serial: sirf: define macro for some magic numbers of USP

this patch clears some magic numbers for offset and bitshift
of USP registers.

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/tty/serial/sirfsoc_uart.c b/drivers/tty/serial/sirfsoc_uart.c
index 96304cdc474548f82d66b3801bf4097aade6927c..aaa3ce22b5b892b9a85aca3fda84f3a0f02a93ac 100644 (file)
--- a/drivers/tty/serial/sirfsoc_uart.c
+++ b/drivers/tty/serial/sirfsoc_uart.c
@@ -951,11 +951,11 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
                set_baud = ((ioclk_rate / (clk_div_reg+1) - 1) /
                                (sample_div_reg + 1));
                /* setting usp mode 2 */
-               len_val = ((1 << 0) | (1 << 8));
-               len_val |= ((clk_div_reg & 0x3ff) << 21);
-               wr_regl(port, ureg->sirfsoc_mode2,
-                               len_val);
-
+               len_val = ((1 << SIRFSOC_USP_MODE2_RXD_DELAY_OFFSET) |
+                               (1 << SIRFSOC_USP_MODE2_TXD_DELAY_OFFSET));
+               len_val |= ((clk_div_reg & SIRFSOC_USP_MODE2_CLK_DIVISOR_MASK)
+                               << SIRFSOC_USP_MODE2_CLK_DIVISOR_OFFSET);
+               wr_regl(port, ureg->sirfsoc_mode2, len_val);
        }
        if (tty_termios_baud_rate(termios))
                tty_termios_encode_baud_rate(termios, set_baud, set_baud);
@@ -963,7 +963,7 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
        rx_time_out = SIRFSOC_UART_RX_TIMEOUT(set_baud, 20000);
        rx_time_out = SIRFUART_RECV_TIMEOUT_VALUE(rx_time_out);
        txfifo_op_reg = rd_regl(port, ureg->sirfsoc_tx_fifo_op);
-       wr_regl(port, ureg->sirfsoc_rx_fifo_op, 0);
+       wr_regl(port, ureg->sirfsoc_rx_fifo_op, SIRFUART_FIFO_STOP);
        wr_regl(port, ureg->sirfsoc_tx_fifo_op,
                        (txfifo_op_reg & ~SIRFUART_FIFO_START));
        if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
@@ -971,21 +971,28 @@ static void sirfsoc_uart_set_termios(struct uart_port *port,
                wr_regl(port, ureg->sirfsoc_line_ctrl, config_reg);
        } else {
                /*tx frame ctrl*/
-               len_val = (data_bit_len - 1) << 0;
-               len_val |= (data_bit_len + 1 + stop_bit_len - 1) << 16;
-               len_val |= ((data_bit_len - 1) << 24);
-               len_val |= (((clk_div_reg & 0xc00) >> 10) << 30);
+               len_val = (data_bit_len - 1) << SIRFSOC_USP_TX_DATA_LEN_OFFSET;
+               len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
+                               SIRFSOC_USP_TX_FRAME_LEN_OFFSET;
+               len_val |= ((data_bit_len - 1) <<
+                               SIRFSOC_USP_TX_SHIFTER_LEN_OFFSET);
+               len_val |= (((clk_div_reg & 0xc00) >> 10) <<
+                               SIRFSOC_USP_TX_CLK_DIVISOR_OFFSET);
                wr_regl(port, ureg->sirfsoc_tx_frame_ctrl, len_val);
                /*rx frame ctrl*/
-               len_val = (data_bit_len - 1) << 0;
-               len_val |= (data_bit_len + 1 + stop_bit_len - 1) << 8;
-               len_val |= (data_bit_len - 1) << 16;
-               len_val |= (((clk_div_reg & 0xf000) >> 12) << 24);
+               len_val = (data_bit_len - 1) << SIRFSOC_USP_RX_DATA_LEN_OFFSET;
+               len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
+                               SIRFSOC_USP_RX_FRAME_LEN_OFFSET;
+               len_val |= (data_bit_len - 1) <<
+                               SIRFSOC_USP_RX_SHIFTER_LEN_OFFSET;
+               len_val |= (((clk_div_reg & 0xf000) >> 12) <<
+                               SIRFSOC_USP_RX_CLK_DIVISOR_OFFSET);
                wr_regl(port, ureg->sirfsoc_rx_frame_ctrl, len_val);
                /*async param*/
                wr_regl(port, ureg->sirfsoc_async_param_reg,
                        (SIRFUART_RECV_TIMEOUT(port, rx_time_out)) |
-                       (sample_div_reg & 0x3f) << 16);
+                       (sample_div_reg & SIRFSOC_USP_ASYNC_DIV2_MASK) <<
+                       SIRFSOC_USP_ASYNC_DIV2_OFFSET);
        }
        if (IS_DMA_CHAN_VALID(sirfport->tx_dma_no))
                wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_DMA_MODE);

diff --git a/drivers/tty/serial/sirfsoc_uart.h b/drivers/tty/serial/sirfsoc_uart.h
index 173e00f84c67e94ce27ca8a170ff350c551f2521..c43333dfab4ab1b96eee078fead34738a71f8ee2 100644 (file)
--- a/drivers/tty/serial/sirfsoc_uart.h
+++ b/drivers/tty/serial/sirfsoc_uart.h
@@ -311,6 +311,21 @@ struct sirfsoc_uart_register sirfsoc_uart = {
 /* USP SPEC */
 #define SIRFSOC_USP_ENDIAN_CTRL_LSBF           BIT(4)
 #define SIRFSOC_USP_EN                         BIT(5)
+#define SIRFSOC_USP_MODE2_RXD_DELAY_OFFSET     0
+#define SIRFSOC_USP_MODE2_TXD_DELAY_OFFSET     8
+#define SIRFSOC_USP_MODE2_CLK_DIVISOR_MASK     0x3ff
+#define SIRFSOC_USP_MODE2_CLK_DIVISOR_OFFSET   21
+#define SIRFSOC_USP_TX_DATA_LEN_OFFSET         0
+#define SIRFSOC_USP_TX_SYNC_LEN_OFFSET         8
+#define SIRFSOC_USP_TX_FRAME_LEN_OFFSET                16
+#define SIRFSOC_USP_TX_SHIFTER_LEN_OFFSET      24
+#define SIRFSOC_USP_TX_CLK_DIVISOR_OFFSET      30
+#define SIRFSOC_USP_RX_DATA_LEN_OFFSET         0
+#define SIRFSOC_USP_RX_FRAME_LEN_OFFSET                8
+#define SIRFSOC_USP_RX_SHIFTER_LEN_OFFSET      16
+#define SIRFSOC_USP_RX_CLK_DIVISOR_OFFSET      24
+#define SIRFSOC_USP_ASYNC_DIV2_MASK            0x3f
+#define SIRFSOC_USP_ASYNC_DIV2_OFFSET          16
 
 /* USP-UART Common */
 #define SIRFSOC_UART_RX_TIMEOUT(br, to)        (((br) * (((to) + 999) / 1000)) / 1000)