ converter, various LDOs.
config REGULATOR_S5M8767
tristate "Samsung S5M8767A voltage regulator"
#include <linux/of_gpio.h>
#include <linux/mfd/samsung/core.h>
#include <linux/mfd/samsung/s2mps11.h>
+#include <linux/mfd/samsung/s2mps13.h>
#include <linux/mfd/samsung/s2mps14.h>
#include <linux/mfd/samsung/s2mpu02.h>
enum sec_device_type dev_type;
/*
- * One bit for each S2MPS14/S2MPU02 regulator whether the suspend mode
- * was enabled.
+ * One bit for each S2MPS13/S2MPS14/S2MPU02 regulator whether
+ * the suspend mode was enabled.
*/
- unsigned long long s2mps14_suspend_state:35;
+ unsigned long long s2mps14_suspend_state:50;
/* Array of size rdev_num with GPIO-s for external sleep control */
int *ext_control_gpio;
regulator_desc_s2mps11_buck6_10(10, MIN_750_MV, STEP_12_5_MV),
};
+static struct regulator_ops s2mps14_reg_ops;
+
+#define regulator_desc_s2mps13_ldo(num, min, step, min_sel) { \
+ .name = "LDO"#num, \
+ .id = S2MPS13_LDO##num, \
+ .ops = &s2mps14_reg_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = min, \
+ .uV_step = step, \
+ .linear_min_sel = min_sel, \
+ .n_voltages = S2MPS14_LDO_N_VOLTAGES, \
+ .vsel_reg = S2MPS13_REG_L1CTRL + num - 1, \
+ .vsel_mask = S2MPS14_LDO_VSEL_MASK, \
+ .enable_reg = S2MPS13_REG_L1CTRL + num - 1, \
+ .enable_mask = S2MPS14_ENABLE_MASK \
+}
+
+#define regulator_desc_s2mps13_buck(num, min, step, min_sel) { \
+ .name = "BUCK"#num, \
+ .id = S2MPS13_BUCK##num, \
+ .ops = &s2mps14_reg_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = min, \
+ .uV_step = step, \
+ .linear_min_sel = min_sel, \
+ .n_voltages = S2MPS14_BUCK_N_VOLTAGES, \
+ .ramp_delay = S2MPS13_BUCK_RAMP_DELAY, \
+ .vsel_reg = S2MPS13_REG_B1OUT + (num - 1) * 2, \
+ .vsel_mask = S2MPS14_BUCK_VSEL_MASK, \
+ .enable_reg = S2MPS13_REG_B1CTRL + (num - 1) * 2, \
+ .enable_mask = S2MPS14_ENABLE_MASK \
+}
+
+static const struct regulator_desc s2mps13_regulators[] = {
+ regulator_desc_s2mps13_ldo(1, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(2, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(3, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(4, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(5, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(6, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(7, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(8, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(9, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(10, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(11, MIN_800_MV, STEP_25_MV, 0x10),
+ regulator_desc_s2mps13_ldo(12, MIN_800_MV, STEP_25_MV, 0x10),
+ regulator_desc_s2mps13_ldo(13, MIN_800_MV, STEP_25_MV, 0x10),
+ regulator_desc_s2mps13_ldo(14, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(15, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(16, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(17, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(18, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(19, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(20, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(21, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(22, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(23, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(24, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(25, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(26, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(27, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(28, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(29, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(30, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(31, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(32, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(33, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(34, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(35, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(36, MIN_800_MV, STEP_12_5_MV, 0x00),
+ regulator_desc_s2mps13_ldo(37, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(38, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_ldo(39, MIN_1000_MV, STEP_25_MV, 0x08),
+ regulator_desc_s2mps13_ldo(40, MIN_1400_MV, STEP_50_MV, 0x0C),
+ regulator_desc_s2mps13_buck(1, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(2, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(3, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(4, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(5, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(6, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(7, MIN_500_MV, STEP_6_25_MV, 0x10),
+ regulator_desc_s2mps13_buck(8, MIN_1000_MV, STEP_12_5_MV, 0x20),
+ regulator_desc_s2mps13_buck(9, MIN_1000_MV, STEP_12_5_MV, 0x20),
+ regulator_desc_s2mps13_buck(10, MIN_500_MV, STEP_6_25_MV, 0x10),
+};
+
static int s2mps14_regulator_enable(struct regulator_dev *rdev)
{
struct s2mps11_info *s2mps11 = rdev_get_drvdata(rdev);
unsigned int val;
switch (s2mps11->dev_type) {
+ case S2MPS13X:
case S2MPS14X:
if (s2mps11->s2mps14_suspend_state & (1 << rdev_get_id(rdev)))
val = S2MPS14_ENABLE_SUSPEND;
/* Below LDO should be always on or does not support suspend mode. */
switch (s2mps11->dev_type) {
+ case S2MPS13X:
case S2MPS14X:
switch (rdev_id) {
case S2MPS14_LDO3:
s2mps11->rdev_num = ARRAY_SIZE(s2mps11_regulators);
regulators = s2mps11_regulators;
break;
+ case S2MPS13X:
+ s2mps11->rdev_num = ARRAY_SIZE(s2mps13_regulators);
+ regulators = s2mps13_regulators;
+ break;
case S2MPS14X:
s2mps11->rdev_num = ARRAY_SIZE(s2mps14_regulators);
regulators = s2mps14_regulators;
static const struct platform_device_id s2mps11_pmic_id[] = {
{ "s2mps11-pmic", S2MPS11X},
+ { "s2mps13-pmic", S2MPS13X},
{ "s2mps14-pmic", S2MPS14X},
{ "s2mpu02-pmic", S2MPU02},
{ },
static const struct s3c2410_wdt_variant drv_data_exynos7 = {
.disable_reg = EXYNOS5_WDT_DISABLE_REG_OFFSET,
.mask_reset_reg = EXYNOS5_WDT_MASK_RESET_REG_OFFSET,
- .mask_bit = 0,
+ .mask_bit = 23,
.rst_stat_reg = EXYNOS5_RST_STAT_REG_OFFSET,
.rst_stat_bit = 23, /* A57 WDTRESET */
.quirks = QUIRK_HAS_PMU_CONFIG | QUIRK_HAS_RST_STAT,
}
alias = d_find_alias(inode);
- if (alias && !vfat_d_anon_disconn(alias)) {
+ /*
+ * Checking "alias->d_parent == dentry->d_parent" to make sure
+ * FS is not corrupted (especially double linked dir).
+ */
+ if (alias && alias->d_parent == dentry->d_parent &&
+ !vfat_d_anon_disconn(alias)) {
/*
* This inode has non anonymous-DCACHE_DISCONNECTED
* dentry. This means, the user did ->lookup() by an
out:
mutex_unlock(&MSDOS_SB(sb)->s_lock);
- dentry->d_time = dentry->d_parent->d_inode->i_version;
- dentry = d_splice_alias(inode, dentry);
- if (dentry)
- dentry->d_time = dentry->d_parent->d_inode->i_version;
- return dentry;
-
+ if (!inode)
+ dentry->d_time = dir->i_version;
+ return d_splice_alias(inode, dentry);
error:
mutex_unlock(&MSDOS_SB(sb)->s_lock);
return ERR_PTR(err);
inode->i_mtime = inode->i_atime = inode->i_ctime = ts;
/* timestamp is already written, so mark_inode_dirty() is unneeded. */
- dentry->d_time = dentry->d_parent->d_inode->i_version;
d_instantiate(dentry, inode);
out:
mutex_unlock(&MSDOS_SB(sb)->s_lock);
clear_nlink(inode);
inode->i_mtime = inode->i_atime = CURRENT_TIME_SEC;
fat_detach(inode);
+ dentry->d_time = dir->i_version;
out:
mutex_unlock(&MSDOS_SB(sb)->s_lock);
clear_nlink(inode);
inode->i_mtime = inode->i_atime = CURRENT_TIME_SEC;
fat_detach(inode);
+ dentry->d_time = dir->i_version;
out:
mutex_unlock(&MSDOS_SB(sb)->s_lock);
inode->i_mtime = inode->i_atime = inode->i_ctime = ts;
/* timestamp is already written, so mark_inode_dirty() is unneeded. */
- dentry->d_time = dentry->d_parent->d_inode->i_version;
d_instantiate(dentry, inode);
mutex_unlock(&MSDOS_SB(sb)->s_lock);
journal->j_chksum_driver = NULL;
return 0;
}
- }
- /* Precompute checksum seed for all metadata */
- if (jbd2_journal_has_csum_v2or3(journal))
+ /* Precompute checksum seed for all metadata */
journal->j_csum_seed = jbd2_chksum(journal, ~0,
sb->s_uuid,
sizeof(sb->s_uuid));
+ }
}
/* If enabling v1 checksums, downgrade superblock */
* @detect_pin: GPIO pin wired to the card detect switch
* @wp_pin: GPIO pin wired to the write protect sensor
* @detect_is_active_high: The state of the detect pin when it is active
+ * @non_removable: The slot is not removable, only detect once
*
* If a given slot is not present on the board, @bus_width should be
* set to 0. The other fields are ignored in this case.
int detect_pin;
int wp_pin;
bool detect_is_active_high;
+ bool non_removable;
};
/**
* @MEM_DDR3: DDR3 RAM
* @MEM_RDDR3: Registered DDR3 RAM
* This is a variant of the DDR3 memories.
- * @MEM_DDR4: DDR4 RAM
+ * @MEM_LRDDR3 Load-Reduced DDR3 memory.
+ * @MEM_DDR4: Unbuffered DDR4 RAM
* @MEM_RDDR4: Registered DDR4 RAM
* This is a variant of the DDR4 memories.
*/
MEM_XDR,
MEM_DDR3,
MEM_RDDR3,
+ MEM_LRDDR3,
MEM_DDR4,
MEM_RDDR4,
};
int ab8500_sysctrl_read(u16 reg, u8 *value);
int ab8500_sysctrl_write(u16 reg, u8 mask, u8 value);
-void ab8500_restart(char mode, const char *cmd);
#else
#define ARIZONA_MIC_BIAS_CTRL_1 0x218
#define ARIZONA_MIC_BIAS_CTRL_2 0x219
#define ARIZONA_MIC_BIAS_CTRL_3 0x21A
+#define ARIZONA_HP_CTRL_1L 0x225
+#define ARIZONA_HP_CTRL_1R 0x226
#define ARIZONA_ACCESSORY_DETECT_MODE_1 0x293
#define ARIZONA_HEADPHONE_DETECT_1 0x29B
#define ARIZONA_HEADPHONE_DETECT_2 0x29C
#define ARIZONA_AIF2_FRAME_CTRL_2 0x548
#define ARIZONA_AIF2_FRAME_CTRL_3 0x549
#define ARIZONA_AIF2_FRAME_CTRL_4 0x54A
+#define ARIZONA_AIF2_FRAME_CTRL_5 0x54B
+#define ARIZONA_AIF2_FRAME_CTRL_6 0x54C
+#define ARIZONA_AIF2_FRAME_CTRL_7 0x54D
+#define ARIZONA_AIF2_FRAME_CTRL_8 0x54E
#define ARIZONA_AIF2_FRAME_CTRL_11 0x551
#define ARIZONA_AIF2_FRAME_CTRL_12 0x552
+#define ARIZONA_AIF2_FRAME_CTRL_13 0x553
+#define ARIZONA_AIF2_FRAME_CTRL_14 0x554
+#define ARIZONA_AIF2_FRAME_CTRL_15 0x555
+#define ARIZONA_AIF2_FRAME_CTRL_16 0x556
#define ARIZONA_AIF2_TX_ENABLES 0x559
#define ARIZONA_AIF2_RX_ENABLES 0x55A
#define ARIZONA_AIF2_FORCE_WRITE 0x55B
#define ARIZONA_MICB3_ENA_SHIFT 0 /* MICB3_ENA */
#define ARIZONA_MICB3_ENA_WIDTH 1 /* MICB3_ENA */
+/*
+ * R549 (0x225) - HP Ctrl 1L
+ */
+#define ARIZONA_RMV_SHRT_HP1L 0x4000 /* RMV_SHRT_HP1L */
+#define ARIZONA_RMV_SHRT_HP1L_MASK 0x4000 /* RMV_SHRT_HP1L */
+#define ARIZONA_RMV_SHRT_HP1L_SHIFT 14 /* RMV_SHRT_HP1L */
+#define ARIZONA_RMV_SHRT_HP1L_WIDTH 1 /* RMV_SHRT_HP1L */
+#define ARIZONA_HP1L_FLWR 0x0004 /* HP1L_FLWR */
+#define ARIZONA_HP1L_FLWR_MASK 0x0004 /* HP1L_FLWR */
+#define ARIZONA_HP1L_FLWR_SHIFT 2 /* HP1L_FLWR */
+#define ARIZONA_HP1L_FLWR_WIDTH 1 /* HP1L_FLWR */
+#define ARIZONA_HP1L_SHRTI 0x0002 /* HP1L_SHRTI */
+#define ARIZONA_HP1L_SHRTI_MASK 0x0002 /* HP1L_SHRTI */
+#define ARIZONA_HP1L_SHRTI_SHIFT 1 /* HP1L_SHRTI */
+#define ARIZONA_HP1L_SHRTI_WIDTH 1 /* HP1L_SHRTI */
+#define ARIZONA_HP1L_SHRTO 0x0001 /* HP1L_SHRTO */
+#define ARIZONA_HP1L_SHRTO_MASK 0x0001 /* HP1L_SHRTO */
+#define ARIZONA_HP1L_SHRTO_SHIFT 0 /* HP1L_SHRTO */
+#define ARIZONA_HP1L_SHRTO_WIDTH 1 /* HP1L_SHRTO */
+
+/*
+ * R550 (0x226) - HP Ctrl 1R
+ */
+#define ARIZONA_RMV_SHRT_HP1R 0x4000 /* RMV_SHRT_HP1R */
+#define ARIZONA_RMV_SHRT_HP1R_MASK 0x4000 /* RMV_SHRT_HP1R */
+#define ARIZONA_RMV_SHRT_HP1R_SHIFT 14 /* RMV_SHRT_HP1R */
+#define ARIZONA_RMV_SHRT_HP1R_WIDTH 1 /* RMV_SHRT_HP1R */
+#define ARIZONA_HP1R_FLWR 0x0004 /* HP1R_FLWR */
+#define ARIZONA_HP1R_FLWR_MASK 0x0004 /* HP1R_FLWR */
+#define ARIZONA_HP1R_FLWR_SHIFT 2 /* HP1R_FLWR */
+#define ARIZONA_HP1R_FLWR_WIDTH 1 /* HP1R_FLWR */
+#define ARIZONA_HP1R_SHRTI 0x0002 /* HP1R_SHRTI */
+#define ARIZONA_HP1R_SHRTI_MASK 0x0002 /* HP1R_SHRTI */
+#define ARIZONA_HP1R_SHRTI_SHIFT 1 /* HP1R_SHRTI */
+#define ARIZONA_HP1R_SHRTI_WIDTH 1 /* HP1R_SHRTI */
+#define ARIZONA_HP1R_SHRTO 0x0001 /* HP1R_SHRTO */
+#define ARIZONA_HP1R_SHRTO_MASK 0x0001 /* HP1R_SHRTO */
+#define ARIZONA_HP1R_SHRTO_SHIFT 0 /* HP1R_SHRTO */
+#define ARIZONA_HP1R_SHRTO_WIDTH 1 /* HP1R_SHRTO */
+
/*
* R659 (0x293) - Accessory Detect Mode 1
*/
--- /dev/null
+/*
+ * Copyright (C) 2014 Free Electrons
+ * Copyright (C) 2014 Atmel
+ *
+ * Author: Boris BREZILLON <boris.brezillon@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef __LINUX_MFD_HLCDC_H
+#define __LINUX_MFD_HLCDC_H
+
+#include <linux/clk.h>
+#include <linux/regmap.h>
+
+#define ATMEL_HLCDC_CFG(i) ((i) * 0x4)
+#define ATMEL_HLCDC_SIG_CFG LCDCFG(5)
+#define ATMEL_HLCDC_HSPOL BIT(0)
+#define ATMEL_HLCDC_VSPOL BIT(1)
+#define ATMEL_HLCDC_VSPDLYS BIT(2)
+#define ATMEL_HLCDC_VSPDLYE BIT(3)
+#define ATMEL_HLCDC_DISPPOL BIT(4)
+#define ATMEL_HLCDC_DITHER BIT(6)
+#define ATMEL_HLCDC_DISPDLY BIT(7)
+#define ATMEL_HLCDC_MODE_MASK GENMASK(9, 8)
+#define ATMEL_HLCDC_PP BIT(10)
+#define ATMEL_HLCDC_VSPSU BIT(12)
+#define ATMEL_HLCDC_VSPHO BIT(13)
+#define ATMEL_HLCDC_GUARDTIME_MASK GENMASK(20, 16)
+
+#define ATMEL_HLCDC_EN 0x20
+#define ATMEL_HLCDC_DIS 0x24
+#define ATMEL_HLCDC_SR 0x28
+#define ATMEL_HLCDC_IER 0x2c
+#define ATMEL_HLCDC_IDR 0x30
+#define ATMEL_HLCDC_IMR 0x34
+#define ATMEL_HLCDC_ISR 0x38
+
+#define ATMEL_HLCDC_CLKPOL BIT(0)
+#define ATMEL_HLCDC_CLKSEL BIT(2)
+#define ATMEL_HLCDC_CLKPWMSEL BIT(3)
+#define ATMEL_HLCDC_CGDIS(i) BIT(8 + (i))
+#define ATMEL_HLCDC_CLKDIV_SHFT 16
+#define ATMEL_HLCDC_CLKDIV_MASK GENMASK(23, 16)
+#define ATMEL_HLCDC_CLKDIV(div) ((div - 2) << ATMEL_HLCDC_CLKDIV_SHFT)
+
+#define ATMEL_HLCDC_PIXEL_CLK BIT(0)
+#define ATMEL_HLCDC_SYNC BIT(1)
+#define ATMEL_HLCDC_DISP BIT(2)
+#define ATMEL_HLCDC_PWM BIT(3)
+#define ATMEL_HLCDC_SIP BIT(4)
+
+#define ATMEL_HLCDC_SOF BIT(0)
+#define ATMEL_HLCDC_SYNCDIS BIT(1)
+#define ATMEL_HLCDC_FIFOERR BIT(4)
+#define ATMEL_HLCDC_LAYER_STATUS(x) BIT((x) + 8)
+
+/**
+ * Structure shared by the MFD device and its subdevices.
+ *
+ * @regmap: register map used to access HLCDC IP registers
+ * @periph_clk: the hlcdc peripheral clock
+ * @sys_clk: the hlcdc system clock
+ * @slow_clk: the system slow clk
+ * @irq: the hlcdc irq
+ */
+struct atmel_hlcdc {
+ struct regmap *regmap;
+ struct clk *periph_clk;
+ struct clk *sys_clk;
+ struct clk *slow_clk;
+ int irq;
+};
+
+#endif /* __LINUX_MFD_HLCDC_H */
enum {
AXP202_ID = 0,
AXP209_ID,
+ AXP288_ID,
+ NR_AXP20X_VARIANTS,
};
#define AXP20X_DATACACHE(m) (0x04 + (m))
#define AXP20X_IRQ3_EN 0x42
#define AXP20X_IRQ4_EN 0x43
#define AXP20X_IRQ5_EN 0x44
+#define AXP20X_IRQ6_EN 0x45
#define AXP20X_IRQ1_STATE 0x48
#define AXP20X_IRQ2_STATE 0x49
#define AXP20X_IRQ3_STATE 0x4a
#define AXP20X_IRQ4_STATE 0x4b
#define AXP20X_IRQ5_STATE 0x4c
+#define AXP20X_IRQ6_STATE 0x4d
/* ADC */
#define AXP20X_ACIN_V_ADC_H 0x56
#define AXP20X_CC_CTRL 0xb8
#define AXP20X_FG_RES 0xb9
+/* AXP288 specific registers */
+#define AXP288_PMIC_ADC_H 0x56
+#define AXP288_PMIC_ADC_L 0x57
+#define AXP288_ADC_TS_PIN_CTRL 0x84
+
+#define AXP288_PMIC_ADC_EN 0x84
+#define AXP288_FG_TUNE5 0xed
+
+
/* Regulators IDs */
enum {
AXP20X_LDO1 = 0,
AXP20X_IRQ_GPIO0_INPUT,
};
+enum axp288_irqs {
+ AXP288_IRQ_VBUS_FALL = 2,
+ AXP288_IRQ_VBUS_RISE,
+ AXP288_IRQ_OV,
+ AXP288_IRQ_FALLING_ALT,
+ AXP288_IRQ_RISING_ALT,
+ AXP288_IRQ_OV_ALT,
+ AXP288_IRQ_DONE = 10,
+ AXP288_IRQ_CHARGING,
+ AXP288_IRQ_SAFE_QUIT,
+ AXP288_IRQ_SAFE_ENTER,
+ AXP288_IRQ_ABSENT,
+ AXP288_IRQ_APPEND,
+ AXP288_IRQ_QWBTU,
+ AXP288_IRQ_WBTU,
+ AXP288_IRQ_QWBTO,
+ AXP288_IRQ_WBTO,
+ AXP288_IRQ_QCBTU,
+ AXP288_IRQ_CBTU,
+ AXP288_IRQ_QCBTO,
+ AXP288_IRQ_CBTO,
+ AXP288_IRQ_WL2,
+ AXP288_IRQ_WL1,
+ AXP288_IRQ_GPADC,
+ AXP288_IRQ_OT = 31,
+ AXP288_IRQ_GPIO0,
+ AXP288_IRQ_GPIO1,
+ AXP288_IRQ_POKO,
+ AXP288_IRQ_POKL,
+ AXP288_IRQ_POKS,
+ AXP288_IRQ_POKN,
+ AXP288_IRQ_POKP,
+ AXP288_IRQ_TIMER,
+ AXP288_IRQ_MV_CHNG,
+ AXP288_IRQ_BC_USB_CHNG,
+};
+
+#define AXP288_TS_ADC_H 0x58
+#define AXP288_TS_ADC_L 0x59
+#define AXP288_GP_ADC_H 0x5a
+#define AXP288_GP_ADC_L 0x5b
+
struct axp20x_dev {
struct device *dev;
struct i2c_client *i2c_client;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irqc;
long variant;
+ int nr_cells;
+ struct mfd_cell *cells;
+ const struct regmap_config *regmap_cfg;
+ const struct regmap_irq_chip *regmap_irq_chip;
};
#endif /* __LINUX_MFD_AXP20X_H */
struct resource *mem_base,
int irq_base, struct irq_domain *irq_domain);
+static inline int mfd_add_hotplug_devices(struct device *parent,
+ const struct mfd_cell *cells, int n_devs)
+{
+ return mfd_add_devices(parent, PLATFORM_DEVID_AUTO, cells, n_devs,
+ NULL, 0, NULL);
+}
+
extern void mfd_remove_devices(struct device *parent);
#endif
--- /dev/null
+#ifndef __LINUX_USB_DLN2_H
+#define __LINUX_USB_DLN2_H
+
+#define DLN2_CMD(cmd, id) ((cmd) | ((id) << 8))
+
+struct dln2_platform_data {
+ u16 handle; /* sub-driver handle (internally used only) */
+ u8 port; /* I2C/SPI port */
+};
+
+/**
+ * dln2_event_cb_t - event callback function signature
+ *
+ * @pdev - the sub-device that registered this callback
+ * @echo - the echo header field received in the message
+ * @data - the data payload
+ * @len - the data payload length
+ *
+ * The callback function is called in interrupt context and the data payload is
+ * only valid during the call. If the user needs later access of the data, it
+ * must copy it.
+ */
+
+typedef void (*dln2_event_cb_t)(struct platform_device *pdev, u16 echo,
+ const void *data, int len);
+
+/**
+ * dl2n_register_event_cb - register a callback function for an event
+ *
+ * @pdev - the sub-device that registers the callback
+ * @event - the event for which to register a callback
+ * @event_cb - the callback function
+ *
+ * @return 0 in case of success, negative value in case of error
+ */
+int dln2_register_event_cb(struct platform_device *pdev, u16 event,
+ dln2_event_cb_t event_cb);
+
+/**
+ * dln2_unregister_event_cb - unregister the callback function for an event
+ *
+ * @pdev - the sub-device that registered the callback
+ * @event - the event for which to register a callback
+ */
+void dln2_unregister_event_cb(struct platform_device *pdev, u16 event);
+
+/**
+ * dln2_transfer - issue a DLN2 command and wait for a response and the
+ * associated data
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the user
+ * doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ * @ibuf - any data associated with the response will be copied here; it can be
+ * NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will be modified
+ * to indicate the actual data transferred;
+ *
+ * @return 0 for success, negative value for errors
+ */
+int dln2_transfer(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len,
+ void *ibuf, unsigned *ibuf_len);
+
+/**
+ * dln2_transfer_rx - variant of @dln2_transfer() where TX buffer is not needed
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @ibuf - any data associated with the response will be copied here; it can be
+ * NULL if the user doesn't need the response data
+ * @ibuf_len - must be initialized to the input buffer size; it will be modified
+ * to indicate the actual data transferred;
+ *
+ * @return 0 for success, negative value for errors
+ */
+
+static inline int dln2_transfer_rx(struct platform_device *pdev, u16 cmd,
+ void *ibuf, unsigned *ibuf_len)
+{
+ return dln2_transfer(pdev, cmd, NULL, 0, ibuf, ibuf_len);
+}
+
+/**
+ * dln2_transfer_tx - variant of @dln2_transfer() where RX buffer is not needed
+ *
+ * @pdev - the sub-device which is issuing this transfer
+ * @cmd - the command to be sent to the device
+ * @obuf - the buffer to be sent to the device; it can be NULL if the
+ * user doesn't need to transmit data with this command
+ * @obuf_len - the size of the buffer to be sent to the device
+ *
+ * @return 0 for success, negative value for errors
+ */
+static inline int dln2_transfer_tx(struct platform_device *pdev, u16 cmd,
+ const void *obuf, unsigned obuf_len)
+{
+ return dln2_transfer(pdev, cmd, obuf, obuf_len, NULL, NULL);
+}
+
+#endif
#include <linux/i2c.h>
-#define MAX77693_NUM_IRQ_MUIC_REGS 3
#define MAX77693_REG_INVALID (0xff)
/* Slave addr = 0xCC: PMIC, Charger, Flash LED */
#define SD_SAMPLE_POINT_CTL 0xFDA7
#define SD_PUSH_POINT_CTL 0xFDA8
#define SD_CMD0 0xFDA9
+#define SD_CMD_START 0x40
#define SD_CMD1 0xFDAA
#define SD_CMD2 0xFDAB
#define SD_CMD3 0xFDAC
#define PM_CTRL1 0xFF44
#define PM_CTRL2 0xFF45
#define PM_CTRL3 0xFF46
+#define SDIO_SEND_PME_EN 0x80
+#define FORCE_RC_MODE_ON 0x40
+#define FORCE_RX50_LINK_ON 0x20
+#define D3_DELINK_MODE_EN 0x10
+#define USE_PESRTB_CTL_DELINK 0x08
+#define DELAY_PIN_WAKE 0x04
+#define RESET_PIN_WAKE 0x02
+#define PM_WAKE_EN 0x01
#define PM_CTRL4 0xFF47
/* Memory mapping */
#define PHY_DUM_REG 0x1F
#define LCTLR 0x80
+#define LCTLR_EXT_SYNC 0x80
+#define LCTLR_COMMON_CLOCK_CFG 0x40
+#define LCTLR_RETRAIN_LINK 0x20
+#define LCTLR_LINK_DISABLE 0x10
+#define LCTLR_RCB 0x08
+#define LCTLR_RESERVED 0x04
+#define LCTLR_ASPM_CTL_MASK 0x03
+
#define PCR_SETTING_REG1 0x724
#define PCR_SETTING_REG2 0x814
#define PCR_SETTING_REG3 0x747
return (u8 *)(pcr->host_cmds_ptr);
}
+static inline int rtsx_pci_update_cfg_byte(struct rtsx_pcr *pcr, int addr,
+ u8 mask, u8 append)
+{
+ int err;
+ u8 val;
+
+ err = pci_read_config_byte(pcr->pci, addr, &val);
+ if (err < 0)
+ return err;
+ return pci_write_config_byte(pcr->pci, addr, (val & mask) | append);
+}
+
+static inline void rtsx_pci_write_be32(struct rtsx_pcr *pcr, u16 reg, u32 val)
+{
+ rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg, 0xFF, val >> 24);
+ rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 1, 0xFF, val >> 16);
+ rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 2, 0xFF, val >> 8);
+ rtsx_pci_add_cmd(pcr, WRITE_REG_CMD, reg + 3, 0xFF, val);
+}
+
#endif
#define MIN_800_MV 800000
#define MIN_750_MV 750000
#define MIN_600_MV 600000
+#define MIN_500_MV 500000
/* Macros to represent steps for LDO/BUCK */
#define STEP_50_MV 50000
S5M8767X,
S2MPA01,
S2MPS11X,
+ S2MPS13X,
S2MPS14X,
S2MPU02,
};
--- /dev/null
+/*
+ * s2mps13.h
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#ifndef __LINUX_MFD_S2MPS13_H
+#define __LINUX_MFD_S2MPS13_H
+
+/* S2MPS13 registers */
+enum s2mps13_reg {
+ S2MPS13_REG_ID,
+ S2MPS13_REG_INT1,
+ S2MPS13_REG_INT2,
+ S2MPS13_REG_INT3,
+ S2MPS13_REG_INT1M,
+ S2MPS13_REG_INT2M,
+ S2MPS13_REG_INT3M,
+ S2MPS13_REG_ST1,
+ S2MPS13_REG_ST2,
+ S2MPS13_REG_PWRONSRC,
+ S2MPS13_REG_OFFSRC,
+ S2MPS13_REG_BU_CHG,
+ S2MPS13_REG_RTCCTRL,
+ S2MPS13_REG_CTRL1,
+ S2MPS13_REG_CTRL2,
+ S2MPS13_REG_RSVD1,
+ S2MPS13_REG_RSVD2,
+ S2MPS13_REG_RSVD3,
+ S2MPS13_REG_RSVD4,
+ S2MPS13_REG_RSVD5,
+ S2MPS13_REG_RSVD6,
+ S2MPS13_REG_CTRL3,
+ S2MPS13_REG_RSVD7,
+ S2MPS13_REG_RSVD8,
+ S2MPS13_REG_WRSTBI,
+ S2MPS13_REG_B1CTRL,
+ S2MPS13_REG_B1OUT,
+ S2MPS13_REG_B2CTRL,
+ S2MPS13_REG_B2OUT,
+ S2MPS13_REG_B3CTRL,
+ S2MPS13_REG_B3OUT,
+ S2MPS13_REG_B4CTRL,
+ S2MPS13_REG_B4OUT,
+ S2MPS13_REG_B5CTRL,
+ S2MPS13_REG_B5OUT,
+ S2MPS13_REG_B6CTRL,
+ S2MPS13_REG_B6OUT,
+ S2MPS13_REG_B7CTRL,
+ S2MPS13_REG_B7OUT,
+ S2MPS13_REG_B8CTRL,
+ S2MPS13_REG_B8OUT,
+ S2MPS13_REG_B9CTRL,
+ S2MPS13_REG_B9OUT,
+ S2MPS13_REG_B10CTRL,
+ S2MPS13_REG_B10OUT,
+ S2MPS13_REG_BB1CTRL,
+ S2MPS13_REG_BB1OUT,
+ S2MPS13_REG_BUCK_RAMP1,
+ S2MPS13_REG_BUCK_RAMP2,
+ S2MPS13_REG_LDO_DVS1,
+ S2MPS13_REG_LDO_DVS2,
+ S2MPS13_REG_LDO_DVS3,
+ S2MPS13_REG_B6OUT2,
+ S2MPS13_REG_L1CTRL,
+ S2MPS13_REG_L2CTRL,
+ S2MPS13_REG_L3CTRL,
+ S2MPS13_REG_L4CTRL,
+ S2MPS13_REG_L5CTRL,
+ S2MPS13_REG_L6CTRL,
+ S2MPS13_REG_L7CTRL,
+ S2MPS13_REG_L8CTRL,
+ S2MPS13_REG_L9CTRL,
+ S2MPS13_REG_L10CTRL,
+ S2MPS13_REG_L11CTRL,
+ S2MPS13_REG_L12CTRL,
+ S2MPS13_REG_L13CTRL,
+ S2MPS13_REG_L14CTRL,
+ S2MPS13_REG_L15CTRL,
+ S2MPS13_REG_L16CTRL,
+ S2MPS13_REG_L17CTRL,
+ S2MPS13_REG_L18CTRL,
+ S2MPS13_REG_L19CTRL,
+ S2MPS13_REG_L20CTRL,
+ S2MPS13_REG_L21CTRL,
+ S2MPS13_REG_L22CTRL,
+ S2MPS13_REG_L23CTRL,
+ S2MPS13_REG_L24CTRL,
+ S2MPS13_REG_L25CTRL,
+ S2MPS13_REG_L26CTRL,
+ S2MPS13_REG_L27CTRL,
+ S2MPS13_REG_L28CTRL,
+ S2MPS13_REG_L30CTRL,
+ S2MPS13_REG_L31CTRL,
+ S2MPS13_REG_L32CTRL,
+ S2MPS13_REG_L33CTRL,
+ S2MPS13_REG_L34CTRL,
+ S2MPS13_REG_L35CTRL,
+ S2MPS13_REG_L36CTRL,
+ S2MPS13_REG_L37CTRL,
+ S2MPS13_REG_L38CTRL,
+ S2MPS13_REG_L39CTRL,
+ S2MPS13_REG_L40CTRL,
+ S2MPS13_REG_LDODSCH1,
+ S2MPS13_REG_LDODSCH2,
+ S2MPS13_REG_LDODSCH3,
+ S2MPS13_REG_LDODSCH4,
+ S2MPS13_REG_LDODSCH5,
+};
+
+/* regulator ids */
+enum s2mps13_regulators {
+ S2MPS13_LDO1,
+ S2MPS13_LDO2,
+ S2MPS13_LDO3,
+ S2MPS13_LDO4,
+ S2MPS13_LDO5,
+ S2MPS13_LDO6,
+ S2MPS13_LDO7,
+ S2MPS13_LDO8,
+ S2MPS13_LDO9,
+ S2MPS13_LDO10,
+ S2MPS13_LDO11,
+ S2MPS13_LDO12,
+ S2MPS13_LDO13,
+ S2MPS13_LDO14,
+ S2MPS13_LDO15,
+ S2MPS13_LDO16,
+ S2MPS13_LDO17,
+ S2MPS13_LDO18,
+ S2MPS13_LDO19,
+ S2MPS13_LDO20,
+ S2MPS13_LDO21,
+ S2MPS13_LDO22,
+ S2MPS13_LDO23,
+ S2MPS13_LDO24,
+ S2MPS13_LDO25,
+ S2MPS13_LDO26,
+ S2MPS13_LDO27,
+ S2MPS13_LDO28,
+ S2MPS13_LDO29,
+ S2MPS13_LDO30,
+ S2MPS13_LDO31,
+ S2MPS13_LDO32,
+ S2MPS13_LDO33,
+ S2MPS13_LDO34,
+ S2MPS13_LDO35,
+ S2MPS13_LDO36,
+ S2MPS13_LDO37,
+ S2MPS13_LDO38,
+ S2MPS13_LDO39,
+ S2MPS13_LDO40,
+ S2MPS13_BUCK1,
+ S2MPS13_BUCK2,
+ S2MPS13_BUCK3,
+ S2MPS13_BUCK4,
+ S2MPS13_BUCK5,
+ S2MPS13_BUCK6,
+ S2MPS13_BUCK7,
+ S2MPS13_BUCK8,
+ S2MPS13_BUCK9,
+ S2MPS13_BUCK10,
+
+ S2MPS13_REGULATOR_MAX,
+};
+
+/*
+ * Default ramp delay in uv/us. Datasheet says that ramp delay can be
+ * controlled however it does not specify which register is used for that.
+ * Let's assume that default value will be set.
+ */
+#define S2MPS13_BUCK_RAMP_DELAY 12500
+
+#endif /* __LINUX_MFD_S2MPS13_H */
/**
* struct tc3589x_gpio_platform_data - TC3589x GPIO platform data
- * @gpio_base: first gpio number assigned to TC3589x. A maximum of
- * %TC3589x_NR_GPIOS GPIOs will be allocated.
* @setup: callback for board-specific initialization
* @remove: callback for board-specific teardown
*/
struct tc3589x_gpio_platform_data {
- int gpio_base;
void (*setup)(struct tc3589x *tc3589x, unsigned gpio_base);
void (*remove)(struct tc3589x *tc3589x, unsigned gpio_base);
};
/**
* struct tc3589x_platform_data - TC3589x platform data
* @block: bitmask of blocks to enable (use TC3589x_BLOCK_*)
- * @irq_base: base IRQ number. %TC3589x_NR_IRQS irqs will be used.
* @gpio: GPIO-specific platform data
* @keypad: keypad-specific platform data
*/
struct tc3589x_platform_data {
unsigned int block;
- int irq_base;
struct tc3589x_gpio_platform_data *gpio;
const struct tc3589x_keypad_platform_data *keypad;
};
-#define TC3589x_NR_GPIOS 24
-#define TC3589x_NR_IRQS TC3589x_INT_GPIO(TC3589x_NR_GPIOS)
-
#endif
unsigned int data_tag_unit_size; /* DATA TAG UNIT size */
unsigned int boot_ro_lock; /* ro lock support */
bool boot_ro_lockable;
+ bool ffu_capable; /* Firmware upgrade support */
+#define MMC_FIRMWARE_LEN 8
+ u8 fwrev[MMC_FIRMWARE_LEN]; /* FW version */
u8 raw_exception_status; /* 54 */
u8 raw_partition_support; /* 160 */
u8 raw_rpmb_size_mult; /* 168 */
#define mmc_dev_to_card(d) container_of(d, struct mmc_card, dev)
-#define mmc_list_to_card(l) container_of(l, struct mmc_card, node)
-#define mmc_get_drvdata(c) dev_get_drvdata(&(c)->dev)
-#define mmc_set_drvdata(c,d) dev_set_drvdata(&(c)->dev, d)
-
-/*
- * MMC device driver (e.g., Flash card, I/O card...)
- */
-struct mmc_driver {
- struct device_driver drv;
- int (*probe)(struct mmc_card *);
- void (*remove)(struct mmc_card *);
- int (*suspend)(struct mmc_card *);
- int (*resume)(struct mmc_card *);
- void (*shutdown)(struct mmc_card *);
-};
-
-extern int mmc_register_driver(struct mmc_driver *);
-extern void mmc_unregister_driver(struct mmc_driver *);
+extern int mmc_register_driver(struct device_driver *);
+extern void mmc_unregister_driver(struct device_driver *);
extern void mmc_fixup_device(struct mmc_card *card,
const struct mmc_fixup *table);
extern int __mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int, bool,
bool, bool);
extern int mmc_switch(struct mmc_card *, u8, u8, u8, unsigned int);
-extern int mmc_send_ext_csd(struct mmc_card *card, u8 *ext_csd);
+extern int mmc_send_tuning(struct mmc_host *host);
+extern int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
#define MMC_ERASE_ARG 0x00000000
#define MMC_SECURE_ERASE_ARG 0x80000000
* transfer is in progress.
* @use_dma: Whether DMA channel is initialized or not.
* @using_dma: Whether DMA is in use for the current transfer.
+ * @dma_64bit_address: Whether DMA supports 64-bit address mode or not.
* @sg_dma: Bus address of DMA buffer.
* @sg_cpu: Virtual address of DMA buffer.
* @dma_ops: Pointer to platform-specific DMA callbacks.
* @quirks: Set of quirks that apply to specific versions of the IP.
* @irq_flags: The flags to be passed to request_irq.
* @irq: The irq value to be passed to request_irq.
+ * @sdio_id0: Number of slot0 in the SDIO interrupt registers.
*
* Locking
* =======
struct mmc_command stop_abort;
unsigned int prev_blksz;
unsigned char timing;
- struct workqueue_struct *card_workqueue;
/* DMA interface members*/
int use_dma;
int using_dma;
+ int dma_64bit_address;
dma_addr_t sg_dma;
void *sg_cpu;
u32 stop_cmdr;
u32 dir_status;
struct tasklet_struct tasklet;
- struct work_struct card_work;
unsigned long pending_events;
unsigned long completed_events;
enum dw_mci_state state;
bool vqmmc_enabled;
unsigned long irq_flags; /* IRQ flags */
int irq;
+
+ int sdio_id0;
};
/* DMA ops for Internal/External DMAC interface */
#define MMC_CAP2_HS400_1_2V (1 << 16) /* Can support HS400 1.2V */
#define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \
MMC_CAP2_HS400_1_2V)
+#define MMC_CAP2_HSX00_1_2V (MMC_CAP2_HS200_1_2V_SDR | MMC_CAP2_HS400_1_2V)
#define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
mmc_pm_flag_t pm_caps; /* supported pm features */
#define EXT_CSD_SANITIZE_START 165 /* W */
#define EXT_CSD_WR_REL_PARAM 166 /* RO */
#define EXT_CSD_RPMB_MULT 168 /* RO */
+#define EXT_CSD_FW_CONFIG 169 /* R/W */
#define EXT_CSD_BOOT_WP 173 /* R/W */
#define EXT_CSD_ERASE_GROUP_DEF 175 /* R/W */
#define EXT_CSD_PART_CONFIG 179 /* R/W */
#define EXT_CSD_GENERIC_CMD6_TIME 248 /* RO */
#define EXT_CSD_CACHE_SIZE 249 /* RO, 4 bytes */
#define EXT_CSD_PWR_CL_DDR_200_360 253 /* RO */
+#define EXT_CSD_FIRMWARE_VERSION 254 /* RO, 8 bytes */
+#define EXT_CSD_SUPPORTED_MODE 493 /* RO */
#define EXT_CSD_TAG_UNIT_SIZE 498 /* RO */
#define EXT_CSD_DATA_TAG_SUPPORT 499 /* RO */
#define EXT_CSD_MAX_PACKED_WRITES 500 /* RO */
#define SDHCI_QUIRK2_BROKEN_DDR50 (1<<7)
/* Stop command (CMD12) can set Transfer Complete when not using MMC_RSP_BUSY */
#define SDHCI_QUIRK2_STOP_WITH_TC (1<<8)
+/* Controller does not support 64-bit DMA */
+#define SDHCI_QUIRK2_BROKEN_64_BIT_DMA (1<<9)
+/* need clear transfer mode register before send cmd */
+#define SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD (1<<10)
+/* Capability register bit-63 indicates HS400 support */
+#define SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 (1<<11)
int irq; /* Device IRQ */
void __iomem *ioaddr; /* Mapped address */
#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */
#define SDHCI_SDR104_NEEDS_TUNING (1<<10) /* SDR104/HS200 needs tuning */
#define SDHCI_USING_RETUNING_TIMER (1<<11) /* Host is using a retuning timer for the card */
+#define SDHCI_USE_64_BIT_DMA (1<<12) /* Use 64-bit DMA */
unsigned int version; /* SDHCI spec. version */
int sg_count; /* Mapped sg entries */
- u8 *adma_desc; /* ADMA descriptor table */
- u8 *align_buffer; /* Bounce buffer */
+ void *adma_table; /* ADMA descriptor table */
+ void *align_buffer; /* Bounce buffer */
+
+ size_t adma_table_sz; /* ADMA descriptor table size */
+ size_t align_buffer_sz; /* Bounce buffer size */
dma_addr_t adma_addr; /* Mapped ADMA descr. table */
dma_addr_t align_addr; /* Mapped bounce buffer */
+ unsigned int desc_sz; /* ADMA descriptor size */
+ unsigned int align_sz; /* ADMA alignment */
+ unsigned int align_mask; /* ADMA alignment mask */
+
struct tasklet_struct finish_tasklet; /* Tasklet structures */
struct timer_list timer; /* Timer for timeouts */
struct device_driver drv;
};
-#define to_sdio_driver(d) container_of(d, struct sdio_driver, drv)
-
/**
* SDIO_DEVICE - macro used to describe a specific SDIO device
* @vend: the 16 bit manufacturer code
/* CONFIG_OF_RESOLVE api */
extern int of_resolve_phandles(struct device_node *tree);
+/**
+ * of_system_has_poweroff_source - Tells if poweroff-source is found for device_node
+ * @np: Pointer to the given device_node
+ *
+ * return true if present false otherwise
+ */
+static inline bool of_system_has_poweroff_source(const struct device_node *np)
+{
+ return of_property_read_bool(np, "poweroff-source");
+}
+
#endif /* _LINUX_OF_H */
#define PCI_DEVICE_ID_AMD_15H_M10H_F3 0x1403
#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F3 0x141d
#define PCI_DEVICE_ID_AMD_15H_M30H_NB_F4 0x141e
+#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F3 0x1573
+#define PCI_DEVICE_ID_AMD_15H_M60H_NB_F4 0x1574
#define PCI_DEVICE_ID_AMD_15H_NB_F0 0x1600
#define PCI_DEVICE_ID_AMD_15H_NB_F1 0x1601
#define PCI_DEVICE_ID_AMD_15H_NB_F2 0x1602
--- /dev/null
+/*
+ * MMC definitions for OMAP2
+ *
+ * Copyright (C) 2006 Nokia Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * struct omap_hsmmc_dev_attr.flags possibilities
+ *
+ * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
+ * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
+ * should be set if this is the case. See for example Section 22.5.3
+ * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
+ * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
+ *
+ * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
+ * don't work correctly on some MMC controller instances on some
+ * OMAP3 SoCs; this flag should be set if this is the case. See
+ * for example Advisory 2.1.1.128 "MMC: Multiple Block Read
+ * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
+ * Revision F (October 2010) (SPRZ278F).
+ */
+#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0)
+#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1)
+#define OMAP_HSMMC_SWAKEUP_MISSING BIT(2)
+
+struct omap_hsmmc_dev_attr {
+ u8 flags;
+};
+
+struct mmc_card;
+
+struct omap_hsmmc_platform_data {
+ /* back-link to device */
+ struct device *dev;
+
+ /* set if your board has components or wiring that limits the
+ * maximum frequency on the MMC bus */
+ unsigned int max_freq;
+
+ /* Integrating attributes from the omap_hwmod layer */
+ u8 controller_flags;
+
+ /* Register offset deviation */
+ u16 reg_offset;
+
+ /*
+ * 4/8 wires and any additional host capabilities
+ * need to OR'd all capabilities (ref. linux/mmc/host.h)
+ */
+ u32 caps; /* Used for the MMC driver on 2430 and later */
+ u32 pm_caps; /* PM capabilities of the mmc */
+
+ /* switch pin can be for card detect (default) or card cover */
+ unsigned cover:1;
+
+ /* use the internal clock */
+ unsigned internal_clock:1;
+
+ /* nonremovable e.g. eMMC */
+ unsigned nonremovable:1;
+
+ /* eMMC does not handle power off when not in sleep state */
+ unsigned no_regulator_off_init:1;
+
+ /* we can put the features above into this variable */
+#define HSMMC_HAS_PBIAS (1 << 0)
+#define HSMMC_HAS_UPDATED_RESET (1 << 1)
+#define HSMMC_HAS_HSPE_SUPPORT (1 << 2)
+ unsigned features;
+
+ int switch_pin; /* gpio (card detect) */
+ int gpio_wp; /* gpio (write protect) */
+
+ int (*set_power)(struct device *dev, int power_on, int vdd);
+ void (*remux)(struct device *dev, int power_on);
+ /* Call back before enabling / disabling regulators */
+ void (*before_set_reg)(struct device *dev, int power_on, int vdd);
+ /* Call back after enabling / disabling regulators */
+ void (*after_set_reg)(struct device *dev, int power_on, int vdd);
+ /* if we have special card, init it using this callback */
+ void (*init_card)(struct mmc_card *card);
+
+ const char *name;
+ u32 ocr_mask;
+};
-#ifndef __MACH_ATMEL_MCI_H
-#define __MACH_ATMEL_MCI_H
+#ifndef __MMC_ATMEL_MCI_H
+#define __MMC_ATMEL_MCI_H
#include <linux/platform_data/dma-atmel.h>
+#include <linux/platform_data/dma-dw.h>
/**
* struct mci_dma_data - DMA data for MCI interface
*/
struct mci_dma_data {
- struct at_dma_slave sdata;
+#ifdef CONFIG_ARM
+ struct at_dma_slave sdata;
+#else
+ struct dw_dma_slave sdata;
+#endif
};
/* accessor macros */
#define slave_data_ptr(s) (&(s)->sdata)
#define find_slave_dev(s) ((s)->sdata.dma_dev)
-#endif /* __MACH_ATMEL_MCI_H */
+#endif /* __MMC_ATMEL_MCI_H */
#define OMAP_MMC_MAX_SLOTS 2
-/*
- * struct omap_mmc_dev_attr.flags possibilities
- *
- * OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
- * operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
- * should be set if this is the case. See for example Section 22.5.3
- * "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
- * Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
- *
- * OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
- * don't work correctly on some MMC controller instances on some
- * OMAP3 SoCs; this flag should be set if this is the case. See
- * for example Advisory 2.1.1.128 "MMC: Multiple Block Read
- * Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
- * Revision F (October 2010) (SPRZ278F).
- */
-#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0)
-#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1)
-#define OMAP_HSMMC_SWAKEUP_MISSING BIT(2)
-
struct mmc_card;
-struct omap_mmc_dev_attr {
- u8 flags;
-};
-
struct omap_mmc_platform_data {
/* back-link to device */
struct device *dev;
unsigned vcc_aux_disable_is_sleep:1;
/* we can put the features above into this variable */
-#define HSMMC_HAS_PBIAS (1 << 0)
-#define HSMMC_HAS_UPDATED_RESET (1 << 1)
-#define HSMMC_HAS_HSPE_SUPPORT (1 << 2)
#define MMC_OMAP7XX (1 << 3)
#define MMC_OMAP15XX (1 << 4)
#define MMC_OMAP16XX (1 << 5)
unsigned int quirks2;
unsigned int pm_caps;
};
-
-struct sdhci_pxa {
- u8 clk_enable;
- u8 power_mode;
-};
#endif /* _PXA_SDHCI_H_ */
header-y += virtio_pci.h
header-y += virtio_ring.h
header-y += virtio_rng.h
-header=y += vm_sockets.h
+header-y += vm_sockets.h
header-y += vt.h
header-y += wait.h
header-y += wanrouter.h
return retval;
}
- id = ipc_addid(&sem_ids(ns), &sma->sem_perm, ns->sc_semmni);
- if (id < 0) {
- ipc_rcu_putref(sma, sem_rcu_free);
- return id;
- }
- ns->used_sems += nsems;
-
sma->sem_base = (struct sem *) &sma[1];
for (i = 0; i < nsems; i++) {
INIT_LIST_HEAD(&sma->list_id);
sma->sem_nsems = nsems;
sma->sem_ctime = get_seconds();
+
+ id = ipc_addid(&sem_ids(ns), &sma->sem_perm, ns->sc_semmni);
+ if (id < 0) {
+ ipc_rcu_putref(sma, sem_rcu_free);
+ return id;
+ }
+ ns->used_sems += nsems;
+
sem_unlock(sma, -1);
rcu_read_unlock();
* or we have been woken up remotely but the IPI has not yet arrived,
* we haven't yet exited the RCU idle mode. Do it here manually until
* we find a better solution.
+ *
+ * NB: There are buggy callers of this function. Ideally we
+ * should warn if prev_state != IN_USER, but that will trigger
+ * too frequently to make sense yet.
*/
- user_exit();
+ enum ctx_state prev_state = exception_enter();
schedule();
- user_enter();
+ exception_exit(prev_state);
}
#endif
return pool;
}
+EXPORT_SYMBOL(devm_gen_pool_create);
/**
* dev_get_gen_pool - Obtain the gen_pool (if any) for a device
continue;
total += zone->present_pages;
- reserved = zone->present_pages - zone->managed_pages;
+ reserved += zone->present_pages - zone->managed_pages;
if (is_highmem_idx(zoneid))
highmem += zone->present_pages;
the (older) page from frontswap
*/
inc_frontswap_failed_stores();
- if (dup)
+ if (dup) {
__frontswap_clear(sis, offset);
+ frontswap_ops->invalidate_page(type, offset);
+ }
}
if (frontswap_writethrough_enabled)
/* report failure so swap also writes to swap device */
if (!pte_file(pte)) {
swp_entry_t entry = pte_to_swp_entry(pte);
- if (swap_duplicate(entry) < 0)
- return entry.val;
-
- /* make sure dst_mm is on swapoff's mmlist. */
- if (unlikely(list_empty(&dst_mm->mmlist))) {
- spin_lock(&mmlist_lock);
- if (list_empty(&dst_mm->mmlist))
- list_add(&dst_mm->mmlist,
- &src_mm->mmlist);
- spin_unlock(&mmlist_lock);
- }
- if (likely(!non_swap_entry(entry)))
+ if (likely(!non_swap_entry(entry))) {
+ if (swap_duplicate(entry) < 0)
+ return entry.val;
+
+ /* make sure dst_mm is on swapoff's mmlist. */
+ if (unlikely(list_empty(&dst_mm->mmlist))) {
+ spin_lock(&mmlist_lock);
+ if (list_empty(&dst_mm->mmlist))
+ list_add(&dst_mm->mmlist,
+ &src_mm->mmlist);
+ spin_unlock(&mmlist_lock);
+ }
rss[MM_SWAPENTS]++;
- else if (is_migration_entry(entry)) {
+ } else if (is_migration_entry(entry)) {
page = migration_entry_to_page(entry);
if (PageAnon(page))
* shrinking vma had, to cover any anon pages imported.
*/
if (exporter && exporter->anon_vma && !importer->anon_vma) {
- if (anon_vma_clone(importer, exporter))
- return -ENOMEM;
+ int error;
+
+ error = anon_vma_clone(importer, exporter);
+ if (error)
+ return error;
importer->anon_vma = exporter->anon_vma;
}
}
if (err)
goto out_free_vma;
- if (anon_vma_clone(new, vma))
+ err = anon_vma_clone(new, vma);
+ if (err)
goto out_free_mpol;
if (new->vm_file)
{
struct anon_vma_chain *avc;
struct anon_vma *anon_vma;
+ int error;
/* Don't bother if the parent process has no anon_vma here. */
if (!pvma->anon_vma)
* First, attach the new VMA to the parent VMA's anon_vmas,
* so rmap can find non-COWed pages in child processes.
*/
- if (anon_vma_clone(vma, pvma))
- return -ENOMEM;
+ error = anon_vma_clone(vma, pvma);
+ if (error)
+ return error;
/* Then add our own anon_vma. */
anon_vma = anon_vma_alloc();
void *obj;
int x;
- VM_BUG_ON(nodeid > num_online_nodes());
+ VM_BUG_ON(nodeid < 0 || nodeid >= MAX_NUMNODES);
n = get_node(cachep, nodeid);
BUG_ON(!n);
unsigned long scanned;
unsigned long reclaimed;
+ spin_lock(&vmpr->sr_lock);
/*
* Several contexts might be calling vmpressure(), so it is
* possible that the work was rescheduled again before the old
* here. No need for any locks here since we don't care if
* vmpr->reclaimed is in sync.
*/
- if (!vmpr->scanned)
+ scanned = vmpr->scanned;
+ if (!scanned) {
+ spin_unlock(&vmpr->sr_lock);
return;
+ }
- spin_lock(&vmpr->sr_lock);
- scanned = vmpr->scanned;
reclaimed = vmpr->reclaimed;
vmpr->scanned = 0;
vmpr->reclaimed = 0;
goto errout;
}
if (!netlink_ns_capable(skb, net->user_ns, CAP_NET_ADMIN)) {
+ put_net(net);
err = -EPERM;
goto errout;
}
#define KEYRING_SEARCH_NO_UPDATE_TIME 0x0004 /* Don't update times */
#define KEYRING_SEARCH_NO_CHECK_PERM 0x0008 /* Don't check permissions */
#define KEYRING_SEARCH_DETECT_TOO_DEEP 0x0010 /* Give an error on excessive depth */
+#define KEYRING_SEARCH_SKIP_EXPIRED 0x0020 /* Ignore expired keys (intention to replace) */
int (*iterator)(const void *object, void *iterator_data);
#include <asm/uaccess.h>
#include "internal.h"
+#define KEY_MAX_DESC_SIZE 4096
+
static int key_get_type_from_user(char *type,
const char __user *_type,
unsigned len)
description = NULL;
if (_description) {
- description = strndup_user(_description, PAGE_SIZE);
+ description = strndup_user(_description, KEY_MAX_DESC_SIZE);
if (IS_ERR(description)) {
ret = PTR_ERR(description);
goto error;
goto error;
/* pull the description into kernel space */
- description = strndup_user(_description, PAGE_SIZE);
+ description = strndup_user(_description, KEY_MAX_DESC_SIZE);
if (IS_ERR(description)) {
ret = PTR_ERR(description);
goto error;
/* fetch the name from userspace */
name = NULL;
if (_name) {
- name = strndup_user(_name, PAGE_SIZE);
+ name = strndup_user(_name, KEY_MAX_DESC_SIZE);
if (IS_ERR(name)) {
ret = PTR_ERR(name);
goto error;
{
struct key *key, *instkey;
key_ref_t key_ref;
- char *tmpbuf;
+ char *infobuf;
long ret;
+ int desclen, infolen;
key_ref = lookup_user_key(keyid, KEY_LOOKUP_PARTIAL, KEY_NEED_VIEW);
if (IS_ERR(key_ref)) {
}
okay:
- /* calculate how much description we're going to return */
- ret = -ENOMEM;
- tmpbuf = kmalloc(PAGE_SIZE, GFP_KERNEL);
- if (!tmpbuf)
- goto error2;
-
key = key_ref_to_ptr(key_ref);
+ desclen = strlen(key->description);
- ret = snprintf(tmpbuf, PAGE_SIZE - 1,
- "%s;%d;%d;%08x;%s",
- key->type->name,
- from_kuid_munged(current_user_ns(), key->uid),
- from_kgid_munged(current_user_ns(), key->gid),
- key->perm,
- key->description ?: "");
-
- /* include a NUL char at the end of the data */
- if (ret > PAGE_SIZE - 1)
- ret = PAGE_SIZE - 1;
- tmpbuf[ret] = 0;
- ret++;
+ /* calculate how much information we're going to return */
+ ret = -ENOMEM;
+ infobuf = kasprintf(GFP_KERNEL,
+ "%s;%d;%d;%08x;",
+ key->type->name,
+ from_kuid_munged(current_user_ns(), key->uid),
+ from_kgid_munged(current_user_ns(), key->gid),
+ key->perm);
+ if (!infobuf)
+ goto error2;
+ infolen = strlen(infobuf);
+ ret = infolen + desclen + 1;
/* consider returning the data */
- if (buffer && buflen > 0) {
- if (buflen > ret)
- buflen = ret;
-
- if (copy_to_user(buffer, tmpbuf, buflen) != 0)
+ if (buffer && buflen >= ret) {
+ if (copy_to_user(buffer, infobuf, infolen) != 0 ||
+ copy_to_user(buffer + infolen, key->description,
+ desclen + 1) != 0)
ret = -EFAULT;
}
- kfree(tmpbuf);
+ kfree(infobuf);
error2:
key_ref_put(key_ref);
error:
if (ret < 0)
goto error;
- description = strndup_user(_description, PAGE_SIZE);
+ description = strndup_user(_description, KEY_MAX_DESC_SIZE);
if (IS_ERR(description)) {
ret = PTR_ERR(description);
goto error;
}
if (key->expiry && ctx->now.tv_sec >= key->expiry) {
- ctx->result = ERR_PTR(-EKEYEXPIRED);
+ if (!(ctx->flags & KEYRING_SEARCH_SKIP_EXPIRED))
+ ctx->result = ERR_PTR(-EKEYEXPIRED);
kleave(" = %d [expire]", ctx->skipped_ret);
goto skipped;
}
ctx->index_key.type->name,
ctx->index_key.description);
+#define STATE_CHECKS (KEYRING_SEARCH_NO_STATE_CHECK | KEYRING_SEARCH_DO_STATE_CHECK)
+ BUG_ON((ctx->flags & STATE_CHECKS) == 0 ||
+ (ctx->flags & STATE_CHECKS) == STATE_CHECKS);
+
if (ctx->index_key.description)
ctx->index_key.desc_len = strlen(ctx->index_key.description);
if (ctx->match_data.lookup_type == KEYRING_SEARCH_LOOKUP_ITERATE ||
keyring_compare_object(keyring, &ctx->index_key)) {
ctx->skipped_ret = 2;
- ctx->flags |= KEYRING_SEARCH_DO_STATE_CHECK;
switch (ctx->iterator(keyring_key_to_ptr(keyring), ctx)) {
case 1:
goto found;
}
ctx->skipped_ret = 0;
- if (ctx->flags & KEYRING_SEARCH_NO_STATE_CHECK)
- ctx->flags &= ~KEYRING_SEARCH_DO_STATE_CHECK;
/* Start processing a new keyring */
descend_to_keyring:
.match_data.cmp = key_default_cmp,
.match_data.raw_data = description,
.match_data.lookup_type = KEYRING_SEARCH_LOOKUP_DIRECT,
+ .flags = (KEYRING_SEARCH_DO_STATE_CHECK |
+ KEYRING_SEARCH_SKIP_EXPIRED),
};
struct key *key;
key_ref_t key_ref;
.match_data.cmp = key_default_cmp,
.match_data.raw_data = description,
.match_data.lookup_type = KEYRING_SEARCH_LOOKUP_DIRECT,
+ .flags = KEYRING_SEARCH_DO_STATE_CHECK,
};
struct key *authkey;
key_ref_t authkey_ref;
SND_PCI_QUIRK(0x1028, 0x0638, "Dell Inspiron 5439", ALC290_FIXUP_MONO_SPEAKERS_HSJACK),
SND_PCI_QUIRK(0x1028, 0x064a, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x064b, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x06d9, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
+ SND_PCI_QUIRK(0x1028, 0x06da, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x164a, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x1028, 0x164b, "Dell", ALC293_FIXUP_DELL1_MIC_NO_PRESENCE),
SND_PCI_QUIRK(0x103c, 0x1586, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC2),
projects / linux-beck.git / commitdiff