Sarah writes:
xhci: Step 2 to fix usb-linus and usb-next.
Hi Greg,
This is the first of two steps to fix your usb-linus and usb-next trees.
As I mentioned, commit
4fae6f0fa86f92e6bc7429371b1e177ad0aaac66 "USB:
handle LPM errors during device suspend correctly" was incorrectly added
to usb-next when it should have been added to usb-linus and marked for
stable.
Two port power off bug fixes touch the same code that patch touches, but
it's not easy to simply move commit
4fae6f0f patch to usb-linus because
commit
28e861658e23ca94692f98e245d254c75c8088a7 "USB: refactor code for
enabling/disabling remote wakeup" also touched those code sections.
I propose a two step process to fix this:
1. Pull these four patches into usb-linus.
2. Revert commit
28e861658e23ca94692f98e245d254c75c8088a7 from usb-next.
Merge usb-linus into usb-next, and resolve the conflicts.
I will be sending pull requests for these steps.
This pull request is step two.
Sarah Sharp
usb_set_device_state(udev, USB_STATE_SUSPENDED);
}
- /*
- * Check whether current status meets the requirement of
- * usb port power off mechanism
- */
if (status == 0 && !udev->do_remote_wakeup && udev->persist_enabled) {
- enum pm_qos_flags_status pm_qos_stat;
-
- pm_qos_stat = dev_pm_qos_flags(&port_dev->dev,
- PM_QOS_FLAG_NO_POWER_OFF);
- if (pm_qos_stat != PM_QOS_FLAGS_ALL) {
- pm_runtime_put_sync(&port_dev->dev);
- port_dev->did_runtime_put = true;
- }
+ pm_runtime_put_sync(&port_dev->dev);
+ port_dev->did_runtime_put = true;
}
usb_mark_last_busy(hub->hdev);
retval = usb_hub_set_port_power(hdev, hub, port1, true);
if (port_dev->child && !retval) {
/*
- * Wait for usb hub port to be reconnected in order to make
- * the resume procedure successful.
+ * Attempt to wait for usb hub port to be reconnected in order
+ * to make the resume procedure successful. The device may have
+ * disconnected while the port was powered off, so ignore the
+ * return status.
*/
retval = hub_port_debounce_be_connected(hub, port1);
- if (retval < 0) {
+ if (retval < 0)
dev_dbg(&port_dev->dev, "can't get reconnection after setting port power on, status %d\n",
retval);
- goto out;
- }
usb_clear_port_feature(hdev, port1, USB_PORT_FEAT_C_ENABLE);
-
- /* Set return value to 0 if debounce successful */
retval = 0;
}
-out:
clear_bit(port1, hub->busy_bits);
usb_autopm_put_interface(intf);
return retval;
* here that the generic code does not try to make a pci_dev from our
* dev struct in order to setup MSI
*/
- xhci->quirks |= XHCI_BROKEN_MSI;
+ xhci->quirks |= XHCI_PLAT;
}
/* called during probe() after chip reset completes */
static int xhci_try_enable_msi(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
- struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
+ struct pci_dev *pdev;
int ret;
+ /* The xhci platform device has set up IRQs through usb_add_hcd. */
+ if (xhci->quirks & XHCI_PLAT)
+ return 0;
+
+ pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller);
/*
* Some Fresco Logic host controllers advertise MSI, but fail to
* generate interrupts. Don't even try to enable MSI.
#define XHCI_SPURIOUS_REBOOT (1 << 13)
#define XHCI_COMP_MODE_QUIRK (1 << 14)
#define XHCI_AVOID_BEI (1 << 15)
+#define XHCI_PLAT (1 << 16)
unsigned int num_active_eps;
unsigned int limit_active_eps;
/* There are two roothubs to keep track of bus suspend info for */