#ifndef __iwl_3945_commands_h__
#define __iwl_3945_commands_h__
-/* uCode version contains 4 values: Major/Minor/API/Serial */
-#define IWL_UCODE_MAJOR(ver) (((ver) & 0xFF000000) >> 24)
-#define IWL_UCODE_MINOR(ver) (((ver) & 0x00FF0000) >> 16)
-#define IWL_UCODE_API(ver) (((ver) & 0x0000FF00) >> 8)
-#define IWL_UCODE_SERIAL(ver) ((ver) & 0x000000FF)
-
-
-/* Tx rates */
-#define IWL_CCK_RATES 4
-#define IWL_OFDM_RATES 8
-#define IWL_MAX_RATES (IWL_CCK_RATES + IWL_OFDM_RATES)
-
/******************************************************************************
* (0)
* Commonly used structures and definitions:
* Command header, txpower
*
*****************************************************************************/
-
-/* iwl3945_cmd_header flags value */
-#define IWL_CMD_FAILED_MSK 0x40
-
-/**
- * struct iwl3945_cmd_header
- *
- * This header format appears in the beginning of each command sent from the
- * driver, and each response/notification received from uCode.
- */
-struct iwl3945_cmd_header {
- u8 cmd; /* Command ID: REPLY_RXON, etc. */
- u8 flags; /* IWL_CMD_* */
- /*
- * The driver sets up the sequence number to values of its choosing.
- * uCode does not use this value, but passes it back to the driver
- * when sending the response to each driver-originated command, so
- * the driver can match the response to the command. Since the values
- * don't get used by uCode, the driver may set up an arbitrary format.
- *
- * There is one exception: uCode sets bit 15 when it originates
- * the response/notification, i.e. when the response/notification
- * is not a direct response to a command sent by the driver. For
- * example, uCode issues REPLY_3945_RX when it sends a received frame
- * to the driver; it is not a direct response to any driver command.
- *
- * The Linux driver uses the following format:
- *
- * 0:7 index/position within Tx queue
- * 8:13 Tx queue selection
- * 14:14 driver sets this to indicate command is in the 'huge'
- * storage at the end of the command buffers, i.e. scan cmd
- * 15:15 uCode sets this in uCode-originated response/notification
- */
- __le16 sequence;
-
- /* command or response/notification data follows immediately */
- u8 data[0];
-} __attribute__ ((packed));
-
/**
* struct iwl3945_tx_power
*
*
*****************************************************************************/
-#define UCODE_VALID_OK cpu_to_le32(0x1)
-#define INITIALIZE_SUBTYPE (9)
/*
* ("Initialize") REPLY_ALIVE = 0x1 (response only, not a command)
*
*****************************************************************************/
-/* rx_config flags */
-/* band & modulation selection */
-#define RXON_FLG_BAND_24G_MSK cpu_to_le32(1 << 0)
-#define RXON_FLG_CCK_MSK cpu_to_le32(1 << 1)
-/* auto detection enable */
-#define RXON_FLG_AUTO_DETECT_MSK cpu_to_le32(1 << 2)
-/* TGg protection when tx */
-#define RXON_FLG_TGG_PROTECT_MSK cpu_to_le32(1 << 3)
-/* cck short slot & preamble */
-#define RXON_FLG_SHORT_SLOT_MSK cpu_to_le32(1 << 4)
-#define RXON_FLG_SHORT_PREAMBLE_MSK cpu_to_le32(1 << 5)
-/* antenna selection */
-#define RXON_FLG_DIS_DIV_MSK cpu_to_le32(1 << 7)
-#define RXON_FLG_ANT_SEL_MSK cpu_to_le32(0x0f00)
-#define RXON_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
-#define RXON_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
-/* radar detection enable */
-#define RXON_FLG_RADAR_DETECT_MSK cpu_to_le32(1 << 12)
-#define RXON_FLG_TGJ_NARROW_BAND_MSK cpu_to_le32(1 << 13)
-/* rx response to host with 8-byte TSF
-* (according to ON_AIR deassertion) */
-#define RXON_FLG_TSF2HOST_MSK cpu_to_le32(1 << 15)
-
-/* rx_config filter flags */
-/* accept all data frames */
-#define RXON_FILTER_PROMISC_MSK cpu_to_le32(1 << 0)
-/* pass control & management to host */
-#define RXON_FILTER_CTL2HOST_MSK cpu_to_le32(1 << 1)
-/* accept multi-cast */
-#define RXON_FILTER_ACCEPT_GRP_MSK cpu_to_le32(1 << 2)
-/* don't decrypt uni-cast frames */
-#define RXON_FILTER_DIS_DECRYPT_MSK cpu_to_le32(1 << 3)
-/* don't decrypt multi-cast frames */
-#define RXON_FILTER_DIS_GRP_DECRYPT_MSK cpu_to_le32(1 << 4)
-/* STA is associated */
-#define RXON_FILTER_ASSOC_MSK cpu_to_le32(1 << 5)
-/* transfer to host non bssid beacons in associated state */
-#define RXON_FILTER_BCON_AWARE_MSK cpu_to_le32(1 << 6)
-
/**
* REPLY_RXON = 0x10 (command, has simple generic response)
*
struct iwl3945_power_per_rate power[IWL_MAX_RATES];
} __attribute__ ((packed));
-/*
- * CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
- */
-struct iwl3945_csa_notification {
- __le16 band;
- __le16 channel;
- __le32 status; /* 0 - OK, 1 - fail */
-} __attribute__ ((packed));
-
-/******************************************************************************
- * (2)
- * Quality-of-Service (QOS) Commands & Responses:
- *
- *****************************************************************************/
-
-/**
- * struct iwl_ac_qos -- QOS timing params for REPLY_QOS_PARAM
- * One for each of 4 EDCA access categories in struct iwl_qosparam_cmd
- *
- * @cw_min: Contention window, start value in numbers of slots.
- * Should be a power-of-2, minus 1. Device's default is 0x0f.
- * @cw_max: Contention window, max value in numbers of slots.
- * Should be a power-of-2, minus 1. Device's default is 0x3f.
- * @aifsn: Number of slots in Arbitration Interframe Space (before
- * performing random backoff timing prior to Tx). Device default 1.
- * @edca_txop: Length of Tx opportunity, in uSecs. Device default is 0.
- *
- * Device will automatically increase contention window by (2*CW) + 1 for each
- * transmission retry. Device uses cw_max as a bit mask, ANDed with new CW
- * value, to cap the CW value.
- */
-struct iwl3945_ac_qos {
- __le16 cw_min;
- __le16 cw_max;
- u8 aifsn;
- u8 reserved1;
- __le16 edca_txop;
-} __attribute__ ((packed));
-
-/* QoS flags defines */
-#define QOS_PARAM_FLG_UPDATE_EDCA_MSK cpu_to_le32(0x01)
-#define QOS_PARAM_FLG_TGN_MSK cpu_to_le32(0x02)
-#define QOS_PARAM_FLG_TXOP_TYPE_MSK cpu_to_le32(0x10)
-
-/* Number of Access Categories (AC) (EDCA), queues 0..3 */
-#define AC_NUM 4
-
-/*
- * REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
- *
- * This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
- * 0: Background, 1: Best Effort, 2: Video, 3: Voice.
- */
-struct iwl3945_qosparam_cmd {
- __le32 qos_flags;
- struct iwl3945_ac_qos ac[AC_NUM];
-} __attribute__ ((packed));
-
/******************************************************************************
* (3)
* Add/Modify Stations Commands & Responses:
*
*****************************************************************************/
-/*
- * Multi station support
- */
-
-/* Special, dedicated locations within device's station table */
-#define IWL_AP_ID 0
-#define IWL_MULTICAST_ID 1
-#define IWL_STA_ID 2
-#define IWL3945_BROADCAST_ID 24
-#define IWL3945_STATION_COUNT 25
-
-#define IWL_STATION_COUNT 32 /* MAX(3945,4965)*/
-#define IWL_INVALID_STATION 255
-
-#define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2);
-#define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8);
-
-/* Use in mode field. 1: modify existing entry, 0: add new station entry */
-#define STA_CONTROL_MODIFY_MSK 0x01
-
-/* key flags __le16*/
-#define STA_KEY_FLG_ENCRYPT_MSK cpu_to_le16(0x0007)
-#define STA_KEY_FLG_NO_ENC cpu_to_le16(0x0000)
-#define STA_KEY_FLG_WEP cpu_to_le16(0x0001)
-#define STA_KEY_FLG_CCMP cpu_to_le16(0x0002)
-#define STA_KEY_FLG_TKIP cpu_to_le16(0x0003)
-
-#define STA_KEY_FLG_KEYID_POS 8
-#define STA_KEY_FLG_INVALID cpu_to_le16(0x0800)
-/* wep key is either from global key (0) or from station info array (1) */
-#define STA_KEY_FLG_WEP_KEY_MAP_MSK cpu_to_le16(0x0008)
-
-/* wep key in STA: 5-bytes (0) or 13-bytes (1) */
-#define STA_KEY_FLG_KEY_SIZE_MSK cpu_to_le16(0x1000)
-#define STA_KEY_MULTICAST_MSK cpu_to_le16(0x4000)
-
-/* Flags indicate whether to modify vs. don't change various station params */
-#define STA_MODIFY_KEY_MASK 0x01
-#define STA_MODIFY_TID_DISABLE_TX 0x02
-#define STA_MODIFY_TX_RATE_MSK 0x04
-
-struct iwl3945_keyinfo {
- __le16 key_flags;
- u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
- u8 reserved1;
- __le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
- u8 key_offset;
- u8 reserved2;
- u8 key[16]; /* 16-byte unicast decryption key */
-} __attribute__ ((packed));
-
/*
* REPLY_ADD_STA = 0x18 (command)
*
u8 mode; /* 1: modify existing, 0: add new station */
u8 reserved[3];
struct sta_id_modify sta;
- struct iwl3945_keyinfo key;
+ struct iwl4965_keyinfo key;
__le32 station_flags; /* STA_FLG_* */
__le32 station_flags_msk; /* STA_FLG_* */
__le16 add_immediate_ba_ssn;
} __attribute__ ((packed));
-#define ADD_STA_SUCCESS_MSK 0x1
-#define ADD_STA_NO_ROOM_IN_TABLE 0x2
-#define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
-/*
- * REPLY_ADD_STA = 0x18 (response)
- */
-struct iwl3945_add_sta_resp {
- u8 status; /* ADD_STA_* */
-} __attribute__ ((packed));
-
/******************************************************************************
* (4)
u8 payload[0];
} __attribute__ ((packed));
-#define RX_RES_STATUS_NO_CRC32_ERROR cpu_to_le32(1 << 0)
-#define RX_RES_STATUS_NO_RXE_OVERFLOW cpu_to_le32(1 << 1)
-#define RX_RES_PHY_FLAGS_BAND_24_MSK cpu_to_le16(1 << 0)
-#define RX_RES_PHY_FLAGS_MOD_CCK_MSK cpu_to_le16(1 << 1)
-#define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK cpu_to_le16(1 << 2)
-#define RX_RES_PHY_FLAGS_NARROW_BAND_MSK cpu_to_le16(1 << 3)
-#define RX_RES_PHY_FLAGS_ANTENNA_MSK cpu_to_le16(0xf0)
-
-#define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
-#define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
-#define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
-#define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
-#define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
-
-#define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
-#define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
-#define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
-#define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
-#define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
struct iwl3945_rx_frame_end {
__le32 status;
* This command must be executed after every RXON command, before Tx can occur.
*****************************************************************************/
-/* REPLY_TX Tx flags field */
-
-/* 1: Use Request-To-Send protocol before this frame.
- * Mutually exclusive vs. TX_CMD_FLG_CTS_MSK. */
-#define TX_CMD_FLG_RTS_MSK cpu_to_le32(1 << 1)
-
-/* 1: Transmit Clear-To-Send to self before this frame.
- * Driver should set this for AUTH/DEAUTH/ASSOC-REQ/REASSOC mgmnt frames.
- * Mutually exclusive vs. TX_CMD_FLG_RTS_MSK. */
-#define TX_CMD_FLG_CTS_MSK cpu_to_le32(1 << 2)
-
-/* 1: Expect ACK from receiving station
- * 0: Don't expect ACK (MAC header's duration field s/b 0)
- * Set this for unicast frames, but not broadcast/multicast. */
-#define TX_CMD_FLG_ACK_MSK cpu_to_le32(1 << 3)
-
-/* 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
- * Tx command's initial_rate_index indicates first rate to try;
- * uCode walks through table for additional Tx attempts.
- * 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
- * This rate will be used for all Tx attempts; it will not be scaled. */
-#define TX_CMD_FLG_STA_RATE_MSK cpu_to_le32(1 << 4)
-
-/* 1: Expect immediate block-ack.
- * Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
-#define TX_CMD_FLG_IMM_BA_RSP_MASK cpu_to_le32(1 << 6)
-
-/* 1: Frame requires full Tx-Op protection.
- * Set this if either RTS or CTS Tx Flag gets set. */
-#define TX_CMD_FLG_FULL_TXOP_PROT_MSK cpu_to_le32(1 << 7)
-
-/* Tx antenna selection field; used only for 3945, reserved (0) for 4965.
- * Set field to "0" to allow 3945 uCode to select antenna (normal usage). */
-#define TX_CMD_FLG_ANT_SEL_MSK cpu_to_le32(0xf00)
-#define TX_CMD_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
-#define TX_CMD_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
-
-/* 1: Ignore Bluetooth priority for this frame.
- * 0: Delay Tx until Bluetooth device is done (normal usage). */
-#define TX_CMD_FLG_BT_DIS_MSK cpu_to_le32(1 << 12)
-
-/* 1: uCode overrides sequence control field in MAC header.
- * 0: Driver provides sequence control field in MAC header.
- * Set this for management frames, non-QOS data frames, non-unicast frames,
- * and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
-#define TX_CMD_FLG_SEQ_CTL_MSK cpu_to_le32(1 << 13)
-
-/* 1: This frame is non-last MPDU; more fragments are coming.
- * 0: Last fragment, or not using fragmentation. */
-#define TX_CMD_FLG_MORE_FRAG_MSK cpu_to_le32(1 << 14)
-
-/* 1: uCode calculates and inserts Timestamp Function (TSF) in outgoing frame.
- * 0: No TSF required in outgoing frame.
- * Set this for transmitting beacons and probe responses. */
-#define TX_CMD_FLG_TSF_MSK cpu_to_le32(1 << 16)
-
-/* 1: Driver inserted 2 bytes pad after the MAC header, for (required) dword
- * alignment of frame's payload data field.
- * 0: No pad
- * Set this for MAC headers with 26 or 30 bytes, i.e. those with QOS or ADDR4
- * field (but not both). Driver must align frame data (i.e. data following
- * MAC header) to DWORD boundary. */
-#define TX_CMD_FLG_MH_PAD_MSK cpu_to_le32(1 << 20)
-
-/* HCCA-AP - disable duration overwriting. */
-#define TX_CMD_FLG_DUR_MSK cpu_to_le32(1 << 25)
-
-/*
- * TX command security control
- */
-#define TX_CMD_SEC_WEP 0x01
-#define TX_CMD_SEC_CCM 0x02
-#define TX_CMD_SEC_TKIP 0x03
-#define TX_CMD_SEC_MSK 0x03
-#define TX_CMD_SEC_SHIFT 6
-#define TX_CMD_SEC_KEY128 0x08
-
/*
* REPLY_TX = 0x1c (command)
*/
struct iwl3945_rate_scaling_info table[IWL_MAX_RATES];
} __attribute__ ((packed));
-/*
- * REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
- *
- * 3945 and 4965 support hardware handshake with Bluetooth device on
- * same platform. Bluetooth device alerts wireless device when it will Tx;
- * wireless device can delay or kill its own Tx to accommodate.
- */
-struct iwl3945_bt_cmd {
- u8 flags;
- u8 lead_time;
- u8 max_kill;
- u8 reserved;
- __le32 kill_ack_mask;
- __le32 kill_cts_mask;
-} __attribute__ ((packed));
-
-/******************************************************************************
- * (6)
- * Spectrum Management (802.11h) Commands, Responses, Notifications:
- *
- *****************************************************************************/
-
-/*
- * Spectrum Management
- */
-#define MEASUREMENT_FILTER_FLAG (RXON_FILTER_PROMISC_MSK | \
- RXON_FILTER_CTL2HOST_MSK | \
- RXON_FILTER_ACCEPT_GRP_MSK | \
- RXON_FILTER_DIS_DECRYPT_MSK | \
- RXON_FILTER_DIS_GRP_DECRYPT_MSK | \
- RXON_FILTER_ASSOC_MSK | \
- RXON_FILTER_BCON_AWARE_MSK)
-
-struct iwl3945_measure_channel {
- __le32 duration; /* measurement duration in extended beacon
- * format */
- u8 channel; /* channel to measure */
- u8 type; /* see enum iwl3945_measure_type */
- __le16 reserved;
-} __attribute__ ((packed));
-
-
-#define HW_CARD_DISABLED 0x01
-#define SW_CARD_DISABLED 0x02
-#define RF_CARD_DISABLED 0x04
-#define RXON_CARD_DISABLED 0x10
-
-struct iwl3945_ct_kill_config {
- __le32 reserved;
- __le32 critical_temperature_M;
- __le32 critical_temperature_R;
-} __attribute__ ((packed));
-
/******************************************************************************
* (8)
* Scan Commands, Responses, Notifications:
__le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
} __attribute__ ((packed));
-/**
- * struct iwl3945_ssid_ie - directed scan network information element
- *
- * Up to 4 of these may appear in REPLY_SCAN_CMD, selected by "type" field
- * in struct iwl3945_scan_channel; each channel may select different ssids from
- * among the 4 entries. SSID IEs get transmitted in reverse order of entry.
- */
-struct iwl3945_ssid_ie {
- u8 id;
- u8 len;
- u8 ssid[32];
-} __attribute__ ((packed));
-
-/* uCode API-1 take 4 probes */
-#define PROBE_OPTION_MAX_API1 0x4
-#define TX_CMD_LIFE_TIME_INFINITE cpu_to_le32(0xFFFFFFFF)
-#define IWL_GOOD_CRC_TH cpu_to_le16(1)
-#define IWL_MAX_SCAN_SIZE 1024
/*
* REPLY_SCAN_CMD = 0x80 (command)
struct iwl3945_tx_cmd tx_cmd;
/* For directed active scans (set to all-0s otherwise) */
- struct iwl3945_ssid_ie direct_scan[PROBE_OPTION_MAX_API1];
+ struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX_API1];
/*
* Probe request frame, followed by channel list.
u8 data[0];
} __attribute__ ((packed));
-/* Can abort will notify by complete notification with abort status. */
-#define CAN_ABORT_STATUS cpu_to_le32(0x1)
-/* complete notification statuses */
-#define ABORT_STATUS 0x2
-
-/*
- * REPLY_SCAN_CMD = 0x80 (response)
- */
-struct iwl3945_scanreq_notification {
- __le32 status; /* 1: okay, 2: cannot fulfill request */
-} __attribute__ ((packed));
-
-/*
- * SCAN_START_NOTIFICATION = 0x82 (notification only, not a command)
- */
-struct iwl3945_scanstart_notification {
- __le32 tsf_low;
- __le32 tsf_high;
- __le32 beacon_timer;
- u8 channel;
- u8 band;
- u8 reserved[2];
- __le32 status;
-} __attribute__ ((packed));
-
-#define SCAN_OWNER_STATUS 0x1;
-#define MEASURE_OWNER_STATUS 0x2;
-
-#define NUMBER_OF_STATISTICS 1 /* first __le32 is good CRC */
-/*
- * SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
- */
-struct iwl3945_scanresults_notification {
- u8 channel;
- u8 band;
- u8 reserved[2];
- __le32 tsf_low;
- __le32 tsf_high;
- __le32 statistics[NUMBER_OF_STATISTICS];
-} __attribute__ ((packed));
-
-/*
- * SCAN_COMPLETE_NOTIFICATION = 0x84 (notification only, not a command)
- */
-struct iwl3945_scancomplete_notification {
- u8 scanned_channels;
- u8 status;
- u8 reserved;
- u8 last_channel;
- __le32 tsf_low;
- __le32 tsf_high;
-} __attribute__ ((packed));
-
-
/******************************************************************************
* (9)
* IBSS/AP Commands and Notifications:
struct iwl39_statistics_div div;
} __attribute__ ((packed));
-/*
- * REPLY_STATISTICS_CMD = 0x9c,
- * 3945 and 4965 identical.
- *
- * This command triggers an immediate response containing uCode statistics.
- * The response is in the same format as STATISTICS_NOTIFICATION 0x9d, below.
- *
- * If the CLEAR_STATS configuration flag is set, uCode will clear its
- * internal copy of the statistics (counters) after issuing the response.
- * This flag does not affect STATISTICS_NOTIFICATIONs after beacons (see below).
- *
- * If the DISABLE_NOTIF configuration flag is set, uCode will not issue
- * STATISTICS_NOTIFICATIONs after received beacons (see below). This flag
- * does not affect the response to the REPLY_STATISTICS_CMD 0x9c itself.
- */
-#define IWL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
-#define IWL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
-struct iwl3945_statistics_cmd {
- __le32 configuration_flags; /* IWL_STATS_CONF_* */
-} __attribute__ ((packed));
-
/*
* STATISTICS_NOTIFICATION = 0x9d (notification only, not a command)
*
* appropriately so that each notification contains statistics for only the
* one channel that has just been scanned.
*/
-#define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
-#define STATISTICS_REPLY_FLG_FAT_MODE_MSK cpu_to_le32(0x8)
struct iwl3945_notif_statistics {
__le32 flag;
struct statistics_rx rx;
} __attribute__ ((packed));
-/*
- * MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
- */
-/* if ucode missed CONSECUTIVE_MISSED_BCONS_TH beacons in a row,
- * then this notification will be sent. */
-#define CONSECUTIVE_MISSED_BCONS_TH 20
-
-struct iwl3945_missed_beacon_notif {
- __le32 consequtive_missed_beacons;
- __le32 total_missed_becons;
- __le32 num_expected_beacons;
- __le32 num_recvd_beacons;
-} __attribute__ ((packed));
-
-/******************************************************************************
- * (11)
- * Rx Calibration Commands:
- *
- *****************************************************************************/
-
-#define PHY_CALIBRATE_DIFF_GAIN_CMD (7)
-#define HD_TABLE_SIZE (11)
-
-struct iwl3945_sensitivity_cmd {
- __le16 control;
- __le16 table[HD_TABLE_SIZE];
-} __attribute__ ((packed));
-
-struct iwl3945_calibration_cmd {
- u8 opCode;
- u8 flags;
- __le16 reserved;
- s8 diff_gain_a;
- s8 diff_gain_b;
- s8 diff_gain_c;
- u8 reserved1;
-} __attribute__ ((packed));
-
-/******************************************************************************
- * (12)
- * Miscellaneous Commands:
- *
- *****************************************************************************/
-
-/*
- * LEDs Command & Response
- * REPLY_LEDS_CMD = 0x48 (command, has simple generic response)
- *
- * For each of 3 possible LEDs (Activity/Link/Tech, selected by "id" field),
- * this command turns it on or off, or sets up a periodic blinking cycle.
- */
-struct iwl3945_led_cmd {
- __le32 interval; /* "interval" in uSec */
- u8 id; /* 1: Activity, 2: Link, 3: Tech */
- u8 off; /* # intervals off while blinking;
- * "0", with >0 "on" value, turns LED on */
- u8 on; /* # intervals on while blinking;
- * "0", regardless of "off", turns LED off */
- u8 reserved;
-} __attribute__ ((packed));
-
/******************************************************************************
* (13)
* Union of all expected notifications/responses:
struct iwl3945_rx_packet {
__le32 len;
- struct iwl3945_cmd_header hdr;
+ struct iwl_cmd_header hdr;
union {
struct iwl3945_alive_resp alive_frame;
struct iwl3945_rx_frame rx_frame;
struct iwl3945_error_resp err_resp;
struct iwl_card_state_notif card_state_notif;
struct iwl3945_beacon_notif beacon_status;
- struct iwl3945_add_sta_resp add_sta;
+ struct iwl_add_sta_resp add_sta;
struct iwl_sleep_notification sleep_notif;
struct iwl_spectrum_resp spectrum;
struct iwl3945_notif_statistics stats;