#define SCPCELLID2 0xFF8
#define SCPCELLID3 0xFFC
+#define SCCTRL_TIMEREN0SEL_REFCLK (0 << 15)
+#define SCCTRL_TIMEREN0SEL_TIMCLK (1 << 15)
+
+#define SCCTRL_TIMEREN1SEL_REFCLK (0 << 17)
+#define SCCTRL_TIMEREN1SEL_TIMCLK (1 << 17)
+
static inline void sysctl_soft_reset(void __iomem *base)
{
/* writing any value to SCSYSSTAT reg will reset system */
* translation for translating DMA addresses. Use the driver
* DMA support - see dma-mapping.h.
*/
-static inline unsigned long virt_to_phys(void *x)
+static inline unsigned long virt_to_phys(const volatile void *x)
{
return __virt_to_phys((unsigned long)(x));
}
/* timer load already set up */
ctrl = TWD_TIMER_CONTROL_ENABLE | TWD_TIMER_CONTROL_IT_ENABLE
| TWD_TIMER_CONTROL_PERIODIC;
+ __raw_writel(twd_timer_rate / HZ, twd_base + TWD_TIMER_LOAD);
break;
case CLOCK_EVT_MODE_ONESHOT:
/* period set, and timer enabled in 'next_event' hook */
static void __cpuinit twd_calibrate_rate(void)
{
- unsigned long load, count;
+ unsigned long count;
u64 waitjiffies;
/*
printk("%lu.%02luMHz.\n", twd_timer_rate / 1000000,
(twd_timer_rate / 1000000) % 100);
}
-
- load = twd_timer_rate / HZ;
-
- __raw_writel(load, twd_base + TWD_TIMER_LOAD);
}
/*
{
int i;
+ /* Set Ports C, D, E, G, and H for GPIO use */
+ ep93xx_devcfg_set_bits(EP93XX_SYSCON_DEVCFG_KEYS |
+ EP93XX_SYSCON_DEVCFG_GONK |
+ EP93XX_SYSCON_DEVCFG_EONIDE |
+ EP93XX_SYSCON_DEVCFG_GONIDE |
+ EP93XX_SYSCON_DEVCFG_HONIDE);
+
for (i = 0; i < ARRAY_SIZE(ep93xx_gpio_banks); i++)
gpiochip_add(&ep93xx_gpio_banks[i].chip);
}
depends on ARCH_REALVIEW
config MACH_REALVIEW_EB
- bool "Support RealView/EB platform"
+ bool "Support RealView(R) Emulation Baseboard"
select ARM_GIC
help
- Include support for the ARM(R) RealView Emulation Baseboard platform.
+ Include support for the ARM(R) RealView(R) Emulation Baseboard
+ platform.
config REALVIEW_EB_A9MP
- bool "Support Multicore Cortex-A9"
+ bool "Support Multicore Cortex-A9 Tile"
depends on MACH_REALVIEW_EB
select CPU_V7
help
- Enable support for the Cortex-A9MPCore tile on the Realview platform.
+ Enable support for the Cortex-A9MPCore tile fitted to the
+ Realview(R) Emulation Baseboard platform.
config REALVIEW_EB_ARM11MP
- bool "Support ARM11MPCore tile"
+ bool "Support ARM11MPCore Tile"
depends on MACH_REALVIEW_EB
select CPU_V6
select ARCH_HAS_BARRIERS if SMP
help
- Enable support for the ARM11MPCore tile on the Realview platform.
+ Enable support for the ARM11MPCore tile fitted to the Realview(R)
+ Emulation Baseboard platform.
config REALVIEW_EB_ARM11MP_REVB
- bool "Support ARM11MPCore RevB tile"
+ bool "Support ARM11MPCore RevB Tile"
depends on REALVIEW_EB_ARM11MP
help
- Enable support for the ARM11MPCore RevB tile on the Realview
- platform. Since there are device address differences, a
- kernel built with this option enabled is not compatible with
- other revisions of the ARM11MPCore tile.
+ Enable support for the ARM11MPCore Revision B tile on the
+ Realview(R) Emulation Baseboard platform. Since there are device
+ address differences, a kernel built with this option enabled is
+ not compatible with other revisions of the ARM11MPCore tile.
config MACH_REALVIEW_PB11MP
- bool "Support RealView/PB11MPCore platform"
+ bool "Support RealView(R) Platform Baseboard for ARM11MPCore"
select CPU_V6
select ARM_GIC
select HAVE_PATA_PLATFORM
select ARCH_HAS_BARRIERS if SMP
help
- Include support for the ARM(R) RealView MPCore Platform Baseboard.
- PB11MPCore is a platform with an on-board ARM11MPCore and has
+ Include support for the ARM(R) RealView(R) Platform Baseboard for
+ the ARM11MPCore. This platform has an on-board ARM11MPCore and has
support for PCI-E and Compact Flash.
config MACH_REALVIEW_PB1176
- bool "Support RealView/PB1176 platform"
+ bool "Support RealView(R) Platform Baseboard for ARM1176JZF-S"
select CPU_V6
select ARM_GIC
help
- Include support for the ARM(R) RealView ARM1176 Platform Baseboard.
+ Include support for the ARM(R) RealView(R) Platform Baseboard for
+ ARM1176JZF-S.
config REALVIEW_PB1176_SECURE_FLASH
bool "Allow access to the secure flash memory block"
block (64MB @ 0x3c000000) is required.
config MACH_REALVIEW_PBA8
- bool "Support RealView/PB-A8 platform"
+ bool "Support RealView(R) Platform Baseboard for Cortex(tm)-A8 platform"
select CPU_V7
select ARM_GIC
select HAVE_PATA_PLATFORM
help
- Include support for the ARM(R) RealView Cortex-A8 Platform Baseboard.
- PB-A8 is a platform with an on-board Cortex-A8 and has support for
- PCI-E and Compact Flash.
+ Include support for the ARM(R) RealView Platform Baseboard for
+ Cortex(tm)-A8. This platform has an on-board Cortex-A8 and has
+ support for PCI-E and Compact Flash.
config MACH_REALVIEW_PBX
- bool "Support RealView/PBX platform"
+ bool "Support RealView(R) Platform Baseboard Explore"
select ARM_GIC
select HAVE_PATA_PLATFORM
select ARCH_SPARSEMEM_ENABLE if CPU_V7 && !REALVIEW_HIGH_PHYS_OFFSET
select ZONE_DMA if SPARSEMEM
help
- Include support for the ARM(R) RealView PBX platform.
+ Include support for the ARM(R) RealView(R) Platform Baseboard
+ Explore.
config REALVIEW_HIGH_PHYS_OFFSET
bool "High physical base address for the RealView platform"
* observers, irrespective of whether they're taking part in coherency
* or not. This is necessary for the hotplug code to work reliably.
*/
-static void write_pen_release(int val)
+static void __cpuinit write_pen_release(int val)
{
pen_release = val;
smp_wmb();
depends on ARCH_VERSATILE
config ARCH_VERSATILE_PB
- bool "Support Versatile/PB platform"
+ bool "Support Versatile Platform Baseboard for ARM926EJ-S"
select CPU_ARM926T
select MIGHT_HAVE_PCI
default y
help
- Include support for the ARM(R) Versatile/PB platform.
+ Include support for the ARM(R) Versatile Platform Baseboard
+ for the ARM926EJ-S.
config MACH_VERSATILE_AB
- bool "Support Versatile/AB platform"
+ bool "Support Versatile Application Baseboard for ARM926EJ-S"
select CPU_ARM926T
help
- Include support for the ARM(R) Versatile/AP platform.
+ Include support for the ARM(R) Versatile Application Baseboard
+ for the ARM926EJ-S.
endmenu
* observers, irrespective of whether they're taking part in coherency
* or not. This is necessary for the hotplug code to work reliably.
*/
-static void write_pen_release(int val)
+static void __cpuinit write_pen_release(int val)
{
pen_release = val;
smp_wmb();
#include <asm/mach/time.h>
#include <asm/hardware/arm_timer.h>
#include <asm/hardware/timer-sp.h>
+#include <asm/hardware/sp810.h>
#include <mach/motherboard.h>
static void __init v2m_timer_init(void)
{
+ u32 scctrl;
+
versatile_sched_clock_init(MMIO_P2V(V2M_SYS_24MHZ), 24000000);
+ /* Select 1MHz TIMCLK as the reference clock for SP804 timers */
+ scctrl = readl(MMIO_P2V(V2M_SYSCTL + SCCTRL));
+ scctrl |= SCCTRL_TIMEREN0SEL_TIMCLK;
+ scctrl |= SCCTRL_TIMEREN1SEL_TIMCLK;
+ writel(scctrl, MMIO_P2V(V2M_SYSCTL + SCCTRL));
+
writel(0, MMIO_P2V(V2M_TIMER0) + TIMER_CTRL);
writel(0, MMIO_P2V(V2M_TIMER1) + TIMER_CTRL);
#define DRIVER_NAME "aaci-pl041"
+#define FRAME_PERIOD_US 21
+
/*
* PM support is not complete. Turn it off.
*/
unsigned short val)
{
struct aaci *aaci = ac97->private_data;
+ int timeout;
u32 v;
- int timeout = 5000;
if (ac97->num >= 4)
return;
writel(val << 4, aaci->base + AACI_SL2TX);
writel(reg << 12, aaci->base + AACI_SL1TX);
- /*
- * Wait for the transmission of both slots to complete.
- */
+ /* Initially, wait one frame period */
+ udelay(FRAME_PERIOD_US);
+
+ /* And then wait an additional eight frame periods for it to be sent */
+ timeout = FRAME_PERIOD_US * 8;
do {
+ udelay(1);
v = readl(aaci->base + AACI_SLFR);
} while ((v & (SLFR_1TXB|SLFR_2TXB)) && --timeout);
- if (!timeout)
+ if (v & (SLFR_1TXB|SLFR_2TXB))
dev_err(&aaci->dev->dev,
"timeout waiting for write to complete\n");
static unsigned short aaci_ac97_read(struct snd_ac97 *ac97, unsigned short reg)
{
struct aaci *aaci = ac97->private_data;
+ int timeout, retries = 10;
u32 v;
- int timeout = 5000;
- int retries = 10;
if (ac97->num >= 4)
return ~0;
*/
writel((reg << 12) | (1 << 19), aaci->base + AACI_SL1TX);
- /*
- * Wait for the transmission to complete.
- */
+ /* Initially, wait one frame period */
+ udelay(FRAME_PERIOD_US);
+
+ /* And then wait an additional eight frame periods for it to be sent */
+ timeout = FRAME_PERIOD_US * 8;
do {
+ udelay(1);
v = readl(aaci->base + AACI_SLFR);
} while ((v & SLFR_1TXB) && --timeout);
- if (!timeout) {
+ if (v & SLFR_1TXB) {
dev_err(&aaci->dev->dev, "timeout on slot 1 TX busy\n");
v = ~0;
goto out;
}
- /*
- * Give the AC'97 codec more than enough time
- * to respond. (42us = ~2 frames at 48kHz.)
- */
- udelay(42);
+ /* Now wait for the response frame */
+ udelay(FRAME_PERIOD_US);
- /*
- * Wait for slot 2 to indicate data.
- */
- timeout = 5000;
+ /* And then wait an additional eight frame periods for data */
+ timeout = FRAME_PERIOD_US * 8;
do {
+ udelay(1);
cond_resched();
v = readl(aaci->base + AACI_SLFR) & (SLFR_1RXV|SLFR_2RXV);
} while ((v != (SLFR_1RXV|SLFR_2RXV)) && --timeout);
- if (!timeout) {
+ if (v != (SLFR_1RXV|SLFR_2RXV)) {
dev_err(&aaci->dev->dev, "timeout on RX valid\n");
v = ~0;
goto out;
int timeout = 5000;
do {
+ udelay(1);
val = readl(aacirun->base + AACI_SR);
} while (val & mask && timeout--);
}
* Give the AC'97 codec more than enough time
* to wake up. (42us = ~2 frames at 48kHz.)
*/
- udelay(42);
+ udelay(FRAME_PERIOD_US * 2);
ret = snd_ac97_bus(aaci->card, 0, &aaci_bus_ops, aaci, &ac97_bus);
if (ret)
projects / mv-sheeva.git / commitdiff